Search Documents

By M Ljunggren, M Lundh

Dissolved air flotation (DAF) in wastewater treatment as a separation process of submillimetre biological flocs is based on the generation of bubble/floc aggregates. DAF is a complex process but has got advantages, such as allowing a high hydraulic load, compared to sedimentation. A thorough knowledge of the physics of the DAF process is, however, still lacking. This paper will present results of experimental studies on three aspects of significance to the separation process û the flow structure in the flotation tank, rise velocities of aggregates, influence of floc size on the separation efficiency. Flow structure. Measurements were performed in a pilot plant mapping and visualising the velocity field. The dispersion water (bubbles) had a decisive influence on the flow structure due to the effect of the bubbles on the bulk water density. Stratified conditions with a less dense, bubble-containing upper layer and a clear water, denser bottom layer were important for a good separation. A simple model of the stratified flow structure was elaborated making it possible to interpret the function of the aggregate rise velocities. Bubble/floc aggregates. The dynamics of single flocs, bubbles, aggregates were visualised using a borescope + CCD video camera + digital recorder + image analysis. Sequences of video frames made it possible to determine the rise velocities of the single aggregates. These velocities were found to be in the range 1 - 9 mm/s with a tendency for large flocs to have higher rise velocities. Separation versus floc size. The floc size distribution was measured in the DAF process. Data from three different DAF cases showed, that large flocs (> about 100 ¦m) were entirely separated, whereas small flocs experienced a less good separation. It was, moreover, found, that a very significant separation of flocs took place in the very upstream end of the separation zone in a pilot plant case.

Jan 1, 2005

By P Bethune

Back Creek is a tributary of the Condamine River. It flows in a northerly direction across the existing Commodore coal reserves. The diversion of Back Creek was proposed to minimise sterilisation of the reserves. The approval process required a Waterworks Licence application, under the Water Resources Act 1989 (Qld), for the construction of a stream diversion channel and floodway. The diversion was designed using the æreference reachÆ approach, which mimicked existing properties of Back Creek. The following design standards were developed for the diversion: the diversion corridor width was 500 m; the diversion geometry was specified for both the low-flow channel, and the floodplain; material properties were specified for both the low-flow channel lining and the diversion bund; compaction standards for both the low-flow channel and floodplain were set; and the diversion rehabilitation included a riparian corridor and pasture land with clumps of native trees and shrubs. The following performance criteria were developed for the diversion: velocity regimes were replicated for the design events considered, in an attempt to avoid increasing the diversion flow velocities in comparison with the existing creek flow velocities; sediment transport calculations indicated that no significant change in sediment transport was expected within the diversion; overburden settlement estimates for the spoil placed in the corridor were summarised, and will be monitored throughout the construction process; geotechnical stability of the proposed Eastern Pit Buttress and the diversion bund configurations was confirmed; and groundwater impacts were assessed. Construction techniques, monitoring and further investigations are also discussed in this paper.

Jan 1, 2003

The evolution of the Oaky Creek mining complex provides a good example of the mining cycle in practice. Oaky Creek has been innovative in its choice of mining methods, with virtually the full range of coal mining methods having been used as workings have progressed down dip. The history of the mine is traced through its development (and ownership changes), progressive selection of mining methods as depths of cover to seams being mined have increased, and rehabilitation. This allows the different mining methods to be described and illustrates the concept of æwall-to-wall miningÆ.

