Search Documents

By Brabcova Z.

This contribution deals with bubble adhesion on particle surface which consists of three steps ? the liquid film thinning, the film rupture and expansion of the three phase contact (TPC). Our attention is devoted to the third step ? to the description of the TPC expansion. Three-phase contact line expansion can be theoretically described using hydrodynamic and molecular-kinetic models. Both of these models were originally developed for the interaction of the bubble with horizontal plane in pure water. Our experiments deal mainly with the interaction of the bubble with the inclined plane in the solution of surface active agents. It was proved experimentally that molecular-kinetic model corresponds also to these conditions and this model was used for the description of the TPC expansion. The model is based on the theoretical description of the bubble contact angle on the three-phase interface. These contact angles change dramatically from 180o to equilibium (Young) contact angle close to 90o. Modificated ADSA method is used for the calculation of the contact angle. This method utilizes the Laplace equation of the capillarity; the bubble profile and the contact angle are evaluated using the set of experimental points around the edge of the bubble. The comparison of the experimental and calculated bubble profile shows a good agreement. The aim of the project is to describe the process of the TPC expansion during the adhesion of the bubble with the diameter up to 1 mm. Inclined planes were used instead of an experimental solid particle. Our experiments were provided in the solution of surface active compounds. The process of the adhesion was recorded using high-speed digital camera and images were evaluated using the image analysis software NIS-Elements. Calculations were performed using the MATLAB software. Keywords: bubble-particle interaction, adhesion, three-phase contact, contact angle

Sep 1, 2012

By L. A. Cisternas, R. I. Jeldres, C. Cruz, P. A. Robles

"Previous studies have shown that the floatability of chalcopyrite in seawater at highly alkaline conditions is significantly affected by the presence of clays. The reason is that the species of calcium and magnesium present in seawater under those conditions may act as a bridge between the surfaces of clay and chalcopyrite, generating massive aggregates that then depress. In this context, the objective of this work is to analyze the impact of pretreated seawater with low amount of calcium and magnesium ions on the recovery of a sulphide copper mineral with high kaolinite content as clay. The seawater pre-treatment is done by the addition of sodium hydroxide in a high carbon dioxide environment. The chemical reactions realized under these conditions lead to the formation and precipitation of calcium and magnesium species that are subsequently removed by vacuum filtration. The pre-treated seawater is then used in flotation tests at pH 11 for copper sulphide, where the mineral is synthetically prepared by mixtures of chalcopyrite, kaolinite, and quartz. When comparing the flotation results for different types of water, including seawater and pre-treated seawater, a significant effect is observed: as the seawater hardness decreases, which comprises the calcium and magnesium ions, the recovery of chalcopyrite is increased. However, the effect is markedly enhanced in the presence of kaolinite. Therefore, the results indicate that sodium hydroxide and carbon dioxide are able to remove different species of calcium and magnesium from seawater and could improve the chalcopyrite recovery with high kaolinite content. INTRODUCTIONIn many cases, mineral deposits are found in arid areas with little access to water resources. Water is a fundamental element to carry out the unit operations that achieved the separation of valuable minerals (especially in concentration operations). Seawater has acquired an interesting role in recent years (Cisternas and Moreno, 2014); in fact, it seems to be one of the few viable options to ensure the sustainability of the mining industry in arid zones. At present, there are numerous experiences of industries that use or have used this resource, either by submitting the seawater to a desalination treatment by reverse osmosis or by applying it directly, without desalting. The latter case may involve significant economic benefits (for example, by avoiding the investment of building a desalination plant) and in some cases some operational benefits. A positive aspect is that in general terms the foaming in the saline medium is much more efficient compared to fresh water (Quinn et al., 2014; Castro et al., 2010). Some reports show that the foaming doses required to achieve a certain quality of bubbles are remarkably reduced, reaching exceptional cases such as Xstrata's Raglan concentrator, where it did not even include foaming to carry out the operation. This fact is quite promising, considering that some researchers have stated that controlling the quality of bubbles and foam could float minerals through coarse particles. This would lead to multiple benefits, such as energy savings by avoiding excessive grinding and a lower presence of fine ore that causes major problems in water recovery operations by gravitation (such as thickening) and in tailings management. However, seawater also causes significant challenges in multiple operations (Jeldres et al., 2017, 2016; Castro et al., 2010), as for example in minerals with high clay content (Uribe et al., 2017). In fresh water, the presence of clays minerals in ores is already a major problem in the flotation stages since the operation becomes difficult to be controlled, and operators are commonly forced to increase the consumption of reagents because the collectors are deposited on the clays' surfaces reducing froth stability (Farrokhpay and Bradshaw, 2012). Sometimes the use of rheology-modifying reagents should also be incorporated since the pulps become more visc"

