Search Documents

By Pratter P., Boley C.

Polymers are well established in geotechnical applications, for example in ground improvement, where the polymers act as a binder that, when cured, holds the grains together by adhesive and cohesive forces. The subject of this research work is an innovative composite of polymers and gravel, which differs from conventional grouting materials due to its adjustable material properties. With these specific properties, the semi-rigid material can be optimally adapted to the local ground conditions and the individual framework conditions of a construction project. For the characterization of the composite material, stateof- the-art methods, such as image processing by segmentation, are presented. Segmentation is suitable for quality assurance and monitoring of laboratory samples and soil samples directly from ground improvement on the construction site. The load-bearing capacity of the innovative material can even be increased to the order of magnitude of concrete. For this reason, the soil mechanical laboratory tests in this research had to be modified and even expanded by rock mechanical laboratory tests. Based on the experimental investigations, the importance of this innovative material for practical application is demonstrated by a calculation example from construction practice, which shows that even difficult ground conditions can be handled with it.

May 1, 2022

By John P. Turner, Benjamin J. Turner

"Tieback anchors are now used routinely for landslide stabilization in the USA and abroad. It is generally understood by design engineers that friction loss over the unbonded length of a tieback anchor is inherent to the system, and such loss is permitted as long as it does not exceed a certain threshold, typically 20 percent of the post-tensioning load. However, recent experience from projects utilizing tieback anchors with unbonded lengths in excess of 150 feet has demonstrated that this criterion may be difficult to achieve, particularly in certain ground conditions. Furthermore, anchor friction loss, even if below the 20-percent threshold, has important implications for the stability of the slope that are often ignored in practice. This paper presents the results of a study in which friction loss is quantified from load test data for projects in a variety of ground conditions by means of a “wobble coefficient.” Factors that may influence the wobble coefficient are examined, and recommendations for addressing this issue in practice are presented. A recent instrumented load-test program for a landslide stabilization project in Southern California is examined, demonstrating that with appropriate monitoring controls, uncertainty with regard to friction loss can be minimized. IntroductionSteel-strand tieback anchors have been used by the geotechnical community to support shoring systems for many decades, and more recently as a means to stabilize landslides. For strand encased in grease-filled plastic sheathing, which is intended to allow the strand to elongate freely, some load can still be transferred by friction between the strand and the grease and between the grease and sheathing. The sheathing then transfers load to the surrounding grout and, in the case of ground anchors, to the surrounding soil or rock. The resulting decrease in load over the length of the unbonded zone is known as “friction loss.”A widely used criterion for ground anchor acceptance based on load testing is that the measured anchor elongation must achieve a minimum value of 80 percent of the theoretical elastic elongation, or in other words the actual elongation can be up to 20 percent less than the theoretical value. This ensures that the majority of the load applied at the anchor head is reaching the bond zone behind the assumed failure surface, since load shed within the failure mass does not contribute to stability. This criterion acknowledges that friction loss is an inherent feature of the anchor system which cannot be eliminated completely, only minimized."

Jan 1, 2017

By Chu E. Ho, Paul Napoli

This paper presents the performance of nineteen open-ended steel pipe piles driven through highly variable overburden soils into glacial till and schist bedrock. The piles were 16 inches in diameter and 0.656 inches thick, with yield strength of 50 ksi. The piles were designed for a service capacity of 250 kips and were driven to achieve an ultimate geotechnical capacity of at least 500 kips. Due to the large variation in the ground conditions, installed pile lengths ranged from 25 to 66 feet. Some piles were driven to refusal on the bedrock while others were terminated at final driving resistance of 2 to 7 blows/in. Two piles were suspected to be plugged during driving while others did not. Each pile was instrumented with strain gages and accelerometers near the pile top, and observed using a Pile Driving Analyzer (PDA) to provide preliminary guidance on pile capacity achieved at end of initial drive (EOID). The influence of plugged and unplugged pile toe conditions on the interpretation of pile capacity was investigated using Case Pile Wave Analysis Program (CAPWAP). Characteristics of driving energy, compressive and tensile stresses developed in the steel pipe piles, and the resulting pile deformation behavior are discussed. INTRODUCTION The Hunters Point South redevelopment in Long Island City, Queens is one of New York City’s major efforts to transform former manufacturing zones into mixed developments for the middle-income community. The site is located along the eastern shoreline of the East River and Newtown Creek. The development included low to high-rise residential buildings, a public school and retail structures. Open spaces were created along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community related activities. Waterfront structures included small park buildings, walkways and viewing platforms with the shoreline protected by revetments as part of the City’s flood mitigation strategy. The project was implemented in two phases, with completion of construction for Phase 1 in 2013 and Phase 2 in 2019. Based on available historical information, extensive reclamation took place between 1855 and 1898. After 1951, changes to the shoreline were made along the East River, including the removal of reclaimed land along the northern portion of the project site to allow for docking facilities. By 1977, these facilities had been demolished and backfilled to form the current shoreline configuration. The present site was temporarily used as a parking lot with stockpiles of fill mixed with construction demolition rubble, rip-rap and boulders of varying heights across the site. The existing ground surface varied significantly up to approximately 25 feet difference in elevation. The stockpiles were removed and the site was re-graded during final development of the project. This paper discusses the foundation design challenges due to the loose overburden soils and potential obstructions within the fill material, in particular, the issues relating to installation of open-ended steel pipe piles through the ground conditions encountered on site.

