Search Documents

By Joseph U. Messenger

A method of applying ammonium hydroxide to a drill stem containing hydrogen sulphide gas and hydro-gen-sulphide-bearing oil and water so as to remove the hydrogen sulphide as ammonium sulphide is de-scribed. It was concluded that the method allowed trips with drill pipe filled with sour fluids to be made more safely, more rapidly, and more economically. INTRODUCTION THE DANGER of poisoning rig crews during drill stem tests of sour wells by exposing them to hydrogen sulphide gas is well known in Canada. Concentrations of hydro-gen sulphide in sour gases range from 0 to 40 volume percent. There have been numerous casualties from hydrogen sulphide exposure during drill stem testing. Some have resulted in permanent injuries; in some cases the injuries have been fatal. For example, in Alberta in 1957 there were four deaths and 100 exposures which required medical treatment. These fatalities and injuries indicate the need for a more effective way of handling hydrogen sulphide in oilfield operations.

Jan 1, 1958

By Jianglan Duan, Steve L. Cockcroft, Andre B. Phillion, Carl Reilly, Daan M. Maijer

"In the aluminum alloy wheel casting process, careful design of the cooling system in the die and its operation (cooling channel timing) are critical to achieve quality and productivity goals. The problem is challenging owing to the cyclic nature of the process and the relatively large thermal mass of the die in comparison to the wheel. For a given die geometry, a set of constraints have been defined to ensure directional solidification and an objective function, based on cooling rate during solidification, has been defined to reach a target secondary dendrite arm spacing. The methodology presented in this study employs the commercial finite element package, ABAQUSTM, and an optimization module based on the open source library, Scipy. The developed methodology has been applied to a series of geometries and cooling system configurations, including a 2-D axisymmetric wheel and die assembly generated from a prototype die. Preliminary testing has shown that careful selection of the objective and constraint functions have made it possible to reach desired solidification pattern.TM- Dassault Systèmes Corp."

Jan 1, 2014

By Ruan Chi, Zhenyue Zhang, Zhengyan He

In order to understand what governs the leaching of exchangeable rare earth (RE) and impurities and enhance the RE leaching process, the effects of the concentration of ammonium sulfate, pH and leaching temperature on the migration of RE and aluminum (Al) during the leaching of weathered crust elution-deposited rare earth ore was studied. The elution curves for ammonium ion (NH4 +) were also studied to reduce the consumption of the leaching agent. It was found that a high concentration of leaching agent can enhance the leaching process of RE and Al, reduce the breakthrough volume of NH4 + and more rapidly obtain the equilibrium of NH4 +. However, excessive leaching agent can both increase the cost and the burden on the environment. There is almost no variation on the elution curves of RE and Al in the pH range of 4-8 and control of the pH of the leaching agent can be omitted. It is better for the leaching work to be done in summer since higher temperatures can enhance the RE leaching process and improve the use ratio of ammonium. Using 0.1 mol/L ammonium sulfate for leaching 250 g RE ore, 95.42% RE extraction can be obtained when the volume of leachate is 102.6 mL. At this moment, only 18.17% of NH4 + is used to exchange RE and 49.22% of NH4 + is left in the leachate that can be reused as leaching agent by replenishing ammonium sulfate. The results of our studies can provide theoretical guidance for high efficiency and low consumption exploitation of RE ores.

Jan 1, 2016

By J. Lipp

The lion share of lithium produced globally originates from South American salars. The standard operation for lithium production utilizes an array of evaporation ponds. This process consume vast areas and is either very slow when relying on solar evaporation - roughly 18 months of residence time; or with very high energy consumption since over 90% of initial water volume needs to be evaporated. A new technology, based on solvent extraction was developed. Results indicate a distribution coefficient up to 30, and selectivity greater than 1,000 towards Na extraction. The loaded solvent is stripped using a strong mineral acid, and the product solution is the lithium derivative of that stripping acid. Utilization of this new LiSXTM technology results in reducing the area needed for a commercial plant as well as reduces the residence time. In addition applying different stripping acids can diversify the product line of such facility.

Jan 1, 2014

By M. E. Coleman, G. Money

Pneumatic Conveying and Process Injection Technologies have been implemented in the metals markets for the last 40 years and have considerably improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider has turned its attention to supporting the Metals Market. Clyde seeks to utilise its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries.

