Search Documents

By N Power, R Hassell, E Jones

Wiluna Mining Corporation are progressively re-entering the old Wiluna underground mining complex. The existing underground was abandoned in 2013 by previous owners and left to flood with water levels reaching above the East Pit portal and Happy Jack Pit portal and up to 300 m below surface in the Bulletin underground. Re-entering the mine commenced in 2017 with dewatering of the Bulletin decline. The underground development had been previously supported with friction bolts, with weld mesh in places. Until mid-2021 rehabilitation requirements were based on an external visual inspection of the installed ground support scheme. However, several incidents involving falls of ground due to corroded bolts have occurred during this time, showing that this approach was inadequate. The challenge the operation faced was should the entire decline be rehabilitated, the implication being not only a large rehabilitation cost but also the impact of severe delays to the mining schedule. The question was asked can the operation better understand the level of corrosion damage and potentially optimise rehabilitation requirements. A proposal to use a systematic approach to assess corrosion by environmental condition mapping, visual external corrosion assessment, and internal corrosion assessment via borehole camera inspections was provided and accepted by Wiluna Mining Corporation. The objective of this work was to produce a three-dimensional map showing the degree of corrosion on the reinforcement systems in the capital infrastructure, this would then be used to risk assess and prioritise rehabilitation requirements. This paper summarises the approach, methodology and results that provided the Wiluna mine planning team with information to enable planning of resources and budget to justify priorities of rehabilitation.

Nov 29, 2022

By A L. Stewart, M Baatar

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.The Middle Palaeozoic Gurvansaikhan Belt (Southern Mongolia) of the Central Asian Orogenic Belt is one of Central Asia’s most significant emerging porphyry copper provinces. The belt has become the focus of extensive exploration for porphyry copper-gold deposits over the last decade following the discovery of the giant Oyu Tolgoi porphyry copper-gold deposit. The Gurvansaikhan Belt is known to host porphyry deposits of Late Devonian (~370 Ma) and Early Carboniferous (~320 Ma) age. The characteristics of Early Carboniferous porphyry systems are poorly known compared to their older counterparts, despite their probable abundance and potential economic significance. Exploration within the Kharmagtai porphyry breccia complex has identified multiple cogenetic gold-copper-porphyry centres and late-stage mineralised magmatic-hydrothermal tourmaline breccias emplacement within a composite high-K calc-alkaline quartz monzodiorite intrusive complex. Early porphyry alteration and mineralisation at Kharmagtai are zoned around vertically attenuated early- and inter-mineral quartz monzodiorite dykes and stocks and comprises a complex sequence of calc-potassic, potassic and propylitic assemblages. Hematite dusting is a common alteration product that gives intrusions and the host rocks a distinctive pink-orange colour. Several of the systems have bornite-rich cores, where mineralisation is characterised by high gold grades (0.7 to >5 g/t Au) that zone outward to chalcopyrite-rich and then outer pyritic halos. Early stockwork mineralisation is overprinted by magmatic-hydrothermal tourmaline breccias. High-grade magmatic-hydrothermal tourmaline breccias form part of a major copper-gold mineralised breccia system with significant exploration potential. The Early Carboniferous porphyry copper-gold systems of the Gurvansaikhan Belt represent a substantial exploration challenge in an area of increasing exploration maturity. This paper summarises the characteristics of the Kharmagtai porphyry system that have helped to define the Early Carboniferous porphyry province of the Gurvansaikhan Belt and discusses implications for future exploration.CITATION:Stewart, A L and Baatar, M, 2015. The Kharmagtai porphyry breccia complex – characteristics of early Carboniferous porphyry mineralisation in the Gurvansaikhan Belt, Southern Mongolia, in Proceedings PACRIM 2015 Congress, pp 383–388 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Y Zhou, Y Liu, J-P Yang, P Wang, K Hu

"Large-scale mine reclamation has taken place recently in response to the implementation of mining regulations in China. Effective monitoring of the progress of reclaimed land is a critical procedure to assess the quality of reclamation program and to ensure that mining enterprises fulfill their reclamation responsibilities. The present paper reports a preliminary study that examines the situation of mine land reclamation monitoring. Based on the monitoring, some general requirements for mined land reclamation have been proposed, including: the monitoring should be systematic and comprehensive the monitoring should be adapted to specific local conditions the monitoring should be reasonably optimised via scientific methods and technology the monitoring should stick to a variety of national technical criteria.The aim of land reclamation monitoring is to evaluate changes of critical indicators closely reflecting the development trend of the reclaimed mined land, to develop or improve the criteria and technical parameters specific to the site, and to prevent secondary environmental degradation. Based on these requirements and aim, the monitoring should cover the progress of reclamation, establishment of vegetation and plant community development; and recovery of land and water quality in the reclamation area. Regulatory measures are proposed which would improve the work of mine reclamation monitoring in terms of regulation, organisation and financial support.CITATION :Wang, P, Yang, J-P, Zhou, Y, Hu, K and Liu, Y, 2012. The primary framework for the mechanism of the mine reclamation monitoring in China, in Proceedings Life-of-Mine 2012, pp 47-50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By Y S. Zhang

