Search Documents

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

By Tassos Grammatikopoulos, Sarah Prout, William Mercer, C. Gunning

"The Nechalacho rare metal deposit is located in NWT, Canada. Avalon Rare Metals Inc. is now evaluating processing techniques for recovery of REE to be used in the industry. QEMSCANTM analysis coupled with whole rock, REE, Zr and Nb, and electron microprobe analyses were utilized to identify and quantify the mineralogy of the deposit, and define the REE distribution among minerals. QEMSCANTM mineralogy was performed on fifty intact drill samples using EXPLOMINTM that provided textural information for the mineralization; crushed samples were used to determine the variability of the ore and define REE domains, and composite samples to determine the liberation and association of the REE minerals. The sample matrix predominantly consists of biotite, feldspars, quartz, muscovite/clays, minor chlorite and amphibole, magnetite and hematite and carbonates. REE include in decreasing order of abundance allanite (3.6%), monazite (1.5%), synchysite (0.9%), columbite (0.9%), fergusonite (0.6%), bastnaesite (0.4%), and zircon 11.0%. The majority of the HREE are carried by fergusonite and zircon, and the LREE by monazite, allanite, synchysite and bastnaesite. QEMSCANTM mineralogical data is extremely valuable in assessing the mineralogy of the ore. The data have been implemented in defining the mineralogy of the ore body, support metallurgical test work, predict recoveries and grades, and finally calculate reserves of the deposit.INTRODUCTIONAvalon is in the unique position of owning and developing one of the world’s largest rare earth deposits in the Northwest Territories of Canada.The term Rare Earth Elements (REE) is used to describe the 15 lanthanide elements or metals and, more recently, the metals yttrium and scandium, which display similar physical and chemical properties. REE are not particularly rare and have a similar abundance in the earth’s crust to nickel, tin or tungsten. Unlike these better known metals however, the rare earths have little tendency to become concentrated into commercial ore deposits. When they do become concentrated, deposits of REEs usually display enrichment in one of two groups. The most commonly occurring deposits of REEs contain a sub-group of elements referred to as the “light rare earth elements” (LREEs), which include lanthanum, cerium, praseodymium, neodymium, and samarium. Less commonly, deposits of REEs contain the much more valuable sub-group of elements referred to as the “heavy rare earth elements” (HREEs), which include europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium and lutetium. Yttrium and scandium most commonly occur in association with this second HREE sub-group. Generally, LREEs are produced from the mineral bastnaesite, and the HREEs have been produced from the minerals xenotime and monazite. LREEs continue to be produced from bastnaesite, however in the 1980s, China started production of HREEs from unique laterite clay deposits. China now produces approximately 95% of the world’s rare earths."

Jan 1, 2011

By J. E. Nesset, F. Rosenblum, J. A. Finch

"The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to highly reactive and potentially hazardous to both humans and infrastructure. It is essential that there be a reliable test methodology that can measure and categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral mixtures making it difficult to predict their self-heating behaviour a-priori based on mineralogy or with a simple “snapshot” test. Furthermore, self-heating behaviour will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to measure and reliably predict the latent self-heating hazard of a sulphide material. Several of the methods were tested and compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.INTRODUCTION Sulphides as well as other materials (coal, wood chips, hay, powdered milk, to name a few) that are stockpiled in an air atmosphere may undergo oxidation reactions which can result in the evolution of heat (Beever, 1984) (Hudak, 2002) (Blanchard, 2007). If the rate of heat generated exceeds the rate of heat dissipation, the stockpile temperature will rise, potentially leading to “hot spots” in the most reactive areas, and possibly even fires. The heat generation rate, the “self-heating” rate, depends on many factors such as the type and composition of material, particle size, moisture content, oxygen availability, ambient temperature and humidity, and of prime importance, the extend of prior oxidation, or more specifically, the presence of oxidation products. The desire of operators that mine, process or transport sulphide-bearing materials with a potential for self-heating is to have an accepted and reliable method for evaluating and quantifying the potential hazard of their material. The challenges are how to best measure the self-heating properties of given samples, and based on results, predict the behaviour of the bulk material over time and in-situ. Generally, when evaluating a given material one derives the self-heating characteristics of that sample at the time and under the conditions of testing, which will be referred to as a “snapshot test”. If that material is invariable, i.e. it will not change its response over time, then it may be considered to be a “predictive test”. However, if as a result of continuing oxidation or other changes, the material becomes more or less reactive with time, then a “snapshot test” is unreliable with respect to predictive ability."

