Search Documents

By John Ralston, Jona Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By Carolina Achiardi, Álvaro Videla

"In pre-design a flotation plant copper sulphide is useful to apply a simplified methodology of economic analysis that relates the size of the grinding product (P80) with the throughput and their effect on copper grade and recovery of copper in the final concentrate of a flotation circuit. With this objective, this methodology covers the following analysis, perform by evaluation of five sizes grinding products (P80): 120, 150, 180, 210 and 240 microns. • Flotation testwork (rougher kinetic, open and closed cycle test) has been done to determinate the optimum operating conditions and to estimate the maximum recovery of copper in the concentrate, using Klimpell model • Flotation plant design assumes a conminution product obtained from a 25,000 HP ball mill • Metallurgical balance is performed for the circuit based on flotation testwork • Economic evaluation by calculating capital expenditure (CAPEX), operating expenditure (OPEX) and sales revenue, to determine NPV is performed and relates to the NPV. An optimum grind size is then obtained based on cash flow. The results shows a grinding product size that optimizes flotation and allows a higher NPV and INPV over other alternatives."

Jan 1, 2014

Separation performance of a Floatex Density Separator (FDS) has been studied both experimentally and theoretically. Experimental results reveal that at a lower bed pressure the FDS acts like a classifier. Higher bed pressure is required to attain the concentration effect as proper development of suspension density occurs under these conditions. It is seen that the size or density alone is not able to describe the partition fully. The terminal settling velocity, which includes both the size as well as the density of the particle can be a useful descriptor of separation in a FDS. While a narrowly distributed feed offers better performance of a FDS, a wide size distribution of feed results in large scatter in the terminal settling velocity distribution and renders the separation difficult. The closely sized feed enhances the density effect in concentration. A higher teeter water flow rate also helps in carrying larger-lighter particles to the overflow by increasing the cut off terminal settling velocity as it increases the net upward force. A detailed description of separation performance in a Floatex Density Separator has also been established from theoretical considerations. Separation performance of the separator is described using a simple slip velocity model. The model has been validated com-paring the predicted FDS performance results with those experimentally measured under widely different operating conditions.

Jan 1, 2014

By Wei Sun, Chengwei Li, Zhiyong Gao, Yuehua Hu

"Grinding for mineral liberation is a prerequisite for a successful flotation separation. Different grinding media produce mineral particles with different morphologies and surface properties. In this study, the surface physicochemical properties of fluorite particles produced by ball and rod mills were systematically investigated through single mineral flotation experiment, wettability measurement, X-ray diffraction (XRD) test and scanning electron microscopy (SEM) observations. The XRD observations reveal that the surface exposure degree for both mill particles follows the order {111} > {110} > {100}. The difference lies in that the rod mill ones have a higher exposure of more reactive {110} and {100} surfaces, leading to a stronger interaction with the collector. The difference also leads to their higher elongation and lower roundness values of rod mill particles which are beneficial for the particle-bubble attachment by shorting the induction time. The wettability and flotation results show that the rod mill ones have a lower critical surface tension and a greater hydrophobicity when treated with the collector solution and accordingly perform a higher flotation recovery. This work, for the first time, revealed the importance of the exposure of crystal surfaces in determine the shape factors and reactivity of the mineral particles and will help provide guidance for optimizing flotation separation and particle surface modification. INTRODUCTIONFluorite (CaF2) is the most important source mineral for producing F-based chemicals and materials which are widely used in industrial, environmental, and medical fields [1, 2]. In ore deposit, there are two kinds of occurrence forms of fluorite mineral. Firstly, the fluorite mainly coexisted with the gangue minerals like calcite (CaCO3) and quartz (SiO2). Because of their similar density and fine-grained dissemination in ore deposit, ball mill grinding before flotation separation has been widely applied to produce relatively fine particles [3]. Secondly, the fluorite is often associated with other valuable minerals with higher relative density such as scheelite (CaWO4) and cassiterite (SnO2). Due to their obvious density differences and coarsely grained distribution in ore deposit, rod mill grinding before gravity separation has been usually used to produce more uniform particles and avoid over-grinding [4-6]. After the gravity separation, a flotation separation is also employed to beneficiate the fluorite [7]."

