Search Documents

By D. C. Dahlin

The Bureau of Mines conducted laboratory batch beneficiation tests on samples from four potential platinum resources in southeastern Alaska to concentrate platinum and other precious metals. Thin Investigation was done as part of the mission of the Bureau to insure an adequate supply of minerals to meet the Nation's needs. Petrographic studies and beneficiation methods including gravity concentration, froth flotation, and magnetic separation were used to determine mineral association and to attempt to concentrate the platinum values with a primary mineral value such as chromite, copper sulfide, or magnetite. A high-graded sample from the Salt Chuck copper sulfide deposit yielded the platinum-group metal concentrate; the maximum grade attained was 0.04 oz Pt and 1.5 oz Pd per ton of high-grade copper sulfide concentrate. The other samples yielded low-grade primary mineral concentrates with low platinum-group values, and/or the platinum-group metals did not concentrate with the primary mineral value.

Jan 1, 1981

By Arthur J. Hudson, Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion- proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures, a multicompartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 1992

By I. AITKENS

The precious stones rubies and sapphires are transparent varieties of the mineral corundum . Essentially they are aluminum oxide , but the aluminum is often replaced. by small amounts of chromium , titanium , or iron . The chromium is said to give a red color , titanium a blue , and iron a yellow . True rubies range from rose to a somewhat purplish red and are sometimes termed " oriental rubies " to distinguish them from spinel rubies , stones of inferior hardness , density , and value . " Oriental rubies " are very rare , and the so-called " pigeon's blood" variety is the most valuable . Sapphires normally range in color from palest blue to deepest indigo , but actually all precious varieties of corundum of any other color than red are called sapphires . The most esteemed tint is like that of the blue cornflower . Colorless corundum of gem quality is called white sapphire ; the yellow variety is described either as yellow or as golden sapphire ; and the pale pink is classed as pink sapphire . The word " oriental " is also used as a prefix in naming varieties of corumdum of less popular colors . For instance , oriental emerald is used for green corundum, oriental topaz for yellow , and oriental amethyst for violet to purple varieties . The chief physical characteristics of rubies and sapphires are hardness , adamantine luster , and moderately high specific gravity ( 3.9 to 4.1) . Next to the diamond, corundum is the hardest of all minerals ; in fact , the sapphire is number 9 on Moh's scale , ranking between the topaz and the diamond. Rubies crystallize in 6-sided prisms terminated by flat faces and other varieties of corundum with twelve inclined faces , six above and six below , meeting in a girdle . Corundum is doubly refractive , with a direction of single refraction running parallel to the edge of the prism . The refractive indexes are very constant, the ordinary index ranging from 1.766 to 1.774 and the extraordinary index from 1.757 to 1.765. The double refraction always remains the same.

Aug 1, 1931

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, increased about 4% in 1990. The decrease in the value of tripoli production was the result of a decrease in total production. Emery decreased owing to a decrease in the volume of the material produced. Special silica stone experienced a decrease in unit value and in the quantity produced. Garnet showed an 8 % increase in quantity and an 8 % increase in unit value. Staurolite increased about 38 % in the quantity produced, and the value of production increased about 36 %. The fused aluminum oxide industry showed a 12 % decline in the quantity produced and a 13 % decline in the value of production. The silicon carbide industry saw a 47 % decrease in the quantity produced and a 23 % decrease in the value of production. Combined, the industries decreased 17 % in quantity and value compared with those of 1990.

Jan 1, 1993

By David T. Couillard

Task training is increasingly important in mining operations because of the ever-accelerating pace of technological innovations and the concomitant increasing complexity of mining equipment. This Bureau of Mines report describes two successful task training program In use in two open-pit taconite operations in northeastern Minnesota. The programs are different in approach, but both have improved safety and in- creased productivity while lowering costs. Methods of training both before and after passage of the 1977 Mine Safety and Health Act are described, and the impact of this act on task training at each operation is discussed. The report identifies four common principles that have contributed to the success of the two training programs and presents plans each operation has for improving future training through new technology.

