Search Documents

By I Doye

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals responsible for highly acidic, sulfate and metals-rich drainage. Several methods of mine waste management have been developed that reduce liabilities on environment. Layered co-mingling of waste rock with compacted tailings, covers with capillary barriers effect, and co-disposal of waste rock and tailings are these new methods which are used to reduce the formation of acid mine drainage. These methods shield waste rock dumps from oxygen. These techniques could prevent oxidation reaction. In this study, alkaline industrial wastes are used with acid generating tailings to inhibit acid mine drainage. The alkaline wastes selected are cement kiln dust (CKD) and red mud bauxite (RMB). These alkaline materials are used to keep neutral conditions in the fine material layer and to inhibit the metabolic activity of Thiobacillus ferroxidans which catalyses the oxidation of sulfide minerals. A series of timed static leaching tests were performed by reacting samples of mine tailings with two, five and ten per cent alkaline material in order to characterise geochemical balance between liquid and solid phases. Column tests have been set up with oxidised tailings, waste rock, CKD, and RMB. Column tests have been carried out to simulate layered co-mingling, covers, liners, and co-disposal of waste rock and tailings. Column leach tests were conducted in order to investigate the long-term neutralisation potential of alkaline materials and the drainage water quality. Bacteria counting were performed on each sample after testing. The results obtained show that the addition of alkaline materials permit the retention of near neutral conditions in the fine material layer, thus increasing water quality and preventing bacteria development. In fact, the pH results show that the use of five per cent, ten per cent CKD or ten per cent of a mixture of CKD and RMB permit the retention of neutral pH conditions in the reactive layer. At these percent rates, the concentrations of Al, Fe, Cu, Zn, and SO4 in solution are significantly reduced compared to those obtained with the tailings only. In presence of waste rock, the relative position of the fine material layer is important. When the fine material layer overlaying reactive waste rock is composted of reactive tailings with ten per cent CKD and ten per cent (CKD:RMB), a delay was observed before achievement of near neutral pH. The neutral pH conditions remain stable over time. The mixture of CKD and RMB provides a better short-term neutralisation than the use of CKD alone. The use of alkaline materials is beneficial in order to reduce the concentrations of Fe and other metals such as Cu and Zn as well as the number of viable bacteria. The use of ten per cent RMB alone does not involve the neutralisation of reactive tailings. In the cases where the fine-grained layer are below or mixed with the waste rocks, the near neutral pH values are directly reached with ten per cent CKD. However, the pH values decrease rapidly and the number of viable bacteria increases.

Jan 1, 2003

By Drew GJ

Smelting is a process in which heat is applied to ores to produce metals. Impurities are removed by segregation in the slag, or converted to gases or sublimates and discharged up the flues. Mate- rials delivered into the smelter have generally been previously concentrated or processed at the mine, and the size of their particles, and also their chem- ical composition, greatly affect the smelting proc- ess. Some impurities are more difficult to remove than others, and are more objectionable in the finished product. The first metal mine in Australia was opened near Glen Osmond in South Australia in 1841, for silver-lead ore. It was followed by the Kapunda Mine for copper in 1844 and by the very signifi- cant Burra Mine, also for copper, in 1845 (Figure 1). A major part of their ores could not be exported profitably for smelting in England and Wales where the large smelters were then located. In addition to treating ores from Cornwall these also smelted ores from recently opened mines in Cuba, Chile, and Mexico. The Welsh smelting process (Figure 2) was developed over a period of years to utilise Welsh coal to treat copper ores particularly from Corn- wall. The first step consisted of a calcination to remove sufficient sulphur from sulphide ores so that subsequent melting operations would produce copper matte, a copper-iron-sulphide which melted at about 1050¦C. Subsequently refined to white metal with the addition of carbonate and oxide ores when these were available, and often through an intermediate step of blue metal, this matte was finally oxidised to pure copper, or as pure as it could be made in those days. The movement of metal towards greater purity was matched by a reverse flow of slag, carrying reducing quantities of copper, so that the slag rejected from the first melting process carried the minimum quantity of copper. Chemical analysis was virtually unknown. Materials were assayed in the laboratory by a small scale smelting process, and the purity of the final refined copper was judged b} the ease with Mhich it could be hammered into thin sheets.