Jan 1, 2018

By W. H. Yong

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores, whereas oxidized molybdenum ores have not been exploited and utilized efficiently. The aim of this article is to study the applied mineralogy of an intergrown iron-molybdenum oxidized ore in order to provide a mineralogical basis for the ore beneficiation research. The ore occurred in a surface oxidized zone seam and contained 23.65% Fe2O3 and 1.58% Mo. Various characterization techniques were employed to study the chemical composition and mineral composition of the ore, the particle size distribution of the minerals in the ore, and the tex-ture and structure of the ore. The results showed that the iron-molybdenum ore occurred in a wet, soft and earthy state. The ore was composed mainly of several oxidized minerals and colloidal min-erals, including wulfenite, barite, limonite and quartz. Wulfenite was one of the major and stable components in the ore and occurred as a separate mineral. Wulfenite, barite and quartz were granu-lar minerals with particle size ranging from fine to coarse but mainly in the fine particle range. Li-monite showed a crust and honeycomb-like colloidal state and composed the framework in the ore for the formation of the other minerals. They filled the pores in the framework and the size of the pores affected the size of the minerals formed in the pores and hence the recovery of wulfenite in ore beneficiation. According to the applied mineralogical properties of the oxidized molybdenum ore, a promising ore beneficiation process was proposed as follow Magnetic separation should be carried out first to separate the magnetic iron minerals and then the molybdenum mineral will be recovered by gravity concentration or a combination process of gravity concentration and flotation, depending on the distribution of the molybdenum mineral in the product of the magnetic separation.

Jan 1, 2014

By Francisca San Martín, Martin Rudolph, Willy Kracht, Tomás Vargas

It has been shown that bacteria Acidithiobacillus ferrooxidans can be used to depress pyrite in seawater flotation at natural pH, which opens the possibility for its use as an alternative to lime to depress pyrite in copper sulfide flotation. In order to have a better understanding of the mechanisms involved in pyrite depression with A. ferrooxidans, an exploratory experimental campaign was carried out, including attachment density and contact angle measurements, and the effect of adding bacteria before or after collector. Biodepression of pyrite improves when increasing pH from 3 to 8, with a decrease in recovery from 92% to 36%. This increase in depressing capability is accompanied by an increase in attachment density, from 2.58×108 bacteria/g to 1.99×109 bacteria/g at pH 3 and 8, respectively, suggesting that the mechanism of depression is related to the attachment of bacteria to the pyrite surface. It was observed that the conditioning sequence with collector and bacteria influences the biodepression capacity of A. ferrooxidans. Having as a reference a value of pyrite recovery equal to 97%, when using only xanthate in seawater flotation at pH 8, the effect of both conditioning with bacteria-followed-by-xanthate and xanthate-followed-by-bacteria were assessed. When bacteria were added before the collector, the recovery of pyrite decreased to 36%. On the other hand, when bacteria were added after collector, the recovery was 64%, showing that biodepression of pyrite with Acidithiobacillus ferrooxidans is more efficient when the conditioning is carried out first with bacteria. The contact angle values show that there is little effect of the second component added to the system, i.e., if pyrite is first conditioned with bacteria, the contact angle does not change significantly once the xanthate is added (bacteria-followed-by-xanthate). The same was observed when the conditioning sequence was xanthate-followed-by-bacteria.