Jan 1, 2014

By Jan E. Nesset, Antonio DiFeo, James A. Finch, Jose Hernandez-Aguilar, Cesar O. Gomez

"The gas dispersion measurement sensors and methodology developed by the mineral processing group at McGill University have to-date been employed at a number of plants in Canada, Australia, the U.S., South Africa and South America. In some cases the measurements have been directly linked with metallurgical performance while in others the gas dispersion surveys on their own have proved very useful in understanding the behaviour of the flotation cells. In addition to reviewing the current state of the gas dispersion measurement technology, the paper will present a series of case studies from the various plants and will show how this technology brings a remarkable new level of understanding to flotation behaviour. The influence of the bubble size distribution on recovery and grade are emphasized in the paper.INTRODUCTIONBackgroundThe advent of new sensors to characterize gas dispersion parameters in flotation cells is a development that is long overdue. While the chemistry of flotation has been studied since the early 1900’s, it is only now that the significance of bubble size distribution, gas rate and gas holdup can be meaningfully measured in-plant with robust and precise sensors. Early researchers, like T.A. Rickard (1916) recognized the importance of understanding the role of air and bubbles in flotation when he wrote in 1916 “we know that the key to the flotation process is to be found not in the oil, the acid, or the apparatus, but in the bubbles. The man who understands the mystery of a soap bubble has mastered the chief mystery of flotation”. In his 1999 review paper on The Froth Flotation Century D.W. Fuerstenau laments the fact that due to their “inert nature”, bubbles have never received their due attention from researchers who tended to focus on the chemical, physical, surface and colloidal aspects, rather than the physics of the process. It is perhaps fitting that now, 100 years after the inception of industrial flotation practice at Broken Hill, Australia, researchers and industry have turned their attention toward the importance of truly understanding the role of bubbles in flotation."

Jan 1, 2005

By Michael K. Watkeys, Charlesworth. E. GUY, Jacobus E. Potgieter, Anhaeusser. Carl R., Roger L. Gibson, Alexander F. M. Kisters

Abstract - Intrusive features of cupriferous noritoids from the deeply eroded Proterozoic granite-gneiss terrane of the Okiep Copper District in South Africa illustrate the emplacement of basic magmas into a mid- to lower-crustal environment. The small, easterly trending intermediate to basic intrusions of the so-called Koperberg Suite display a wide variety of geometries, occurrence and emplacement modes, including dike-, sill- and plug-like bodies. Coeval granulite-facies metamorphism, partial melting and ductile deformation of country rock gneisses during intrusion of the basic magmas led to emplacement and dilation processes of the intrusions which differ significantly from those described for dikes and sills at shallow crustal levels. Regional tectonic stresses are largely negligible due to very low differential stress (?1 - ?3) during deformation and intrusion, which permits emplacement at high angles to the principal compressive stress and which follows favorably inclined structural anisotropies. Dilation of the basic intrusions is largely determined by compositional differences of host rocks and occurs by thermal erosion, i.e., assimilation of wall rock gneisses. Low length-to-width ratios of basic to ultrabasic dikes and predominantly diaper -like outlines of mesocratic bodies are indicative of low viscosity contrasts between the mafic magmas and high-grade metamorphic host-rock gneisses. Buoyancy-controlled ascent of the basic to intermediate intrusions is expressed by a broad compositional zoning of basic bodies with respect to the granite-gneiss stratigraphy. Various intrusion modes within the stratigraphic column of the granite-gneiss sequence reflect a lithological and structural stratification of the seemingly homogeneous granite-gneiss terrane.