Jan 1, 1987

The underground mining of a narrow vein hard rock orebody is a capital and labour intensive method of extraction. Due to the nature of underground mining it is difficult for higher level managers to physically see the efficiencies and inefficiencies of a particular method. Extraction methods and sequencing often need to be altered from the original planned methods as a result of mine developent, providing more in depth information as it progresses. As a result of these issues contract mining of these orebodies is common practice. There are several types of contract structures for the purpose of underground contract mining with many complex permutations of them that reflect the different needs of each individual company and orebody. The different contracts are arranged dependent on the mining companyÆs desire to transfer or, alternatively, embrace risk. This presentation gives a brief overview on these different methods and their various advantages and limitations with regard to small scale and narrow vein underground mining. With respect to these different contracting methods, the presenter reviews the mutual growth benefits of emerging partnering opportunities, specifically with regard to smaller explorers exploring and developing prospective mining tenements. The specific advantages to small explorers include the resource flexibility and speed of project development that private mining contractors can provide. Given the contracting methods that are available, there is potential for small private mining companies to gain minor stakes in major projects and major stakes in medium sized projects by employing innovative contracting solutions to provide mutual benefits to the parties. Some potential scenarios to this effect are suggested in the presentation. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

By Manca PP, Lassandro R, Caranassios A, Massacci G, Ciccu R

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables on tool performance (cutting rate and bead wear) has been Elucidated.

Jan 1, 1992

By Kato Y

As a direct result of the Mining Industries need to improve efficiency and production in Open Pit type operations, the size of haulage units have increased dramatically. This trend has continued such, that the majority of dump trucks operating in Open Pit operations are in the 170 ton class. Continued mining in existing locations has meant that the increase in vertical lift and resultant grades, and increases in hauling distances are making electric drive systems unsuitable. This is largely due to the electric drive systems heat limitations on major propulsion components. With these mining requirements in view and the present limitations on electric drive systems in mind, Komatsu have been developing the Komatsu HD1600M. A diesel powered mechanical drive dump truck capable of operating in deep pit operations. This presentation introduces: Komatsu HD1600M Dump Truck

Jan 1, 1982

By Andersen AK

As part of a research program sponsored by Continental Copper and Steel Industries, Inc. (cos), investigations have been conducted by the Colorado School of Mines Research Foundation, Inc. to study the effect of high current densities on electrolytic processes. The importance of high current densities has long been recognized, particularly in the deposition of copper, and the results of considerable research on the subject have been reported in recent years (19 29 39). This is not surprising because, besides plant capacity, current density is the other major factor which will determine the process economics. In the production of electrolytic copper, current efficiency, steam consumption, number of cells, building area, metal inventory, cathode purity, and power consumption are all affected by current density. The ability to maintain a high current efficiency and satisfactory cathode purity while increasing the current density to twice or three times that commonly practiced could result in considerable saving of capital investment and reduce the operating cost per ton of metal produced. The optimum current density i.e., that current density of which production cost would be at a minimum, can be established from an analysis of the various inter- relating factors (49 59). A review of.all operating electrolytic plants (electrowinning and electrorefining) will indicate that most of these plants are operating at 50% or less of the optimum current density (6). One of the reasons for not using the optimum current density may be attributed to the fact that conventional electrolytic tank- house equipment does not perform satisfactorily at high current density operations. Various investigators (19 79 8) have attempted to overcome this limitation by modifying the design of the electrolytic cell, virtually unchanged since it was first introduced in the late 1800's. Previously, these attempts have not resulted in,a cell design suitable for commercial application. However, recently, a cell has been designed which performs efficiently under such conditions. This is a CCS development (patents applied for).

