Search Documents

An extensive series of tests was carried out on a ball mill-rake classifier circuit in the New Broken Hill Consolidated Ltd. concentrator. The data were used to develop a mathematical model of the operation of a rake classifier and this model has been used in the simulation of the performance of a ball mill-rake classifier circuit on a digital computer. As a result of this simulation it has been possible to develop a technique for the optimization and control of a circuit which includes these units.

Jan 1, 1967

A BRIEF DESCRIPTION OF TELPHER HANDLING AND BLAST FURNACE EQUIPMENT.The various sections will be described in the following order:(a) Telpher Handling and Storage Bins.(b) Blast Furnaces.(c) Slag Disposal.(d) Bullion Handling to Drossing Kettles.(e) Copper Drossing.(f) Copper Matte Furnace.(g) Bullion Delivery to Refinery.(h) Fume Handling.(a) TELPHER HANDLING.The telpher installation is an all-steel structure designed to carry out the work of assembly and delivery of charge materials to the blast furnaces.To simplify description, the primary telpher installation will be divided into three (3) sections:-No. 1 Section. 395 ft. long, running north and south, parallel to the water front, and so located that coke, which...

Jan 1, 1937

Wetting Characteristics of Mineral Surfaces - Contact Angle Measurements through Molecular Dynamics Simulations

Sep 13, 2010

The great problem at Port Pirie and many other lead smelters has always been to keep the lead content of the slags down to a low level. This has been done in the past largely by empirical methods, the lead content varying from less than 1 per cent to over 4 per cent, the more usual figure being something under 2 per cent. Subsidiary to this, but of major importance in the future, was the extraction of the considerable quantities of zinc in the slag. At this stage little was known about the constitution of the slags apartfrom their chemical composition. Some early work on slag constitution was carried out in the B.H.A.S. Research Laboratories between 1919 and 1921, but except for a microscopic examination of a few thin sections the greater part of this investigation wasdevoted to the recovery of the zinc content of the slag by leaching methods.In 1949, therefore, it was decided to initiate a programme of fundamental research into the constitution and properties of the lead blast furnace slags. The information thus gained would give a clearer picture of reactions taking place in the slag, both in the blast furnace and during dezincing.There was also the hope that these results would lead to improved industrial techniques resulting in smaller lead losses, and, taking the long-term view, to efficient methods of producing zinc from the slags.A series of investigations was therefore begun at various centres over a period of time. These were:1. A mineralogical examination of the slags by Dr. A. B. Edwards of the Mineragraphic Section, C.S.I.R.O.2. A study of the thermodynamics of various slag com...

Jan 1, 1956

By Conochie D. S, Grave N. C

Disposable-tip emf cells at present used in liquid steel can be used to measure the state of oxidation of high-iron slags produced in non-ferrous smelting. This provides a new tool for the control and evaluation of pyrometallurgical operations.An investigation of oxygen potential variations throughout a typical nickel smelter using the flash smelting technique gave a valuable insight into the process. Correlations of oxygen potential with ferric to ferrous oxide ratio and nickel content in slag were in reasonable accord with equilibrium data in the literature indicating that the probes may be used both as a plant investigation tool and possibly as a means of obtaining thermodynamic data for slags.

Jan 1, 1979

By Holdgate G. R, Thompson B. R, Webster R. L, Bolger P. F

The Gippsland Basin in south-eastern Australia has an area of approximately 46 000 sq km. It is one of the world's major coal and petroleum bearing basins, with most of the former occurring in the smaller one fifth on-shore part. The stratigraphy, structure and economic resources of the Tertiary sedimentary pile is now well known through extensive drilling for coal and petroleum. In contrast, the older Cretaceous sequences through their lesser economic importance are relatively less explored. The sedimentational history of the Gippsland Basin has largely followed along similar lines of development to the many other southern Australian basins since the Cretaceous break-up of Gondwanaland. However, the scale of accumulation of coal and hydrocarbon source rocks is unprecedented and differentiates this basin, for reasons less well understood, from the others. Large scale open cut brown coal mining since the late-1920s has been carried out in the western extremities of the basin, while vigorous extraction of some two thirds of Australian petroleum products taken place in the offshore part. Brown coal seam thicknesses and economically winnable reserves are huge and outrank most other brown coal basins of the world. Development of the resource currently meets the need for electricity generation throughout the State of Victoria, but other future developments such as conversion to oil, being investigated.