Jan 1, 2018

By Jonas Addai-Mensah

In this paper, the results emerging from the several basic and applied studies performed to provide fundamental understanding of the interplay between clay pulp chemistry, orthokinetic flocculation performance, particle interactions, applied shear and dewaterability of fine clay mineral dispersions are presented, reconciled, and discussed. Modification of pulp chemistry and behaviour was achieved by using kaolinite and Na-exchanged (swelling) smectite clay minerals, divalent metal ions (Ca(II), Mn(II)) as coagulants and high molecular weight, anionic polyacrylamide copolymers: carboxylate substituted (PAM A) and 2-amido 2-methyl propane sulphonate (PAM S) (PAM S), non-ionic polyacrylamide homopolymer (PAM N) and non-conventional, non-ionic polyethylene oxide (PEO) as flocculants. Clear links between pulp interfacial chemistry, particle interactions and dewatering behaviour, resulting from the influence of hydrolyzable metal ion, pH, temperature, polymer structure type and shear, are established. Optimum conditions for improved, orthokinetic flocculation performance of negatively charged clay particles, reflecting faster settling flocs (>10 m/h) comprised: (i) coagulation, (ii) moderate agitation rate, (iii) shorter agitation time and (iv) anionic rather than non-ionic PAM. The optimum flocculation conditions did not, however, have a significant impact on the final sediment solid content of 20 ? 25 wt%. Further application of shear to pre-sedimented pulps improved consolidation by 5 - 15 wt % solid. Application of the findings and new knowledge gained to real plant tails? case studies for marked improvement in dewaterability through thickening is demonstrated.

Sep 1, 2012

By S. Jagdish

India ranks fourth in the world of iron ore production and exported 55% of the total iron ore production of 180.9 million tons in 2006-07. As per United Nations Framework Classification (UNFC), the total iron ore reserves in India is 25249 mt. This consists of about 14630 mt of Hematite ore and 10619 mt of Magnetite ore. While the deposits of magnetite iron ore are limited to the states of Karnataka, Andhra Pradesh and Tamil Nadu, hematite ore is available in abundance in Jharkhand, Orissa, Chhattisgarh, Karnataka and Goa. National Steel Policy, declared by government of India in 2005 envisages 110 million tons of steel production by 2020. This is likely to be revised upwards. Massive exploration work in iron ore is needed to convert the available resources of iron ore into reserve category. Steel Authority of India Limited (SAIL) produced more than 24.5 million tons of iron ore during 2006-07 and plans to produce 42.0 million tons per year by the year 2010-11 to meet the requirement for a hot metal production of 26.2 million tons. While processing iron ore, the challenge faced would be the reduction of the gangue materials ? alumina and silica. It is proposed to bring down alumina and silica in the iron ore to less than 2% each from the current level of 2.5%~3.5% each. Appropriate beneficiation schemes are being developed depending upon the mineralogical characteristics of iron ores at different mines in the country. The state-of-art beneficiation technologies like Hydro-cyclone, jigging, magnetic separation etc. will be incorporated. SAIL?s corporate plan envisages blast furnace burden of 15% iron ore lumps, 15% pellets and 70% sinter by 2010. This strategy opens up the opportunity of utilization of micro fines generated in the mining and beneficiation processes for pellet making. This also directs towards all together new technological approach to the beneficiation process. SAIL is planning to set-up three pelletisation plants of 2~3 mtpa capacity. Environmental issues like reduction in slime loss and utilization of dumped low-grade iron ore are very important. R&D Centre for Iron and Steel, SAIL has carried out extensive laboratory investigations in the above area. This will help in reducing the loss of valuable iron through slimes and also increase the iron ore resource base. Laboratory investigations indicate that low grade dumped ore fines with Fe: 55.5% can be upgraded to a product with Fe: 66.2% with about 48% recovery.

Jan 1, 2014

This investigation addressed two products from Samarco?s desliming circuit, namely underflow of cleaning cyclones and underflow of desliming cyclones. The roughing cyclones receive the product of the grinding circuit. The underflow of the roughing cyclones feeds the cleaning cyclones and the overflow feeds the desliming cyclones. The underflows of cleaning and roughing cyclones are combined to constitute the feed of the flotation circuit. These fractions were characterized and a new process route was proposed. The size distributions of the two fractions are quite different. The desliming cyclones underflow presents higher amount of material passing 37 µm and of ultrafines as compared with the cleaning cyclones underflow. Laboratory scale flotation tests were performed in a mechanical machine aiming at comparing the performances of these products in the presence of the reagents employed in the concentrator. Pi-lot scale column flotation yielded enhanced iron recoveries for both products in comparison with those achieved in laboratory mechanical cells, without impairing the concentrate quality. The in-crease in recovery was more significant in the case of the cleaning cyclones underflow. These results suggest the use of columns in the flotation of this product aiming at increasing the overall iron recovery. Nevertheless the results also showed that the use of columns to float the cleaning cyclones underflow should also be taken into consideration. Despite the fact that this product requires a longer residence time in order that the required silica content in the concentrate is achieved, the indication is that higher levels of iron recoveries might be reached. The conclusion is that, due to the different behaviors of the two products, they should be processed in distinct circuits to maximize the iron recovery.