Jan 1, 2019

By Tai Luu, Maxim C. Schisler, Yaser Taheri

The Stevens Gateway Project is an expansion of the Stevens Institute campus overlooking the Hudson River in Hoboken, NJ. The plans call for 90,000 ft2 (8360 m2) of new classroom, research, and student life facilities in new, 4-story buildings. The excavations for the building footprints were bounded by city streets and existing buildings, including the historic Carnegie Laboratory of Engineering, built in 1902. Pit underpinning was originally specified for the Carnegie building. However, given the depth of cut, construction time required for the 13 ft (4.9 m) deep pits would be substantial. The geotechnical contractor retained for the support of excavation work therefore offered an innovative active soil nail wall design that would meet project requirements in a shorter timeframe. Unlike the passive soil nail systems common in the industry that are chiefly used for soil slope stabilization, active soil nail walls contain pre-stressed anchor components to resist soil movement and limit settlement of soil and structures being contained. In addition to a discussion of the overall design approach of the active soil nail wall system, this paper will include a detailed description of its constructability and effectiveness. This project’s use of a conventional slope stabilization technique for an unconventional purpose may have positive implications going forward. INTRODUCTION Stevens Institute of Technology is a private university in Hoboken, New Jersey that sits on the cliffs of the City of Hoboken overlooking the Hudson River and Manhattan Island to the east of the campus. In recent years, the university has executed numerous plans to expand and upgrade its campus academic, student life, and residential facilities. One such project is the Academic Gateway Complex. The plan adds 90,000 ft2 (8360 m2) of new classroom, research, and residential facilities while also enhancing community connections by building a park to serve as a green corridor for the city. The proposed construction took place on the north and south side of 6th Street between Hudson Street and River Street. The project included the demolition of an existing university building followed by the construction of two, 4-story buildings on the north and south property lots. The north and south buildings will be connected by a second floor bridge spanning 6th Street. The buildings each contain a full basement extending from the proposed ground floor at approximately El. 41ft (12.5 m) to the basement subgrade at El. 26 ft (7.9 m). Each building will be constructed on respective mat foundations. Figure 1 presents an overview of the project area.

