Search Documents

By D. J. Parker

Before the various States began to enact workman's compensation laws accidents were considered inherent in many industries, and little or no effort was made to prevent or reduce them. The hazard was accepted by the employee with the job, and the avoidance of accidents by mental alertness or physical agility was largely his responsibility. After the employee had given evidence of enough skill inn performing his allotted task efficiently the responsibility of the employer apparently ceased with respect to the personal safety of the employee. However, following the enactment of workmen's compensation laws, at least two facts that had not before been fully appreciated soon became apparent: (1) The majority of accidents can be prevented if the management firmly determines to prevent them; (2) frog a monetary point of view alone accidents are decidedly expensive, both to employer and to employee. It is now evident that savings effected by conscientious safety effort add substantially to net profits of operation.

Jan 1, 1934

By Akul Joshi, Ming C. Leu, Robert Guttenberg, Susan L. Murray

The aerospace and automotive industries are facing a significant risk for cumulative trauma disorders from high-repetition, long-duration tasks. Additional risk factors such as shocks, vibrations and sustained uncomfortable postures oftentimes contribute to musculoskeletal, neurological injuries associated with the hand-arm system. The power tools used for the operation reduce the comfort and working efficiency of the operators, thus lowering their health and safety and the quality of operation. This paper investigates the fastening operation on the assembly line of a major aerospace company for quantifying hand-arm vibrations with the objective of developing a dynamic model of the hand-arm system. The model will be used to ascertain the effect of the various risk factors on the quality of the operation. Experiment Setup A system of three tri-axial accelerometers is used to collect vibrations entering the hand-arm system and their positioning follows the ISO-5349 standard. Reaction force during the operation is measured using a force sensor. The posture of the hand-arm system is measured using two goniometers and one torsiometer. The pilot study conducted has two subjects and one pistol-grip power tool. The experiment setup and positions of various sensors is depicted in Figure 1. [ ] Analysis Method The analysis consists of transmissibility of vibrations and frequency weighted acceleration based on the recommendations of the ISO-5349 standard [1,2]. The transmissibility [3] was deduced in frequency domain after measuring data in time domain from the

Jan 6, 2006

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

By L. McWilliams, L. D. Patts, J. D. Noll, S. E. Mischler

Elemental carbon (EC) is currently used as a surrogate for diesel particulate matter (DPM) in underground mines since it can be accurately measured at low concentrations and diesels are the only source of submicrometer EC in underground mines. A disadvantage of using EC as a surrogate for DPM is that the fraction of EC in DPM is a function of various engine parameters and fuel formulations, etc. In order to evaluate how EC predicts DPM in the underground mining atmosphere, measurements of total carbon (TC; representing over 80% of the DPM) and EC were taken away from potential interferences in four underground metal/non-metal mines during actual production. In a controlled atmosphere, DPM mass, TC, and EC measurements were also collected while several different types of vehicles simulated production with and without different types of control technologies. When diesel particulate filters (DPFs) were not used, both studies showed that EC could be used to predict DPM mass or TC. The variability of the data started to increase at TC concentrations below 230, µg/m3 and was high (>+20%) at TC concentrations below 160 µg/m3, probably due to the problem with sampling organic carbon (OC) at these concentrations. It was also discovered that when certain DPFs were used, the relationship between DPM and EC changed at lower DPM concentrations.

By Albert L. Toenges

[sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we. sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we.]

Jan 1, 1938

By Albert L. Toenges

[During the past few years there has beer trend away from locomotive haulage of coal from the loading point to the preparation plant of bituminous-coal strip, miner to motorized. haulage. The question has arisen whether this is always economical, and the purposes of this investigation is to determine, if possible the economic limit for motorized haulage. The operators of strip coal mines and of open-pit ore mines have shown great interest in this problem, and it is thought that the findings of this investigation will. Provo helpful to them.]