Jan 1, 2014

Large quantities of electrical and electronic equipments are discarded at the end-of-life (EOL) in different industries and house hold applications. Their disposal is creating a challenging environmental problem due to the presence of hazardous metals and non-metallic materials such as epoxy resins and plastics including brominated flame retardants etc particularly in printed circuit boards (PCBs). The recovery valuable metals and separation of hazardous materials from discarded PCBs will not only conserve the resources but also mitigate the environmental pollution. From a recycling point of view for a sustainable society, the studies have been carried out for the recovery of metal values from EOL-PCBs of DVD video players (DVD-PCBs) and vacuum cleaners (VC-PCBs) using physical beneficiation techniques. The concentration of the metals was found to be 43 wt.% and 30 wt.% in DVD-PCBs and VC-PCBs, respectively. Both the PCBs samples were ground in a hammer mill after cutting and their size analysis was carried out. The liberation of the metallic and non-metallic fractions was investigated under the microscope for different size fractions. Subsequently, froth flotation and pneumatic air separation studied were carried out to enrich the metallic constituents. The studies showed the enrichment of metals in coarser particles (-1000 +150 µm) and non-metals in the finer particles -150 µm following mechanical recycling process. A grade of 90 % with 75% recovery was achieved by froth flotation, but lower grade and recovery of 75% and 65% respectively were obtained by pneumatic separation with -1500 µm powders for DVD-PCBs. A grade of 86% metal was obtained by froth flotation with 76% recovery in the case of VC-PCBs. The lower grade of 65% with almost same recovery was achieved during pneumatic separation studies due to lower concentration of metals in VC-PCBs. The studies also showed that the froth flotation is an efficient process for enrichment of metals from both the samples. The process is environmental friendly as no chemicals are employed during entire processing. The higher recovery and grade of metal is expected to be obtained on a large scale beneficiation process.

Sep 1, 2012

By V. V. Lodeischikov

This paper covers some problems of treatment of complex gold ores and concentrates containing copper, lead, zinc, antimony and uranium. All these metals may present in ores both as major and associated components. The paper suggests recommendations for early determination of relative value of the metals in ores, which largely contribute to the selection of concentration and metallurgical flow sheets. The focus of this work is on treatment of complex ores in gold plants. The metal extraction technologies used by such gold plants are typically aimed at maximum gold recovery. Therefore, production of base metals as by-products requires significant updating of the existing process flow sheets based on economic, environmental and other considerations. At the same time, cooperation between gold plants and base-metal plants is of great importance. This paper provides an overview of worldwide existing and innovative processes of base metals extraction from complex and refractory gold ores.

Jan 1, 2014

By C. Dorfling

Experimental work was performed using a bench scale autoclave to evaluate the effects that leaching temperature, pressure, initial acid concentration, and the solid to liquid ratio have on the behaviour of base metals and platinum group metals in a high-pressure sulphuric acid oxygen leaching system. The concentrations of metals in the leach solution were measured over time at different leaching conditions. At the conditions investigated, the initial acid concentration had the largest influence on the copper leaching kinetics, while the leaching rates of the other precious metals (OPMs: rhodium, ruthenium, and iridium) were highly dependent on the leaching temperature. A set of chemical reactions that can be used to describe the leaching chemistry was proposed, and the associated reaction kinetics were quantified. As a first estimation, the rate expressions were considered first order, and the rate constants were determined using the method of least squares, considering the experimental and predicted concentrations obtained for the different leaching conditions. Of the OPM compounds, the sulphides showed the fastest dissolution rate, followed by OPM alloys, and finally the OPM oxides. During the initial leaching stages, base metals and OPMs competed for the available dissolved oxygen, with oxygen being preferentially used for copper leaching. Precipitation of OPMs during the initial leaching stages can be ascribed to copper and nickel dissolution according to exchange reactions between dissolved OPMs and copper present as digenite or nickel present as polydymite. Control of the autoclave residence time is of particular importance to enhance the selectivity of this leaching step, given the dependence of the PGM leaching rates on the extent of copper dissolution.