Jan 1, 1994

By N. R. Paterson, D. G. MacKay

"The geology of the Mattagami mining camp, while of particular economic significance, is unfortunately obscured by a very thick mantle of overburden. For this reason geo-physical methods have been relied upon heavily in exploring the area. Geophysical data over five important sulphide discoveries show how targets are selected for drilling and how effective geophysics has been in assisting subsequent development programs."

Jan 1, 1960

By L. W. T. Weitzel

"This paper reviews the Falconbridge- SMRQ’s Raglan project in northern Quebec and the process that was used in developing its current long-term mine plan. Challenges were many and not only limited to the longevity of the project, numerous ore deposits (both underground and open pit), and a 40 km property strike length. As a result of its remote northern location, other factors such as progressive reclamation, leachable mine waste, water treatment, and waste management were also part of the plan. A combination of modern planning tools were used to formulate the plan including DataMine, Mine 2-4D, AutoMod Simulation, and an Excel-based financial spreadsheet to bring the total plan together. The focus of the paper is to show the complexity of modern mine planning and associated economic modelling of mine processes. IntroductionThe Raglan project is located 1660 km directly north of Quebec at the northern tip of the Quebec Peninsula in Nunavik. The main property is 40 km in length stretching from the Donaldson airport area at the eastern edge of the property to East Lake at the western edge. The Deception Bay port is 90 km north of the main complex/mill situated at Katinniq which lies approximately in the middle of the property (Fig. 1). The mine processes 1 000 000 tpy of ore from both open pit and underground sources. The mill is forecasted this year to produce more than 150 000 t of concentrate grading more than 18% nickel. All personnel and critical cargo are transported to the site via a company-leased 737 jet from Rouyn-Noranda where the main administration office is located. The majority of cargo is shipped to the site via Deception Bay from Quebec and on the return trip, nickel concentrate is shipped back. From Quebec, the nickel concentrate is sent by rail to the Falconbridge smelter in Sudbury and on the reverse rail haul, nickel matte from the smelter is sent to Norway via Quebec."

Jan 1, 2003

By Jason Clarke, André R. Laplante

"The gravity-recoverable gold (GRG) ore characterization test was developed 15 years ago and has been applied to hundreds of ore samples. The test accurately determines the size distribution of GRG, at which grind it is recoverable, and the extent of its liberation above 150 µm. This contribution shows how the test can be simplified, what are the likely problems to occur, and what information is then lost. Two simplified versions of the test are presented, of which the simplest, grinding a 20-kg sample to a P80 of 75 µm, is retained as the best one. A database of 18 comparative tests is presented. The choice of the full GRG test vs. the simple test is discussed, as is the deportment of the GRG recovered in the standard test but not in the simplest test.INTRODUCTIONThe GRG test was developed in 1990 to characterize the progressive liberation of gold in representative samples of ores, with the primary objective of generating data for a gold gravity recovery model (Woodcock and Laplante, 1993; Laplante et al., 2000). Characterization includes the size distribution of GRG as well as the grind size at which it becomes recoverable. This is achieved in a 3-stage protocol of liberation and recovery using a laboratory centrifuge unit, a Laboratory Knelson Concentrator 3 inches in diameter (KC MD3). This protocol is shown in Figure 1. The first stage takes place at a F100 of 850 ?m (F80 of ~550 ?m), the second at F80 of 180 ?m, and the third at a P80 of 75 ?m. The rationale for the three cycles is the desire to preserve the original size distribution of the gold grains in the ore and to obtain a recovery grind size curve. The feed is a representative sample of ore that can be extracted from ore samples (e.g. drill core reject) or stream products of the grinding circuit other than circulating loads or product having undergone hydraulic classification (e.g. rod mill discharge or SAG screen undersize). Ideally the samples should weigh between 60 and 100 kg, depending on feed grade and gold top size. It is beyond the scope of this paper to fully discuss measures of representativity in the ore sample, for example Gy’s minimum sample mass model (Gy, 1979). However, further work in this regard may be an opportunity. The large initial weight facilitates representativity and minimizes weight and sulphide recovery to the concentrate (since concentrate weight is relatively constant at ~100 g), which limits the recovery of gold in nonsulphide gangue or gold carriers (i.e. sulphides). Thus, the 100 g concentrate carries principally discrete gold species, such as electrum, and native gold. The concentrate and a 600-g representative sample of gangue of each stage are screened down to 20 ?m and each size class is fire assayed (the concentrates to extinction, the tails up to 30 g per size class). The five coarsest size fractions of stage-1 concentrate are individually upgraded using a hydrosizer and the concentrates examined with an optical microscope to assess the degree of liberation of the gold phase. Scanning electron microscope work has established that the GRG has an excellent degree of liberation below 150 ?m in stage 1 and generally a good degree of liberation in stages 2 and 3 (Guerney et al., 2003); as a result the size distribution of the GRG has been found to approach closely that of gold grains (Nesset et al. 2005)."