Jan 1, 1969

By Morley C

The Mount Charlotte gold mine is located 0.75 km east of the General Post Office in Hannan Street, Kalgoorlie WA and about 3.5 km north of the Fimiston Operations on the famous Golden Mile.Mechanised underground bulk-mining at Mount Charlotte has been in continuous operation since 1963. For the 30-year period ending December 1992, the mine produced 22 million tonnes (Mt) of ore for a recovery of 2.73 million ounces. During 1991/92, the mine produced 1.53 Mt of ore at a head grade of 3.15 gramshonne (g/t) for a recovery of 135 822 ounces.The principal ore source at Mount Charlotte has been the Charlotte Orebody which is now largely mined out. Since 1990, approximately 75 per cent of production has been sourced from the Reward Orebodies. The Charlotte Orebody was a relatively homogeneous quartz stockwork with simple geometry and average bulked grades in the range of 4.0 to 5.5 g/t. This is in contrast to the Reward Orebodies and the more recently defined Charlotte Deeps and Maritana Stockworks, which have complex grade distribution and geometry with lower average bulked grades (2 to 4 g/t). The lower grades are principally due to the decreased density and volume of stockwork venation and related vein halo alteration. Typically, these stockworks comprise a patchy mosaic of quartz veins and vein swarms, with irregular distribution and geometry within the quartz gabbro host rock.

Jan 1, 1993

Determining the environmental consequences of green field projects is becoming an increasingly important component of new projects. Feasibility studies are regarded by potential investors as incomplete if a comprehensive Environmental Impact Assessment (EIA) has not been completed. These EIAÆs need to meet various local and international requirements in order to achieve bankability. Heavy mineral mining projects are often located in ecological sensitive coastal zones, and bring with them a suite of social impacts in the mainly developing countries within which they are usually located. This paper draws on experience gained in undertaking EIAÆs for heavy mineral mining projects in Kenya, Mozambique and South Africa, and uses these case studies to identify potential pitfalls. Important lessons include the need to initiate the EIA process as early as possible in the project, in order to develop management systems to mitigate the environmental impacts of exploration. Close and on-going consultation with affected communities is also seen to be critical to the success of the EIA. Proactive participation on the part of the environmental consultants with the project team and all interested and affected parties (IAPs) is important. An EIA commissioned later in project planning makes it difficult for the EIA to contribute in a positive manner to the project. Early engagement with environmental consultants allows the environmental assessment to develop from a report to an actual process, and to become fully integrated with project planning. The proviso is that an initial æfatal flawÆ assessment is required to identify any potential æshow stoppersÆ, in order to meet one of the important objectives of EIA, namely an assessment of whether or not the proposed project is the preferred development intervention in the study area. For more controversial proposals this may require the commissioning of a Strategic Environmental Assessment (SEA), which circumvents some of the limitations of the project level EIA. Whilst confidentiality is a constraint to full disclosure, an open participatory approach to public consultation is essential to add credibility to the EIA process and to gain, at least, the acceptance of the process from the majority of IAPs. Full disclosure is encouraged by organisations such as the International Finance Corporation, who acknowledge that good public consultation costs a lot of money, but bad public consultation costs a lot more! An open approach to disclosure presents understandable difficulties for proponents, as they are required to give up some of their control over the project, and to trust the social scientists engaged in the process. However, independence in the EIA process is critical to its success. This paper will highlight these and other issues by drawing on five case studies to identify lessons learnt, and explore the above themes in more detail.

Jan 1, 2001

By H Ramandi, H Masoumi, I Canbulat, B Hebblewhite, J Oh, S Saydam, W Timms, S Mo

This paper reviews the floor heave mechanisms in underground coal mine roadways. Previous studies have reported three main failure mechanisms: bearing capacity failure, buckling and swelling. The buckling failure has been observed where immediate floor strata are relatively strong and thinly bedded. On the contrary, the weak floor strata have been associated with both the bearing capacity failure and swelling mechanisms. The bearing capacity floor failures are likely to induce other types of instability such as pillar punching, tensile failure of pillar, roof fall and subsidence as well as floor heave. Despite a considerable amount of research, predicting the magnitude, location and timing of floor deformation is challenging with current state of knowledge. CITATION:Mo, S, Ramandi, H, Oh, J, Masoumi, H, Timms, W, Canbulat, I, Hebblewhite, B and Saydam, S, 2018. A review of floor heave mechanisms in underground coal mine roadways, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 196–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Grigorescu, J H. Hodgkinson, M Khanal