Sep 1, 2012

By K. Amano, K. Haga, Y. Watanabe, A. Shibayama, A. Batnasan, A. Battsengel

"Apatite is an important host mineral in igneous and metamorphic rocks for production of phosphate fertilizers and phosphoric acid, and a potential source of rare earth elements (REE) production. For dissolution of REEs, sulfuric acid is better leaching reagent to develop the economical viable process for recovering of rare earth elements from apatite ore. However, the efficiency of rare earth elements dissolution in H2SO4 is about 30 % due to the formation of calcium phosphate or calcium sulfate as precipitate. On the other hands, phosphorus is mainly produced from phosphate ore. However, when treating rare earth elements containing phosphate ore, rare earth elements were discharged. Hence, development of novel apatite ore treatment process is required for effective utilization of natural resources. In this study, apatite deposit associated with REE was treated with sulfuric acid leaching and two stage precipitation by oxalic acid (C2H2O4) and magnesium chloride (MgCl2) for recovering REE and phosphorus, individually. Results showed that it can be seen the vast majority of La (87.5%), Ce (87.3 %), Pr (86.1 %), Nd (85.2 %) and Y (90.9 %) were dissolved in 1 mol/L diluted H2SO4 solution from the apatite ore. As average leaching rate of REE, over 85% of REE were leached by the condition. In the first stage precipitation using the obtained pregnant leach solution from leaching, over 90% of REE was precipitated by oxalic acid addition after controlling pH to 1 by NH4OH solution. After pH changed to 8.5, over 90% of phosphorus was recovered as precipitate by magnesium chloride addition in second stage precipitation"

Jan 1, 2018

By X. Q. Cui

The surficial collapse pits of the mining areas are continuously spreading in Beiminghe iron mine of Hebei Province as a result of the exploitation, which has done a lot of damage to the circumjacent ecological environment of the mine. It is a new path to handle the mine tailings at the present time that the thickened tailings are used to backfill the collapse pits, in which way the problems of the surficial collapse and the nowhere discharge of the tailings are both solved, and the rational utilization of the mine tailings and the clean production of the mine enterprise are realized. The?200 mesh content of the tailings of Beiminghe iron mine is 76.87%, and?325 mesh content is 63.50%. Semi-industrial dehydration experiments to the tailings have been done using the hydro-cyclone classified thickening process. The results show that when FX125 hydrocyclone is adopted, the concentration of underflow can achieve 73.31%, and the yield ratio is 61.78%; when FX150 hydrocyclone is adopted, the concentration of underflow is 70.57%, and the yield ratio is 54.31%, which indicate that the minor diameter hydrocyclone is propitious to improve the yield ratio of the underflow. The semi-industrial dehydration system of hydrocyclone classified thickening process is com-posed of FX125 hydrocyclone, D3600 high-efficient thickener and D2000 thickening bucket. The capacity to tailings disposal can achieve 3.07t/h and the tailings can be thickened from 28.86% to 62.45%. Compared with the traditional thickening-filtrating process and the total tailings directly filtrating process, the hydrocyclone classified thickening process has the merits of simple flow and high thickening efficiency, so it is easy to be realized in the mine.

Jan 1, 2014

By X. J. Lu

Purified Na-montmorillonite samples were used as the starting materials to prepare organically modified montmorillonites (OM), and a series of OM samples were prepared by intercalation of al-kyl quaternary ammoniums with different alkyl chain length. The interlayer spacing (d001) of the OM was determined by small angle X-ray diffraction and its gelating performance was characterized by measuring the viscosity of OM/dimethylbenzene mixture. The effects of alkyl chain length, dosage of alkyl ammonium, intercalation duration and layer charge of the starting material on the OM structure and gelating properties were investigated. According to the results, the adsorption quantity of the alkyl ammonium is dependent on the hydrocarbon chain length, the dosage of the alkyl ammonium and the retention time. The adsorption quantity of the alkyl ammonium increases with the chain length and the dosage, and extra adsorption more than the CEC of the montmorillonite sample was observed under the dosages of more than 1.3 CEC. The interlayer spacing (d001) of the OM shows a dynamic variation with the dosage and the retention time, and super interlayer spacings greater than the length of the alkyl ammonium were observed under larger dosages and shorter retention times. However, the gelating performance of OM does not follow the variations of the adsorption quantity of alkyl ammonium, an optimum viscosity value of OM/ dimethylbenzene gel was observed with the moderate adsorption of the alkyl ammoniums. Furthermore, the layer charge plays an important role on the gelating performance of OM. The OM synthesized by the starting material with lower layer charge shows better gelating performance in the dimethylbenzene solution.