Jan 1, 1984

By Alfred E. Schwaneke

A new high-temperature soft soldering system has been developed by the Bureau of Mines for use on copper, copper alloys, and low-carbon steel; the method is applicable to automobile radiators and home appliances. The system uses a unique sacrificial metal coating method to promote spontaneous wetting and spreading of zinc and zinc alloy solder: on metallic substrates. The 10-5 to 10-6 cm thick, electroplated or sputtered, sacrificial nickel coating is absorbed by the molten filler alloy during soldering and produces a direct solder-substrate metallic bond. Preliminary measurements on butt joints with copper members give tensile strengths up to 22,000 psi at room temperature using 95 Zn-5 Al alloy as solder. Spontaneous wetting, spreading, and capillary penetration are extremely rapid and produce joints as easily as 50-50 tin-lead solders. Recrystallization or annealing of the wrought copper joint members is negligible at the soldering temperatures of 450° to 490° C and lower. A list of fluxes and solder alloys is included in the report.

Jan 1, 1970

By Bernadette Michalski

Although hydrocarbons accounted for more than 60% of Bahrain's income and more than 80% of export earnings, this island nation sustained one of the more diversified economies in the Gulf Region. The availability of low-cost natural gas for electric power has fostered the development of a significant aluminum refining and manufacturing industry with emphasis on vertical integration. The Bahraini iron pelletization plant, closed since 1986 due to financial problems, was scheduled to reopen by early 1989. Commodity Review Metals.-Aluminum.-Aluminium Bah-rain Bsc (Alba) attained record high production levels in 1988 taking advantage of favorable aluminum prices, which averaged over $2,000 per ton as compared with less than $1,500 per ton in 1987. Net aluminum production was nearly 13,000 tons over design capacity. Fewer standard ingots (52,081 tons as compared with 79,685 in 1987) were produced as Alba concentrated on higher value added products such as rolling ingots (42,324 tons as compared with 32,125 tons) and extrusion billets (60,934 tons as compared with 46,618 tons).

Jan 1, 1990

By M. A. Elliott, F. W. Brown

"INTRODUCTION During the recent war the Bureau of Mines, at the request of one of the armed services, investigated the hazards that night be encountered 5n handling perchloric acid, particularly if spilled on certain materials. The hazardous nature of perchloric acid when mixed with reducing agents had been known qualitatively, but it was desired to obtain quantitative data on the explosion hazards of such materials. Accordingly, tests were made to determine the sensitivity of mixtures of perchloric acid and oxidizable materials to initiation by heat, impact, sparks, flame, and explosive impulses. This report summarizes the results of those tests.PROPERTIES OF PERCELORIC ACIDAnhydrous perchloric acid is a colorless,hygroscopic, volatile, mobile liquid that fumes in the air. The anhydrous acid is unstable at ordinary temperatures, and therefore the commercial acid is a water solution containing either 60 percent or 70 percent by weight of the anhydrous acid. The commercial acid is widely used in chemical analysis, frequently to oxidize organic material. If proper precautions are not observed, such an oxidixation may become exceedingly rapid and result in an explosion. Several such explosions involving the acid are mentioned in the literature. 4, 5, 6/"

Jan 1, 1948

By John G. Kovac

A computer simulation has been developed to estimate the chances of a miner making a successful escape while wearing a SCSR. The model takes into account: (1) training in the use of SCSRs, (2) apparatus integrity, and (3) the oxygen cost of a mine escape. This Bureau of Mines report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By J. W. Walkiewicz

Studies were conducted by the Bureau of Mines to develop a method for fabricating Sm-Co permanent magnets. This method consisted of arc-melting, crushing and grinding the alloy, alining and pressing the powder, and sintering the green compacts. Results indicated that the optimum composition was 36.7±0.3 weight-percent Sm and 63.3±0.3 weight-percent Co. This composition was obtained by blending together Sm2C07 and SmCo5. The maximum values exper¬imentally obtained were MHC = 27.4 kOe, BHc = 7,510 Oe, Br = 7,810 G, and (BH)max = 15.1 MGOe. The optimum sintering temperatures and grinding times for maximum MHc and (BH)max were determined. Lowering the grinding temperature from 0° C to -60° C resulted in a significant increase of magnetic properties.