Natural phenomena and human engineering construction activities had great influence on the geosciences space. Natural disasters, particularly mine disaster and other geological disasters happened frequently, which brought great losses both in people’s lives and economics, therefore, to explore the essential causes and mechanisms of disaster by some useful approaches is the most important step in mine disaster prevention. In a variety of methods, building an aground-underground seamlessly integrated model, and then analysing the formation and development mechanism of mining disaster based on this model is a useful way. In this paper, we studied an aground-underground seamlessly Integrated modelling method, and correspondingly given an aground-underground seamlessly integrated 3D spatial model, CSG+CD-TIN+GTP-TTS, by which we can carry out analysis of surface subsidence and underground laneway distortion efficiently, finally preliminary applications verified the effectiveness of this method.

Nov 22, 2011

By T Walton, C Perring, M Pepper, G Gerber

The Yandicoogina Channel Iron Deposit (CID) is an accumulation of iron pisolites cemented by a goethite-rich matrix. The Yandicoogina CID’s are found in a palaeochannel that meanders within a broad structural basin of the Yandicoogina Syncline in Pilbara region of Western Australia. RTIO Yandicoogina Mine Geology team contributed to a number of strategies maximising the iron ore reserves mined by Rio Tinto. Two strategies are discussed: the replacement of the Batter-Berm final pit walls by contour dozing; and upgrading the lower grade material to crusher feed. 1. Contour dozing – traditional Batter-Berm pit final wall configuration left kilometre long wedges of ore sterilised around bench margins. Contour dozing final walls (ie dozing of ore down the ore-waste contact) as internally defined by RTIO Yandicoogina Mine Geology (Mine Geology), enabled recovery of additional crusher feed. 2. Upgrade of lower grade material – the lower ore domain (GVL) within the Yandicoogina orebody contains numerous clay pods. Contaminant Al2O3 inherent within clay pods can result in CID material outside of crusher feed grade specifications, causing it to be flagged as ‘internal waste’ in mining models and permanently lost to waste dumps. In 2011, after multiple tests, Mine Geology demonstrated that this material could be upgraded to crusher feed via wet processing. With the support of the RTIO Metallurgical Development team new grade specifications were defined. The resulting material has been used to supplement higher grade ore. While increasing the mining ore output, these ongoing value-adding strategies also promote more sustainable mining via better use of the non-renewable iron ore commodity. The initiatives extend mine life, reduce waste movement, improve strip ratio and increase productivity

Mar 22, 2022

By M Akop, G Phillips, L Elliott

An estimation geologist has many tools in their kit and using the correct one for the job is vital for creating a useful model. Reconciliation is a key step to monitor the performance of a resource model and to ensure the correct tools have been selected and appropriate parameters are set. This paper presents an example of refining the estimation methodology for a Channel Iron Deposit (CID), resulting in an improved model. Rio Tinto Iron Ore (RTIO) CIDs are unique iron ore deposits located in the Pilbara region of Western Australia and contribute a significant volume to the world’s seaborne iron ore market. A problematic feature of these deposits is the irregular dispersion of clay pods that cannot be delineated with confidence within the resolution of the exploration drilling. Resource to grade control reconciliation showed an over-prediction of high-grade material in the resource model. A fresh approach was required to improve grade and tonnage predictions. Historically, clay pods were delineated using traditional wireframing techniques and estimated using ordinary kriging with hard boundaries. The new method utilised indicator kriging to estimate the probability of clay. Probabilities generated from the indicator kriging estimate were used as an additional weighting following the ordinary kriging of grades. Results showed indicator kriging improved global high-grade tonnes reconciliation, however, as expected, it did not improve the spatial prediction of clay. Based on improved reconciliation results indicator kriging has now been adopted as a suitable alternative for analogous CIDs at RTIO. These improvements benefit the mine planning process, but do not replace grade control models.