Jan 1, 2019

By Bo Westerberg, Mattias Andersson, Yvonne Rogbeck

"Deep stabilisation has been used in Sweden for decades. The method has been improved to allow it to be used in different types of soils and with new binders. One challenging soil type in Sweden is so-called sulphide soil, a fine-grained soil which contains organic material and iron sulphides. There have been some cases in Sweden of problems when using deep stabilisation in this type of soil, and in one case a slope failure occurred. This paper shows that it is possible to achieve good results with deep stabilisation in sulphide soils. Laboratory and field studies from a test site along the Botniabanan railway line in Sweden are presented. Geotechnical and chemical properties of the natural soil were investigated in the laboratory and one or more of these properties may explain the differences in the stabilising effect of sulphide soils. The strength of the laboratory samples and the columns in the field were tested and compared. It is shown that a satisfactory stabilisation effect can be achieved with the proper choice of binder, amount of binder added, curing time and mixing energy. In sulphide soils, more binder additive is needed than in “ordinary” inorganic clays.1. INTRODUCTIONThe term sulphide soils is used in this paper to refer to the unique types of sulphide soil commonly found in the coastal areas along the north-eastern coastline of Sweden between the cities of Gävle and Haparanda, a distance of about 900 km. Sulphide soils are in general very compressible, susceptible to creep deformation and normally show low undrained shear strength. A sulphide soil may have a negative environmental impact through acidification and chemical action if it is subjected to oxygen, for example during excavation or lowering of the ground water table, Mácsik (1999). In foundation engineering works, efforts are made, for environmental or/and economic reasons, to use the sulphide soil as the foundation instead of excavating it. Deep stabilisation by means of columns is a potential method for use when sulphide soil needs to be improved in order to reduce settlements or/and increase the stability of embankments.Sulphide soils were formed as sediments at river mouths and off the coast in the special environment prevailing at the time of sedimentation, Mácsik (1994). The water in which the sulphide soil was sedimented was brackish/sweet and the environment was typically deficient in oxygen. The environment prevented complete decomposition of the organic material in the sediments. As a result, sulphide soils were formed primarily in the form of a fine-grained composition of clay and silt minerals, iron sulphides and organic matter. Such environments still exist today and new sulphide soil sediments continue to be formed."

Jan 1, 2015

By William H. Walton, Joel Dellaria, Jeffrey R. Hill

The City of Chicago has a world-renowned skyline and is known for its provocative architecture. The subsurface conditions in the city have allowed for construction of these significant structures. The skyline is supported on caissons as they are called in Chicago or drilled shafts in other locations. Despite the significant strides the industry has made in advancing the drilled shaft, the use of other specialty geotechnical construction techniques like micropiles has not been overlooked in Chicago and the surrounding areas. Micropiles have been utilized to underpin famous existing historic structures like Orchestra Hall any many others. Engineers have used 200 to 600 kip micropiles to underpin compromised, inadequate, or damaged caissons. The paper will discuss the use of drilled shafts, micropiles, and ground improvement over the last 30 years in Chicago using a curated collection of case histories. It will also examine advancing the industry beyond its current technical limitations using these techniques. INTRODUCTION 20,000 years ago, glaciers from the Chicago region left behind sheets of glacial clay till underlain by dense, over consolidated glacial till below: limestone bedrock, found about 100 ft below street level. An unusual feature in this profile is the soft Chicago Blue Clay. Chicago has been called the birthplace of the Skyscraper and drilled shaft foundation, both of which came about in the 19th century. After the Great Fire of 1871, tall new structures were built rapidly and designing a successful foundation was trial and error. The first deep driven wood pile and caisson foundations bypassed the problem layer and found solid support on hardpan till or bedrock below (Schock and Risberg 2013). Once the drilled shaft foundation became acceptable to the Chicago engineering and construction community, building heights and complexity grew dramatically. As the city grew, building foundations were being repurposed. There was also the need to underpin structures for additional loads and shallow foundations for adjacent construction. Hand-dug drilled shafts were an option for some of these restricted access and low headroom sites but a new technique, micropiles, would prove to be the future of retrofit and hard to construct foundations. Micropiles were introduced on a limited basis to the United States market in the 1970s and 80s. In the early 1990s, the Chicago market began to latch onto micropiles and their use has grown significantly as a solution to the most complex foundation problems a maturing skyline has to offer.

Jan 1, 2019

By Chandramohan P. V., Ravi Kishore

"An underground reservoir was to be constructed at Doha in Qatar. Simsima lime stone is present at the bottom. When the reservoir is empty, there will be uplift at the bottom but this will change to downward load when it is full. The rock at the bottom had high bearing capacity to resist downward load. But uplift had to be resisted by piles or anchors. The reservoir has a size of 120mx80m. Shrinkage and creep of concrete coupled with thermal contraction imposed a horizontal movement of 26mm on the extreme piles. So, piles have to accommodate this as well. This unique situation needed a unique solution. The solution was to provide piles with flexible high tensile strands to take tension. An annular space near the head of the pile would facilitate horizontal movement as well. Compression load was directly passed on to the raft bearing on rock.INTRODUCTIONAn underground reservoir for storage of drinking water was to be constructed at Doha, Qatar. The reservoir was proposed to have a plan size of 120m x 80m. Clear height inside the reservoir was proposed as 17.2m, from the bottom of roof to the top of bottom raft. Overall height of the reservoir at the outlet from the top of the roof to the bottom of raft was to be 21.2m. For the sake of inspection and in order to prevent pollution from the surroundings a gallery was planned around the reservoir. This could accommodate pipelines as well. This gallery was 3.0m wide on three sides and 8.4m wide on the outlet side.The gallery had removable gratings as cover in order to facilitate maintenance. Capacity of the reservoirwas proposed to be 40million gallons. The reservoir is divided into four compartments with baffle walls in each one for water circulation. Roof of the reservoir is kept at 300mm above ground level. There are two levels of car park on top of the reservoir. Top of the reservoir roof is at +14.35. Bottom varies from - 6.68 to -7.08. Lowest water table is at +6.00. Concrete structure of the reservoir was designed by a local consultant. The Navayuga Engineering Company was entrusted with the construction. Please see Figs 1 and 2."