Jan 1, 2006

By Jean Rosaire

?GWIOP Location ?Climate and Physiography ?History ?Geology ?Deposit Types ?Mineralization ?Historical Mineral Resources ?Conclusions and Work Program

May 1, 2007

By I. Campbell, P. C. Jones, E. G. Potter, R. P. Taylor

"The Cobalt embayment is a large domain of Paleoproterozoic clastic sedimentary rocks that unconformably overlies the Archean Abitibi greenstone belt. Regionally extensive sills and dikes of Nipissing diabase, emplaced circa 2219 Ma, occur throughout the embayment and are the preferential host to gold-bearing polymetallic vein systems on the Merico-Ethel property, near the northeastern margin of the Cobalt embayment. These gold-bearing, polymetallic veins are predominantly east-west-trending, steeply dipping, discordant calcite- quartz vein systems that formed close to the time of crystallization (within ~15 m.y., based on Pb-Pb ages) of the Nipissing diabase. The ore mineralogy is complex in character, typically comprising sulfides, arsenides, native metals (gold and silver), and specular hematite, preferentially concentrated along the interface between silicate and calcite gangue. A simplified sequence of mineral deposition in the veins is: (1) "Early-stage" pyrite ± chalcopyrite hosted in quartz ± chlorite gangue; (2) "Main-stage" polymetallic (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U) sulfides, arsenides, and native metals hosted in calcite gangue; and (3) "Late-stage" calcite flooding ± galena. Wall-rock alteration in Nipissing diabase is restricted to narrow (<5 cm) haloes of calcite-chloriteepidote- bearing assemblages, whereas a weak alteration halo of specular hematite, calcite, and allanite-epidote has been observed in the surrounding sedimentary rocks. In terms of their age, geology, mineralogy, paragenesis, and morphology, the gold-bearing vein systems at Merico-Ethel closely resemble the silver-sulfarsenide vein deposits of the historic Cobalt and Gowganda mining camps. These observations indicate that the Au-bearing veins are variants of the Ag-vein systems and as such, have a common genesis belt. L’Échancrure de Cobalt est un large domaine de roches sédimentaires clastiques d’âge Paléoprotérozoïque qui reposent en discordance sur la ceinture de roches vertes d’Abitibi d’âge Archéen. La Diabase de Nipissing, mise en place vers 2219 Ma et qui constitue un réseau de sills et de dykes d’importance régionale, est présente dans l’ensemble de l’échancrure et constitue la roche-hôte principale des systèmes de veines aurifères-polymétalliques de la propriété Merico-Ethel, près de la bordure nord-est de l’Échancrure de Cobalt. Ces veines à minéralisation aurifère et polymétallique constituent un système de veines de calcite-quartz sécantes d’orientation principalement est-ouest et à pendage fort qui se sont formées peu de temps après la cristallisation de la Diabase de Nipissing (à ~15 Ma près, d’après les âges Pb-Pb). La minéralogie de la minéralisation est complexe; elle consiste typiquement en sulfures, en arséniures, en métaux natifs (or et argent) et en hématite spéculaire, préférentiellement concentrés à l’interface entre les silicates et la gangue de calcite. La séquence de déposition simplifiée des minéraux dans les veines est : (1) «Stade précoce» pyrite ± chalcopyrite encaissés dans une gangue de quartz ± chlorite; (2) "Stade principal" sulfures polymétalliques (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U), arséniures, et métaux natifs dans une gangue de calcite; et (3) "Stade tardif" calcite massive ± galène. L’altération pénétrative de la Diabase de Nipissing est confinée à des halos étroits (<5 cm) présentant des assemblages marquées par la présence de calcite-chlorite-épidote, tandis qu’un faible halo d’altération en hématite spéculaire, calcite et en allanite-épidote est noté dans les roches sédimentaires environnantes. De par leur âge, leur géologie, leur minéralogie leur paragenèse et leur morphologie, les systèmes de veines aurifères de Merico-Ethel ressemblent beaucoup aux gîtes filoniens d’argent-sulfoarséniures des camps miniers historiques de Cobalt et de Gowganda. Ces observations indiquent que ces veines aurifères constituent une variante des systèmes des veines argentifères et qu’elles partagent"