Jan 1, 1973

By G. F. Friel

A series of experiments in the U.S. Bureau of Mines Safety Research Coal Mine at the Pittsburgh Research Center evaluated the effects of crosscuts on the travel time of carbon monoxide (CO) along an entry to improve the accuracy of a mine-fire locator program. Three entries, ten single crosscuts, and three double crosscuts were instrumented with CO sensors. One-percent CO in nitrogen was released and monitored as it traveled the entries. In addition to dispersion of CO at the front of the CO wave, CO was entrained from the entry into the crosscuts. It was determined for an entry and single-crosscut configuration that the measured travel time for a concentration change of 5 ppm was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and crosscut volumes. For an entry and double-crosscut configuration, the measured travel time for the same concentration change was 25% greater than the predicted time based upon entry volume only, but 10% less than the predicted time based upon entry and crosscut volumes. An effective dispersion coefficient for CO dispersion along one of the entries was estimated to be 1.5 m2/ s.

Jan 1, 2010

By Jeffrey S. Newman

This report establishes a methodology for the evaluation of gas detection devices and is the result of a critical investigation into the basic principles defining gas detector performance. A scheme is presented to evaluate the performance of a test sample of gas detectors based on the detector type and intended application. Test procedures, worksheets, test apparatus, glossary and statistical methods for handling test data arc given. In addition, evaluation standards and test parameters are identified. It is intended that this report serve as a comprehensive framework for the eventual certification of all gas detectors for mine applications. A plan is proposed and recommended for the quantification and implementation of evaluation standards for gas detection device certification.

Jan 1, 1980

By O. C. Blade

The use of Diesel fuel as a source of power is continuing to increase in the United States. The latest available figures indicate that refineries are delivering in excess of 10,000,000 barrels of this type of fuel per month. Factors contributing to this increased consumption are conversions by a number of railroads from steam to Diesel locomotives and the growing use of Diesel engines in buses, trucks, tractors, earth-moving machinery, water craft, and stationary power plants. The increasing importance of Diesel fuel has led to a need for more information on its characteristics, particularly on the grades and qualities currently being marketed. To supply this information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under a cooperative agreement, are conducting annual surveys of Diesel fuels produced in refineries in this country. Samples of Diesel fuel were analyzed by the manufacturers in accordance with instructions from the Motor-Fuels Survey Panel of the Automotive Research Committee of the American Petroleum Institute. Results of the analyses were transmitted to the Bureau of Mines where the data were studied am compiled as shown in the tables of this report. The first survey was made in 1950 and was published as a Bureau of Mines report. The present report shows the results of a similar survey made during 1951.

Jan 1, 1951

By John L. Nieber

This information circular describes a computer program called VARSAT2D, a comprehensive unsaturated fluid flow simulator developed by the U.S. Bureau of Mines. VARSAT2D solves for either a vertical or horizontal, transient or steady-state solution in variably saturated, heterogeneous, anisotropic porous media using the Galerkin finite-element approach. Simplex triangular elements are used. Moisture retention characteristics are described by specifying either the Brooks and Corey, Brutsaert, or Van Genuchten power functions, with hysteresis described using the Maulem independent domain model. Boundary conditions may include any combination of time-varying seepage, pressure along solution domain, boundaries and/or at internal node points, unit hydraulic gradient at the lower boundary, and a uniform source and/or sink. This program should be a welcome addition for mining and environmental hydrologists, researchers, and engineers interested in modeling unsaturated fluid flow.

Jan 1, 1994

By M. R. Geer

This report presents the results of washability examinations of seven coals from the principal coal-producing fields of Montana. A complete performance test of the Baum-type jig operated at one of the mines is included, as are the results of cleaning tests made on two of the coals in a dense-medium pilot plant. The coals examined from the Red Lodge, Bull Mountain, and Forsyth fields are comparatively easy to clean. Ash contents of 5 to 10 percent can be obtained at yields of washed coal ranging from 90 to 95 percent. The coal from the Great Falls field, however, could not be cleaned readily to less than 14 percent ash, and the rejection of impurity would amount to over 25 percent. The two coals treated in the dense-medium pilot plant were characterized by sharp separation of impurity, high recovery efficiency, and satisfactory reduction in ash content.