Jan 1, 2014

Micro-fine disseminated molybdenite was ground in a laboratory stirred mill using steel media and zirconium media respectively. The floatability of ground molybdenite and slurry chemistry was investigated. It was found that the total recovery of ground molybdenite using zirconium media was higher while the pH and Eh of the slurry are lower than that using steel media. When steel media was used, iron oxy-hydroxides had been generated coated on the surface of molybdenite, and decreased the floatability of molybdenite, especially of the -10µm particles. The iron and lead oxy-hydroxides was generated by the reaction between steel media with pyrite and galena associated with molybdenite. It was also found that changing the grinding media to inert can benefit the flotation of molybdenite. Keywords: stirred mill, grinding environment, floatability, micro-fine disseminated molybdenite, fine grinding

Sep 1, 2012

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling."

Jan 1, 2003

By Dingwu Feng, Jannie S. J. van Devente

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated in two slurry systems, i.e. gold cyanidation and geopolymerisation. The kinetics of gold extraction were significantly enhanced and the cyanide consumption was reduced in the cyanidation of a pyrite concentrate using ultrasonication, probably due to the prevention of leaching passivation, the improvement of the dissolution of the gold host sulphides and the oxidation of soluble sulphides to sulphate. The effectiveness for ultrasonication was improved with the injection of oxygen and the addition of dithiophosphate through enhancing the formation of the oxidation radicals and selectively inducing cavitation bubbles directly at the sulphide interfaces. Ultrasonically enhanced cyanidation could render currently uneconomic deposits viable for extraction by improved cavitation efficiency with the aid of surfactants.Ultrasonication increased the compressive strength of the formed geopolymers through accelerating the dissolution of the Al-Si materials, strengthening the bonds at the solid particle/gel phase interfaces, enhancing the polycondensation process and improving the formation of semi-crystalline to crystalline phases. The use of power ultrasound will yield high-performance geopolymer materials."

Jan 1, 2003

By Liu Jin

"In order to reduce the dosage costs and increase the economic benefits of a full floating process in a low grade complex multi-metals W-Mo ore, based on the study of the magnetic characteristics of the main gangue minerals, a joint process by magnetic separation and floatation technology is adopted. The first step of the flowsheet is to recover magnetite by magnetic separation, then remove the magnetic gangues by high gradient magnetic separation (HGMS) and finally recycle the W-Mo from the magnetically separated tailings by flotation. Results of the lab experiment show that in comparison with the full flotation process, the floatation feed tonnage of the combined flowsheet are only 46%. The grade and the recovery of Mo in the rough Mo-Bi concentrate is similar with the original one while the WO3 in the tungsten rough concentrate is increased from 3.85% to 6.64%. The dosage costs are reduced by 53%. The new process can significantly improve the plant economically. INTRODUCTION With the continuous exploitation of scheelite resources, the easily obtained resource is gradually depleting. The ""lean, fine and complex"" scheelite resource has become the main research object of tungsten beneficiation (Lou et al., 2010) (Xiao et al., 2013). The passive situation of tungsten beneficiation can be reversed by enhancing technological innovation and investment in science and technology, changing the business philosophy and mode of production, optimizing the process structure and process conditions, improving various technical indexes and reducing production costs of reagents, which will maximize economic benefits (Jiang et al., 2012 ) (Zhu et al., 2016). A polymetallic deposit of tungsten molybdenum bismuth original process adopts a full flotation process. With the expansion of stope mining, the content of valuable metals in the ore continues to decrease, resulting in a high cost per ton of concentrate produced and a low output value (Li et al., 2015)."