Jan 1, 2009

By James L. Oleson, Hunter R. Propsom, Kevan J. R. Ford, Robert D. Henderson, Bob Musgrove

"Kinross’ Fort Knox Gold mine, near Fairbanks, Alaska has successfully implemented two major metallurgical continuous improvement projects resulting in growth of gold production and an extension of mine life. In 2009, Fort Knox produced 263,153 oz of gold at a cash operating cost of $543/oz. In 2010, approximately 63% of the gold will be produced from the CIP circuit, 15% of the gold from the gravity circuit and 22% of the gold from the heap leach.In 2009, a 44,000 ton per day run-of-mine valley fill heap leach facility was constructed and commissioned as a cost effective treatment option for low grade ores to supplement the higher grade mill. The heap leach facility will produce approximately 100,000 ounces of gold per year under severe winter conditions. Heap leach gold recovery, based on test work shows 30% after a 55-day leach cycle, with long term ultimate gold recovery targeted at 65%. The paper presents the heap leach design concepts and production data.Additionally in 2009, installation of a Knelson gravity concentrator unit (XD70) was completed. This together with an Acacia intense leach reactor (AILR) has increased overall mill gold recovery from 79.3% to 80.7%. A manual shaking table gold recovery operation has been replaced by batch intensive cyanidation of the high grade Knelson concentrates. Increased removal of coarse gold and difficult-to-leach gold species from the grinding circuit, via the gravity circuit, has improved gold leach recovery in the conventional whole-ore tank leach CIP circuit. The paper presents plant operating data, showing the improvements over the old flowsheet.Focus on the metallurgical properties of the high grade and low grade end components of the Fort Knox ore has resulted in significant improvement to gold recovery."

Jan 1, 2011

By R. J. C. MacDonald

"The first recorded discovery of placer gold in Canada was on the Chaudiere River in Quebec's eastern townships in 1832 and the first major production came from placer deposits in British Columbia in 1858 (Verity 1974). Placer deposits were the major source of gold until the late 1890's, although lode deposits were found in Nova Scotia in 1862. In 1896 the Klondike Gold Rush commenced with the discovery of gold by Henderson and Carmack in the Yukon. The peak was reached in 1900 when over one million ounces of gold valued at approximately $22.3 million were recovered. With the exhaustion of the easily accessible deposits, more capital intensive operations were necessary such as those initiated in 1906 by the Yukon Gold Corporation. This giant dredging operation continued to produce until 1966. Today only a few small operations remain.The development of Canadian lode gold mining began in earnest around 1900 when the railroads were opening up the interior and western part of the country. At this time many discoveries occurred, particularly where mineral outcroppings were near surface. Tremendous impetus for exploration and the reopening of former producers followed the elimination of the gold standard by Great Britain around 1931, and more importantly the United States in 1933, with subsequent stabilization of the price of gold at $35 per ounce in 1934. Prior to this the price of gold was basically unchanged since 1717, approximately, $20 per ounce (Verity, 1974; Green, 1973).The depression of the 1930s adversely affected most industries, however for the gold producers it was a very profitable time. Prices of materials and equipment declined and labour was cheap and plentiful. Interest in gold mining was further stimulated in 1936 when a three year tax exemption was declared for all new metal mines. In 1938 a decline in the value of the Canadian dollar relative to the U.S. dollar benefitted the industry. The second world war provided yet again further incentive for gold production and in 1941 Canadian gold production reached a high of approximately 5.4 million ounces. This figure was not surpassed until 1991 when approximately 5.6 million ounces were produced (Natural Resources Canada, 1996 )."