The mining industry often needs to operate in remote or climatically harsh locations. The industry has recently been forced to deal with extreme conditions including floods, heatwaves and droughts. As these are becoming progressively frequent occurrences, mines typically build ‘downtime’ into production schedules and expect to incur costs to manage the various risks arising from climate extremes. Importantly, many environmental conditions are becoming more extreme and consequently, risk management based on past data can become increasingly ineffective. Market and shareholder demand for fewer interruptions are another pressure on mines to avoid prolonged or frequent downtime. Hence, adaptation to climate is becoming an important strategic move for many companies, many of whom are using future climate scenarios and alternative risk evaluations.We present here a method that uses commonly available mine site data to assist decision-making for reducing vulnerability to sudden flood. The method, ‘climate-related adaptation from terrain evaluation results’ (CRATER), identifies a mine’s flood ‘hot-spots’ and presents them as a ‘traffic lights’ warning map. The process then requires a failure analysis process such as fault-tree analysis to identify both the cause of possible failures and a range of possible failure-avoidance adaptations. In the final stage, management can assess the most suitable option for the mine, based on the availability of capital such as time, facilities, labour and money in addition to social acceptability of the options. CRATER has been tested in an open cut mine environment and is now being further developed to identify how subsidence over underground mines may impact on flooding and ponding over the mining life cycle (CRATER II). Further work is continuing to test larger and more complex mine landscapes to deliver a method to extract more knowledge from existing data.CITATION:Hodgkinson, J H, Grigorescu, M and Khanal, M, 2016. Reducing mine site extreme rainfall vulnerability using climate-related adaptation from terrain evaluation results, in Proceedings International Mine Management Conference, pp 187-200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Vink L, Johnson N. W, Mackenzie J, Young M. F, Johnston M, Landmark V

The influence of ore textures on metallurgical behaviour is poorly understood for most ores. An alternative method for characterising ore textures and for determining the resulting implications on ore processing has been developed for the Geor

Jan 1, 1998

The green field discovery of a two million ounce high-grade refractory gold ore deposit in the Indonesian Province of Sulawesi Utara, led Newmont to utilise its proven technical expertise in dry grinding and whole ore roasting to develop a 2000 tonne per day, 160 000 ounce per year operation in this remote and picturesque location.Located at an elevation of 250 in above sea level and ten kilometres to a deep water natural harbour, the hard rock open pit mine, process plant and infrastructure facilities were built to budget at a capital cost of US$132 million. The plant was commissioned with oxide ore, with the first gold poured in March 1996 and with refractory ore in January 1997. The operation rapidly met its production targets because of extensive forward planning and training programs developed for the local workforce. The presence of steep topography, fertile coastal plains, high rainfall, high seismicity of this location led to the decision to dispose of neutralised tailings in deep water off the coast instead of impounding tailings in a dam. This paper describes the development of the project and the challenges in developing a gold operation in a remote location which lacked infrastructure, the steps taken to ensure a smooth commissioning, and the selection of the workforce to operate a technically sophisticated facility.

Jan 1, 1997

By G J. Wilkie, P A. Revell

The R&D landscape for ore pre-concentration technologies within mining is characterised by the development of individual technologies and point solutions. This presents METS and mining companies with the combined challenge of understanding how to apply pre-concentration technologies to create maximum value, and how to sustainably integrate the technologies into their businesses to maintain the value. The paper will consider the requirements of an integrated pre-concentration system and presents a portfolio of R&D projects that have co-developed and integrated a suite of new precencentration technologies and methodologies across the mining value chain. Focus areas include in-situ orebody characterisation, blast design, real time cross belt mineral sensing, and consideration of how much data needs to be acquired in order to make value based decisions between ore pre-concentration options. An ore pre-concentration workflow is presented to demonstrate how additional optimisation opportunities are enabled both by moving decision points further upstream in the value chain, and by integrating the concepts of pre-concentration into the design of mineral processing equipment. Additionally, several research projects examine the non-technical factors that present barriers to uptake of new technologies within mining companies. Organisational culture, risk management and socio-political factors are discussed and a set of management tools are presented that allow organisations to self-assess their readiness for new technology uptake, along with process models to assist management with identifying and navigating the ecosystem of stakeholders that are decision makers in the use of pre-concentration technologies.