Jan 1, 1992

By B Leisemann, M Watkinson

Coal augering is an ideal method for recovering coal from the highwalls of open cut coalmines. Coal augering is a simple process whereby additional flights are added to the auger cutting head and auger holes are drilled at 1.9 m diameter up to 200 metres deep. Traditional monitoring was located at the mouth of the hole and if methane was encountered above two per cent, inert gas was delivered into the mouth of the hole to deplete the oxygen content at the auger cutting head below 12 per cent. The auger operator was asked the question ‘how do you know that this is the case?’ Trials were undertaken to prove that the oxygen content at the cutting head did drop below 12 per cent (the lowest limit for methane to ignite, also known as the oxygen nose point). Initial trials showed that the oxygen content in the mouth of the hole did not drop below 12 per cent and modifications were made to hold the inert gases in the mouth of the hole so that the auger flights could take this inert gas into the hole. In-hole monitoring, after completion of mining and after extracting the auger flights, showed that the atmosphere quickly returned to fresh air. In-hole monitoring was also tried during the augering process and yielded valuable results. This paper will discuss the results of the monitoring, information on the gas results obtained and the methodologies used to optimise the oxygen content at the auger face.CITATION:Watkinson, M and Leisemann, B, 2017. Inertisation of coal augering holes, in Proceedings Australian Mine Vent Conference 2017, pp 293–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By W Donovan

Concern exists about the potential release of metals from the proposed mining operation at Martha Hill to the Ohinemuri River. Speculation on possible impacts is fuelled by the dearth of published data on existing metal levels not only for this river system but for streams throughout the Coromandel. At first sight this lack of data is surprising given the apparent interest in this subject and the fact that future mining activity in this region has been a possibility since at least 1979. That such a situation has arisen is not altogether unexpected given the difficulties faced by various organisations, including the mining industry, in determining metal levels which are generally acknowledged to be low. This paper presents data for a number of stations in the vicinity of the proposed operation; it explains the analytical procedures which were adopted and the rationale for them and relates the information which has been obtained to water quality criteria.

Jan 1, 1986

The recovery by flotation of some complex uranium minerals such as brannerite and davidite is described. Anionic reagents used for flotation of iron and titanium oxides' are suitable. If care is taken, to emulsify the reagents the slime fractions may be satisfactorilytreated.INTRODUCTIONUranium ores are usually treated by direct leaching with acid or alkali according to the nature of the gangue materials. Concentration of the uranium minerals prior to leaching is not commonly practised because of the earthy nature of most uranium minerals and the difficult mineral dressing problem they pose. Some of the harder complex oxides such as davidite and brannerite are amenable to flotation. This is fortunate since they usually require an expensive, strong acid treat~ent to dissolve the uranium. Flotation tests were commenced in 1949 by officers of the South Australian Department of Mines stationed at Adelaide, first in the School of Mines, then in the University of Adelaide and finally in Departmental mineral dressing laboratories at Thebarton. Separation of daviditefrom Radium Hill and Mount Victoria ores, brannerite from Crocker's Well ore, and secondary uranium minerals from Myponga ore was attempted.The development of the flotation reagents to separate the oxides from silica and the silicates is first described, then some of the results obtained are presented as tables.DEVELOPMENT OF FLOTATION REAGENTSThe davidite at Radium Hill is associated with iron and titanium oxides, qu;a,rtz and biotite as replacement deposits in shears. The davidite, rutile,' ilmenite and hematite usually occur in segregations from nut size to masses of several pounds. They are associated as a complexity of...

Jan 1, 1955

The Burra Burra Mine is situated in complexly folded Torrensian dolomites and limestones forming the faulted axial region of a major anticline. The orebody mined was largely of secondary origin and confined between two faults, Kingston's on the west and Tinline's on the east. The orebody occurred at the junction between cherty dolomites and a clastic limestone with a large mass of marble breccia along its western margin. Secondary ore consisted of carbonates and oxides in the breccia and the ore bed and detrital copper minerals deposited as part of a clastic breccia in sinkholes and solution cavities in the dolomites and ore beds.Primary sulphides occur disseminated in the marble breccia and in stratiform habit in the ore bed. Kingston's so-called "lode" may be mineralized marble breccia.The marble breccia appears to be of diapiric or sedimentary origin and there is evidence to support a sedimentary origin for some of the copper sulphides. No igneous rocks have been discovered within 20 miles of the mine and any hydrothermal activities were probably at comparatively low temperature. The possibility of extensive stratiform and disseminated copper sulphide mineralization in the marble breccia and ore bed requires testing by further drilling and geophysical surveys.INTRODUCTIONThe re-interpretation of Burra Burra geology and ore formation discussed in this paper resulted from a comprehensive investigation of the mine and its surrounding district begun in December 1961 and in progress at the time of writing. (February 1963). The decision to investigate Burra Burra was taken after a thorough examination of records and reports of all non-ferrous metal deposits throughout South Australia and was given impetus by a report by Thomson (1963) suggesting a sedimentary origin for the copper mineralization. Although the author does not concur fully with Thomson's interpretation there is no doubt that sedimentary processes have played an important part in the formation of the Burra Burra copper deposit, nor is there any doubt that igneous activity played no part.