Jan 1, 2017

By Patrick van der Schaaf

"During 2016, foundation piling works were completed to allow for the construction of a production and storage/handling terminal in Rotterdam. It is there that steel foundations will be produced for offshore wind farms and the oil and gas industry. Several Dutch contracting companies were involved in constructing: foundations for an assembly hall, a barge quay and a deep-sea quay wall. For the hall foundations, cast in situ concrete vibro piles were created. Open ended steel casing piles were also installed due to very high cone resistances which made it impossible to perform cast in situ piles in certain areas. The quay wall was constructed with open ended steel casing piles in combination with sheet piles. A deep-sea quay wall was also constructed to provide enough storage area for the offshore mono piles. This project was unique and challenging due to the use of different foundation technologies in challenging circumstances and soil conditions. This paper will give an insight into the Dutch use of varying foundation piling techniques for deep-sea quay wall constructions. It can be concluded that even experienced local contractors can be surprised by variations in soil conditions. It will also show how the contractors adapted to the difficult circumstances.PROJECT OUTLINEThe project consisted of a barge quay near the assembly hall with a length of 500 metres, width of 42 metres and a height of 35 metres, and a deep-sea quay wall 480 metres in length. This paper concentrates on the foundation works for the construction of the deep-sea quay wall. The construction of the deep-sea quay wall consisted of a combination of open ended steel casing piles with a diameter of Ø 1420 mm and a wall thickness varying between 21 and 23 mm. The lengths of the steel casing piles varied between 32 and 37 metres. Between the steel casing piles triple PU 28 sheet piles were installed with lengths varying between 26 and 29 metres. In the Netherlands, a combination of open ended steel piles and sheet piles is known as a “combi wall”. For the deep-sea quay wall a steel combi wall was shored with steel H- section profiles that were driven in a raked position whilst being injected with grout, so called MV-piles. The MV piles for this project consisted of steel HEB 600 sections with lengths from 52 up to 59 metres and were installed with angles varying between 42.5 and 47.5 degrees. For a detailed overview regarding the project specifications reference is made to table 1 which is presented below."

Jan 1, 1900

By Mu Chen, Ye-Shuang Xu, Dong-Wei Hou, Shui-Long Shen, Huai-Na Wu

"This paper presents a laboratory investigation on the mechanical behaviors of the cement-clay admixture improved by polypropylene fiber. Cement can significantly improve the clay admixture. The fiber additive also improves the strength and ductility of the improved clay. The Unconfined Compression Strength (UCS) of the polypropylene fiber-reinforced cement-clay presents an overall trend to grow with the increase of fiber length. The improved clay reached its peak strength at the fiber content of 0.5%. Then the UCS of the improved clay will slowly reverse if the fiber content continues to rise. For study of curing time, improved clay behaves better in its early strength, but an inhibition will be brought about if fibers are excessive.INTRODUCTIONGround improvement technology is essential for construction of structures in soft ground. Some traditional techniques often cost much but result in little. For instance, along the coastal region of China, soft ground is often improved by backfill with high quality sandy soil transported far away, leading to high additional haulage costs and long construction period. Reutilizing the excavated soil as backfill or subgrade after treatment, by contrast, will be more economical and effective (Hufenus et al., 2006). Many researches have been conducted to improve the compression strength of soft soil, among which, the method of mixing the soft soil with cement and fly ash is one of the most common ways (Kolias et al., 2005; Horpibulsuk et al., 2009; Porcino et al., 2012). It is known that soil resists well against compression and shear force but behaves poorly in resistance to tension. Therefore, utilizing tensile elements such as fibers and strips to improve the tensile strength will be effective because of its strength isotropy, better durability and cost effective (Haeri et al., 2000; Kaniraj and Havanagi, 2001; Consoli et al., 2010)."