Nov 10, 2020

The Tom, East and West zone, stratiform Zn-Pb-Ag deposits at Macmillan Pass, Yukon, Canada were discovered by Hudson Bay Mining and Smelting Co Ltd prospectors in 1951. Further exploration, including two phases of underground exploration produced an HBM&S calculated reserve of 9.28 Mt of 7.5 per cent Pb, 6.2 per cent Zn and 69.4 g/T Ag for these zones. Cominco Ltd optioned the property in 1988. Deep, surface drilling extended the West and Southeast zones downward 200 - 300 m, indicating an additional potential resource of several million tonnes of good grade. The magnitude of the controlling syndepositional setting suggests that mineralisation continues to greater depth but with increased drilling and possibly mining costs. The 30 x 60 km Macmillan Fold belt trends WNW across the NW Selwyn Basin and Cordilleran trend. Within the fold belt, the Central Block - a complex, rift controlled basin of Devonian siliciclastics, hosts seven zones of Pb-Zn-Ag mineralisation clustered about four hydrothermal centres. The centres, distributed over 24 km, are coincident with small syndepositionally active structural sub-basins. The Tom deposits, in one such sub-basin, are localised by a third order structure consisting of two palaeobathymetric troughs flanking a syndepositional horst. This structure caused drastic facies and thickness changes over 600 metres of strata and focussed the venting of hydrothermal fluids through permeable conglomerates in the horst and its flanking growth faults. Mineral facies are zoned, with Pb-Ag contents rapidly diminishing outward from the vent resulting in restricted areas of high grade Pb-Zn-Ag-Ba ore within more extensive, sub-economic, Ba-Zn mineralisation. Widespread iron carbonate alteration of the footwall and high Si, B and Zn values in the hangingwall 'fingerprint' the deposit and along with the distinct facies variations provide aids to exploring the Tom and like deposits.

Jan 1, 1993

By E Nettleton, A Melkumyan

Identification of geology and mineralogy in situ on the mine face is essential if mining processes are to be automated for tasks such as exploration, grading and reconciliation. Hyperspectral data acquired from field based platforms are ideally suited to these tasks, and are set to revolutionise the automated mining industry. Changing conditions of solar illumination introduces variation into the hyperspectral signal, which is unrelated to geology, complicating analysis of data. Thus, algorithms must be able to deal with changing illumination conditions and operate in a consistent and probabilistic framework, which is a prerequisite for data fusion with other sensors. To produce accurate classification maps of geology, algorithms must be developed that are effective under different conditions of illumination.The efficacy of three algorithms to classify hyperspectral data for geology mapping on vertical mine faces was assessed. These algorithms are the spectral angle mapper (SAM), and two machine learning methods operating within a fully probabilistic Gaussian process (GP) framework û the squared exponential (SE) and the observation angle dependent (OAD) covariance functions (kernel). Two experiments were done to assess the classification performances. The first determined the performance of the algorithms by classifying hyperspectral data of known rock samples acquired using a field spectrometer. The GP-based methods had a similar performance, with average accuracies and F-scores of 97 and 88 per cent (GP-OAD) and 95 and 81 per cent (GP-SE), respectively. Average accuracies and F-scores for SAM were significantly smaller (80 and 40 per cent respectively). The algorithms were then applied to hyperspectral imagery acquired from a vertical mine face at different times of the day, under very different conditions of illumination. In contrast with experiment 1, SAM and GP-OAD gave results which were superior to GP-SE and were entirely consistent with geology mapped in the field. Compared with SAM, GP-OAD was less sensitive to the effects of shadow and produced classified images that were less noisy. The GP-SE method failed to delineate even gross changes in geology on the mine face. These results show conclusively that in order to use independent training data (spectral library) to classify imagery acquired under a different set of conditions, algorithms must take into account variability in incident illumination. Measures based on spectral distance are inferior to those based on spectral angle.The OAD kernel within the GP framework (GP-OAD) is superior to the other two methods because:it provides a probabilistic framework;it is insensitive to variability in illumination within and between imagery acquired under different conditions; andit can identify and map geological zones on a vertical mine face using an independent spectral library, without a priori knowledge.

