Search Documents

By John C. Machisak

Statistical data on injuries in the metal and nonmetal industry of the United States first became available to the Bureau of Mines by collecting reports from the operators for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1954, is the 31st publication (1933-34 was published as Bulletin 398) containing statistical data on injuries at metal and nonmetal mines and related plants, and it 1s the first such bulletin to be published since 1942. The last publication was Bulletin 461, Metal and Nonmetal-Mine Accidents in the United States, 1942. The unpublished statistics for 1943-53 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries and related employment at metal and nonmetal mines, but there is no Federal law that compels operators to submit such information. Therefore, all materials submitted are voluntary responses to the Bureau's requests for information. The figures presented herein may not be complete for the entire industry, nevertheless, every effort has been made to make them so, and the data given are believed to be representative of the hazards to which metal and nonmetal workers are exposed. Moreover, the figures are comparable as between States-which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1957

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests.

Jan 1, 1957

By J. P. Hansen

In order to help assure an adequate domestic supply of minerals essential to the Nation's economy and and security by developing more efficient minerals extraction technologies, the Bureau of Mines Tuscaloosa Research Center examined the application of autogenous microgrinding to calcium carbonate minerals. Treatment of minus 8-mesh Alabama marble resulted in a product 80 pct minus 5 micrometers (µm) at a power consumption of 70 to 80 kwhr/ton, This study shows that coarse particles of calcium carbonate minerals are effective as the grinding media for the autogenous attrition grinding of these minerals. The minus 8- plus 30-mesh fraction is an effective grinding medium (sand) for particles smaller than 30 mesh. A 40-pct-solids slurry and a sand: marble ratio of 2.5 appeared to be near optimum. For residence times above 13 minutes, products were greater than 80 pet minus 5 µm and greater than 54 pct minus 2 µm. Power consumption was uniformly low, ranging from 50 to 100 kwhr/ton of product depending upon the feed rate. One marble sample from Georgia was shown to be the most persistent grinding medium, with losses of less than half those of the other materials tested.

Jan 1, 1980

By Gerald V. Gibbs

As a part of the Bureau of Mines long-range program in asbestos, synthetic asbestiform compounds and minerals were prepared and described. Fundamental structural data on two such compounds are given in this report. Crystallographic data are provided for the synthetic isotypic compounds potassium-lead silicate, K2.Pb4 -Si8021 (I), and lead-aluminum silicate, Pb2. Pb4 .Al2Si6O21 (II). The space group symmetry 14/mmm was assigned provisionally to I and II on evidence of single crystal and piezoelectric measurements. A statistical evalua¬tion of indexed powder diffraction data revealed the cell edtes of I to be a 11.816 and c 7.932A and those of II to be a 11.723 and c 8.044A. The phases are uniaxial with observed refractive indices eD 1.790, an ?D,699 and eD 1.884, cusp 1,807, respectively. The atomic structure of I and II may be based on a complex of chains of silicon-oxygen tetrahedra lying along the c cell edge similar to the type of chain structure postulated by Pauling for scapolite. K2.Pb4.Si8021 and Pb2.Pb4 Al2Si6021 were first described by Geller and Bunting (5, 6)4 as fibrous compounds similar in crystal habit to asbestos. These authors gave powder diffraction data, although no attempt was made to find the cell edges or to index the powder diffraction patterns. Later, Shell and others (9) conducted a crystallochemical study of these fibrous silicates in search of a substitute for strategic asbestos. Their single crystal data revealed K2.Pb4 -Si8021 to be tetragonal body-centered with cell edges a 11.66, c 7.95 A. Pb2.Pb4 Al2Si6021 was concluded to be isotypic with K2.Pb4 -Si8021 on the basis of similar powder diffraction patterns, chemistry, and physical properties. No attempt was made, however, to index the powder diffraction record nor to determine the appropriate space group of either compound.

Jan 1, 1962

This publication summarizes, for potential contractors and other interested parties, the proposed research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1977 (October 1, 1976-September 30, 1977) under its Advancing Coal Mining Technology program. The objective of these projects is to provide an ordered and sequenced series of advances toward the overall goal of providing the system technology required to increase the productivity of the coal mining process.