Jan 1, 2015

By Ali Azizian, Brian Hall

"Driven piles were selected to support the Fraser Heights Bridge bents. Piles were a key component of the top-down construction approach, which was adopted for minimizing potential impacts on an environmentally sensitive wetland. Project requirements mandated verification of pile capacities using dynamic methods. More than 40 Pile Driving Analyzer (PDA) tests were performed. The subsurface conditions were highly variable. On the east side, piles extended through loose sands, soft silts/clays, and two peat layers and were founded in glacial till-like soils at about 45 m depth. However, on the west side, till-like materials were so shallow that it was difficult to drive the piles sufficiently deep to obtain the necessary lateral support. This paper provides an overview of the geotechnical considerations of the bridge design and top-down construction approach, and expands on the presentation of PDA results and how they compared to pile capacity estimation methods and parameters recommended in the applicable design codes.INTRODUCTIONThe Fraser Heights Bridge (FHB) was a component of the Fraser Heights Connector (FHC), a 2 km section of the South Fraser Perimeter Road (SFPR), constructed as part of the Port Mann/Highway 1 (PMH1) Improvement Project. The FHC is located in northeast Surrey BC (Fig. 1).Two major design and construction determinants were: 1) a mandated tight schedule to provide a non-tolled alternative to a new toll bridge; and, 2) an obligation that construction had to occur with minimal impact on the environmentally sensitive wetland the FHB crossed, including limiting the footprint of the permanent and temporary works to less than 45 m2, and prohibiting construction access onto the wetland. Construction equipment was only allowed on the wetland on temporary trestles or on the finished structure. This latter requirement resulted in the bridge being constructed span by span, using a top-down approach."

Jan 1, 2016

By John C. Niedzielski, A. Frances Ackerman

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site’s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The fullscale field test played a significant role in the design of the project’s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

Jan 1, 2017

By Michael J. Weaver

Urban redevelopment projects are occurring more frequently than ever before as urban greenfield sites become limited and city planners and devel- opers attempt to revitalize existing underdeveloped neighborhoods. How- ever, because of the past usage of many urban sites (some dating back 100 years or more), designers and construction teams have to not only engineer founda- tions to accommodate the subsurface soil and ground water conditions, but also to work around the relic founda- tions or structures that have been left behind from previous developments. In these cases, a one-size-fits-all approach to foundations may not yield the most cost- and schedule-effective approach, and hybrid foundation systems have to be evaluated.

Apr 1, 2022

By Uwe Hess

For the Danish landworks for the coming fixed link between Denmark and Sweden across the Øresund the focus has been on the environmental aspects of the construction and operation of the facilities. This paper describes how the environmental objectives pertaining to the project have influenced the design and construction of one of the major elements of the Danish landworks, i.e. the tunnel in Sydhavnsgade and under Sydhavn Station. The chosen construction methods for the construction pit bracing and the groundwater lowering will be described along with the observed effects on the environment as shown by simulated or measured values for noise impact, settlements, pumped groundwater and extension of the drawdown cone.

Jan 1, 1996

By Dario Libano, Franz-Werner Gerressen

"Diaphragm walls are known as underground structural elements commonly used for retention systems and permanent foundation walls or elements. Of course they can also be used as deep groundwater barriers. This paper will focus on the construction work in an urban area like Sao Paulo. The Line 5 of Metro Sao Paulo is one of four network expansion projects undertaken at the same time. The projects will cover various areas of the city. The Line 5 on São Paulo’s south-side will be extended 7.1mi (11.5km) to serve 770,000 riders per day, stretching a total of 12.4mi (19.9km) along 17 stations. The extension line will facilitate access to the city’s central section and the commercial and hospital districts located along the line. The Brooklin Station, subject of this paper, had to be carried out in a special five shaft shape design, shaft diameter 131ft (40m) each, without using ground anchors. A focus will be taken on the special requirements of the installation of the arrows as well as on the specialties of installation for the shaft shaped layout. Therefore, it was required to install a 3.3ft (1,000mm) diaphragm wall using a specific layout especially in the connecting sections of the shafts, the so called arrows, to provide a bearing area for the struts. Maximum wall depth was about 121ft (37m); the total volume was about 20,060 cubic yard (15,337m³). The paper will describe the construction method and the sequence of activities required for the construction of this diaphragm wall using a combination of hydraulic grab and trench cutter system.INTRODUCTIONThe Line 5 Extension, in the city of Sao Paulo/Brazil, is currently the most important investment in public transport by Sao Paulo state’s government. It will connect the south part of the city to the city center, crossing through four other major METRO lines and stations, all currently in operation. The extension includes a new parking yard for the trains and 11 new stations. The Brooklin Station is one of the new stations and has a unique geometry of five secant shafts. The station should open and operate in 2016.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One of them was to contain the contamination plumes in the neighborhood and the other for temporary support to enable the excavation of the shafts. The final retaining wall design was reviewed and changed to a concrete structural diaphragm wall. The reason of design change was as well the reduction of construction time of the shafts by half to meet the schedule as to avoid dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a trench cutter (hydromill) was used in such a situation in Brazil. The cutter increased the quality of the joints by overcutting, and decreased the probability of having seepage into the shafts. The cutter created a seepage barrier and avoided movement of contamination."