Jan 1, 1998

By G Lane, S La Brooy

A century ago, new mines were often accompanied by smelters. In Australia, smelters were built at the Daydream mine near Broken Hill, at Kuridala and Mount Elliott near Mount Isa, Broken Hill, Mount Lyell, Mount Morgan, Mount Isa, and more recently at Tennant Creek, Kalgoorlie and Olympic Dam. Now the big miners eschew site-based processing in favour of shipping concentrate to smelters in Europe and Asia. As Chip Goodyear was in the process of vacating his leadership role at BHP Billiton, he was quoted as saying that BHP should concentrate on mining ore and leave æto others the skill set of processing that materialÆ. Yet there are times when on-site processing clearly makes sense. Few companies ship gold ore or concentrate to China for gold extraction. New smelters are being built in Zambia. Solvent-extraction and electrowinning plants frequently produce copper from oxide ores and concentrates while pressure leaching is increasingly being considered for copper sulfide ores. Some argue that on-site processing is best because the waste products can be returned to the ground from whence they came, avoiding potentially large disposal costs in more-populated areas. Copper treatment and refining charges will not remain at $45 per tonne and 4.5 cents per pound forever. This paper examines when it makes sense to use on-site pyro- or hydrometallurgical processes in todayÆs environment and comments on how current trends might alter the balance in future.

Jan 1, 2008

TSG Consulting works with many of the major global mining companies using simulation modelling as an integral component in their development teamÆs processes to determine which combination of infrastructure options, operating performance and operating rules best achieve project goals. All systems can be divided into a series of subprocesses. Conventional management and design practices focus on the optimisation of these system components. However, the interaction between subprocesses means that improvements made to the individual components do not necessarily translate into total system performance improvement.TSG Consulting advocates a ætotal integrated system approachÆ to understanding the behaviour and performance of complex interacting systems. In a constraint-based integrated set of processes, the instantaneous system capacity is limited by the subsystem component capacity that is the bottleneck at that point in time. Additionally, real world stochastic and dynamic influences tend to have knock-on effects across subsystem boundaries. This necessitates the requirement for simulation modelling to develop and validate solutions that are sufficiently robust to deliver sustainable outcomes. The key to maximising production is to understand the causes and effects the inherent variability has on component performance, subprocess performance and most importantly, the total integrated system performance. The correct use of simulation modelling techniques allows study teams to evaluate the relative merits of different capacity enhancement proposals. Put simply, when done well, simulation modelling provides a quantitative and rational process to enhance the knowledge and insight needed to make informed decisions.

Jan 1, 2007

By M Delaney

Alliancing is a contractual relationship in which organisations with an interest in a project are brought together in an atmosphere of co-operation to produce superior results to benefit all of the participants. Fundamental to the concept is the management of the risks associated with the project. The traditional risk management strategy adopted by clients has been to transfer this risk to others in the belief that this will result in the lowest overall project cost. It is assumed that competition in the market place will allow these risks to be transferred without paying a premium. However, this approach often results in the development of an adversarial climate, a high level of litigation, time and cost overruns and an overall poor project outcome. Under an alliancing arrangement the parties (client, designer and contractor) are aligned through shared interests in the projectÆs success by linking profitability to performance. Under such an arrangement, an atmosphere is created whereby the participants are motivated to focus on cost-savings, pursue best value and to innovate. Successful alliancing can result in highly motivated project teams and realisation of extraordinary productivity and cost-savings flowing from increased efficiencies. The situations in which alliancing can be successful are discussed with particular reference to the Wandoo Alliance which successfully completed the $375 million Wandoo B offshore oil platform in record time and with considerable savings to the project budget.

Jan 1, 2000

A review of publicly available coronial inquiries into fatalities that have occurred within the resources sector since the year 2000 reveals that a loss of corporate memory has been a contributing factor in 40 per cent of these accidents (National Coroners Information Service, 2010, Appendix B). With the highest levels of employee turnover within the Australian economy, increasingly complex operations and an ageing workforce, the management of corporate memory within the Australian resources industry poses a significant and often unrecognised safety risk.    The North Parks airblast of 1999 is used as a case study to highlight how corporate memory loss poses a significant hazard to resources projects and how such incidents will continue to occur if corporate memory is not effectively managed. Best practice from other industries is discussed to demonstrate how knowledge management systems can effectively work. This paper discusses how systems can be put in place within the geographically diverse resources sector, and how at the heart of any knowledge management system a culture of knowledge management needs to exist within an organisation.   The paper then discusses the importance of retaining key personnel and utilises findings from primary survey data collated in 2009 to show the size of the retention problem within the industry. From the data possible solutions to retaining key staff are proposed.   Finally the large and increasing role of contractors and consultants within the industry is discussed and methods of managing their knowledge are proposed.