Jan 1, 1938

This chapter presents proportionate mortality ratios (PMRs) derived from death certificate data in the National Occupational Mortality Surveillance (NOMS) database for the years 1986 through 1993. At the time this report was prepared, 1993 was the latest year for which data were available. Industry is classified under the 1980 U.S. Bureau of the Census classification system [Bureau of the Census 1982]; cause of death, under the International Classification of Diseases, Ninth Revision (ICD-9) [World Health Organization 1977]. A PMR of 100 indicates a mortality risk for a particular industry group that is similar to that for all industry groups combined. A PMR over 100 suggests a higher risk; a PMR under 100 suggests a lower risk. PMRs are subject to many factors that affect their reliability and validity and may not be comparable across populations with very different causes of death. An elevated PMR for a specified cause of death among an occupational or industry group may indicate a relationship between a work exposure and the cause of death specified. However, there are many limitations of PMRs as a measure of risk; they are most useful for generating hypotheses about exposure-disease relationships, which can then be tested in other studies. Selected PMRs are presented separately for males and females for coal mining, metal mining, nonmetallic mineral mining and quarrying (which includes nonmetal, stone, and sand and gravel), and for oil and gas extraction. All PMRs have been adjusted for age and race. In general, PMRs are presented only if the lower 95% confidence limit exceeded 100. If a PMR in an ICD-9 subcategory was above 100, however, the PMR for the larger category into which the subcategory falls is always presented and may be less than 100. PMRs can be expected to be elevated for conditions that have a high prevalence in particular occupational groups. PMRs showed elevated values for conditions known to affect miners, such as coal workers' pneumoconiosis, pneumoconiosis due to silica, tuberculosis, chronic pulmonary heart disease, and injuries. Additional findings of interest were- • An elevated PMR for myocardial infarction among male coal miners (table 2-1); • Elevated PMRs for neurologic disease in general and anterior horn cell disease, in particular among male metal miners (table 2-3); • An elevated PMR for rheumatic heart disease in male metal miners (table 2-3); • Elevated PMRs for malignant neoplasms of the digestive organs and peritoneum and for malignant neoplasms of the colon and rectum in female nonmetal miners (table 2-6); and • Elevated PMRs for non-A, non-B hepatitis and arteriosclerotic heart disease among male oil and gas workers (table 2-7).

Jan 5, 2000

By H. Leitch

In laboratory experiments, the Bureau of Mines investigated melting, quenching, and sulfuric acid leaching of alumina from mixtures of albite and anorthite, and from anorthosites containing 26 to 32 percent alumina. Variations in pouring temperature, quenching and leaching conditions, were studied with respect to the extraction of alumina and impurities. Virtually all of the alumina was dissolved by leaching melted and quenched California anorthosite in boiling 16-percent sulfuric acid solutions for 15 to 30 minutes. The leach solutions were readily separable from the solid residue by conventional thickening and filtration techniques. Only 2 to 5 grams of SiO2, Fe2O3, or CaO dissolved per 100 grams of alumina. The quantity of SiOz in solution varied inversely with the duration of the leach and with the concentration of the H2SO4 solution used. Melted and quenched Wyoming and Minnesota anorthosites with SiO2:CaO weight ratios of 4.3 and 3.2, respectively, were less amenable to sulfuric acid leaching than California anorthosite with an SiO2:CaO weight ratio of 5.3. However, excellent results were obtained on the Wyoming and Minnesota anorthosites by the addition of SiO2 to these materials before melting, in quantities sufficient to adjust the SiO2:CaO weight ratios of the furnace charges to between 4 and 6.