Jan 1, 2008

By Jeanie Wills, Theresa Nyabeze, Samantha Espley, Donna Beneteau

This presentation reports survey findings that aim to modernize the definition and understanding of the term 'mining.' The survey, conducted via LinkedIn in Winter 2024, garnered responses from a diverse group of individuals, including current or former employees of mining or exploration companies, mining consulting firms, service providers, supplier firms, as well as students and retirees with industry experience. The data, ethically approved by the University of Saskatchewan, offers valuable insights into satisfaction levels within the mining sector and suggests an expansion of the identifying characteristics of definitions of mining. This marks the third CIM gaining insights paper by Beneteau, Espley, and Nyabeze, following previous works on 'Career Satisfaction for Women in Mining' (2010) and 'Mentorship Initiatives in the Canadian Mining Industry' (2018*)."

Oct 1, 2024

By L. H. Cole

FOR many years Industrial Minerals, or as they were formerly called, 'the Non-Metallic Minerals', compared with the metallics, were considered of only minor importance and as such were given scant attention in the technical press as well as in the public press. Those days are, however, happily passing, and thanks, to an appreciable extent, to the constant endeavour of the Industrial Minerals Section of this Institute, established in the fall of 1932 industrial minerals are now assuming the importance to which they are entitled. The term 'Industrial Minerals', when first adopted in this sense by the Institute, was thought to be original in its application, but it is interesting to note that it had been used many years previously by the Queensland Geological Survey in the following publication: SALT Article 1 in Industrial Minerals by B. DUNSTAN, Chief Government Geologist (Publication No. 268, in Part) Queensland Geological Survey, Department of Mines, Brisbane 1920 In Queensland, however, the term embraced some of the metals as well as the non-metallic minerals proper. The lead furnished by Canada in this matter bore rapid fruit, and already the term 'Industrial Minerals' is widely used, not only throughout Canada but in the United States as well.

Jan 1, 1939

By V. F. Hollister

Four conditions are commonly accepted as being needed for the development of native sulphur deposits in sedimentary rocks : (1) ample sulphate-bearing evaporite, normally anhydritic; (2) proximity to petroleum deposits; (3) a hydrodynamic system of communication between these two; (4) a stratigraphic or structural trap to prevent escape of the sulphur and sulphur -bearing reaction products. When any of these requisites are absent, apparently no significant residual bio-epigenetic sulphur deposit will form. These requirements are, however, satisfied in some areas, which include both the Triassic and Devonian evaporites of northeastern British Columbia.

Jan 1, 1977

By A. Bascetin

The mining industry in Turkey has been developing in the last 10 years. Mine wastes and tailings have thus been increasing, depending on the rising production rates. There are many problems related to accidents that occur in tailings damps. In this study, the applicability of the surface paste disposal (SPD) method for a Pb-Zn mine in western Turkey was examined. Density was 3.084 and specific surface area was 0.899 m2/g. The mill tailings have very low plasticity and show characteristics of clays and silts in terms of the Unified Soil Classification System. The particle size distribution of the tailings was 39.2% particles finer than 20 µm. The results of this study showed that the physical and chemical properties of mill tailings make them suitable for SPD.

Aug 1, 2013

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By M. H. MacLeod

"IntroductionTHE ORE PASS raise system at the H.B. mine as contracted by the Patrick Harrison Company consisted of two raises 6 ft. by 10 ft. in section •at 60 degrees to the horizontal. No. 88-88 raise, the longer of the two, was a straight raise 690 feet long, with access only from the bottom. In addition, this raise had two branch knuckle-backs only one of which was driven by. the Patrick Harrison Company. The other, known as 88-89 raise, was 540 feet long with knuckle-backs at 280 feet and 410 feet. Its access, also, was from the bottom (see Figure 1)."

Jan 1, 1954

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By K. S. Raja, F. Battick, B. Pesic

"CeO2 doped with lower valence cations, such as Y3+, Sm3+, Gd3+ etc. is considered as electrolyte material for low temperature SOFC. Doping introduces additional oxygen vacancies and improves ionic conductivity. This work describes the preparation of yttria-calcia doped-ceria precursor material, its sintering in DC and AC field methods, and characterization of sintered electrolytes with respect to the ionic conductivity. Doped precursor materials were prepared by a controlled co-precipitation process. Sintering of prepared, pelletized particulates was carried out using three different methods such as: 1) conventional; 2) spark plasma sintering; and 3) an alternating current field at 1125°C (AC assisted sintering). The mechanism involved in the conductivity improvement as a function of defect density, grain boundary area and phase stability will be discussed. INTRODUCTIONThe performance of SOFCs depends highly on the properties of materials. Subtle variations in the composition, microstructure, or density of SOFC components can considerably alter the power output capabilities of fuel cells. Early SOFCs utilized zirconia based electrolytes but efforts in lowering the operating temperatures of SOFCs have prompted investigations into several other oxygen ion conductors – often modified with dopants to either promote the formation of oxygen vacancies or to stabilize a vacancy rich high temperature phase – such as bismuth oxide, lanthanum gallate, and ceria.The transport of oxygen ions through the electrolyte first begins with diffusion into the material. While this is generally a surface kinetics phenomenon, it is safe to say that it is highly dependent on oxygen pressure and vacancy gradients. The role of the cathode in SOFCs is to reduce oxygen at the electrolyte surface creating an O2– ion gradient which induces permeation into the material. Once inside and under the influence of a potential field, O2– ions migrate by a vacancy hopping mechanism, Catlow, C.R.A. (1990), effectively exchanging positions throughout the matrix until they reach the anode and react, thus leaving the matrix."