Jan 1, 2017

By Hee-suk Yun, Dae-jin Hwang, Jeong-woo Seok, Myoung-mo Kim

"In this paper, the accuracy of the data measured by a newly developed displacement measuring system, DPRMs (Digital Pile Penetration and Rebound Monitoring system) and its applicability as a quality control tool were verified by field measurements of pile penetration and rebound for pile driving performed at 3 construction sites and 1 test site. The DPRMs data were found to be much better than handwork data. A new dynamic formula for pile capacities is proposed uses the results of a pilot dynamic load test and the final pile penetration. The ratios of pile capacities obtained by the new formula to those by the dynamic load test were 94%±7.4% in the contrast with 123±28.3% by the 5S formula and 68±24.0% by Hiley's formula. This result shows the superiority of the new formula. The ratios of the maximum compressive stresses calculated by using DPRMs to those calculated by using PDA (Pile Driving Analyzer) were about 90-110±10%. This result confirms the applicability of DPRMs as an overdriving monitoring tool. Two sets of DPRMs were used to measure the 3-D displacement behavior of a pile head at the test site. The more the pile head moves laterally, the less the final set values were expected because of the loss of driving energy, but this trend was not obvious within the limited data obtained at the test site.INTRODUCTIONPile construction monitoring consists of two parts. In the first part, enough capacity of the pile is secured to stand the design load. In the other part, pile damage during driving is prevented. Although several methods can be applied to achieve the first part, PDA is nearly the only tool for measuring pile stress.Several methods such as a static load test, a dynamic load test, an Osterberg cell, and numerous driving equations can determine the pile capacity. Among them, the static load test and the dynamic load test are most widely used. The static load test is advantageous because it has the highest reliability. The disadvantages are as follows: it is costly and time-consuming. Also, the capacity of the pile under construction cannot be evaluated. The dynamic load test has lower reliability than the static load test, but it is cheaper than the static load test, is reliable enough to determine the pile capacity, can evaluate the capacity of a pile during construction, and can offer information about construction conditions such as the pile integrity and the pi le stress during driving. The dynamic load test takes a relatively short time and is low cost compared with the static load test. However, it is still costly, time-consuming, and unnecessary to apply to all piles in the field as a construction measurement tool. Therefore, driving resistance (blowcounts) is commonly measured to confirm the pile capacity at construction sites."