Jan 1, 1998

By Malcolm Powell

"The argument has long raged across the oceans as to what the best AG/SAG mill aspect ratio is. The North American practice of a high aspect ratio of two, diameter twice length, through to the South African and Scandinavian practice of an aspect ratio of as low as a 0.5. Within the collaborative P9 AMIRA project the MPRU of the University of Cape Town and the JKMRC of the University of Queensland have been collecting plant data pertinent to this issue over the past four years.The JK SAG mill model developed by the JKMRC is based upon data collected from mills having a range of aspect ratios from 1 up to 2. The maximum mill speed, mill load, and ball filling in the fitted data base were all below the operating range common in South Afr-ica. The extension of the P9 project into South Africa therefore lent an ideal opportunity to collect data in a whole new window of operation that would allow the range of applicability of the semi-empirical SAG model to be greatly extended.At the heart of the differences in aspect ratio is the completely different operating practice for high- and low- aspect mills. The mill filling, mill speed, and recirculating loads of closed-circuit single-stage operation have more influence on the differences in operation than the pure aspect ratio relationship. Relationships for load have been extended to 45% filling, with the modified model showing the measured peak in throughput as the mill filling increases. The ball load relationship now covers fillings of over 30% balls (of total mill volume), thus including so-called SAG-ball mills. The influence of closed circuit operation has been measured. It has been found that a key issue of the high slurry flows associated with closed circuit operation, especially when closed with a cyclone, is the pulp discharge limitation of the traditional grate and radial lifter configuration. It has also been observed that absolute mill length is more of an issue than aspect ratio. Slurry flow along the mill and charge segregation within the load are being investigated on pilot and full-scale mills to provide data for potentially modifylng the perfect mixing model that is used for the SAG mill.Improved understanding of these aspects of SAG mill operation and extension of the JK SAG model to better cover the entire range is allowing serious direct comparison of high- and low aspect mills for the first time. It is the conclusion of the researchers working in this area that there is no one best practice, that in fact mills across the range have their application based on ore type, desired product, available capital and on operating costs. Developing robust designs allows direct comparison of two-stage circuits using high-aspect primary SAG mills, with single-stage closed circuit low-aspect SAG mills. The new operations within South Africa are now considering both circuit types, and data is presented on selections that cover the full range of aspect ratio and operating practice."

Jan 1, 2002

By Roussos Dimitrakopoulos

Conventional approaches to estimating reserves and optimizing mine planning and production forecasting result in single, often biased forecasts. This is largely due to the non-linear propagation of errors in understanding orebody attributes from a limited finite number of drilling data, throughout the chain of mine planning and mining. A new mine planning paradign is considered herein to include two interacting and potentially fusing elements: stochastic simulation and stochastic optimization. These two elements provide an expanded mathematical framework that allows the modelling of orebody uncertainty and its direct integration to mine design, production planning and valuation of mining projects and operations. This stochastic framework has shown to increase the value of production schedules in the order of 25%. In addition, case studies show that stochastic optimal pit limits are about 15% larger in terms of total tonnage, compared to the conventional (deterministic) optimal pit limits. This difference extends life of mine and adds approximately 10% of net present value (NPV) to the NPV reported above from stochastic production scheduling within the conventionally optimal pit limits. Furthermore, results suggest a potential new contribution to the sustainable utilization of natural resources.