Jan 1, 1977

By T. E. Ackman

Scale inhibitors and slow-release polymers were tested by the Bureau of Mines at mine drainage treatment facilities. The scale inhibitors were investigated to determine their effectiveness in controlling gypsum (CaSO4) scale; the polymers were investigated to determine their effectiveness for increasing settling rates of suspended iron hydroxide. Two types of scale inhibitors were tested at a site having a severe CaSO4 scaling problem. Both proved to be effective in controlling scale formation; in addition, one caused the dissolution of CaSO4 deposits. Slow-release polymers were tested at three mine drainage treatment facilities. These gelatinous polymeric flocculants were found to be convenient and easy to use, but only effective when pH could be controlled.

Jan 1, 1984

By John B. Bennett

In this report estimates are presented of the impact of the passage of five recently proposed "acid rain" bills on electric utility costs for coal-burning utilities servicing the domestic aluminum smelting industry, and on the costs of production for affected aluminum smelters. As aluminum smelting is an energy-intensive industry, domestic increases in electricity prices could affect the industry's competitiveness. Energy costs in U.S. aluminum smelting are compared to aluminum smelting energy costs in the rest-of-the-world. Governmental policies affecting these energy costs are discussed.

Jan 1, 1988

By W. R. Hardwick

Nuclear explosive fracturing has been suggested as a method to make hard rock amenable to extraction by a modified block-caving method. To evaluate this possibility, conventional and nuclear blasting practices are discussed, underground mining methods for large deposits and their costs are described, and the cost of fracturing ore with a nuclear explosive and subsequent mining by a modified caving system is estimated and compared with both open-stope and block-caving mining costs. While the direct cost of fracturing the ore in hard rock with a nuclear explosive is less than with conventional explosives, additional costs imposed by the use of nuclear explosives may make their use unattractive for deep mining.

Jan 1, 1970

By W. P. Haynes, J. W. Mulvihill, G. B. Taylor, S. Katell

Capital and operating costs have been estimated for separating methane and hydrogen in gas - separating plants designed to produce 90 million scf per day of product gas containing a minimum of 90 percent methane . After a preliminary literature review of various separation techniques , three different processes --moving - bed adsorption using active carbon , oil absorption , and liquefaction -- were chosen for the cost estimates . Three different methane feed gas concentrations , 5 , 20 , and 50 percent ( cases 1 , 2 , and 3 , respectively ) , were chosen as representative methane concentrations for the separation estimates . Capital and operating costs were lowest for the moving - bed adsorption process in all three cases investigated . Operating costs declined from $ 0.24 to $ 0.06 per 1,000 cu ft of product gas , and capital costs declined from $47,490,800 to $7,411,200 as the percentage of methane in the feed gas increased from 5 to 50 percent .

Jan 1, 1964

By G. L. Oldright

The data presented in this paper were collected et the smelter of the Consolidated Mining A Smelting Co. of Canada, Limited, Trail (Tadanac), British Columbia, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent, George Murray, assistant smelter superintendent; and the staff members listed in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the twelfth of a series on smelting in the lead blast furnace and the fifth4 dealing with blast-furnace gases.

Jan 1, 1934

By Frank B. Fulkerson

Three of the five primary aluminum producers in the Pacific Northwest have facilities in the region to make aluminum mill products. Only one of the three, however, produces a variety of shapes and forms. The principal reason for the lag in development of an aluminum mill products industry was found to be transportation cost. The long range outlook is for expansion, based mainly on growth of the western market for aluminum used in construction, containers and packaging, electrical applications, diesel trucks, mobile homes, and irregation pipe. Consumption of western aluminum mill products in 1985 is projected at 1.1 million tons, compared with estimated consumption of 250,000 tons in 1961.