Jan 1, 2005

By Xiaocen Lu, Guowei Li, Jiantao Wu, Thang N. Nguyen, Andrew C. Amenuvor

"This paper investigates the effect of driving a group of 52 open-ended Prestressed High Strength Concrete (PHC) piles on an existing highway embankment based on field measurements of excess pore pressure and lateral soil displacement. Excess pore pressure due to pile driving increased with depth and decreased with increasing distance from the pile, influencing a distance of 43 pile diameters. For pile groups, the rate of dissipation of excess pore pressure decreased with increasing depth and averaged 79% in 20 days, during which maximum ultimate bearing capacity was not yet attained. Lateral soil displacement continued to increase for a period of time after the end of pile driving and this could have resulted in significant inclination of piles if pile installation was too quick and pile spacing was too small. Lateral soil displacement due to pile group decreased with decreasing distance to the existing embankment as a result of high soil density produced by the embankment loading. The results also indicate that the effect of pile group installation on the existing embankment is negligible.INTRODUCTIONPile driving can cause excessive lateral displacement of soil and heaving of the ground surface, which may adversely affect nearby structures. In addition, lateral deformation and excess pore water pressure resulting from pile driving can exert lateral pressures and vertical forces on the piles, and impact negatively on the project and its surroundings. Therefore, it is important to evaluate the influence of pile driving on the nearby structures as well as the project itself when expansion works are carried out.Recent years have seen some development in the application of field tests for studying soil disturbance due to piles, and these tests usually involves pore water pressure and lateral soil displacement monitoring during pile driving. Results of field experiments performed by Reese and Seed (1957) in San Francisco Bay Mud with instrumented piles showed that pile installation generated large pore water pressures at the pile surface, with only slight increase at a distance of 15 pile diameters away. The measurements indicated that the increase in pore water pressures can exceed the initial total overburden pressure. Holtz and Lowitz (1965) reported a decrease in undrained shear strength immediately after pile installation, which was largely recovered after full pore pressure dissipation for field measurements within 1.5–2 pile diameters from the pile surface. Hwang et al. (2001) presented results of large scale pile driving tests where maximum excess pore water pressure generated decreased rapidly with increasing distance from pile. The excess pore water pressure became negligible at 15 pile diameters from the pile. Their results also showed that lateral displacement of the ground decreased with increasing distance from the pile. Pestana et al. (2002) carried out full-scale closed ended pile tests in the Young Bay Mud deposit. Higher excess pore pressures were observed for points closer to the pile, which decreased with increasing distance from the pile wall. Exponential decay of excess pore pressure with time was also noted. An 80% dissipation of excess pore pressure was achieved for soils more than one pile diameter away from the pile wall between 50 to 80 days. Lateral deformation generally decreased with increasing distance from pile wall, whilst varying erratically with depth. Bozozuk et al. (1978) reported on soil disturbance due to driving of 116 concrete piles in sensitive marine clays in a construction project. Maximum pore water pressures after pile driving within the group, and 6m (20 pile diameters) from the group were over 35-40% of the total overburden pressures, and the influence of pile driving on pore water pressure at 20m away from the group was very small. Cooke and Price (1973) studied a 168-mm-diameter instrumented pile jacked into over consolidated London clay. Outward lateral displacements ranging"

Jan 1, 2016

By Chaz Weaver, James Sheahan, Michael Mo

"The Virginia Department of Transportation (VDOT) undertook a program to replace four bridges along approximately 4 mi (6.4 km) of US 340 in Northwest Virginia. Two of these bridges, which span Compton Creek and the Norfolk Southern Railroad respectively, are the subject of this article. HDR provided roadway and structural design as well as geotechnical engineering services for the Norfolk Southern Railroad Bridge while their subconsultant, Saeed Associates, provided structural engineering services in support of the HDR roadway and geotechnical team for the Compton Creek Bridge.The project is located in the Valley and Ridge Geologic Province of Virginia, on an alignment that is adjacent to the Shenandoah River. The project lies within the Beekmantown Group consisting of limestone and dolostone that are prevalent and prone to karstic activity in a band that passes through the project area and north into Central and Eastern Pennsylvania. This area has been impacted by karst limestone conditions where caves and sinkhole activity is common. Caves at Luray and Front Royal, located to the south and north of the project, respectively, are popular public attractions.Since the potential for variability of subsurface conditions can be, and often is, greater in karst terrain, the need to develop a design that provides as much flexibility as possible during construction, and then to be prepared to efficiently review and respond to construction questions is heightened. Coordination and communication among the design staff, VDOT’s design and construction staff, and the contractor was a key factor in completion of this project.Compton Creek BridgeThe alignment for the new Compton Creek Bridge is located about 125 ft (38 m) west of the existing bridge, placing it between that bridge and the existing Norfolk Southern Railroad Bridge. No information about the foundations was available for the existing bridges. Borings in the Compton Creek valley encountered extensive voids (some clay filled and some open) with numerous boulders, rock ledges and pinnacles, particularly on the north side of the creek. Geophysical and geotechnical investigations indicated that below a poor and variable upper zone of rock was a layer of more competent and consistent limestone, which appeared to contain little or no voids."