Jun 1, 2010

Exploring for deep shallow dipping orebodies can be very expensive and very difficult. Surface exploration is often not an option and obtaining the best location for underground drilling can cause production delays if drilling is carried out from development headings. The Otter/Juan mine has been in production for approximately 34 years. All of the production is now sourced from more than 1000 metres below the surface from an area known as the Edwards Lode. The orebody is shallow dipping and open at depth. Exploration drilling has been performed from decline stockpiles and from hangingwall drill drives. Drilling from footwall positions (eg decline stockpiles) into shallow dipping orebodies can often produce intersections which are unusually thick thus leading to optimistic resource figures. The decision to develop a dedicated hangingwall drilling position can vastly improve the quality of the data used to generate an orebody model. In 1997 a new extension to the Edwards Lode was discovered and named the æFÆ surface. In 1999 a resource calculation was performed using data obtained from drilling that was carried out from decline stockpiles. In 2002 a dedicated drill drive was developed into the hangingwall of the æFÆ surface to obtain better data to verify the previous resource calculation. For this case study obtaining more representative data reduced the resource estimate by 66 per cent. This information was obtained early enough to allow for alteration to the mine plan and without loss of capital.

Jan 1, 2003

Deposits of manganese oxides and silicates in the Tamworth area were re-examined. The major deposit at Danglemah consists chiefly of rhodonite and the rare silicate tephroite. It is considered that the manganese was deposited with the original sediments, the silicates being formed later during the intense folding and low-grade metamorphism of the enclosing rocks.INTRODUCTIONMany small deposits of manganese oxides and silicates occur along a belt of eastern New South Wales and Queensland.Some fifty occurrences, most of which have been subject to mining activity, were described by Lloyd (1943) and some of this information was summarized by Knight (1947). The ores have been mined on a small scale since 1884. Small supplies of battery grade ore were won from a number of deposits, while larger quantities of metallurgical grade were sold to the steel industry. Maximum production was in 1918, when 6,500 tons were mined.The siliceous nature of many of the ores and their occurrence in the neighbourhood of granite batholiths led earlier investigators to consider the deposits to be of hydrothermal origin, associated with the granite intrusions. The present work questions this viewpoint.In this investigation, three of the chief deposits in the Tamworth area were seen. These were at Danglemah, which is being mined at present, and Mount Jasper and Manganese Mountain, which were mined in the past. The Danglemah mine is the most accessible and yields the best material...

Jan 1, 1962

By P J. A Lever

This paper presents details of CRC MiningÆs work with waterjet assisted blasthole drilling. The objective of this work was to investigate techniques that reduce the cost and increase the productivity of blasthole drilling. The focus is on a technology that uses a high pressure waterjet to assist the conventional rotary rock cutting action of a tricone drill bit. The potential benefits of this technique are increased productivity, reduced drill bit wear and reduced hole deviation and hence improved quality of drilling. This paper describes the results of a laboratory based experimental program comparing conventional tri-cone drilling performance to the proposed waterjet assisted approach. Additionally, work has been completed looking at the more practical issues around the collection and sampling of drill cuttings and water recovery (recycling) when drilling with a waterjet. These studies have demonstrated that waterjet assisted drilling can significantly increase the rate of penetration over conventional rotary drilling. For the best-case experimental result, the relative improvement was over 40 per cent. More importantly, it is a starting point for examining alternative uses of the additional drill productivity obtained from waterjet assisted drilling. For example, increased drill productivity could be used to improve rock fragmentation by drilling a tighter blasthole pattern in the same time period. an existing drill fleet, then the drill fleet size could be reduced, or improved rock fragmentation could be achieved by drilling a tighter blasthole pattern within the same time period.