Jan 1, 1965

By G. L. Oldright

This paper is the twelfth of a series on smelting in the lead blast furnace and the fifth dealing with blast-furnace gases. It was noted in Report of Investigations 2957 that the gases evolved from the top of the lead blast furnace at Tooele were similar in composition to those from the top of an iron blast furnace. It was noted in Report of Investigations 3095 that at Kellogg, where a smaller percentage of coke on charge and shorter stock column were employed, the gases evolved were much less reducing. At times there was a considerable amount of oxygen in the top gases at the second plant. More SO2 was also evolved from sulphides in the charge. Then operations were conducted as at Kellogg, the gases were alternately reducing and oxidizing. This paper deals with the gases evolved in smelting a charge containing more zinc than at either of the other two plants with about the same amount of coke as was used at Kellogg,: To compare other factors influencing the composition of the gases, it may be noted that at Tooele the approximate height of the charge column was 15 feet, at Kellogg 9 feet and at Trail 13 feet. The furnaces have about the -same cross-sectional area- tog. The furnaces at Tooele are about 6 inches wider at the tuyeres, being 54 inches wide against 48 for the other two plants. At Tooele and Kellogg the furnaces are fed at the top from bottom-dump cars. At Trail the charges are dumped from Decauville cars (bottom cars which dump when tilted), which run on tracks placed on both sides of the blast furnaces. The hoods through which the waste gases are conducted are directly above the shafts of the furnaces. The flues for removing the effluent gases lead off from under the charge floor at Tooele and Kellogg. (Charging and distribution of the feed in the furnace covered later in a rate paper of series.)

Jan 1, 1934

By R. H. Nicholas

Shuttle cars have undeniably proved their worth as a means of transporting coal underground; however, several factors have arisen in connection with their possible improvement. This report .discusses the effect of shuttle cars that employ rough-tread and smooth-tread tires on mine roadbed, the amount of dust thrown into suspension by the use of such tire treads, and the service rendered by each type of tire. Involved, also, in this study are observations on the use of different amounts of calcium chloride on the haulageways.

Jan 1, 1949

By Franklin H. Persse

Domestic bismuth supply was projected from production figures for the ores in which it occurs--copper, lead, zinc, and tungsten. Published and unpublished data concerning host ores were examined to determine bismuth reserves and resources, and mine production. Potential recoverable bismuth occurring with reserves and resources of copper, lead, and zinc was estimated to be 36.3 million pounds. A bismuth availability diagram was developed from quantity estimates and ratios of production cost to value for these host ores. Additional recoverable bismuth occurring with domestic tungsten reserves was estimated to be 1.5 million pounds. Domestic byproduct production of bismuth will approximate 1.3 million pounds annually by 1980. This quantity will provide about 37 percent of the 3.5-million-pound estimated requirement for that year. Known world supply of bismuth appears to be sufficient for world demand to the end of this century. The study indicates that bismuth reserves and potential resources in the rest of the world have not been adequately reported.

Jan 1, 1970

By Robert E. Barieau

In the design of plants to separate helium from natural gas , it is necessary to estimate the enthalpies of the various streams at various positions in the process . This Bureau of Mines report surveys the various methods that have been used to determine enthalpies and gives information on the organizations with such capabilities . The minimum information required for developing an enthalpy diagram is presented , and the relative merits of the various methods are discussed . It is concluded that methods that require no mass flow rate or energy measurements are to be preferred .

Jan 1, 1965

By Sidney Katell

This report covers the period January 1962 through December 1962; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the fourth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load evolved in the preparation shared equally. Tile abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from tile following sources:

Jan 1, 1963

By Sidney Katell

This report covers the period January 1962 through December 1962; it is a continuation of the series that began with the publication of Information Circular 7510 in October 1949. Also, it is the fourth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load evolved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from tile following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Utilization. 9. Cost Engineering. 10. Hydrocarbon Processing and Petroleum Refiner. 11. Industrial and Engineering Chemistry. 12. Nucleonics. 13. Oil and Gas Journal. 14. Petroleum Management. 15. World Oil.

