Search Documents

By S McQuitty

The metallurgical treatment of Falconbridge ore re-quires an extremely fine grind of the pyrrhotite portion ? for maximum liberation and recovery of nickel. This paper describes the operation of a grate discharge pebble mill in closed circuit with cyclones regrinding 25 to 30 tons per hour of sulphides to approximately 90 per cent minus 325 mesh. The consumption of the screened ore grinding medium is of the order of 2.5 pounds per kw.-hour, or less than 1 per cent of the tonnage of re-ground sulphides. IN RECENT years, there has been a considerable interest in pebble grinding in the uranium industry, and a number of installations have appeared. However, the use of sulphide ore pebbles as a grinding medium has so far been relatively limited. There has also been some question as to their suitability for the very fine grinding of sulphide concentrates. This paper describes the preliminary results of a commercial operation involving the

Jan 1, 1964

By Th. Hassel

The application of magnesium as an absorbable biomaterial demanded the consideration of the alloy composition, the mechanical properties and the corrosion a special adapted material development in terms of the human biological system. Magnesium for technical applications mostly comprised alloying elements up to 10 wt%. Thereby often metals (e.g. rare earth and aluminum) with high toxic potentials are used to optimize the mechanical properties. To minimize toxic reactions during the degradation of a absorbable magnesium alloy, the Mg-Ca system is being selected and investigated because both elements belong to the mineral nutrients. Rods and small tubes are produced by extrusion of gravity die casting billets (Ca-content 0.4 to 4.0wt%). The positive grain fining influence of calcium and its improvement of the corrosion behavior are additional advantages. The microstructure, the mechanical properties and the corrosion attitude are investigated. The results show that an optimal composition of micro alloyed Mg-Ca and ideally processing parameters lead to 16% strain and a tensile strength up to 185MPa. Electrochemical investigations and measurements of the hydrogen production demonstrate the influence of the Ca-content to the corrosion behavior of the investigated alloys.

Jan 1, 2006

By G. Knight

"Results of a program of dust research carried out at the Mines Branch Laboratory, Elliot Lake, indicate that dust-concentration estimates vary greatly, depending on the sampling instrument, the assessment technique and the properties of the dust cloud. The wide range of the ratio between the estimates by any pair of instruments shows that the correlation between the health hazard and dust-concentration estimates by most existing sampling instruments must be questionable. Important studies are being carried out to permit the definition of mine environments in more precise technical terms. The influence of size selection, the physical property measured, composition and sampling period on the assessment of the health hazard are discussed."

Jan 1, 1969

By J. A. MacLellan

"CONSTRUCI'ION OF SHERRITT'S CONCENTRATORSSherritt Gordon is operating two mills north of the 56th parallel, and is presently engaged in building a third. The author was closely involved in the design and construction of all three of these concentrators.The Lynn mill is the oldest of these three concentrators-it is a 4,000 ton per day nickel-copper plant built in 1953. The Fox mill is a 3,000 ton per day copper-zinc concentrator built in 1970. The Ruttan mill will be a 10,000 ton per day copper-zinc plant scheduled to go on line in July 1973.LYNN MILL The Lynn mill including the crushing, concentrating, drying and load out plant is about 69,700 square feet or 17.4 square feet per ton per day. '!his plant was originally built in 1927 at Sherridon, 150 miles south of Lynn Lake, as a 2,000 ton per day copper-zinc plant. In 1952 the plant was moved by tractor train to Lynn Lake. The whole plant was re-oriented within the original perimeter walls as a 2,000 ton per day nickel-copper plant. This plant was expanded to 4,000 tons per day by the addition of t1-Jo rod mills and a 5-1/2 short head crusher in 1959.The Sherridon mill processed its last ore in Sherridon in September 1951 and the first load of nickel concentrate was loaded at Lynn Lake on November 9, 1953 when the railroad arrived at Lynn Lake.The site for the Lynn Lake mill was cleared of overburden in the summer of 1952 and foundations for structural steel and SO!l8 equipment foundations were poured the late summer and fall of 1952 • Steel was erected from January to June 1953. Most of the equipment came in from January to March of 1953 by tractor sleighs. Sane sleighs upset but no equipment was lest through the ice."