Jan 1, 2018

By Katarina Theander, Robert J. Pugh

The generation of froth with a critical degree of stability and height is an important aspect of the froth flotation. In this paper we have studied the synergism and anti-synergism in frothing behaviour in a mixed flotation collector/frother mixture (a model fatty acid; sodium oleate and a model frother; nonionic (polyethyleneoxide alkyl C14E6). Values of the collector / frother molecular interaction parameters (the ß-parameters) were determined from the surface tension data using regular solution theory. The frothing characteristics of the system were evaluated using a glass column equipped with a series of conductivity electrodes, which enabled the water content of the froth to be determined. From these measurements, the dynamic frothability and static froth stability were determined. It was concluded that the synergism/anti-synergism in frothability was depended on the molecular composition of the surfactant system, the diffusion of monomer to the thin film interface and on the breakdown of the mixed nonionic/anionic micelles.

Jan 1, 2003

By Fiona Sofra, Briony C. Ruse, David B. Boger

"The sustainability of the mining industry must be addressed through improving tailings management. The use of thickened tailings and pastes stems from a paradigm shift towards designing tailings disposal sites to suit their surrounding environment, rather than manipulating the environment to accommodate the tailings. Thickened tailings and pastes usually exhibit non-Newtonian behaviour, so a thorough understanding of the rheological characteristics of the material is required in order to determine the disposal plant operating conditions.Full Cost Accounting techniques may be used to provide financial justification for the implementation of alternative tailings disposal techniques through the calculation of a disposal cost per tonne of tailings over the life of the facility. Improved disposal methods such as thickened tailings disposal involve additional initial capital expenditure but reduce environmental impacts. The cost savings associated with environmental impact mitigation are reflected in Full Cost Accounting outcomes.Rheological characterisation is significant as a design basis that may be analysed using Full Cost Accounting to justify the initial capital expenditure of dry disposal systems for improved environmental performance."

Jan 1, 2003

By Y. M. Zhao

Reutilization of waste printed circuit boards (PCB) can not only prevent potential environmental pollution, but also achieve recycling of secondary resources. Study on recycling of discarded PCB belongs to the front edge of environmental pollution prevention and resource recycling. In order to effectively crushing waste PCB, and solve the problem of secondary pollution of fugitive odor and dust during the crushing process, a wet impacting crusher was adopted to achieve comminution liberation of PCB in water medium. 96.79% of the crushed yield was distributed in ?2mm, and metal took 97.18% in this grade of production. Size distribution of PCB particles was characterized double peaks at the sizes of ?1+0.5mm and ?0.074mm. A double Rosin-Rammler function, is called DRR function, is put forward to describe the size distribution of PCB particles. The DRR function of cumulative weight percentage oversize of PCB was non-liner fitted by self-defining DRR function of the Origin 7.0. The evaluation indexes of the fitting results are the correlation coefficients R2 of 0.9994 and residual E of 0.18671, those show that DRR function is perfectly accurate. Based on the research the mechanical separation and material properties of PCB, a wet process of reclaiming metals from PCB using a new style separator ? tapered diameter separation bed (TDSB) in water medium was designed, and the related separation mechanism was studied. The fluid field of the tapered diameter separation equipment was simulated by the Ansys Flotran software, the variation laws of the velocity in each position in the fluid field as well as the equation of axial distribution sectional max velocity were analysed according to the simulation result, the stress change and motion trajectory of the pellet in the certain fluid field were analysed. The results show that the expanding tubular structure of the varied diameter separation bed indicates gradually decreasing velocity of water flow along the axis, assuming a certain angle in the bed, as a result of the gravity?s influence, and there was corresponding change to the distribution of the flow velocity, thus the whole formed a special fluid field where velocity variations exist in different positions. When the material passed through the fluid field along with the water flow, as a result of the difference to the particle density, the granularity and the shape, there would appear the difference to the motion trajectory as well as the movement distance under the action of the fluid: The lower density materials discharge along with water flow, but the higher density materials would be kept in bottom of the bed and discharge through material mouth. Therefore, light and heavy products were separated effectively according to the density. Using tapered diameter separation bed to process the ?1mm size crushed material of waste printed circuit boards, with the discharge of water 5.5m3/h, feed-rate of the material 250g/min and with an obliquity 35°, product with 93.92% in integration efficiency and 93.73% in recovery ratio of the metal were obtained by the primary separation. Compared with other mechanical methods, the range of particle size was broaden using the TDSB to recovery metals from PCB, and lower limit size of separation almost approach to 0. An innovative process of ?wet impact crushing+ classifying+ tapered diameter separation? recycling metals from waste PCB was developed.