Mar 22, 2022

By S Talu, E Savage, P Sturm, A van As

It is estimated that substandard ground support installations and elements cost the Rio Tinto Copper Group millions of dollars between 2000 and 2014. These issues have also created significant safety and financial risks in Rio Tinto mines. As a result, Rio Tinto Copper has developed CaveCAD, an integrated system to collect, store and analyse all ground support-related data. The CaveCAD system stores geotechnical data and has the ability to automatically import data, collect data through tablet applications, report processed/analysed data and present this data through 3D visualisation software.The CaveCAD Ground Support module closes the design–implementation–verification loop by providing a method of verifying the compliance of all installed ground support, recording manufacturer specifications, recording quality control test compliance and rectifying any non-conformant areas. The module uses innovative technology to create value through cost saving, safety improvements and data collection efficiency. Cost savings will be achieved by a decreased need for excavation rehabilitation, less ‘waste’ due to faulty installation and quality assurance checks reducing the likelihood of substandard support units being used. Data collection will be improved through the use of a mobile tablet application that can be used underground in ‘off-line’ environments.CITATION:Savage, E, Talu, S, Sturm, P and Van As, A, 2016. Development and implementation of the CaveCAD ground support module for cost and safety improvements in block cave mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 769–772 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By G D. Matthews, M E. Haylett, S Khosrowshahi, A Weeks

Effective domaining is fundamental to geostatistical modelling for grade control. Through analysis of lithological, structural and alteration logging data, effective groupings (domains) can be identified and employed for estimation or simulation purposes.The poor definition of domains can adversely affect the grade control model resulting in a misinterpretation of the optimal ore-waste boundary and ultimately reduces the quality of recovered ore. The implementation of an appropriate domaining strategy is therefore expected to improve recovery and reconciliation.A thorough understanding of the geology of the deposit and adequate sample data is required for selecting domains. For new deposits, a resource drill database and resource model may be the only information available. Where extension to a previous operation is taking place, historic grade control, mapping and exposed geology may be used to improve domain selection. Preconceptions about domains, should they exist, need to be re-evaluated and tested to ensure they are fit for the purposes of grade control.While mining progresses, the domain model is re-evaluated to ensure that the previous interpretation is still suitable for the present configuration and geology. The grade control process, being iterative, lends itself to regular review and continuous improvement as further data is collected during the grade control cycle. Regular updates to the geology model, mapping, geostatistical data analysis and review of variography will provide indications of a changing domaining environment.Narrow vein gold deposits, which may have several factors influencing mineralisation, present considerable domaining challenges. By scrutinising the data, sample populations can be grouped into domains, which not only improve ore recovery, but help assist in the development of a mine geology model.CITATION:Matthews, G D, Haylett, M E, Weeks, A and Khosrowshahi, S, 2014. Effective domain selection for grade control in narrow vein gold deposits, in Proceedings Ninth International Mining Geology Conference 2014 , pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By F Musa

One of the main energy efficiency opportunities identified from the majority of mine site energy audits is to optimize the comminution circuit to reduce energy consumption through improved throughput and product size distribution. Typical analysis reviews comminution process efficiency/inefficiency i.e. utilization of grinding mills, process bottlenecks and product vs. target size, to identify instances of overgrinding or undergrinding. From this, it is possible to establish the potential improvement that could be gained through formal plant optimization and what the optimization program would entail. It can also sometimes reveal immediate opportunities for process improvement. This paper presents steps that can be taken to optimize the efficiency of comminution circuits.

Aug 8, 2011

By J Lyons, S Baker, D MacHunter, D Pepper

Mineral processing plants require a storage buffer to bridge differences in production rates between mining and processing. Where coarse ores are processed, such as coal or hard rock, this buffer may be an ore stockpile or silo. For wet-mining processes, eg dredging or hydraulic mining, or where fine ores are slurried close to the mining face, a surge-bin is used to contain the plant feed and smooth out the variations in mining rates. These bins have gradually evolved from simple storage vessels to units that are now frequently part of the mineral separation process itself, such as providing a desliming function to remove deleterious ultrafine gangue. This feed conditioning is often essential to achieve the levels of plant performance required in times of declining ore grades and or where inherent ore characteristics make separations harder to achieve. To achieve these dual roles requires careful consideration of bin design factors such as geometry and lining selection and increased use of instrumentation and advanced, or remotely supervised, control systems. All this ensures they provide capacity to smooth out variations in mining rates and guarantees that when conditioning ores or adjusting slurry densities ahead of the plant it is achieved without loss of valuable minerals. This paper examines the evolution of the modern surge-bin from a simple, so called, constant density tank with its inherent mass-flow compromises, limited feed preparation and beneficiation abilities, and footprint penalty, to a current state-of-the-art surge-bin, the LFCU, with a control system which provides demonstrable steady outputs, while conditioning and in some cases beneficiating the ROM material and all from a highly compact unit. It further discusses their use in other applications around the world, for example providing the necessary security for long distant high-density pumping systems; constant high density, low water usage, tailings disposal pipelines and high capacity ultrafine iron ore beneficiation.