Jan 1, 1972

By R. C. Wallace

Since the time when Canada's East and West were joined by the railway, and communication was established into the interior, settlements grew on the southern fringe of the great Precambrian area that formed the northern protaxis of the continent during its vicissitudes of growth. They clung precariously to the fringe of that ancient land, for the Precambrian is not generous to those who wish to live by the fruits of the soil, except in those limited areas where the Pleistocene ice-sheet has been profuse in its gifts of clay to cover the hard surface of the Precambrian rock. Later settlements spread westwards over the expanse of Cretacean plains that now form the wheatfields of the Canadian West; but there still remained in northern and western Ontario, in eastern and northern Manitoba, a pioneer race, to whom agriculture had attractions only in so far that it provided the wherewithal to lay siege to the riches of the Precambrian. And they had a vision beyond their time. More than they knew, they had seized the fact that for the complete rounding out of Canadian national life, a8 well as for the establishing of the necessary contributions towards the economic stability of Canada and its provinces, an industry in mining sh01.dd be well and truly built in the hinterland of the central provinces. Failing the winning of mineral from the rocks, and timber from the forests, there would remain between the East and the West an enormous barrier of unproductive country which would not only be an incubus to the agricultural people in their struggle for economic liberty, but would effectively, and for all time, remain an un-populated void across which the aspirations of East and West would be unable to unite.

Jan 1, 1924

By A. J. McLaren

Introduction Gold holds an important place among the mineral products of Manitoba. In value, it ranks second only to copper, which in 1931 attained first place. The gold production increased from 23,189 fine ounces in 1930 to 102,969fine ounces in 1931. The production for 1930, worth $479,359, came almost entirely from the Central Manitoba mine. The production for 1931 was worth $2,128,558, of which $1,509,018 came from the Flin Flon mine, $528,951 from the Central Manitoba, and $83,497 from the Sherritt Gordon. The Gem Lake mine and some prospects produced $7,785. The total output of gold in Manitoba, from the first recorded production in 1917 to the end of 1931, is estimated at 178,669 fine ounces, valued at $3,693,332. The production for 1932 promises to reach a new high record, due chiefly to the stepping-up of tonnage at the Flin Flon plants and the coming into production of the San Antonio mill in May. History The Manitoba Act, constituting Manitoba a Province of the Dominion, was passed in 1870 and provided for the vesting in the Crown of all un-granted or waste lands of Manitoba, as well as for the administration of these lands by the Dominion of Canada for the purposes of the Dominion "subject to, and except and so far as the same may be affected by, the conditions and stipulations contained in the agreement for the surrender of Rupert's Land by the Hudson's Bay Company to the Crown". Included in these waste lands were large areas later prospected and staked out as mineral lands. Up to the year 1912, that vast territory extending from the 12th base line to the 60th parallel of latitude, and from the Saskatchewan boundary to Hudson bay, was part of the District of Keewatin. Although added to Manitoba in 1912, the administration of its mineral lands also remained vested in the Dominion, so that all mineral lands within the Province upon which deposits of gold ore have been found were disposed of and administered by the Mineral Lands Division, Department of the Interior, until the transfer of the natural resources to the Province of Manitoba, on July 15th, 1930.

Jan 1, 1932

By B. D. Pandey, M. S. Kim, B. S. Kim

The recovery of Sn from used Pb-free solder (Sn, 3~4 % Ag, < 0.9 % Cu, < 1.2 % Pb) has been investigated by electrorefining in sulfuric acid solutions containing small amount of hydrochloric acid. This involved preparation of the anode material by melting and casting the used solder followed by refining. During electrorefining, dendritic tin was deposited on stainless steel cathode. Increasing the amount of hydrochloric acid up to 0.3 mol /L in the electrolyte enhanced the current efficiency to 92.2 % and the enrichment ratio of silver to 94.3 % in the anode slime which was otherwise 84.7% and 81.6 % in absence of HCl, respectively. The electrolyte containing hydrochloric acid has also prevented the precipitation of tin oxide in the bath. In the scale-up experiment using 1.6 kg anodes, 84.3 % current efficiency and close to 100 % Ag enrichment ratio were obtained, while the purity of electro-refined tin was over 99.9 %. The energy consumption of the winning process was found to be 0.151 kWh /kg-Sn which is competitive as compared to commercial tin electrorefining processes.