Jan 1, 2014

By L. Semushkina

Next generation flotation agents of KSK series for the concentration of complex copper-lead ores and the new ferromagnetic nanosized depressor of galena are introduced in this work. The feature of the KSK flotation agents is that they exhibit both frother and collector properties. KSK-6 can successfully substitute the widely used in Kazakhstani industry reagent ?-80 at the reduced consumption of butyl xanthate by 30 %. The new ferromagnetic nanosized depressor of galena, besides a low consumption rate of 100 g/t, also makes possible to exclude sodium sulfite (3-4 kg/t) and ferrous sulfate (5-6 kg/t) from the separation process, and receive high metal grade concentrates. Keywords: complex copper-lead ore, flotation agent, concentration method, ferromagnetic nanosized depressor

Sep 1, 2012

By Kevin Davey, Liza Forbes, Leanne Smith

Given the global scarcity and value of potable water, interest in the use of water of lower quality in mineral processing has grown significantly in recent years. Previous laboratory batch flotation tests conducted at CSIRO have shown that chalcopyrite floats strongly without collector in distilled water and that the collectorless flotability of chalcopyrite is unaffected by the use of brackish water, sea water or hypersaline water. In contrast, bornite is moderately flotable without collector in distilled water but all three lower-quality waters have a detrimental effect on the recovery of bornite. The depressant effect is so strong that the little recovery achieved in these waters was only slightly above what might have been expected from entrainment alone. This work has now been extended to another important copper sulfide mineral, chalcocite. In contrast to chalcopyrite and bornite, chalcocite does not exhibit collectorless flotability so the chalcocite tests in this study were performed in the presence of a standard collector (potassium ethyl xanthate). The results reveal that chalcocite is flotable with xanthate in distilled water but the lower-quality waters have a detrimental effect on the recovery of chalcocite. This effect is partly reversed by increase collector additions. Further tests were completed in order to investigate the effect of the different ions present in the saline waters on chalcocite flotation. Possible reasons for the observed differences are discussed in terms of the pulp chemistry of the system.

Jan 1, 2014

By C. Hazotte, M. -O. Simonnot, V. Houzelot, B. Laubie, M. Guilpain, B. Jally

"More than 400 plants in the world are able to accumulate nickel (Ni) in their aerial parts at concentrations higher than 10 g per kg of dry biomass. Then, Ni can be recovered from the biomass of these hyperaccumulator plants. Agromining is a chain consisting in growing such plants and producing metal. It has been developed thanks to the combined know-how of agronomy and hydrometallurgy. Hydrometallurgical processes have been designed; two different pathways were developed: i) acid leaching of ashes after biomass combustion and ii) direct Ni water extraction after biomass grinding. Experiments with 2 species of Ni hyperaccumulators (A. murale from the Balkans and R. bengalensis from Malaysia) have shown that the first process is very robust and transposable. For the second one, the way Ni is stored in the plant has a strong influence on extraction. A. murale transformation was explored in more details from the lab scale to the pilot scale. Results proved that Ni is totally transferred into the aqueous phase after 2 hours at 90 °C. A life cycle assessment has clearly shown the environmental interest of this approach (especially by detoxifying agricultural soils). INTRODUCTION Agromining is an emerging phytotechnology aiming at recovering metals thanks to hyperaccumulating plants (van der Ent et al., 2018). These plants are able to accumulate very high concentrations of metal in their aerial parts. For example, for nickel, the hyperaccumulation threshold is 0.1%, i.e. 10 grams of metal per kilogram of dry biomass. There are some advantages to use this technology instead of conventional mining techniques: •,Treating unconventional metal resources: they can be (i) natural soils with low concentrations but also low fertility because of the metal presence (like serpentine soils for Ni) (Bani et al., 2015), (ii) mine tailings or (iii) industrial wastes (like surface treatment sludge) after soil construction (Rue, 2017);"