Aug 24, 2022

By J Player, G Sweby

The material properties and hence performance of saturated alluvial sediments slope can be incorrectly forecast if the water content is not preserved, and materials properties not correctly determined. The occurrence of saturated sediments in the Western Australia (WA) Goldfields, while not common, should be a significant investigation focus. Geotechnical engineers new to the area may be unaware of this and hence the importance of correct testing and determination of the material strength. Application of appropriate analysis to determine stable pit slopes to an acceptable level of risk, is not possible unless the appropriate strength and hydrogeological parameters have been established at the outset. A back analysis is presented of a pit that had extensive slope failures in alluvial clay-rich sediments with discussion on the approach adopted by the original design engineers to assess pit wall stability and consequent poor slope performance. Learnings from a full pit 3D back analysis are presented, with an approach to geotechnical and hydrogeological investigations and analysis for slopes in similar materials.

Jun 22, 2022

By A P. Wilkinson

This paper reports on the implementation of the critical control concept to manage material risks in the mining and metals industries. The critical control management (CCM) approach assumes it is better to identify weaknesses in risk controls before an incident happens as opposed to discovering weaknesses from an investigation after an incident occurs. The first is sometimes referred to as active monitoring and the second as reactive monitoring (Health and Safety Executive and Chemical Industries Association, 2006). Both are needed. However, whilst methods for both active and reactive monitoring of risk controls are well established in many high hazard industries, such as oil and gas, petroleum and chemical industries, until the publication in 2015 of the International Council on Mining and Metals (ICMM) guides, (Good Practice Guide and the subsequent Implementation Guide) (ICMM, 2015), there was no specific mining and metals industry guidance on critical control management. This paper reports on progress in implementing the ICMM guidance drawing on two main sources. First, a benchmarking survey of a representative sample of coal and metalliferous mines, both underground and open cut/pit), sponsored jointly by the Queensland Resources Council and the Queensland Commissioner for Resources Safety and Health in the context of a recommendation that the Queensland mining industry adopts high reliability organisation (HRO) principals (Queensland Resources Council and Commissioner for Resources Safety and Health, 2022). Second, it draws on Noetic’s experience of implementing critical control management in mining and other high hazard industries in Australia, Africa, China and North America (Wilkinson, 2018). The paper describes good practices found and where significant improvements can be made, providing specific and actionable examples of both. From this it also identifies how future guidance on this topic could be improved.

Apr 16, 2024

By P Brown, M Nagarajan, A Green, P Dare-Bryan

Coal loss is an important issue at many coalmines, with losses of five per cent being common. The type of loss varies from mine to mine but is dependent on mine strata, the drilling and blasting processes applied and the mining method used. Typical coal loss mechanisms from the drill and blast process are coal roof damage and edge loss. Usually a reduction in coal loss is in direct competition with the need to provide material that is well-fragmented and a muck pile that has the required cast percentage. These competing issues were addressed over a two-year period at a mine in the New South Wales Coalfields by implementing a five-step approach. This was centred around building an understanding of the coal loss mechanisms utilising proprietary heave- modelling software, measuring coal losses by comparing survey to drill and/or gamma logs and implementing appropriate coal loss reduction processes. The end result exceeded expectations with a 95 per cent reduction in coal loss. Mine excavation productivity was maintained and coal loss minimised to less than one per cent of the in situ coal block.CITATION:Nagarajan, M, Green, A, Brown, P and Dare-Bryan, P, 2015. Managing coal loss using blast models and field measurement, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 429–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By F Flitti, M Haest, O Dominguez, D Mittrup, G Hird