Jan 1, 2004

By Boehme PW, Gregory OR

The results presented here show quite definitely that in the system investigated the intensity of dispersion is enhanced by switching the flow entry from bottom to sides of the packed trough. Since there is no reason to suppose that this would not be true generally then it is not surprising that the blast furnace dispersion data of Standish and Polthier lie above the data for packed columns with bottom fluid entry. In fact, on the basis of the present results, blast furnace dispersion results can never equal standard packed column behaviour but must always be above these. The result that the intensity of dispersion in the trough model is higher closer to the side ports than away from them is at variance with that of Standish and Polthier blast furnace results. Aside from the obvious structural differences between these two systems, it is thought that the presence of raceways and the tortuous path of the gas flow in the furnace may provide an answer. Clearly this is an important difference in the behaviour of the two systems and further investigations designed to clarify the position would have significant practical value. This would also give an indication of how the furnace D/ud values may be decreased along the whole height - assuming of course that this result gives the best overall performance of the furnace. However, there is to date no knowledge whatsoever about this aspect of blast furnace Technology.

Jan 1, 1975

This paper is intended to continue the subject in the light of recent work, from where it was left at the conclusion of the discussion on the excellent paper by the late Mr. Noel Haszard. The position then obtaining is briefly summarised below:-The points which received general agreement at that time were:-'(1) That the gold occurs, probably in an elemental form, in a state of very fine division in the pyrite.(2) That the aim in roasting of Kalgoorlie flotation concentrates should be to obtain the maximum porosity possible. The gold tellurides were amenable to treatment with either a' solution of high lime and cyanide strength combined with fine grinding, or bybromocyanidation without re-grinding.(3) That a low roasting temperature is essential during the elimination of the first atom of sulphur, if the final calcine is to give a good extraction by cyanidation.(4) Even with the best temperature conditions of roasting then determined, and after a period of cyanidation of the calcines until no further extraction was obtainable, the lowest calcine residues obtainable were equivalent to approximately 1·8 dwts. per long ton, based on an original concentrate of pure pyrite.There was some division of opinion at the time as to whether the temperature of the later stages of roasting was significant, and also as to the reason why the initial roasting temperatures had so marked an effect.

Jan 1, 1939

By Stanton RL

Stratiform lead-zinc mineralization in the Soldiers Cap Group and Kuridala Formation of the Mount Isa Inlier is closely associated with iron-rich sedimentary units or "iron formation", and has many similarities to the Broken Hill deposit in New South Wales. Both the Soldiers Cap Group and the Kuridala Formation have been intensively explored for deposits of this type since the early nineteen- seventies. A mineralized belt of at least eight significant prospects has been identified, of which the Pegmont deposit is the largest and best known example. In most cases the mineralized horizons contain banded galena and sphalerite within a gangue of predominantly quartz-garnet- pyroxene-amphibole rock, sometimes containing a variety of other metamorphic silicates, and apatite. Chemically, the mineralized horizons are distinguished by higher than usual levels of one or more of total Fe, MnO, CaO and P205. Interpretation of patterns of mineral- ization within the belt is based on the Pegmont deposit, where a model of base metal sulphide deposition within restricted basins of iron-rich chemical sediment has been developed (Stanton and Vaughan, 1979). Broadly, the model envisages the deposition of higher grade lead-rich mineralization in the basin centre position, lower grade zinc- rich mineralization in a basin intermediate position, and much weaker copper-rich mineralization in a basin edge position. These three positions reflect a laterally continuous arrangement of silicate microfacies within the original iron-rich sediment.