Sep 26, 2011

By T Blyth, D Holden, N Archibald, S Huffadi

The Morning Star mine is owned by Hill 50 Gold NL. Gold is hosted in quartz-carbonate ¦stibnite ¦molybdenite veins that occur in a series of deformed, altered and metamorphosed mafic volcanics with subordinate sediments and felsic intrusive rocks. The irregular gold distribution and its relationship to structure and alteration intensity makes the definition of stoping limits difficult. Understanding the structural evolution of the orebodies and the contemporaneous and later structures that affect the orebodies has been very useful in this context. This paper reports on a detailed mapping exercise (as part of a more extensive and on-going investigation) and the integration of this mapping with other geological and grade control data in a 3D modelling environment to provide an expanded basis for stope design. Three types of mineralised zones can be discriminated based on the morphology of the veins within. They are:those associated with strongly folded, thick veins (approximately 1 m thick eg 05 orebody); those comprising planar, boudinaged and some folded veins which consolidate to form tabular, steeply dipping bodies (eg 010 orebody); and zones containing the above vein types and thin, highly deformed veins within zones of intensely foliated country rock that result in localised, irregularly distributed high-grade gold zones (eg 02 orebody). The mineralised zones associated with thick folded veins are typically predictable over many tens of vertical metres. The second and third types of ore zone is generally less predictable. Detailed mapping and structural kinematic studies indicate all ore zone types are affected by progressive deformation involving strong strain partitioning. It is interpreted that high strain zones, recognisable by intense foliation development and highly deformed veins, are the latest stage of a progressive deformation which approximates bulk flattening. Structural controls on mineralisation can be defined at two different scales.Regional scale folding has deformed a sequence of mafic volcanics with interlayered sediments and felsic intrusives. Initial geometry of felsic bodies relative to orientation of the primary lithological layering and the bulk shortening direction is interpreted to be critical for initiation and development of strongly dilatant zones within this package of rocks, and Local scale dilation is evidenced by development of several vein sets whose range in orientations and opposed vergence relationships suggest a pre-folding origin comprising both extensional and hybrid shear-extensional types. Continued deformation resulted in folding of these veins with strong strain partitioning. Major vein packages are closely spatially associated with the felsic/mafic contact and an interpreted early structure which appears to have partitioned early dilation. This structure is now obscured by strong deformation but is currently represented by a zone of planar veins.

Jan 1, 2000

By M J. Gillespie, P D. Erskine

Mine site rehabilitation generally includes the re-shaping of overburden to create a final landform, manipulation of substrates and subsequent revegetation. Due to the wide range of environmental variables that influence rehabilitation progression, having clearly-stated final land-use goals and ongoing significant contributions to the planning process, from prefeasibility through to mine closure, is essential for achieving stable landforms and sustainable rehabilitated communities. Two examples of rehabilitation processes in the phosphate rich region of North West Queensland are used to illustrate some of the possible benefits of early planning and communication of rehabilitation requirements.Approximately 160 km south of Mount Isa, Incitec Pivot Limited operates a 35 year old open cut mine at Phosphate Hill. Monitoring of rehabilitation areas and selected analogue sites is undertaken annually, but the initial landform design, substrate management and species selection has created a difficult environment for revegetated areas to successfully establish. Constant management input (such as weed management, erosion control, supplementary seeding, etc) will, therefore, be required over a long time frame.The second example uses exploratory drilling and historic costean pits at Legend International HoldingÆs Paradise South site, 135 km north of Mount Isa, to determine the success of natural vegetation colonisation on waste rock and compacted soils, and the effects of cattle grazing on recolonisation. This information can be used by planners of the mine life to inform possible end-land use decisions and proposed completion criteria.In a semi-arid environment such as North West Queensland, the creation of a post-mine landscape suitable for nature conservation and/or grazing can be an arduous task. The input from environmental personnel at all stages of the mining process will positively impact upon the quality of the resulting rehabilitation and ensure undesirable legacy issues are minimised.CITATION:Gillespie, M J and Erskine, P D, 2012. Importance of early rehabilitation planning - Case studies from North West Queensland, in Proceedings Life-of-Mine 2012 , pp 187-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By E Villaescusa, C Drover