Jan 1, 2014

By J. G. Pearson, F. H. MacDougall, A. G. Galley

The difference in age, host rock lithology, alteration and style of mineralization indicates a fundamental difference in the format ion of gold deposits in the Flin Flon and Amisk Lake areas. The Flin Flon area contains early quartz-sulfide-gold veins fo rmed within intermittently active fractures and later plutonic hosted deposits thought to be generated in a porphyry system. In the Amisk Lake area two types of gold occurrences are recognized: I) gold-quartzcarbonate- sulfide veins within or flanking fault zones and 2) structurally and stratigraphical ly controlled zones of dissem inated and vein type sulfide-gold mineralization within extrusive and intrusive rhyolite and dacite porphyries. Both types of deposits are set within supracrustal rocks. are accompanied by intense alteration haloes and were formed prior to the major deformation event suggesting an early, epigenetic hydrothermal origin.

Jan 1, 1986

By Alfred C. Lane

WE recently received from Professor A. C. Lane, Emeritus Professor of Geology and Mineralogy, Tufts College, Mass., and a Corresponding Member of this Institute, a very interesting account of some recent developments in radioactive methods of determining the age of minerals and, therefore, of the rocks in which they occur. It deals in particular with studies of the minerals of certain pegmatite dykes on the Huron claims and Bear claims in southeastern Manitoba, which, the results indicate, are among the oldest rocks of the earth&apos;s crust. The following article presents a non-mathematical summary of Professor Lane&apos;s paper . . It will be noted that he is anxious to obtain suitable samples of certain minerals and rocks for further age studies. We hope some o our members may be able to supply him with the material he needs. It may be well to explain briefly how the age determinations are made. Uranium is continually breaking down, or disintegrating in successive steps through radium, etc., to a final product which is lead (uranium-lead), and the rate at which this change takes place is known. Minerals containing uranium will therefore contain lead also, and the lead-uranium ratio mul-tiplied by a certain factor (approximately 7 ,600) will give the age of the mineral in millions of years. Thorium also disintegrates at a known rate to give lead (thorium-lead) as a final product, and the age of a mineral containing thorium can thus be calculated from the lead-thorium ratio. Thorium breaks down more slowly than uranium. In unit time, one gram of thorium produces about as much lead as 0.36 grams of uranium.-ED.

Jan 1, 1938

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"At the moment climatic conditions are a primary problem of the exploitation of copper ore. The efficiency of preventive actions in order to improve climatic conditions is connected with the knowledge of changing air in underground excavations. This article demonstrates the analysis of types of ventilation dams which are used in sealing abandoned areas on the maintenance of climatic working conditions in excavations has been conducted at the exploitation in Polish copper ore mines. INTRODUCTION The basis for mining activity performed by KGHM Polska Miedz S.A. is mining copper ores from the deposit lying at depths between 600 and 1,200 m below ground level. Activity has continued since 1963. The copper ore deposit is mined in ‘Lubin’, ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines, where difficult climatic conditions occur. The major factor moulding the climatic conditions in headings is the original temperature of rocks, being the result of geological conditions of the lying of the deposit and the existing geothermal degree. In the faces of present opening-out and preparatory headings, driven from mining areas of ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines in order to open out deeper parts of the deposit, the original temperature of rocks reaches 45°C. Excluding the original temperature of rocks, the following are additional factors affecting the deterioration in the climatic conditions: • thermal properties of deposit rocks, • employed room-and-pillar mining systems, which are characterised by a large surface of exposure of rocks, • using self-propelled mining machines with diesel drive, • a high concentration of mining works, • setting up high-power electrical equipment in headings, • complex structures of mine ventilation networks, • a limited number of ventilating shafts, • constantly longer air-transport routes, • a significant accumulation of water increasing the humidity of supplied air. According to the valid Polish provisions (§21, 2013), the primary criterion of assessment of a climatic hazard is the occurrence at a workstation in an underground mining heading of an equivalent climate temperature of more than 26°C, which temperature is determined according to the following dependence:"