Jan 1, 1966

By C. W. Owings

"Coal may be and has been hauled safely at approximately the same cost with permissible2 storage-battery locomotives as with trolley, cable-reel, crab-reel, or nonpermissible storage-battery locomotives. While in general, thinking mining men readily admit the relative safety of the permissible storage-battery locomotive there are some persons who question the safety of this type; however, the greatest opposition to the widespread use of storage-battery locomotives is from those who believe them to be more expensive to operate and to be more expensive in first cost than the trolley or cable-reel locomotive. Data collected during a comprehensive study- of storage-battery and wired transmission of power in some Pennsylvania and West Virginia coal mines indicate that there is but little difference between the cost of hauling with cable-reel or with storage-battery locomotives. It would appear that if this fact were mere generally known mine operators of the more progressive type would install such equipment and avail themselves of greater safety in hauling coal.The need for greater safety in haulage in coal mines is readily understood when it is considered that during the 12 month period, July 1, 1929 to June 30, 1930, trolley or cable reel gathering locomotives caused four explosions in which 407 lives were endangered, 11 persons were injured, and 30 lives were lost. Still another disaster was averted by the vigilance of a fire boss, who discovered a stratum of gas 3 feet thick at the top of an entry into which a gathering locomotive was about to enter. Other explosions not resulting in any fatality probably have not been reported. In addition numerous fires have been caused by trolley or cable-reel locomotives, and these fires probably would have been avoided had permissible storage-battery locomotives been used."

Nov 1, 1930

By James D. Noll, M. Eileen Birch

A monitoring method for diesel particulate matter was published as Method 5040 by the National Institute for Occupational Safety and Health (NIOSH). Organic and elemental carbon are determined by the method, but elemental carbon (EC) is a better exposure measure. The US Mine Safety and Health Administration (MSHA) proposed use of NIOSH 5040 for compliance determinations in metal and nonmetal mines. MSHA also published a rule making for coalmines, but no exposure standard was provided. A standard based on particulate carbon is not considered practical because of coal dust interference. Interference may not be a problem if an appropriate size-selective sampler and EC exposure standard are employed. Sub micrometer dust concentrations found in previous surveys of nondieselized, underground coal mines were relatively low. If a large fraction of the sub micrometer dust is organic and mineral matter, sub micrometer EC concentrations would be much lower than sub micrometer mass concentrations. Laboratory and ?eld results reported here in indicate the amount of EC contributed by sub micrometer coal dust is minor. In a laboratory test, a sub micrometer EC concentration of 31µg m 3 was found when sampling are spirable coal dust concentration over three times the US compliance limit (2mg m3). Laboratory results are consistent with surveys of nondieselized coal mines, where EC results ranged from below the method limit of detection to 18µg m 3 when size-selective samplers were used to collect dust fraction shaving particle diameters below 1.5µm sub micrometer EC concentrations were ?7µg m3. In dieselized mines, sub micrometer EC concentrations are much higher.

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

By S. S. Dean, B. Silkes

"INTRODUCTION The metallurgical-research program of the Bureau of Mines .for the past 15 years has emphasized the production of high-purity nonferreus metals through the utilization of our available resources, ores, reducing agents, fuel, and power.Ore dressing or concentration, has always been a vitally important part of nonferrous metallurgy, and the Bureau continues to give most of its attention to it. In the field of the traditional nonferrous metals, the Bureau staff has developed natural-gas reduction of zinc, the application of glomerule technique to preparing high-grade lead concentrates for Scotch-hearth smelting, the production of electrolytic antimony from precious metal-bearing ores, and the recovery of nickel from nickel-chrome-iron ores.In the field of light metals, the Bureau staff has developed several improvements in both magnesium and aluminum production and in alloys of these metals. In the so-called ""rare-metal"" field, Bureau activities have included the production of pure ductile titanium on a larger scale than heretofore attempted, the electrolytic production of cobalt, chromium, and manganese which may now take their proper places as bases for nonferrous alloys as well -as ingredients of special steels. The Bureau staff has investigated many of these new alloys. Investigations of methods of recovering vanadium from its low-grade domestic ores have given promising results. Methods for the preparation of metallic zirconium have been improved."