Jan 1, 2012

By Xing-Liang Sun, Xian-Min Han, Zheng-Guo Zhu

The study on the material properties of frozen soils in China was being developed quickly in the past decades of years, because of the increase of the engineering constructed in frozen soil regions on the Qinghai–Tibet Plateau, and numerous research results were achieved mainly about strength and deformation behaviour and constitutive models of frozen soils. Studies have shown that the deformation procedure of frozen soils is irreversible; therefore, it is more appropriate to research mechanical properties of frozen soils by means of damage mechanics theory. In this paper, an elasto-viscoplastic anisotropic damage model is presented by introduction of Perzyna viscoplastic equation into analyzing the deformation of frozen soil. In addition, an anisotropic damage evolution equation is obtained by means of extending non-viscous damage to viscous damage. Triaxial tests at different strain rates are chosen to illustrate the application of this model, and good agreement between experimental data and numerically simulated results is obtained. The calculated results indicate that, under the same conditions, the damage at higher strain rate is less than that at low one. So the phenomena are explained from damage mechanics that the frozen soil has larger elastic modulus and shear strength at higher strain rates, and explained from mechanism that the emergence and development of micro-cracks in the body of frozen soil can be to some extent retarded at higher strain rates.

Jan 1, 2015

By J. B. Mawdsley

"AbstractThe uraninite-bearing deposits in the Charlebois Lake area of northeastern Saskatchewan are unusual and important concentrations of uranium. They were first discovered in 1949 and preliminary development work to the end of the 1951 field season indicates the probability that this will become •another uranium producing district. The deposits are in zones bordering granite masses. These zones are of migmatite (mixed rocks) composed of calcium-rich meta-sediments intruded and replaced by a fine-grained white pegmatite. Locally this pegmatite is replaced by an end fraction which is relatively rich in fine-grained disseminated uraninite; it is these occurrences that constitute the bodies of economic interest.The fine-grained white pegmatite contains plagioclase feldspar more lime-rich than that in the granites of which it is an end differentiate. This extra lime, evidently derived from the intruded sediments, would result in the raising of the temperature of crystallization of the pegmatite-forming magma, thus consolidating it rapidly near the granite contacts as a fine-grained pegmatite. The end liquor containing uranium was evidently locally concentrated in minor fracture zones in these pegmatites. Where no lime sediments were present. the coarse-grained alkaline pegmatites were formed. Their crystallization would not be accelerated and the uranium would tend not to be localized in the pegmatite but to migrate and consolidate at lower temperatures with the end products, possibly in some instances as pitchblende veins."

Jan 1, 1952

By W. McCombe, G. Remple, L. Zunti, M. Bernardin, L. Nightingale-Mercer

"The McClean Lake Mill is located approximately 700 kilometres north of Saskatoon, Saskatchewan, Canada and is operated by AREVA Resources Canada Inc. (AREVA). The mill was designed to process high grade uranium ores, and has been undergoing a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to processing high grade ores from the Cigar Lake Mine. During the metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit have a propensity to generate hydrogen gas during acid leaching. Hydrogen is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit. Uranium processing is further complicated by the fact that an oxidant in the form of oxygen gas or hydrogen peroxide is required to regenerate iron in the leach, which further increases the risk from hydrogen gas. During 2013 Hatch and AREVA designed and engineered a number of novel upgrades for the leaching circuit to mitigate the risk of hydrogen gas evolution in the process. Best in class technology was utilized in addition to control and operating strategy changes to ensure the leaching circuit can be safely operated with ores that can evolve hydrogen gas. This paper reviews the design concepts and modifications implemented on this unique and challenging project.INTRODUCTION The McClean Lake mill was originally designed to process high grade uranium ores, however until 2014 the average ore grade processed was 1%. The facility has been undergoing a multiyear upgrade and expansion to increase its production capacity from 12 to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to new high grade ores, averaging 18% U, from the Cigar Lake Mine. During the last round of metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit had a higher propensity to generate hydrogen gas during acid leaching than previous test work had indicated. Hydrogen gas is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit."