Jan 1, 2019

By Y. Guglielmi, C. Gout, P. Henry, P. Dick, C. Nussbaum

For a decade, observations and experiments conducted in underground environments worldwide (mines, underground research laboratories - URL) made it possible to bridge the scale gap between laboratory scale and large scale faults. Indeed, underground rock laboratories allow developing decameter scale relatively well constrained experiments at the smallest distance from the hypocenters. URL’s experiments allowed developing new monitoring technologies coupling pressure-strain-seismic measurements and reproducing complete earthquakes sequences analogous to natural ones. They also allowed exploring past movements of faults and sometimes also paleofluids in three dimensions and characterizing different fault architectures and hydromechanical properties in unaltered conditions. This is particularly important in the study of faults affecting clay formations which could not be observed at the Earth’s surface because of the high alteration. Here we show how examples from the Mont Terri (Switzerland) and Tournemire (France) The URLs may help in (i) defining the concepts of fault architecture in shales, (ii) estimating fault hydromechanical properties from field decameter scale experiments. Some key results are that faults which are critically stressed or at the rupture limit can reactivate for stresses variations within the range of those produced by shallow underground excavations, and that slight micrometer-to-millimeter scale reactivations may lead to large factor-of-10-to-1000 permeability increases. Such promising results show that URL’s experiments may bring new insights on some key processes that control the relations between fault stability and permeability evolutions in very permeable layers.

Jan 1, 2015

By K. Tarr

Acid-producing mine tailings are present at many active and inactive mine sites and pose an environmental liability due to the potential for acid rock drainage. Acid rock drainage originating from a tailings pile, a waste rock pile, or exposed sulfide-rich rock, can cause discoloration and turbidity in receiving waters, and the loading of ions mobilized by the acid can cause a decrease in aquatic flora and fauna, and reduction in the quality of groundwater. The primary cause of acid generation is the oxidation of sulfide minerals, predominantly pyrite and pyrrhotite. Considerable mine tailings are being stored on surface in vast tailings impoundment areas across Canada. In the tailings within this study, from the Sudbury, Ontario area, the sulfide mineral of primary concern with respect to acid generation is pyrrhotite. Different tailings types show varying and progressive degrees of oxidation correlating to their specific sulfur contents. The degree of oxidation is determined by the relative extent to which the sulfides have reacted as well as the depth of oxidation within the tailings. Natural Resources Canada, CanmetMINING is dedicated to research supporting the Green Mining Initiative, a program reducing business risks by demonstrating practices that reduce environmental impacts. In cooperation with the Canada Mining Innovation Council (CMIC), applied research aims to reduce land disturbance, waste volumes, and releases to the environment. By reutilizing tailings from vast impoundment areas as a component in backfill, the potential environmental impact would be lessened considerably, due to the reduced tonnage stored on surface long-term. From an operating perspective, there is a need for supplemental feed for backfill from time to time. The reclamation of old tailings for use in backfill is also driven by the fact that old tailings ponds may not be structurally stable, and it may be more cost effective to remove the tailings than to upgrade the impoundment structure. However it is imperative that these old tailings be fully characterized to determine their suitability for use underground, in order to ensure the long-term integrity of the resulting backfill matrix. A study was conducted to investigate the feasibility of tailings reclamation from old impoundment areas as a significant component in backfill. The materials were first physically and chemically characterized, followed by preparation of samples to determine optimal mix proportions for strength development for both paste and hydraulic fill compliance. It was found that the amount of oxidized tailings included in the backfill material had a profound effect on both the segregation and settling properties of the backfill matrix, as well as the mechanical properties of the samples. The strategies for decision-making, based on the criteria for material characterization, mining plan, and cost effectiveness are discussed.