Jan 1, 2018

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Recent results from electrochemical measurements demonstrate that trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates than the dithiocarbonate/xanthate (DTC) collectors. Based on the traditional analysis of collector adsorption, trithiocarbonates might then be expected to be effective for bulk sulfide mineral flotation. Previous bench-scale flotation research had shown that TTC collectors are very effective for the flotation of copper sulfide minerals and PGM (platinum group metal) sulfide minerals. More recently, the TTC collectors were evaluated for auriferous pyrite recovery in benchscale plant scale flotation testing in the United States and in plant tests at Anglogold in South Africa. TTC collectors were also applied in bench-scale testing of a PGM ore. In each case an improved separation efficiency was realized. Fundamental studies at the University of Utah examining the effect of collector structure (functional group, -O-CS2 versus .S-CS2), specifically with respect to auriferous pyrite flotation, are in progress. The effect of collector structure was evaluated with air as well as nitrogen as the flotation gas medium. Experimental techniques utilized included electrochemically controlled contact angle measurements to evaluate mineral hydrophobicity and infrared spectroscopy to explain collector adsorption phenomena at the mineral surface.

Jan 1, 2003

By Sarra Scherbakova, Alexander Kurkov, Andrey Egorov

"Deep concentration of iron ores involves extraction, in addition to magnetite concentrate, of hematite and martite concentrates and recovery of other valuable components. A flotation technology was designed specifically for finely disseminated hematite ore, allowing producing saleable hematite concentrate containing 64-66% Fe. The main process challenge is caused by the presence of other ferruginous minerals such as carbonates, silicates, and phosphates, and fine hematite and martite mostly concentrated in the -0.044 mm fraction. Main operations of the processing circuit are removal of slime, flotation to remove impurities (carbonates, phosphates etc.) with an anionic phosphorous collector in an alkaline environment, hematite and martite flotation using same collector in a slightly acidic environment to produce commercial iron concentrate. Tailings of wet magnetic separation of magnetite containing 24.5% Fe and finely disseminated hematite ore containing 51% Fe were processed to produce iron concentrates with a yield of 15% and 50%, respectively, containing approximately 65% Fe and 5% of silica. Hematite flotation tailings had the highest content of gold (up to 0.09 - 0.11 g/t), while in other products it never exceeded 0.02 g/t. Using a Knelson concentrator was able to recover 40 to 45% of the gold into 3.31 g/t Au gravity concentrate. The success of gravity concentration is due to high gravitational contrast of gold to mostly quartz and aluminosilicates in the hematite flotation tailings. In general, the proposed process can be used as a solution to the challenge of selective concentration of finely disseminated iron minerals."

Jan 1, 2014

By Leming Ou, Hongqiang Li, Li Zeng, Qiming Feng, Yiping Lu, Guofan Zhang

"The entrainment of sericite, especially in the presence of hydrophobic microcrystalline graphite, leads to the poor flotation selectivity of microcrystalline graphite ore. In this paper, it was attempted to reduce entrainment of sericite, selective flocculation of microcrystalline graphite using polyethylene oxide (PEO) was studied. For the sake of flocculate microcrystalline graphiteselectively, flocculation tests of microcrystalline graphite and sericite single mineral were conducted.To investigate the effect of selectiveflocculation of graphite on entrainment of sericite in microcrystalline graphite flotation, batch flotation tests of graphite single mineral and artificial mixtures were conducted; theflocculationselectivity of PEO of different molecular weight (M.W.) was alsocompared inartificial mixture flotation. Inthe end, the structure of flocs in different particle size was studied by sieve analysis and microscopic observation. The resultsindicated that PEO of molecular weightone million andtwo million could selectivelyflocculate the microcrystalline graphite and reduce the entrainment of sericite at a lower dosage; further increasingof the dosage of PEO(M.W. ?two million) led to hetero-flocculation between graphite and sericiteandmadethe ash content of concentrate increase again."