Jan 1, 1984

By Y Yang

Despite the importance and usefulness of basicity in metallurgical slags, the optimum quantitative expression of it has remained elusive, partly due to the fact that the precise concept of basicity has not been properly clarified. The two basic approaches to the concept of basicity are the Lux-Flood, which perceives basicity in terms of the activity of the free oxide ion, aO2-, and the Lewis, which perceives basicity in terms of the ability to donate negative charge. The former has been almost universally adopted in the area of metallurgical slags, while the latter has been increasingly accepted in the field of glass chemistry. In this paper, some difficulties of the Lux-Flood approach are pointed out, including the need for indirect measures of aO2-, which have proliferated in recent years. Accordingly, it is suggested that the Lewis approach has a good deal to commend it, and that the quantification of it in terms of optical basicity is the best measure of basicity available, which should therefore be more widely applied in metallurgical slags than it currently is. The fact that there are intrinsic problems in evaluating the optical basicities for the transition metal oxides is acknowledged, and a new scale is recommended. The patterns of iso-optical basicity lines in ternary systems are shown to agree well with the pattern of iso-activity and iso-capacity lines under appropriate conditions.

Jan 1, 2000

By Johnson D. P, Beamish B. B

The northern Bowen Basin has a very large resource of coalseam methane gas-in-place - 136 TCF(7ohnson and White, 1988). The gas is pipeline quality, being 98-99 per cent methane with traces of carbon dioxide and higher hydrocarbons. The largest resource of natural gas within the coalseams of the northern Bowen Basin is contained in the Moranbah Coal Measures (75 per cent). The next most important resource is in the combined upper Fort Cooper (16 per cent) and Rangal (nine per cent) Coal Measures. The far northern parts of the basin have low gas contents due to the combined effects of limited extent of the coal measures, shallow depth and low rank. Reserves per well are more than double that of the best coalseam methane wells in any basin in the United States. In some areas of the Moranbah Coal Measures, the gas-in-place estimates exceed 225 million cubic metres per well (80-acre spacing). A distinction is made between resource base, as determined from this basin assessment, and the deliverability potential. Parameters used to estimate gas-in-place (coal area, thickness, density, rank and depth) can be adequately extrapolated from areas of high- to low- data density. Parameters affecting methane production (permeability, gas depletion factor and critical desorption pressure) cannot be generalised. Exploration and development programs must rapidly develop a predictive capability for these factors, on a local scale, through geological modelling and confirmation drilling.

Jan 1, 1991

The coastline is. an incomparable stretch of sea coast known as Ninety Mile Beach. Two gas pipelines and two oil pipelines carrying hydrocarbons from thb'Bass Strait fields to the markets of Australia cross this beach. They cannot be seen as they are laid in trenching stretch- ing many miles out to sea and the beach was restored to its natural state. Even where the dunes were disturbed, suitable grass was sown thus consolidating the sand and preventing erosion. Ninety Mile Beach is but one of the many key.wildlife and recreational areas that our operations must be concerned with. Others include Westernport and Corner Inlet, but the one discussed in this paper in particular is the platform area of the Bass Strait itself. Never was the old adage "an ounce of prevention is worth a pound of cure" more meaningful than in offshore oil production. All are well aware of some of the events of the past several years that resulted in large and costly oil spills. Far less is known, seen or publicised about the measures and developments that are undertaken to ensure that such events do not occur. We also have well developed plans for response in the event of an emergency situation, which can be initiated with great rapidity. Our responsibility is to ensure that with the best of engineering technology and operating procedures, spills do not occur.

Jan 1, 1971

Optimising drill performance has always been a primary goal of drilling and blasting managers. Improving drilling rates and utilisation will ultimately drive the cost per foot or metre downward. Additionally, more consistent production will ensure shovel or dragline performance goals are met and the chances of machine idle time is minimised. Over the past 20 years, many studies have examined rotary drilling factors and performance issues. In most cases a common theory points to energy input versus drilling output. Indexes such as specific energy and total work energy have been -developed to quantify the drilling process. As general engineering principles dictate, energy is required to drill rock by overcoming compressive and shear strengths. Concurrently, the greater the energy input, the faster the penetration output. Therefore, by examining the basic drilling energy parameters, optimisation is possible. The principles of rotary drilling are driven by five factors. When optimised individually and as a system, drill performance will improve. Most recent studies all agree that a performance relationship exists between bit load, bit rotation, and hole flushing. Additionally, proper bit selection and most of all, the operator, can have a tremendous effect on drill productivity. By analysing these factors and establishing the best case scenario, an overall drilling system can be engineered to match the mining characteristics. Furthermore, by balancing these factors, a lower cost will be achieved through increased production rates, maintenance costs, and effective drill utilisation.