Jan 1, 2017

By Dewey W. Geary, Rachael V. Bisnett, R. Michael Bivens, Thomas G. Andrews

"The powerhouse for the Red Rock Hydroelectric Project is being constructed at the toe of the existing U.S. Army Corps of Engineers’ Red Rock Dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends though overburden and 40 feet into rock. Prior to rock excavation, a grouting was performed around the excavation for the purpose of increasing the strength of zones of fractured rock. For the majority of the perimeter, the rock was fairly tight and grout takes were relatively low. However, for a 160 foot extent along the landside of the excavation, extensive grouting was required to treat a two to five foot thick zone characterized by artesian flows from grout holes on the order of 20 gallons per minute (gpm) or higher from a voided zone in rock that was partially filled with sand, clay, and rock fragments. This paper discusses the treatment measures used to fill and improve the strength of this zone, which ultimately entailed a combination of thick cement grout and polyurethane grout, holes spaced as close as 18 inches on-center, and two additional rows of grout holes.IntroductionThe Red Rock Hydroelectric Project (Project) is currently under construction at the existing U.S. Army Corps of Engineers’ (USACE) Red Rock Dam on the Des Moines River near Pella, Iowa. At peak generation, the Project will generate up to 55 MW with an average annual energy output of 178 gigawatt-hours.The powerhouse for the Project will be located at the toe of the existing dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends up to a depth of 40 feet into rock through the St. Louis Limestone and terminates in the Warsaw Limestone. Prior to rock excavation, grouting was performed around the excavation for the purpose of improving the strength of zones of fractured rock. An auxiliary benefit of the grouting was reducing seepage into the excavation. Grouting began on July 20, 2015 and ultimately concluded on September 26, 2015.Drilling and grouting occurred as planned on the riverside (southwest) of the excavation along the cellular cofferdam and stilling basin wall (grout holes P-1 through S-13) and on the upstream (northwest) side of the excavation along the secant pile excavation support wall (grout holes P-14 through S-19) (refer to Fig. 1). The rock in these areas was generally tight with relatively low grout takes. However, on the landside (northeast) of the excavation (grout holes P-20 through P-28), partially infilled voids and artesian flows were encountered during drilling generally between depths of about 28 to 40 feet."

Jan 1, 2016

By Timothy Nelson, Simon Burnworth

"The Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California, Berkeley campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home.The site was perfect; located one block east of bustling downtown Berkeley and its rapid transit station, and directly across the street from the western entrance to the UC Berkeley campus. Thousands of pedestrians pass by the site on a daily basis, thus granting BAMPFA the opportunity to reshape the corner of Center and Oxford Streets with a building that would not only welcome visitors to campus, but also serve as a creative hub for both the City of Berkeley and the UC Berkeley institution itself 1.The original museum plans, drawn up in the mid-2000s, called for complete demolition of the existing abandoned facility and replacement with a visually stunning structure designed by renowned Japanese architect Toyo Ito. Even at this point, the shoring and means and methods requirements of the project were identified as a challenging component, incorporating a shored excavation bounded on three sides by busy city streets and a fourth side by an operating bank and occupied apartment building. Furthermore, a sequenced demolition would be required for the printing press facility’s three-story Administration Building (also known as the Admin Block), one-story printing press warehouse (also known as the Press Building), and an adjacent parking structure. Degenkolb Engineers was retained at that time as the shoring engineer to design the shoring to facilitate this work."

Jan 1, 2016

By Vijaya Bhushan Rao, Jason Redgers

The typical Vibrocompaction projects undertaken in the UAE are on reclaimed Sands. These Sands which are predominantly the crushable, calcareous, carbonate sands found locally as opposed to the more common quartz or silica sands that are featured in most design literature. The famous reclamations such as the iconic Palm Jumeirah in Dubai, often have specification for mitigation of liquefaction induced settlements, bearing capacity increases and total and differential settlement requirements. Often these performance targets are achieved by the means of achieving a particular relative density that are generally measured by a defined Cone Penetration Test, CPT targeting values of cone resistance (Qc), MPa at respective depth zones. In this paper some case studies are presented, where soil suitability for deep compaction by vibratory methods was firstly assessed for suitability using the Massarsch, 1991 compactability chart prior to the application of vibrocompaction and its subsequent evaluation. One such project named the Island Development required 17 to 23m depth of penetration only to treat the lower 5 to 6m of sand above rockhead as eventually the top 15m of sand will be further excavated to allow for the construction of basement. The paper will present pre and post CPT results, the results of initial site calibration trials and evaluation of the completed works.

Oct 1, 2022