Jan 1, 2014

By Miguel Becerra, Daniel Jordán, Jorge Soto, Luis Torres

"Most SAG grinding operations currently use ball sizes between 5.5 and 6 inch maximum size. However, in most cases the use of this ball sizes hasn’t been justified by a phenomenological analysis of the real effect on the grinding process, but rather by trial and error. The analysis of the influence of ball sizes in SAG grinding hasn’t been developed in detail by considering the effect on process parameters inside the mill, grinding efficiency or internal classification. Historically a conventional grinding reference has been made on the empirical procedure developed by Azzaroni (1980). Further to Azzaroni’s methodology, Sepulveda (Sepúlveda, 2007) developed the SPEC methodology, incorporating the ball size effect on the grinding efficiency parameters using a population balance model included on Molycop tools spreadsheets.This paper demonstrates a detailed analysis at pilot scale of the ball size employed in SAG grinding and scaling that exists between the different levels. This analysis includes assessing the effect of balls sizes on parameters associated with grinding efficiency and its effect on the total fill level, product size distribution and specific energy consumption, among others. In a complementary way it develops a technical - economical evaluation from industrial data comparing two different ball sizes and its effect on the grinding process analysed integrally."

Jan 1, 2014

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management.This paper describes the data integration requirements in a mine, concentrator and port for unification of the redundant data. The capture of the mining events, stock pile management and the metallurgical information is the base requirements for a dynamic environment to reduce the overwhelming amount of information to unified set of information. Part of any decision support program should entail these results to continuously improve the measurement system to address the costs in mine and milling the ore."

Jan 1, 2003

By Jing Zhou

In view of the state of the long time use of sodium cyanide in lead-zinc-sulfur-silver multimetallic ore production, we propose alternative reagents system through experimental research. The experiment first used TJ, sodium sulfide to adjust the flotation pulp, after that, zinc sulfate, sodium sulfite was added to low alkaline pulp to inhibiting zinc sulfur mineral and adapted MB, 25# aerofloat and diethyl dithiocarbamate combination collectors to float lead minerals. The obtained test index is as follows: lead concentrate recovery rate of small scale test was increased by 5 to 10%, the recovery rates of gold and silver in lead concentrate were increased by 7% and 11% respectively; the industrial test is conducted under the condition that the total grade of lead and zinc content in raw ore decreased by 4.81%, the total recovery rate of lead and zinc increased by 7%, recovery rates of gold and silver in lead concentrate were increased by 7.62% and 9.65% respectively. So it successfully realizes the target to replace the sodium cyanide, using low-alkaline non-toxic reagents system in mineral processing practice of three kinds of complex lead-zinc-sulfur ore of this mine. Keywords: refractory lead-zinc-sulfur ore, depressant, non-cyanide flotation

Sep 1, 2012

In flotation, particulate materials are separated by controlling the hydrophobicity of the particles using appropriate collectors. In this regard, contact angle (?) is the most important process variable. However, the flotation models used in industry today do not include ? as a parameter. As result, flotation circuits are designed based on the first-order flotation rate constants (k) determined from laboratory experiments. A problem with this approach is that laboratory experiments usually give substantially higher k values than achievable in full-scale operations, which makes it difficult to use the model for plant design. In the present work, we have developed a model from first principles using both surface chemistry and hydrodynamic parameters, such as ?, ?-potentials, surface tension (?), particle size, energy dissipation rate, etc. The basic approach is similar to the one developed previously for bubble-particle interactions under laminar flow conditions (Yoon and Mao, J. Colloid and Interface Science, 181, 61, 1996) except that the model parameters have been modified by considering the turbulence in a flotation cell. In addition, the model describes the recovery processes in froth phase, including bubble-coarsening due to coalescence. Based on this model, we have developed a computer simulator (FlotSim) that can be used to design flotation circuits from the mineralogical (or liberation) data on the feed and the hydrodynamic characteristics of a flotation machine. Since the model is dynamic, it can also be used for process control. Further, the simulator has predictive capacity as it is based on a first-principles model. The model-based simulator has been validated in a carefully controlled bench-scale flotation experiments. Keywords: flotation kinetics, flotation model, contact angle,?-potential, size-by-size recovery, liberation, DLVO theory