Jan 1, 1963

By G. S. Scott, W. J. Huff, G. W. Jones, R. E. Kennedy

"INTRODUCTION This report gives preliminary results of field and laboratory investigations made at the request of the War Production Board relative to causes that have occurred during the last 8 months in acetylene-generat72,r plants in shipyards on the Pacific coast.Six acetylene-generator explosions have occurred in four shipyards. These explosions killed five operators, injured six others, and extensive damage to the plants involved and curtailmnent of vital defense Although the occurrence of acetyiene-generator explosions in other section of the United States is not known, it appears, at least, that if such have occurred, they have caused only minor damage and no loss of lives.The use of acetylene in shipyards on the west coast has expanded tremendously during the past 2 years. These shipbuilding, companies erected aletylene-generatcr equipment, which was soon found to be entirely inadequate to meet the needs of their expanding acetylene requirements for welding, cutting, shrinking, and other purposes, and instances found it necessary to operate their equipment at rates greater than deemed consistent with safe operating practice."

May 1, 1944

By Howard F. Carl

"INTRODUCTION Talc is a hydrous magnesium silicate mineral found throughout the world in deposits of economic importance. This mineral occurs in different physical forms and varying degrees of purity, both of which affect its ultimate commercial usage. Talc is used in finely ground condition by the ceramic, paint, paper, rubber, cosmetic, and other industries. Most domestic talc production is of this type. Talc also occurs, although much less frequently, in massive, fine-grained, fairly homogeneous bodies; the impure varieties are the familiar soapstones, and the purer form is frequently called ""steatite."" Because of certain properties, the purest grades of this massive variety have a monetary value about 20 times that of the ground talc.One desirable property of this massive talc is its amenability to accurate cutttng, machining, and working in many ways, similar to a hard wood or soft metal, and then firing without warping or appreciable shrinkage into a hard, refractory ceramic body. Consequently, shapes that cannot be formed conveniently by molding and pressing can be produced readily with ordinary machine tools. When talc is fired to about 1,100° C., it is converted to a ceramic body with certain very desirable physical properties. This fired material has a hardness and toughness frequently superior to steel. It is a refractory and an exceptionally good electrical insulator. When formed from a high-grade talc essentially free from iron, it has unusually low dielectric losees, even at very high frequencies."

Feb 1, 1945

By Heine Kenworthy

"INTRODUCTION In 1930 the Shenandoah-Dives Mining Co. near Silverton, Colo., put into operation a newly erected, 300-ton selective flotation plant to mill complex ores from its nearby mine. The operation was a steady producer and was enlarged to treat 600 to 800 tons a day. In 1942 the company opened and started milling an area in the mine containing semioxidized ore. The valuable mineral content of this ore was considerably higher than in, the straight sulfide ore previously handled alone. The mixture of clean sulfide and semi-oxidized ore was difficult to treat; consequently, tailing losses, especially with respect to lead, were high. A few years later, in order to study the possibilities of obtaining higher recoveries by a modification of the mill flow sheet, a 1,200-pound sample of mill, feed, taken over a period of several days by the company, was submitted to the Mississippi Valley Experiment Sta¬tion for testing-. Although this sample proved to contain more than twice as much lead as the average yearly mill feed, the same problem of recovering the oxidized values was present.A résumé of the ore-dressing treatment used in the Shenandoah-Dives mill follows. After crushing, the ore passes through a ball mill, the minus 5-mesh discharge of which is distributed to three tables. A finished lead concentrate is made on the tables, and the table tailing goes to the classifier which is in closed circuit with the ball mill. The classifier overflow is treated -by flotation to obtain a bulk sulfide concentrate at a relatively coarse size. The bulk concentrate is thickened and reground to about 95 percent minus 325-mesh before flotation treatment to separate a lead-copper and a zinc concentrate. A typical monthly average showed that the table concentrate contained about 45 percent lead, 1 percent copper, 4 percent zinc, 12 ounces of gold, and 40 ounces of silver; that the lead flotation concentrate contained '35 percent load, 6 percent copper, 7 percent zinc, 3.5 ounces of gold, and 50 ounces of silver; and that the zinc flotation concentrate contained 2 percent lead, 0.5 percent copper, 60 percent zinc, 0.15 ounces of gold, and 4 ounces of silver. Recoveries in salable products were roughly b5 percent of the lead, 70 percent of the copper, 45 percent of the zinc, 85 percent of the gold, and b5 percent of the silver."

May 1, 1948