Jan 1, 1963

Currently raw brown coal is fired in the Latrotx; 'ahcc th,iki~, Lanying with it two major penalties, (a) boiler efficiency of 65 - 70 per cent (in terms of GCV), (b) much higher boiler cost than for black coal. Drying the coal, in energy-efficient, and cost-efficient manner, opens the way to efficiencies of order 88 per cent and enables the lower cost black coal type boilers to be used. With the higher boiler efficiency goes much higher combustion temperatures and the effect of this on radiative heat transfer is a major factor in reducing boiler cost. In a fluidised-bed combustor the temperature is controlled to 800C - 900C. In a pulverised fuel combustor higher temperatures are however achieved and can increase boiler fouling due to the salt content of the coal. This is a problem which needs to be solved. Victoria has the prospect of lifting efficiency from 28/29 per cent to 35 per cent, of reducing carbon dioxide output correspondingly and reducing cost of power stations. So far as gasification is concerned, efficient removal of liquid water from the coal is important to the overall efficiency.

Jan 1, 1992

By Matthew I. G

A new process for leaching zinc sulphide concentrates with gaseous mixtures of SO2 and O2 in aqueous solution is described.The reaction of SO2/O2 with Rosebery, Mt. Isa, Broken Hill and Elura zinc concentrates yields zinc and iron sulphates, elemental sulphur and some sulphuric acid. Rates of zinc extraction are controlled by a surface chemical reaction without apparent interference from the elemental sulphur layer for SO2 concentrations up to 9 per cent in the gas phase. Pyrite in concentrate exerts an activating effect, possibly through galvanic interaction with the sphalerite. Metal extractions are dependent on SO2 and O2 tenors of the gas, particle size, and the acidity and zinc content of the solution, but are independent of the ferric ion level. Extractions also reach maxima at about 85°C.Generation of acid may be prevented by conducting the reaction in the presence of ferrous iron and at acidities of 40 g/l or greater. Zinc and iron levels in Elura lead concentrate may be reduced by leaching with SO2/O2.

Jan 1, 1981

Significance of the body of iron oxide, which in part overlies as its hanging-wall the rich chalcocite ore-body at Mount Oxide, Queensland, has been variously interpreted by engineers and geologists who have inspected the deposit.Among the interpretations offered is the one that the body represents the residual of an original medium to low grade...

Jan 1, 1939

Hot briquetting is a reliable, fully developed industrial concept for the passivation of direct reduced iron produced with the various processes of direct reduction. During hot briquetting, the large specific surface area of direct reduced iron is drastically reduced, and therefore the well-known problems caused by reoxidation and overheating are avoided. Even the shipping instructions published by the International Maritime Organisation (IMO) confirm that Hot Briquetted Iron (HBI) can be handled and shipped without special precautions. From the mid-1970s until today, after extensive pilot testing of the technology, a number of industrial plants for the hot briquetting of direct reduced iron have gone into operation. Additional hot briquetting plants for already established but also for new direct reduction processes are tinder construction or in different stages of planning. This paper describes the characteristics of HBI and its current industrial application for various Direct Reduction Processes.

Jan 1, 1999

Fines and unnecessarily small rock fragments are created by as many as four identifiable breakage mechanisms which operate close to the charged section or sections of the blasthole. The peak blasthole pressure (Pb) should not exceed that value at which the rock starts to fail in compression. Excessive Pb values can be prevented by carefully selecting:1. the composition, density and/or diameter of the charge, and2. the initiation/priming system.The percentage of fines increases with:1. increases in the charge diameter:blasthole diameter ratio, burden distance, blasthole diameter, effective sub-drilling and size of blast, and2. decreases in blasthole spacing, stemming height and the length:width ratio of the blast block.Decked charges tend to reduce the percentage of fines.Excessive fragmentation is more evident in buffer blasting and sinking cut shots than in blasts fired to a clean free face. Initiation sequences which give effective burdens considerably less than drilled burdens encourage the minimization of fines, as does an inter-row delay time which promotes good progressive relief of burden.The wastage of explosive energy in creating fines is most pronounced where fully-coupled, energetic charges are fired in weak and/or highly porous rocks. This is especially so where forward movement of the strata is impeded by buffer rock, excessive burden distances and/or inadequate inter-row delay times.