Jan 1, 1955

By E. P. Hayes

This report supplements the date contained in Bureau of Mines Information Circular 6156, "Special features of core drilling in the salt beds of Western Texas and New Mexico," by J. S. Wroth. That circular dealt with the drilling of the first 12 of the 24 potash tests made by the U. S. Bureau of Mines in cooperation with the U. S. Geological Survey; this report is concerned with the drilling of the last 12 tests. ACKNOWLEDGMENTS The writer is indebted to R. E. Heithecker, the Bureau of Mines engineer who had charge of the drilling of tests 13 to 17, for his well-prepared records on the drilling of these tests.

Jan 1, 1933

By Noel N. Moebs

This report summarizes a Bureau of Mines study on the use of geotechnology to identify and reduce ground control hazards at slate quarry operations in eastern Pennsylvania. The major ground control hazard is falling rock, attributed to weathered bedding plane faults, which weaken quarry highwalls. It was demonstrated that these faults can be detected outside of the quarry perimeter using surface resistivity measurements. Falls of ice from quarry highwalls constitute a second major hazard, which requires water diversion as a basic control method. In situ stresses seemingly cause only minor problems in slate extraction although they could interact with developed stresses and lead to failure of barriers between quarries. Pull tests showed that rockbolts anchor firmly in slate and should prove effective in securing loose rock.

Jan 1, 1986

By Raymond M. Stateham

The Bureau of Mines evaluated temperature increases on the heads of resin-grouted bolts as indicators of the integrity of the anchoring of the bolt. Expected increases were calculated by the finite difference method; the calculations were checked by bolthead temperature measurements, both in the laboratory and in the field. The accuracy of the calculations varies with the validity of assumptions necessary to the process. Measurements in the laboratory produced a temperature rise of about 4.00 F on the head of a 4-foot bolt when installed with a full column of resin. This increase remained for about 30 minutes. Similar increases were noted on bolts installed at the White Pine mine, White Pine, Mich., but bolthead temperature increases in the mine lasted only about 10 to 15 minutes. When partial columns (reduced amounts) were used, the temperature increases were smaller.

Jan 1, 1976

By Wilbert J. Huff

The organization of the'Explosives Division is indicated by the accompanying chart (fig. 1). As this has been discussed in a previous report3/, it will not be considered further in this report. The activities of the various units are outlined below. I. INFLAMMABILITY OF GASES AND VAPORS4/ Determination of the Explosion Hazards of Combustible Gases and Vapors Found in Mines and Industries The Explosives Division maintains, at the Pittsburgh Experiment Station, a laboratory specially equipped for the determination of the explosion hazards of combustible gases and vapors. Of particular importance, is the determination of the chemical composition within which explosions may occur and beyond which there is no danger of explosion, combustion or inflammation. These limits, known as the limits of inflammability, as determined by this and other laboratories, have been compiled in Bulletin 279 of this Bureau. The last revised edition (1931) of this bulletin has been exhausted. Since it was published, the Pittsburgh laboratory has determined the limits of about 40 combustibles and has ascertained more precisely and accurately many previously published limits.

Jan 1, 1938

By T. M. Barczak

One of the primary goals of Bureau of Mines research is to reduce the cost of coal mining by improving the efficiency of longwall supports. One method of achieving this goal is the optimization of stress distribution within the support structure, resulting in a lower overall weight, more fully stressed shield. However, before stress optimization can be initiated, load conditions must be defined that cause maximum stress in the various support components. A finite-element model of a longwall shield was used to identify these critical load conditions. These load conditions were then evaluated in the Bureau's mine roof simulator (MRS) by instrumentation of a longwall shield and measurement of strains in each of the shield components. The critical (canopy-base contact) load conditions were identified that can cause structural failure at less than rated shield (hydraulic yield) capacity. Comparisons were made between full-contact and partial-contact load conditions. Other parameters investigated included the stiffness of the contact material, changes in shield geometry, rate of load application, and effects of horizontal constraint. Conclusions were drawn regarding the structural integrity of the major shield components and potential for stress optimization.

Jan 1, 1987