Jan 1, 2017

By Donald F. MacDonald

METAL PRICES RISE WITHIN the past nine months, the mining industry of the world has been revivified by a spectacular price advance for the metals. ln fact, practically all geological raw materials have been marked up during this period. Reviving industry started the price rise, but the armaments race among the nations has intensified it. These factors, coupled with our decided building shortage, which must be made up, will probably maintain metal prices at decidedly favourable levels over the next two or three years, or longer. OUR MINERAL CIVILIZATION It is interesting to recall that in the past hundred years, while the white population of the world increased some three ta three and a half fold, the consumption of minerals increased seventy-five fold. In other words, ours is a mineral civilization. If we disregard short slumps, which we will occasionally experience, it seems certain that the bread upward trend in mineral consumption will be maintained for many decades into the future. Nations without reasonably abundant and diverse mineral deposits will eventually become nations without much power. Canada is blessed with a splendid store of minerals. Its mineral industry is now facing an exceptionally rosy future. What of the mineral industry of Nova Scotia? GEOLOGICAL RESEARCH ALLOWED TO LAG RN NOVA SCONA Many years ago, when geological science was in? its infancy, much geological study was carried on in Nova Scotia. In 1827, Francis Alger began work on the iron ores in the Bay of Fundy region. In 1886, E. R. Faribault began his series of remarkable papers on Nova Scotia geology. Between these dates, many others published papers on the geology of the Province. The most outstanding of this early group of geologists was Sir William Dawson, whose published works on Nova Scotian geology extended over the period from 1845 to 1891.

Jan 1, 1937

By B. F. Haanel

IN the fall of 1929, a paper was presented at the Annual Western Meeting of the Institute entitled The Fuel Research Laboratories at Ottawa and the Scope of Their Investigations. At that time, the equipment of the laboratories had not been completely installed, but the regular routine work was being carried on as usual, and several large-scale investigations were being conducted. It is now five years since that paper was presented, and it seems fitting that a brief description of the investigations which have been undertaken, together with results-especially those which have reference to western Canadian fuels-be presented at this Annual Western Meeting. The coal mining industry of western Canada has, within the past few years, suffered many unfortunate vicissitudes. The replacement of coals by oil, for bunkering ships, for operating railway locomotives, and for heating, has weighed heavily on the coal mining industry of British Columbia and Alberta generally, but more particularly in the Crowsnest Pass area and Vancouver-and hydro-electric developments have also left their impress. With a full appreciation of these conditions, the Department of Mines planned research and large-scale investigations which it was considered would be of the greatest benefit to the coal industry, and the results have amply justified the plans and anticipations. The fact, however, must not be lost sight of, that the application of the findings of certain of these investigations would not have been feasible had not the Federal Government assisted the transportation of coal by the application of railway subventions. These subventions permitted Canadian coals to compete at competitive points with United States coals, and it must be admitted also in this connection that certain of the collieries which have benefitted, both as a result of the railway subventions and the investigations conducted by the Fuel Research Laboratories of the Department of Mines, made special efforts to produce a coal which was capable of competing with the American product, by special preparation at the mines.

Jan 1, 1936

By M. Mirnezami, J. A. Finch, S. Uddin

A fast, reliable and practical way of measuring zeta potential using sedimentation potential method is proposed. A cell was designed along with the instrument control software to determine the required variables simultaneously i.e. sedimentation potential, specific conductivity, volume fraction of solid as well as pH. High purity alumina and silica powders were used as test samples. Measured zeta potential using the proposed technique was comparable with the results by electrophoresis.

Jan 1, 2009

By A. S. H. Kabir

Due to the high specific strength and excellent corrosion resistance, Ti-6A1-4V has been widely applied in aerospace industries. In this study, the welding performance of 3.2-mm and 5.1-mm thick Ti¬6A1-4V sheets was studied using a 4 kW continuous wave Nd: YAG laser. It is found that the use of filler wire, matching the parent metal composition, can bridge the joint gap and produce full penetrated welds up to a width of 0.6 mm without cracking. The laser welds were characterized in terms of the bead geometry, defects, microstructures, and hardness. With increasing joint gap, the percent porosity area increased, reaching just over 1% of the fusion zone area at a gap width of 0.6 mm for the 3.2 mm and 5.1 mm thick sheets. The maximum underfill depth in the Ti-6A1-4V laser welds was about 5% or 7% of the sheet thickness for the 3.2-mm and 5.2-mm thick materials, respectively, meeting the AWS D17-1 specification. The microindentation hardness was maximum in the fusion zone and sharply decreased through the heat affected zone until reaching the base metal value.

Jan 1, 2011