Jan 1, 1995

By Meyer C. F

The increasing use of continuous miners in the extraction of high coal seams has amplified the need for enhanced ventilation systems in the headings. Owing to larger face dimensions and higher production rates, more ventilating air is required to effectively dilute liberated methane to acceptable concentrations. However, the increased air quantities raise and entrain greater amounts of dust, to which the operator is subjected. Various methods (eg sprayfans, on-board scrubbers and jet fans) are used in various configurations and combinations to ventilate the headings. These arrangements generally result in a complex air flow pattern, which complicates achieving an optimum balance between diluting methane and minimising dust capture. In order to cost effectively investigate and propose solutions to this problem for the South African coal mining industry, the Division of Mining Technology has embarked on an extensive work program to evaluate various ventilation methods presently in use. Four currently generic ventilation patterns in various heading scenarios have been simulated using the Computational Fluid Dynamics (CFD) computer program. Evaluating these outputs against a predetermined set of criteria allows the best system for a particular situation to be chosen. The program also facilitates fine-tuning of an adopted system without incurring the cost and inconvenience of doing such tests in situ. This process not only provides solutions at significantly reduced costs, but also yields deeper insights into the factors affecting heading ventilation than hitherto possible.

Jan 1, 1995

By Thomas MJ

The Cannington silver-lead-zinc deposit is located at latitude 21¦ 52' 9" South, longitude 140¦ 55' 10"" East, on the south-eastern margin of the Proterozoic Mount Isa Block (Figure 1), 135 kilometres south-east of Cloncurry. Access is via a graded shire road for 80 kilometres south from the small pastoral community of McKinlay.REGIONALThe deposit is hosted by the Proterozoic Soldiers Cap Group within the Mount Isa Block Eastern Succession. South of the Cloncurry Beardsmore et al (1988) have grouped part of the Eastern Succession stratigraphy intothe Fullarton River and Soldiers Cap groups (1760-1740 million years) which together make up the Maronan Super Group. This is an apparently conformable sequence 10 kilometres thick and consists of metamorphosed sediments and volcanics with intrusive amphibolite bodies.The Maronan Super Group has experienced a complex history of deformation with up to six events having been recognized. The stratigraphy trends broadly north-south and is predominantly characterized by tight, upright isoclinal fold structures.

Jan 1, 1993

Slope stability is a critical safety and production issue for open cut mines. The æslope stability radarÆ has been developed to remotely scan a rock slope to continuously measure the movement of the face. The system can detect and alert movements of a rough wall with sub-millimetre precision, and with reliability and resolution. The advantage of the slope stability radar over other monitoring techniques is that it provides full area coverage without the need for mounted reflectors or equipment on the wall. In addition, the radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. The measurement technique is tolerant of vibrations and overcomes the need for a highly stable footing required by traditional surveying systems, making it easy to move from one location to another. The system is self-powered and designed for minimal maintenance. Radar displacement images, co-registered with digital photography images, are transferred from the radar site in the pit to the mine office via a radio telemetry link. Custom-written software provides mine managers and geotechnical engineers with a complete picture of slope movements over defined time intervals. The time-history of the movement of any selected points or regions on the slope can also be displayed. Also provided is the ability to set movement thresholds that will trigger alarms at the radar site or mine office. The system has been used at numerous coal and metalliferous mines in Australia, and has provided real-time monitoring of slope stability during active mining operations. More than 20 rock wall and spoil failures have been captured by the system, and on every occasion adequate warning was provided to mine operators. The high level of movement precision and broad area coverage of the rock face provides a better understanding of the geodynamics, which leads to extra warning time. This technology enables a radical change in the management of risks in open cut mining operations.

Jan 1, 2003