The automated geology interpretation (AGI) tool has been developed in BHP Billiton to automate stratigraphy logging of drill holes, using any available quantitative data sets. At present, AGI is set-up to utilise geochemistry and mineralogy from infrared spectroscopic data to predict stratigraphy. Once the AGI tool is calibrated, results show that the tool is capable of automatically defining stratigraphy across all of the deposit types, encountered by BHP Billiton Iron Ore in the north-west of Western Australia. Accuracy of AGI at predicting stratigraphy is on average better than 75 per cent, with average accuracies exceeding 85 per cent for some deposit types. The AGI tool can deliver fast, accurate, consistent and objective geological interpretations.AGI is currently being implemented in BHP Billiton Iron Ore Exploration to streamline the drill hole logging process and allow geologists to spend less time defining stratigraphy at the drill hole level and more time investigating stratigraphy in 3D. This will deliver improved geology models, with significant downstream benefits in terms of better resource models, more accurate mine plans, higher plant efficiencies and more consistent ore products, driving productivity in BHP Billiton Iron Ore over the next decade.CITATION:Mittrup, D, Flitti, F, Hird, G, Haest, M and Dominguez, O, 2015. Semi-automated geological interpretation using assay and infrared spectroscopic sensing parameters towards improvements in geological modelling, in Proceedings Iron Ore 2015, pp 313–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R Stefansen, T Wisdom, A Nicholson, K Rahal

The challenges of increasingly scarce water resources and the risk of dam failures has seen the mining industry turn to sustainable tailings management solutions such as dewatering and dry stacking. Filtering tailings has been seen in the past as a cost-prohibitive process for larger throughput mines. However, as larger pressure filters are developed, the economic case for filtered tailings has gained traction.Focus has largely been placed on the correct design and operation of the filters. It is critical, however, that the material handling portion of the disposal system is also properly designed and operated. Thorough testing at laboratory and pilot scale to determine the conveying properties of the filtered material needs to be conducted. This testing will insure the material handling system meets the important availability needs of the mine even during periods of variability in the upstream processes and mine plan.The control system must also be robust and flexible in design to compensate for this upstream process variability. The control system needs to allow for different flowsheets including straight filtered tails as well as EcoTails™, a low-energy solution for co-mingling waste rock and filter cake.This paper will present case studies of different material handling solutions, the testing required for them and the lessons learned from each.CITATION:Rahal, K, Nicholson, A, Stefansen, R and Wisdom, T, 2018. Material handling testing and control system requirements for dry stack tailings, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By M Doran

The Olympic Dam mine utilises 1.1 m to 1.4 m diameter raise bores for generating the initial slot void for most production stopes. Slot raise bores generally span two development levels ranging from 30 m to 50 m in height. Raise bores are reamed upward and typically leave a cap of rock equivalent to two times the raise bore diameter on the drill level (minimum 3 m). This provides safe access over the cap for subsequent production activities. It is therefore critical to ensure robust falling object protection for personnel accessing underneath, and in the vicinity of the raise bore void on the lower level. Recently, a number of mesh failures have occurred at Olympic Dam as a result of falling rock from the underside of the cap and raise walls. In addition, as Olympic Dam transitions to deeper and more challenging ground conditions, rockfall-off onto the raise bore protection mesh is anticipated to increase in frequency. This paper discusses the evolution of raise bore protection mesh used at Olympic Dam and presents results from recent site-based drop testing. This impact testing was carried out using a built for purpose object to replicate point loading and shear failure of mesh wires. Testing was also carried out on an improved mesh design which utilises two layers of Geobrugg high-tensile MINAX mesh. Results from the drop testing suggest an improvement in performance of the raise bore protection mesh is realised with the updated design.

Mar 29, 2023

By H Arvidson, B Spence, S Helm

Mining is the art of disturbing ground. All phases of a mine’s life cycle from exploration to building and operating a mine, through closure, has a physical impact on the earth. There is currently increasing public and stakeholder awareness owing to a wide range of issues including heritage protection, environmental stewardship, and social impacts therefore ground disturbance must be conducted in a way that honours and respects all agreements, regulations, legislation, and social expectations. A comprehensive ground disturbance permitting process has been developed through consultation with major mining companies and Traditional Owner groups. It operates from strategic business planning through to closure and rehabilitation. Adherence to the principles and process of permitting helps to minimise risk by ensuring that mining companies conduct their business in an inclusive, professional, reliable, and consistent manner that stakeholders reasonably expect, and that mining companies can be proud of. Built on a geographical information system, supplemented with a specialist database, this process allows request, review, and approval by subject matter experts, to operate in a common environment that is transparent, facilitates collaboration, improves efficiencies, and reduces the risk of error or omission. The application of new technology can effectively highlight changes that naturally occur in today’s dynamic ESG domain and provides the perfect platform to record actual disturbance against authorised and planned allowances. The social license to operate demands that strong governance of the ground disturbance process, described herein, can be demonstrated to any interested stakeholder, and mining companies recognise that this principle is central to the betterment of the mining industry.