Aug 1, 2013

By K. Turgeon, D. Larivière, L. Whitty-Léveillé, J. -F. Boulanger, C. Bazin

"The processing of ore containing rare earth elements leads to the production of an impure solution of these elements. The separation of the rare earths from the impurities and the production of individual elements is usually carried out by solvent extraction. The effectiveness of the extraction conditions and of the reagents is generally tested in the laboratory. This paper deals with the processing of results from solvent extraction laboratory tests planned to generate data redundancy. A method is proposed to take advantage of the data redundancy by accounting for the pH variation during the extraction. The parallel processing of several tests also allows estimating the equilibrium constants for the extraction. The proposed method produces equilibrium constants that are more reproducible than values estimated using conventional approaches. The method is illustrated with solvent extraction tests conducted on synthetic solutions of rare earth elements.INTRODUCTIONThe processing of ores containing rare earth elements (REE) usually includes the production of a concentrate of the minerals carrying the REE. These minerals, for instance monazite and bastnäsite, contain the 14 elements from La to Lu plus yttrium and scandium. As an example monazite has the general formula of (La,Ce,Pr,Nd,Sm,Eu,Gd,Tb,Dy…Lu)PO4 with a typical lanthanum content of 20-26%, cerium content of 40-50%, praseodymium of 4-6%, neodymium of 16 to 20%, and decreasing concentrations of heavier elements (Gupta & Krishnamurthy, 2005). During the processing of a REE mineral, it is generally not possible to isolate and separate a single REE from all the rest. The mineral molecules need to be broken (usually via a heat treatment followed by leaching with a base and/or an acid) to produce an aqueous solution of the REE of the ore. After purification of the solution, the REE can be precipitated as a bulk concentrate and sold to a refinery that separates the REE into particular groups of REE such as the light versus heavy REE or into individual elements such as lanthanum, neodymium, or europium oxides to yield value-added products."

Jan 1, 2016

By W. R. Hargrave

"Mining OperationsOre will be mined by open pit techniques. Because of the high grade of the deposit and the low strip ratio, mining rates are small relative to most other open pit operations.The ore deposit is located in the valley of the main fork of Red Dog Creek. The bulk of the deposit is located on the southwestern flank of the creek, but mineralization does traverse the creek in both the north and east directions.Erosion has exposed the orebody in a number of locations, and has resulted in oxidation of the mineralization closer to the surface. Although much of this oxide material is very high grade, it leaches readily and, at least in the initial phases of the operation, will be stockpiled and not treated in the concentrator.During construction, 2.3 million mt. (2.5 million st.) of overburden and waste will be stripped from the orebody to expose ore for initial operations. Competent non-mineralized waste will be used to build roads and waste dumps, but the bulk of material removed consists of oxide or ice-rich soils and weathered rock which is not suitable for construction.The annual ore mining rate will be 1.9 million mt. (21. million st.). The strip ratio will start off at 1.2 to 1, falling to 1.0 to 1 by year 5 and ultimately to 0.8 to 1.Bench heights are set at 7.6 m (25 ft). Pit slopes will vary depending on the material present in the wall. The slope, through competent waste and the sulphide package, was set at 45 degrees. This is flattened to 26 degrees (i.e. 2: 1) through overburden and Upper Kivalina shales. The Kivalina Shales are an ice-rich shale whose carbonate matrix has been leached out and which exhibits little or no strength as it thaws. In addition, a 100 ft containment berm will be left in the wall below overburden and Kivalina."

Jan 1, 1989

By Joo Hyun Park, Hyun-Sik Park

"Gold is one of the most valuable and precious metals. But, the extraction efficiency of gold from natural resources is very low and labor-intensive due to very low concentration of gold, i.e.,1–5 ppm, which means that gold extraction processes produce extensive amounts of tailings. The gold content in printed circuit boards (PCB) from waste mobile phones is about 100 to 400 ppm, which is enormously greater than the concentration found in natural ores. Consequently, processes for recycling waste PCB and gold mine tailings become of increasing importance to maintain a sustainable society. As processing these waste materials by pyrometallurgical methods has become more economically attractive, understanding the thermodynamic behavior of gold in smelting slags under oxidizing and reducing conditions has become increasingly important. Therefore, in this study, the effects of slag chemistry, oxygen potential and temperature on gold solubility in smelting slags are discussed. From the results presented, the predominant species of gold is strongly dependent on the basicity of slag. Furthermore, more basic slags showed higher solubility of gold at a given oxygen partial pressure, and more oxidizing atmospheres enhanced the dissolution of gold to the molten slag phase. As a consequence, careful control of the slag composition during pyro-processing of gold-containing waste materials is required to maximize gold recovery. INTRODUCTIONGold has good physicochemical properties. Thus, it plays an increasingly important role in industrial applications. For example, over 300 tons of gold are used annually in electronic components (Hageluken &Corti, 2010).However, 75% of all gold ever produced has been extracted since 1910 and gold reserves in the world are becoming rapidly depleted (Louis & Pluchery, 2012).The cost of gold production and its price in the market have increased rapidly during last 20 years as shown in Figure 1, and interest in the recycling of gold-containing materials has naturally increased.The wastes from electronic equipment (e-wastes) contain large amounts of precious metals compared to their own respective ores, and therefore such wastes may be considered as a secondary source of valuable metals. For instance, the concentration of gold in natural ore is commonly 0.5–15 g/ton-ore (0.5–15 ppm), while its concentration in electronic circuit boards is over 10 times higher, typically being about 150 ppm in expansion cards and over 10,000 ppm in central processing units(Barbieri et al., 2010).Also, gold mine tailings are discharged after the flotation process as slurry form then stored near the operating plants (approx. 100 ton per day in one Korean gold mine). Gold mine tailings contain gold at about 1–2 g/ton. This is the reason why Au-containing materials such as e-wastes and mining wastes are highly important sources of gold (Yamasue et al., 2009)."