May 1, 1947

By Robert H. Peters

The objective of the project descibed in this report was to design and field test a model health and safety program at a coal mining company and a gold mining company. The model program was implemented primarily by providing training on loss control, accident investigation, and the operation of mobile equipment; and by providing technical assistance to help solve health and safety problems. Data were obtained from company records on occupational injuries, illnesses, accidents, and "near misses"; and through direct observation of employees performing a large number of randomly selected jobs. At the coal mine, employees were observed five times over a 15-month period. At the gold mine, employees were observed six times over a 16-month period. During the study, the percentage of sampled jobs containing one or more safety deficiencies decreased from 74.3 pct to 36.6 pct at the coal mine and from 86.4 pct to 19.1 pct at the gold mine. Work on this project was performed by Woodward Associates, Inc., under a Bureau of Mines contract.

Jan 1, 1986

By J. Shawn Peterson, David S. Yantek, Adam K. Smith

Occupational noise-induced hearing loss continues to be one of the most pervasive health problems in the mining industry, despite over 25 years of regulation. One of the loudest pieces of equipment used in underground mining is the continuous mining machine. Noise sample data collected by the Mine Safety and Health Administration indicate that 42% of noise overexposures between 2000 and 2005 involved continuous mining machine operators. Previously conducted field and laboratory tests have determined that the continuous mining machine conveyor system is a dominant noise source. Loud impacts occur as the conveyor chain flight bars, used to move the mined aggregate, traverse their path from the top to the underside of the conveyor deck. Various noise control treatments have been applied to abate noise caused by the conveyor system. A durable polyurethane coating has been developed for the conveyor flight bars, resulting in a time-weighted average reduction of 3 dB(A) for an eight-hour work shift. In an attempt to further reduce continuous mining machine operator overexposures, a similar urethane coating has been applied to the tail roller component of the conveyor system. Laboratory results showed a 2 dB(A) reduction in sound power levels, but the component failed during underground durability testing. An outer steel sleeve has been added to the urethane coating of the tail roller to enhance wear resistance during mining. The urethane jacketed tail roller is the latest effort, combined with previous noise treatments, to bring the continuous mining machine into compliance with federal noise regulations.

By C. W. Owings

Available literature published or abstracted in 1953 and 1954 relating to dust prevention and suppression has been summarized and reviewed in this report, and un-published information also is included to outline current practice for those interested in dust control in and around mines, tunnels, and quarries. More and more companies are realizing the value of controlling dust by incorporating suitable methods and devices in the planning stage. In preparation and crushing plants preliminary tests have been made of the fine materials to determine the best type of dust-control equipment to use, and the details of the quantities of air, the number of sprays, the dust-allaying fluids, and the location of hoods or enclosures have been determined in advance. Such planning has paid for itself in more effective control. Similar planning in a tunnel resulted in healthful conditions and low dust concentrations.

Jan 1, 1956

By R. H. Grau, R. Krog

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. The research has demonstrated that the ventilation of large-opening mines improves significantly by including ventilation requirements in the mine planning process and implementing somepractical techniques during mining. Planning the location of long pillars to reduce the number of crosscuts between intake airways and return airways, positioning auxiliary fans in their proper locations, and establishing ventilation stoppings with minimal leakage all significantly improve the ventilation of large-opening mines. Mine operators that adopt these techniques in the mine ventilation plan will reduce mineworkers’ exposure to airborne contaminants.