Sep 18, 2023

By J Seery, N Savage, A Wilson, L Nicholas

Geological modelling provides a means of spatially representing the three dimensional distribution of geological information to downstream stakeholders. The geologist completing the modelling work intimately understands the varying degrees of confidence, assumptions and extrapolation required to honour the data. Geological models are often taken and used by stakeholders without fully understanding this modelling process. This can lead to confusion amongst stakeholders when the geological model shows variable reconciliation. A method for visually communicating the confidence of the spatial distribution of geological models has been created by the Rio Tinto Iron Ore structural geology group for use primarily in geotechnical engineering investigations. A numeric confidence rating is assigned to each geological data point used in the creation of a geological surface. This is based on data type, collection method and reliability to indicate potential error in distance from its modelled location. In regions of sparse data, confidence ratings are inserted based upon the geologistÆs experience and knowledge of the geology, whereas mapped geological contacts or drill hole intersections are assigned a higher confidence rating. A regular grid of points is registered to the geological surface and each of these grid points is assigned a confidence rating using an inverse distance weighting using a nearest neighbour approach. The resulting grid is colour coded according to the confidence rating to provide a visual representation of the variable confidence of the geological surface in three dimensions. Subjectivity and bias from the geologist is minimised by critically analysing the input geological data and then applying this methodology to represent the confidence in the spatial characteristics of geological models. Understanding of this confidence enables mining professionals to make informed decisions and identify areas that require further geological investigative work. CITATION:Savage, N, Nicholas, L, Wilson, A and Seery, J, 2013. Visual communication of geological confidence - a move toward a less subjective approach, in Proceedings Iron Ore 2013 , pp 169-174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By C McHugh, F Oppolzer, B Rogers, A Stokes

Rio Tinto has embarked on a journey to use automation to improve the performance of its surface mines. The driver for automation has more to do with improving the accuracy and consistency of mining processes and less to do with cost savings through labour reduction.A key task in most surface mines is blasthole drilling. The degree to how well this is done cascades through the downstream mining process. It impacts scheduling, excavation, slope stability, material handling, beneficiation, ore loss and final product blending. Improved blasthole drilling was identified as an objective that has a significant business case in most of Rio TintoÆs surface mines.This paper describes Rio TintoÆs multi-drill automation project, which has developed a robust system for automating most of the functions on several Caterpillar SKSS16 drill rigs. Automated drilling is currently being trialled in production at the West Angelas iron ore mine in the Pilbara region of Western Australia. A description of the essential elements of the automated multi-drill system is given together with an overview of how automated drilling is performed remotely from the operating bench.A review of the performance and benefits of the automated multi-drill system is given together with future plans to extend the functionality of automated drills.CITATION:McHugh, C, Stokes, A, Oppolzer, F and Rogers, B, 2012. Automated multi-drills in Rio Tinto, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 83-88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By J Fewings, T McCredden, S Seet, C Fitzmaurice

"Flotation of nickel sulfide ores are generally constrained by nickel grade and impurity concentrations (notably magnesium and arsenic) in the product delivered to smelters. Being a physical separation process, flotation recoveries and grades are limited by the grade recovery curve of a particular operation, where increasing product grades are invariably associated with lower recoveries. Impurities put further pressure on this relationship, as removal of impurities from the final concentrate is almost always associated with nickel losses.Western Areas Ltd are developing a proposed expansion to its Cosmic Boy concentrator to treat an impurity stream, that is high in nickel and would otherwise report to tails. Through the use of BioHeap® technology Western Areas aims to recover the nickel and discard the arsenic to tailings. This expansion will consist of a biohydrometallurgical plant that leaches the nickel arsenic minerals, removing the arsenic as a stable iron/arsenic hydroxide, while recovering the nickel as a high-grade nickel sulfide product (at approximately 50 per cent nickel). This can then be blended with final concentrate to improve nickel grades and recoveries, while simultaneously reducing impurity levels or used to produce high value products like nickel sulfate.The introduction of a small microbial leach plant may be beneficial to base metal concentrators constrained by impurities or grade.Citation:Fewings, J, Seet, S, McCredden, T and Fitzmaurice, C, 2016. BioHeap® - Breaking the Grade/Recovery Curve for Nickel Concentrators, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016