The stability of access tunnels is one of the main engineering challenges in deep underground mine construction. Many underground hard rock mining operations are now reaching depths where the induced stresses are such that sudden and violent failure of the excavations can occur very soon after construction. The loading conditions on the installed ground support schemes are often underestimated by conventional engineering design methods. Therefore, the actual loading conditions often exceed the installed ground support capacity. This can result in failure of the excavations and, in extreme cases, potentially closure of mining operations amounting to hundreds of millions of dollars in lost production. More frequently, violent excavation instability at great depth causes operational delays, costly and unplanned rehabilitation, as well as risks to worker safety. In order to address this challenge, this paper briefly summarises a modern, innovative approach to the design and construction of mine development at great depth. The process follows seven main steps. The first step is to characterise the rock mass strength, structure and stress. The second step is a stability assessment, which identifies the plausible modes of excavation failure, based on the rock mass characterisation. The third step is the definition of an excavation geometry which is harmonic to the high stress conditions. The fourth step is to prepare a site-specific face destressing drill and blast design which will reduce the potential for rock mass instability during the development construction cycle. The fifth step is to accurately quantify the expected loading conditions on the installed ground support. The method of doing so is uniquely analytical and probabilistic. It is based on the natural mechanical relationships between rock strength, structure, induced stress and the physical characteristics of the instability, including its mass and ejection velocity. The sixth step of the design process is to specify a ground support scheme arrangement with sufficient strength and displacement capacity to exceed the rock mass demand by a safe margin. The final stage is to install the complete ground support scheme using mechanised technologies which minimise the exposure of the equipment operators to unsupported ground at the tunnel face.

Nov 29, 2022

By J Liu

In situ coal gasification is a method of extracting a high proportion of the energy value from coal without the need for mining. In situ conversion of coal to combustible gases is achieved by drilling wells into the seam, injecting gasification agents and initiating combustion. The product gases are then extracted to surface using production wells. These gases are clean energy sources for power generation, heating or synthetic fuel production. In situ coal gasification is of particular interest with respect to its lower environmental impact, potential application to otherwise inaccessible energy resources (ie offshore, deep deposits or beneath protected lands) and low capital intensity. Practical application of this clean technology is restricted primarily by lack of satisfactory quantitative descriptions of the processes involved, in particular the hydromechanical processes.In this study, three characteristic physical zones of an in situ gasifier are identified as the rubble zone, combustion front and virgin coal zone. Coupled mechanical processes of coal consumption and overburden collapse are used to describe the permeability profile in the rubble zone. Additionally, the redistribution of overburden load associated with coal consumption is accounted for with the formulation of a stress (compressive) dependent permeability profile, which is applied to the virgin coal zone. The model was implemented into and solved by FEMLAB, an advanced computer simulation tool. The flow process, according to DarcyÆs Law, is subsequently described in terms of permeability dependent injectivity. Injectivity is an indicator of flow velocity, which has been identified as a crucial factor in determining the commercial value of product gases from in situ coal gasification. The stress alteration to coal permeability was found to have a dominating influence on the flow process. This finding implies that a greater understanding of the in situ coal burning induced deformation of surrounding rocks would be of significant value in assessing the economic viability of applying this clean technology to potential sites.

Jan 1, 2004

By White L. R, Boger D. V

The paper describes the surface chemistry and particle physics that control the fundamental flow properties (Theology) of mineral particle slurries. We further address, through a series of case studies, the design data that emerges from experimental studies of the flow properties of complex, high volume fraction mineral slurries. The case studies are drawn from mineral oxide concentrate processes, tailings dewatering operations and from filter cake production and management. The paper emphasises the essential links between design of process slurry handling systems and the control of the flow of such slurries by control of the pulp chemistry.

Jan 1, 1992