Jan 1, 1979

In referring to two subjects of interest to the Members of this Australasian Institute of Mining Engineers, I would at the outset desire to express our gratification that to-day we are able to welcome as now united with ourselves, those members who until recently constituted the New Zealand Institute. It is hoped that the amalgamation so amicably arranged may be productive of the best results to all concerned, incorporated as this combination has been at the moment of the fulfilment of that greater political union, the Australian Commonwealth.Since last Annual Meeting held in Brisbane, we have come under the same roof as the Chamber of Mines of Victoria, and we entertain the hope that as that Chamber and this Institute possess so many interests in common in the encouragement and advancement of mining and metallurgical progress in these colonies, that much mutual benefit will ensue. There are many directions in which each body can assist the other, and I trust that a friendly co-operation will be maintained.It is gratifying to feel that in all the colonies a distinct movement is being made to increase the facilities for education in Mining and Metallurgy but if I may refer to our colony of Victoria in particular, we have to express the profound regret that in the means of education in the higher branches, we occupy an inferior position, and it is quite certain that we will continue to do so unless the Government is prepared to subordinate provincial considerations to the weightier.

Jan 1, 1901

When the HSE Act was introduced in New Zealand in April 1993, one of the prime aims of the Government was to signal to the industry. The Government's recognition of the employer as the key person responsible for safety and health in the workplace and to actively encourage employers to self manage the health and safety function. Because of the significant change in the philosophy behind the new legislation, and because of the inherently conservative nature of the mining industry, it has taken some years for both the industry and the regulators to reach the stage of considering the framework in which a controlled degree of self management can proceed.   In this paper, some of the issues relating to the legitimacy of the process are considered, some of the questions raised in the minds of those charged with implementing the legislation are discussed, and the views of some eminent authors are examined.   The latter part of the paper focuses on a programme called the Reduced Site Surveillance Programme, which grew out of Goal 2 of the New Zealand Mining Inspection Group's 5-Year Strategic Plan. The programme is described in some detail, and the criteria applied at each stage of the programme is discussed. The paper concludes with the author's expectations of the longer term outcomes of the programme.

Jan 1, 1997

The area around Big Bell was actively explored and sporadically mined for gold from 1904 onwards. The lease was named Big Bell in 1913. The property became established as a major mining centre with the development of the Big Bell underground mine in 1936. Mining operations commenced in late 1937 and ceased in January 1955, after milling 5.56 million tonnes of ore and producing nearly 21 tonnes of gold. In 1969 Australian Consolidated Minerals Ltd (A.C.M.) acquired the deposit then explored it alone and in joint venture until the current joint venture agreement with a subsidiary of Placer Pacific Limited (PPL) was negotiated in 1984. Following exploration and evaluation of near surface mineralisation, and a reassessment of the remnant pillars underground, the concept of a large open pit in conjunction with an underground mine evolved. The feasibility study was completed in October 1987, and the decision to go ahead was formally announced on 2nd December 1987. Placer Dome Technical Services Ltd were contracted to be the Project Managers, commencing construction on site early in January 1988 and handing the plant over to the operators 13 months later. The capital cost of the project at handover was estimated to be $133 million. The operating team commenced pre-production stripping of the open pit on 1st May 1988. By 31st January 1989 almost 16.0 million tonnes had been stripped and 350,000 tonnes of ore stockpiled.

Jan 1, 1989

Gold, silver and palladium may be separated from the other base metals and sulphur contained in copper sulphide precipitates derived from the Sherritt-Gordon nickel process using a process involving an oxidation roast, a reduction roast and a Cu(II)/acetonitrile leach. Sulphur is removed as SO, in an oxidation roast and the hot calcine is reduced with carbon, or with carbon plus cuprous chloride. The resulting product contains metallic copper which is readily dissolved with cupric ions in aqueous acetonitrile solution. Copper powder is recovered by thermal disproportionation. The residue contains the bulk of the iron and precious metals and may be treated by a number of methods, including direct cyanidation or melting with suitable fluxes. Melting the residue will produce a copper alloy containing the precious metals and remove the iron as a slag. The alloy can be recycled to the copper leaching stage or sent for toll refining depending on the precious metal content. Impurities from the leaching circuit are controlled by a bleed circuit which in one approach utilizes the SO, from the calciner to produce Chevreul's salt and separates copper from the soluble cobalt and nickel. Alternatively, the bleed may be directed back to the main refinery copper boil stage or oxydrolysis stage.

Jan 1, 1982

A study of literature on the epidiorite dykes which transgress the Broken Hill lode and its wall rocks reveals a considerable diversity of thought regarding the time of emplacement of such dykes. In this paper it is deduced that the epidiorite dykes were formed at a late stage and were probably post-ore. Detailed mapping, sampling, and correlation of data from over 100 exposures substantiates this deduction. Physical disruption of the epidiorite dykes is indicated and some interaction of the epidiorite and ore at the time of intrusion is inferred.Further petrological study may confirm this.

Jan 1, 1968