Sep 1, 2012

By Jurgens J. Louw, Vincent C. Smith, Gareth C. Smith, Agit Singh, Dave G. Hulbert

"The flexibility of the PlantStar control platform has enabled Mintek to investigate and easily develop new control strategies for both milling and flotation. This includes a Solids Feed Controller, a Safety Limit Controller, Mill Power Optimiser and Flotation Optimiser, amongst others.The solids feed controller was developed for minerals processing plants using a specialised time delay compensator. Using conventional time delay compensators that are purely model based, results in robustness problems due to model uncertainties. The Mintek Solid Feeds Controller makes use of a plant model, but compensates for model inaccuracies, giving more controller stability and a more robust delay compensation algorithm.The safety limit controller has been developed to switch smoothly between normal and safety control loops without bumping the process. The safety loop output is chosen in accordance with a predefined list of priorities and whether the respective constraint boundaries are exceeded.The Mill Power Optimiser helps to find the power peak on the mill power curve. This insures maximum grind with maximum throughput. It also prevents power dips due to mill overloads, making the milling circuit easier to operate.The flotation optimiser algorithm analyses trends of all accessible variables in the process. The algorithm uses this information to calculate operating conditions that will control the residence times, mass pulls and circulating loads within a flotation circuit to a specified setpoint. Research is being done to now optimise these setpoints in order to achieve better recovery."

Jan 1, 2003

By M. A. C. Goes

Over the last twenty years CETEM has been involved in the preparation and certification of reference material from ores, concentrates and related materials for use in analytical laboratories associated with mining, metallurgy and earth sciences. CETEM provides reference materials from mineral samples, not available from the existing sources, to meet the needs of the mining and mineral industry. CBPA-1 and CBPA-2 respectively are samples of copper sulphide ore and flotation concentrate, both originated from Sossego Mine, located in Pará State, Brazil. The batch characterization was carried out by a collaborative measurement program with participation of 20 industrial, commercial and government laboratories from South America, North America, Europe, Asia and Africa. The certificates and report were issued in December 2007 (http://www.cetem.gov.br/ mrc/ing). The objective of this paper was to describe the procedures for material preparation and the collaborative approach involving a collaborative interlaboratory measurement program to certify CBPA-1 and CBPA-2.

Jan 1, 2014

By J. B. Yianatos

A practical an interactive model to describe the operation of a flotation bank of mechanical cells was developed based on the hydrodynamic and metallurgical characterization of large industrial flotation cells. Thus, the mineral grade and recovery, as well as the stream properties along the flotation bank can be described in terms of the operating variables. The model was built considering the flotation bank as a distributed system, so the solution for the water and solids mass balances, per size classes, for each single cell, are sequentially solved. Also, each cell was described by two distinct zones, the collection zone characterized by the flotation rate constant and the froth zone characterized by the froth recovery. The mineral feed was described in terms of the mineral species and particle size classes, using a rectangular flotation rate constant distribution. Also, the effect of changing the actual operating variables (air flowrate, pulp level, pulp density, pulp flowrate, etc.) on the mineral collection process, in the collection (pulp) zone, was considered downstream along the bank. The froth recovery of floatable mineral has been estimated by measuring the mass flowrate of particles entering the froth by true flotation together with the concentrate mass flowrate (ton/h). The mass flowrate of collected particles at the pulp/froth interface level was calculated from direct measurement of bubble load (ton/m3) and gas flowrate (m3/h). Flotation recovery is mainly related to the froth depth and air flowrate. All parameters considered in the model have been adjusted from direct measurements in plant site. Also, the effects of other operating variables such as reagents dosage, top of froth grade, or froth discharge velocity are presently under study. This procedure has been tested using data from industrial rougher operations consisting of flotation banks with 5 cells to 9 cells in series, and different cell sizes, such as 45m3, 130m3, 160m3 and 250m3. Thus, it has been shown that the model approach is a powerful tool for flotation cells diagnosis, operation and development of new control strategies, as well as, to evaluate the effect that de-sign and operating variables have upon the collection and froth zones performance in large flotation cells.

Jan 1, 2014