Oct 1, 2009

By K. Leung, J. E. Udd, L. B. Geller, F. Kitzinger

"Sixteen miners died tragically at the Paymaster gold mine in Timmins, Ontario, in February 1945 when a badly corroded hoist rope broke. The investigation of the Royal Commission that followed arrived at a number of recommendations (The Legislative Assembly of Ontario, 1947) aimed at avoiding future disasters of this kind. One consequence was the development and legislated use in Canada, several decades ago, of powerful electromagnetic (EM) instruments for the non-destructive testing of mine shaft wire ropes. The authors have been involved for many years in the design, production, and testing of EM instruments (Geller and Udd, 1990, 1992; Geller and Kitzinger, 1991; Geller et al., 1992). Since the mid-1990s, particular attention was paid to the design and operational results obtained from the computer controlled portable MagnographTM II wire rope tester (Geller et al., 1995, 1998).In the present paper, the authors summarize further hardware- and software-related developments of this instrument. Further, an account is given of the results obtained from the most recent design known as the Perma- ScanTM testing system. This is also a computerized dual-function system. In it, however, the sensor head is designed primarily, if not solely, for permanent installation and for remotely controlled operation. This represents a basic departure from traditional designs, which were intended for ad hoc temporary installations. The remote-controlled instrument described in this paper has now been in operational use for more than four years."

Jan 1, 2003

By R. Amelunxen

"The molybdenite associated with copper porphyry ores is generally treated in a flotation circuit consisting of a separation and a cleaning section. In the last few years column flotation cells have replaced the numerous counter-current stages that were previously used in the cleaning section. Despite this, little has been published regarding the number of column cleaning stages required. Therefore a Moly flotation database is assembled with the objective of verifying the existence of a common upgrading profile. This can then be used as a guide in the prediction of the number of stages required to achieve a given concentrate grade.INTRODUCTIONAlthough the first use of Column Flotation was on copper flotation products, the popularity and understanding of their operation was not really achieved until they were widely implemented in Moly circuits in early 1983. The use of columns in Moly plants has since left a legacy of information, both published and unpublished. The data collected since that time has been used primarily used to establish column operating parameters and to determine upgrading potential within the circuit.Byproduct Moly generally occurs with porphyritic copper ores in concentrations less than 0.1% MoS2. As such, piloting a new moly ore to produce, say 5 Kg/Hr MoS2, in a slurry approximately 1 Lt/min (at 10% solids), requires a moly plant feed of about 570 Kg/Hr, which translates to a mill feed rate of 200 to 800 Tonnes per day (depending whether you deal with Chilean or Canadian ores). Piloting Moly for any lower tonnage would reduce the accuracy of the testwork.Thus a need exists to collect operating data in order to establish the existence of process relationships that could be used for feasibility and design purposes.The object of this paper is to expose a preliminary relationship that could be used for the purposes described above and to apply the findings to a preliminary design of a moly cleaning circuit flowsheet."

Jan 1, 1990

By J. Gotor, C. Frias, E. Delgado

The Iberian Pyrite Belt (IPB) is one of the world&apos;s largest reserves of primary sulphides containing base metals (Cu, Zn, Pb), precious metals and some special metals such as indium. Estimated resources are over 1,500 million tonnes of volcanogenic massive sulphide ores. From 1980´s Europe lives the decline in its mines mainly motivated by the low price of the metals. One aspect that contributed equally to this was the ecological disaster produced by the discharge of more than seven million tonnes from the tailings dam of Boliden-Apirsa (Aznalcollar) in 1998. Today the situation is different; the companies present in the IPB have given evidence that it is possible to reconcile mining projects and care on the environment, and the regional authorities are opening a public tender to re-start Aznalcollar mine. A new challenging era has been started at this Spanish/Portuguese mining area. This paper presents the results and preliminary economics of a project devoted to IPB primary sulphides processing through different technology approach, e.g. conventional selective flotation against bulk flotation or mixed metals flotation combined with hydrometallurgical processing.