Jan 1, 2018

By Vinay Jain, Dharmendr Kumar, Beena Rai, Venugopal Tammishetti

"Selective dispersion-flocculation is considered to be an effective process for the beneficiation of ultrafine particles. This process is based on the preferential adsorption of a flocculant on the mineral particles to be flocculated, leaving rest of the mineral suspended. It has been successfully implemented at plant scales for the beneficiation of ultrafine particles of iron ores, for which conventional methods such as gravity separation, magnetic separation and flotation do not work efficiently. However, the key element responsible for the success of any selective flocculation process is the appropriate choice of the flocculant used for achieving the desired selectivity. At our lab, we are working on design and development of such selective reagents for mineral processing applications, including the beneficiation of iron ore slimes, using a combined molecular modeling and experimental approach. In this study we have employed density functional theory (DFT) to calculate the interaction energies and explain the interaction mechanisms of chitosan with the main minerals present in iron ore slimes, namely, hematite [a-Fe2O3], goethite [a-FeO(OH)], gibbsite [a-Al(OH)3] and kaolinite [Al2Si2O5(OH)4]. The magnitudes of the computed interaction energies follow the trend: Hematite > Goethite > Gibbsite ~ Kaolinite Al-OH terminated > Kaolinite Si-O terminated Analysis of the optimized geometries and electronic structures reveals that the O & N atoms of chitosan molecule form coordinate bonds with surface Fe-atoms of hematite while only weak hydrogen bonds are formed in the case of goethite, gibbsite and kaolinite surfaces thus explaining reasons behind the stronger interactions with the hematite surface. The theoretical findings were validated by performing selective flocculation experiments using chitosan as a flocculant. The selective flocculation experimental results show that a final concentrate of ~60% Fe can be obtained from a feed containing 53.13% Fe with Fe recovery of 74%. The mineral estimation in the obtained concentrate indicated that hematite and goethite are recovered in concentrate while gibbsite and kaolinite are rejected in the tails. These observations were consistent with our theoretical findings. Our work highlights the promising role molecular modeling techniques such as DFT can play in the design and development of selective reagents for beneficiation of alumina-rich iron ore slimes."

Jan 1, 2018

By Z. H. Li

In connection with the features of characteristic waste water (containing cyanogen, arsenic and heavy metal) pollutants discharged by gold industry as well as the environmental features at the location of gold production enterprises, this paper briefly described the traditional method of treatment, and focused on the argument for technologies of clean production, advanced treatment and process control technology. Moreover, it clarified the future policies and development trend for treatment on characteristic waste water from gold industry.

Jan 1, 2014

"A sulfide ore containing 2.19 g/t Au and 13.13 g/t Ag was studied for the deportment and extractive metallurgy of pay metals. The ore is composed mainly of non-sulfide minerals with approximately 10% pyrite and minor amounts of marcasite, chalcopyrite, galena, sphalerite, and arsenopyrite. The deportment study using a comprehensive approach showed that gold and silver minerals in the ore are mainly native gold (Au), electrum (Ag, Au), petzite (Ag3AuTe2), hessite (Ag2Te) and volynskite (AgBiTe2) with minor amounts of acanthite (Ag2S) and argyrodite (Ag8GeS6). At current grinding fineness (P70@150µm), the majority of liberated native gold and electrum particles are larger than 20µm with 85% >40µm, some of them are even larger than 150µm, indicating that extended leach time may be required to dissolve these coarse gold grains to completion and gravity concentration needs to be considered. Petzite is relatively fine with all liberated particles being less than 80µm in size. Gold distribution and leach testwork results showed that liberated gold accounts for 50% of the head assay, exposed gold associated with sulfide and non-sulfide minerals accounts for 30% and 11% of the head assay, respectively. Gold locked in sulfide and non-sulfide accounts for 4.8% and 4.1%, respectively. Thus, it is recommended that cyanide leaching be considered for extracting gold in this ore. This paper presents the detailed results of the gold and silver deportment study and extractive metallurgy testwork, and discusses the impact on process selection and flowsheet development.INTRODUCTION Gold and silver have been found in various geological environments and ore types. In terms of the gold deportment and extractability, gold ores can be classified into two categories and 12 types. Their extractive metallurgy is largely driven by mineralogical factors such as particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide and sulfarsenide mineral structures (Zhou et al., 2004; Marsden & House, 2006; Zhou, 2013a, 2013b). Compared to gold, silver mineralogy is more complex and metal extraction is more challenging due to its presence in over 200 Ag-bearing minerals (a silver-rich ore body would typically contain 5 to 10 different silver minerals) (Gasparrini, 1984), presence of refractory silver minerals (such as pyrargyrite, prustite and stephanite) and submicroscopic silver in sulphide minerals (such as galena and copper minerals) (Chryssoulis et al., 1985; Di Prisco et al., 2002). The presence of these issues often causes problems in Ag-bearing ore processing. Therefore, knowing the deportment of gold and silver in the ores and metallurgical products is important for flowsheet development and process optimization."

Jan 1, 2018