Jan 1, 2017

By Jonathan Peck, Jim Gray

"With the implementation of more advanced monitoring, control and locating systems in surface mines, there is an ever increasing need for their mine-wide integration toward achieving over-all optimization. AQUILA Mining Systems Ltd. is developing the basis for a comprehensive real-time monitoring, control and information system called the Total Mining System or TMS. This system is being designed to address both current and future needs of open pit mines toward improving productivity and minimizing costs, through better two-way information flow between each component in the operation. At a basic level, feedback from equipment and process monitoring will enable decision making to be based on quantitative, on-demand information, thus permitting proactive rather than reactive planning. Dynamic planning would be a valuable tool as market conditions fluctuate, equipment fleets age and variations in the grade, quality, geometry and hardness of the mined material all contribute to either changing production targets or levels of achievable performance. Such a capability could be implemented within the next two years.At a higher level, and within five years, autonomous operation and/or real-time supervisory control of mobile and stationary equipment in open pit mines will be achieved. A discussion is provided in regard to the development and implementation of an autonomous haultruck and blasthole drill, to demonstrate the need for such a system.This paper outlines a preliminary program for the design, development and implementation of this system, primarily in relation to high-level communications and its role in the future automation of open pit mobile equipment."

Jan 1, 1995

By Laxman M. Amaratunga

"The fine fraction of tailings is usually excluded from the backfill process and generally disposed on the surface in tailings ponds. Because of the ever increasing demand for fine grinding in the extraction process for improved liberation of valuables in the ore, increased production of fines in the tailings has resulted. The negative impact of surface impoundment of tailings on the environment is well known. Amaratunga and Annor (1989) first presented a concept of fine tailings agglomeration for backfill.This paper presents the development of the novel cold-bond tailings agglomeration (CBTA) technology for non-reactive fine gold mill tailings. For cold-bond agglomeration regular portland cement was used as a binder. In order to cut costs, alternate binders such as lime, and blast furnace slag cement were examined. The effects of binder dosage, curing time, and agglomerate size on the fracture load strength of the agglomerate were studied.Fine tailings agglomerates are mixed with coarse tailings or non-agglomerated fine tailings to make high density fill compositions to be used as underground backfill. Alternatively, the agglomerates can be used as aggregates for surface applications. The paper discusses the environmental and operational benefits of this total tailings utilization and disposal technology.IntroductionIn Canadian mines, mill tailings are probably the most commonly used material for backfill. However, only the coarse fraction of tailings is desirable for use as hydraulic fill or high density fills. The fines are disposed on the surface in tailings ponds since they are unsuitable for underground backfilling owing to the following factors:i) slow settling ratesii) longer percolation timeiii) excessive consumption of binder due to drainageiv) poor compactionFor improved value liberation more milling operations have resolved to fine grinding in their comminution circuits. Gold milling operations driven by down stream leaching processes grind their ores excessively fine. In general, gold mines use hardly any tailings for backfilling. This can result in periodic short falls and the need to search for alternate backfill material from other sources. Apparently, the gold producers are the most identifiable sector which suffer from a shortage of backfill materials ( Amaratunga and Annor, 1989)."