Jan 1, 2014

By P. Miranda, K. Le, G. Maes, R. Peters

"The Mount Milligan Mine, owned by Thompson Creek Metals Company Inc. (TCM), started operations in September of 2013. It is located between the communities of Fort St. James and Mackenzie and is the first major metal mine to open in British Columbia in 15 years. Based on reserves as of January 1, 2014, it has an estimated 22 year mine life with 2.1 billion pounds of copper and 6 million ounces of gold in reserves. Like all commissioning operations, there have been issues achieving design throughput and recovery due to flow sheet design, equipment failures, control philosophy, and reagent scheme. Efforts to improve overall mill performance include equipment modifications, reagent screening and testing, and grind size testing. Applying these changes to the mill and working closely with the mine has resulted in continuous improvement each month as Mount Milligan looks to achieve the nominal design capacity of 60,000 dry metric tonnes per day in the later part of 2015. Considerable focus is being placed into ensuring size reduction equipment is utilized effectively. Additional modifications and tests are being undertaken to steadily improve processes and alleviate restrictions in the mill. This paper will discuss the start-up and present ramp-up history of Mount Milligan, the current mill processes, and the steps taken to achieve expected production numbers.OPERATION BACKGROUNDMount Milligan is an open-pit copper and gold operation wholly owned and operated by Thompson Creek Metals. It is located approximately 155km northwest of Prince George, British Columbia, between the communities of Mackenzie and Fort St. James. The copper-gold porphyry deposit contains a Measured and Indicated Mineral Resource of 706.7 Mt at 0.18% Cu and 0.33 g/t Au, containing 2.84 billion lb. copper and 7.50 million oz. gold. Mine life is currently estimated at 22.1 years (“Feasibility Update – Mt. Milligan,” 2009). The mill is designed to process 60,000 dry metric tonnes per day and produce 400 dry metric tonnes of concentrate per day averaging 25.5% Cu and 40 ppm Au. Concentrate is delivered by truck and trailer to Mackenzie followed by rail to Vancouver for overseas shipping to various customers.Mount Milligan is considered a “zero discharge” operation meaning no process or surface water will be discharged to the environment. As well, stockpiling is very limited and is only permitted for a short period of time. This scenario presents several unique challenges. Scheduling of ore/waste production must be carefully planned as waste rock is used to build the tailings storage facility (TSF). Reagent selection is also important as persistent chemicals will have a tendency to build up in reclaim water which feeds the process water tank."

Jan 1, 2015

By Mark G. Lafontaine

Underground 802.11 wireless communications has become widely adopted for automation and communication purposes but maximizing the wireless signal presents many obstacles given the harsh environment as well as the presence of materials and conditions that can reduce signal propagation. Changes in elevations and curvatures in ramp to drift transitions also affect the wireless signal. Based on the requirements of wireless applications such as voice, data, or location tracking, the wireless site survey is the key tool for measuring and predicting signal strength and signal-to-noise ratio. These readings help determine the maximum distance between access points in order to sustain an overlapping wireless signal where required. This paper describes the methodology and tools used for measuring 802.11 wireless signal strength in an underground mine environment in Northern Ontario. The physical characteristics of the mine and the actual recorded wireless signal data will be presented in order for the audience to gain an understanding of the factors that affect signal throughput. Antenna selection used for the site survey will also be discussed as it played a key role in propagating the wireless signal.

May 1, 2013

By R. G. Burn

"A brief outline will be given of the concept of risk and its implications with regard to investment in exploration. The relationship between risk and decisions under uncertainty will be examined as a prelude to identifying those factors which contribute to exploration risks:consideration of the effects of corporate objectives (e.g. survival, expansion, diversification) on exploration strategy and ultimately on success or failure, exploration and mining as an investment (the relationship between risk and reward) and the desired return on investment; exploration odds, funding levels, staying power, financial exposure and the concept of gambler&apos;s ruin;origins of uncertainty in exploration decision-making-man-made risks and natural hazards; the nature of introduced constraints at each exploration decision stage and their effect on the rate of success;improving the chances of success and the invest reduction of risk through sound exploration strategy, effective project generation and efficient target detection capabilities."

Jan 1, 1984