By Jon A. Hummer, Emanuele Cauda, George H. Schnakenberg, Aleksandar D. Bugarski, Samuel J. Janisko, Larry D. Patts

A series of engine/dynamometer tests was conducted to assess the effects of three types of uncatalyzed diesel particulate filters (DPFs), a diesel oxidation catalytic converter (DOC) and three types of high temperature disposable filter elements (HT DFEs) on the concentrations and size distribution of diesel aerosols and concentration of nitric oxides in underground mine air. Tests were conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of these and other control technologies directly in an underground environment. The aforementioned technologies are evaluated by comparing the aerosol and gas measurements in the mine air 60 m downstream of the exhaust from a naturally aspirated, mechanically controlled engine fitted with the tested systems or muffler and operated at four steady-state engine speed and power modes. The tested DPF and HT DFE systems caused a 10-fold reduction in total mass concentrations of aerosols. The size distribution and number concentration measurements showed that all tested DPF systems and HT DFE elements effectively removed accumulation mode aerosols (D50>30 nm) for all test modes. An increase in peak number concentrations of nucleation mode (D50>30 nm) diesel aerosols is evident for some of tested DPF systems when engine was operated at high-load modes. The effects of uncatalyzed DPFs on nitric oxide (NO) and nitrogen dioxide (NO2) concentrations are found to be minor. A four-fold increase in percentages of NO2 in total nitrogen oxides (NOx) over baseline case was observed for the DOC when the engine was operated at high-load modes. The findings from this study should contribute to better understanding the potential for various control technologies to reduce exposure of underground miners to nano and ultrafine aerosols. In addition, detailed physical characterization of diesel aerosols made directly in occupational setting should foster a better understanding of the health risks associated with exposure to nano and ultrafine diesel aerosols.

By Gerald T. Homce, James C. Cawley

Arc flash generally refers to the dangerous exposure to thermal energy released by an arcing fault on an electrical power system, and in recent years, arc flash hazards have become a prominent safety issue in many industries. This problem however, has not been effectively addressed in the mining industry. MSHA data for the period 1990 through 2001 attributes 836 injuries to “non-contact electric arc burns”, making it the most common cause of electrical injury in mining. This paper presents results from several elements of a recent NIOSH study of arc flash hazards in mining, and provides information and recommendations that can help reduce these injuries. Characteristics of past arc flash injuries in mining are first outlined, such as the electrical components and work activities involved (based on MSHA data). This is followed by a review of important concepts and terminology needed to understand this hazard. Next, methods for identifying, measuring, and managing arc flash hazards on a power system are covered, with emphasis on recommendations found in NFPA 70E, Standard for Electrical Safety in the Workplace. Finally, results are presented from a detailed arc flash hazard analysis performed on a sample mine electrical power system using IEEE 1584-2004a, focusing on components and locations presenting severe hazards as well as engineering solutions for reducing the risk to personnel. Index terms – electrical arcing, electrical burns, mining, arc flash hazard analysis

By Peter W. Kauffman

This Bureau of Mines publication is designed primarily to provide mine engineers and production-level mine managers with the following: 1. Information to assist them in making the decision to retreat mine and in selecting the best retreat mining technique for specific mining conditions. 2. Information on mine planning that will enable them to design mine layouts for safe and efficient retreat mining. 3. Information that will enable them to develop a section foreman's handbook. The manual has been organized to gradually increase in level of detail as the reader progresses from beginning to end. Individuals interested in an overview of retreat mining can confine themselves to the first few chapters. Those interested in mine planning, should read the middle chapters as well. Those interested in the development of a foreman's handbook should read the entire manual.

Jan 1, 1981

By L. D. Tracy

"The first study of this subject has been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal—mining industry to standardise the forms of leases, and so avoid some of the abstruse and ambiguous clauses which may be found in many of then and the consequent liability of costly litigation.In some of the publications of the Illinois Mining Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the State have been dividedinto eight geological districts, each district being treated separately.report covers District No. VI of that classification, and it is hopedstudies of the other districts will be completed in the near future and similar results published.The report includes a short description of the geological condition the character and quality of the coal and the nature of the surface, data for which have been taken largely from the Illinois Geological Survey publications.Mining methods and percentages of recovery are mentioned, together physisal conditions, market and transportation facilities, because all of these factors have a bearing on royalties and leasing conditions."

Jan 1, 1926