Jan 1, 1994

By P. L. Drake

This paper comprises a discussion of the role which mineral resources will play in Canada&apos;s future export trade and the growing demand for minerals in Canada.

Jan 1, 1979

By T. P. Johnson, A. Vathavooran

"Conventional mining operations can produce a wide range of wastes containing gold and other precious metals but which are less suitable for processing by traditional methods. There are also types of ore that do not fit easily into a traditional processing flowsheet, e.g. because the refractory nature of their minerology or the combination of valuable metals is less suitable for traditional processes. Nevertheless, these potential sources of valuable metals remain unexploited resources that have attracted growing interest in the metals and mining industries over recent years. The challenge is therefore to develop and use alternative processing methods that have the flexibility of operation to cope with a wide variety of material types and tonnages, whilst providing high recoveries for valuable metals. Tetronics’ DC plasma smelting technology achieves industry-leading recovery rates for precious metals from a wide range of input materials and initial precious metal concentrations, whilst generating an inert slag-based material as a by-product (even when starting from a hazardous waste input material), approved within the EU for use in construction applications. This paper describes how this technology can be used as a key part of an overall process for the recovery of precious metals from these interesting materials.INTRODUCTION The extraction of gold from its ores by various forms of cyanide leaching has been practised by the mining industry for over a century (Minerals Council of Australia, 2005) and it remains the primary extraction method in a wide range of mining operations. The ability of cyanide to extract gold efficiently and quickly from lower grade ores without extensive additional processing, coupled with well-known methods to recycle the cyanide for re-use within the process mean it is often both the most economically preferable and environmentally acceptable method for recovering gold. As a result, 88% of all gold produced from mines in the USA in 2014 was recovered via leaching of open heaps or dumps (UGGS, 2016). Nevertheless, there are occasions where certain combinations of mineralogy and other circumstances reduce the effectiveness of cyanidation techniques, so that ever more elaborate additional processing steps are required, with inevitable increases in operating costs (Swash, 1988). In these circumstances, which are likely to be more common in future as ore qualities diminish, other methods of extraction may offer better alternatives. Whilst much less commonly used for Au extraction at present, pyrometallurgical methods are amongst the longest-established of these alternative approaches and merit serious consideration in such cases."

Jan 1, 2017

By D. C. Rance

"The Quintette Coal Limited property is located in the north east coal area of British Columbia. A basic agreement with the Japanese steel industry was ex ecuted on January 27, 1981 for the sale of 69.5 million tonnes of Quintette metallurgical coal over a 14.5-year period. This contract period can be extended by Jive years by mutual agree ment. Sale agreements have also been signed for the sale of 19.4 million tonnes of oxidized coal over a 15-year period. Work started on site development in the late summer of 1981, and at present, two of the four eventual pits-the McConkey and Frame-are under development. The pits are currently in a pres/ripping phase. These pits are notable for the stripping volumes that have to be removed from relatively small pit areas. in order to provide for the required detailed rapid short-range planning of these pits, engineering will be computerized, as will the truck dispatch system. The mining area lies 21.1 km from the plant site by road and the transport of raw coal LO the plant is by means of a highspeed conveyor system which has a total length of 13.4 km with a vertical drop of 740 m. The surface plant facility was designed on a modularized basis to facilitate maintenance, and is designed to enable the use ofgravity flow ofraw coal and heavy media in the plant to minimize the use of pumps. The construction of the plant and mine site facilities is on-going, and the first coal production is scheduled for early December 1983. Introduction Quintette Coal Limited is a Canadian company incorporated in the province of British Columbia in 1971. Denison Mines Limited is the manager of Quintette's activities. Equity in Quintette Coal Limited is held by several shareholders, with interests as follows: Denison Mines 'Limited, 500Jo; Charbonnages de France International S.A., 120Jo; and Japanese interest, 38%. The project will develop almost 120 million tonnes of coal for marketing during its first 20 years of production. All of the planned production tonnage has been committed to Japanese markets. Most of the coal will be metallurgical grade, and the remainder will be a high-quality thermal coal. The Mcconkey and Frame pits, which will initially provide the mine's production, will commence production in early December 1983 and will, in 1985, reach the full annual production of 5 million tonnes clean metallurgical coal and 1,380,000 tonnes of clean thermal coal."

Jan 1, 1985