Search Documents

By Marshall GA, Dickerson AW

The efficient operation of large haul trucks in large open pit mines requires an economic trade off between the haul route quality, the haul truck payloads and the level of haul truck reliability. This paper describes an investigation into the relation- ship between haul route surface quality and the level of structural reliability of a haul truck main frame. An instrumentation system for unattended recording of data on a haul truck operating normally in a mine and com- puter based analytical procedures were developed and used to identify which road segments contribute significantly to fatigue cracking at various sections of a haul truck main frame. INTRODUCTION In many open pit mines there is exten- sive use of large haul trucks to move over- burden and minerals. In most open pit hard rock mines, both the overburden and mineral ore are moved by large rear dump type haul trucks. Similar haul trucks are also widely used for coal overburden and mine site coal haulage operations in New South Wales, South Australia and Western Australia. Large bottom

Jan 1, 1982

By R C. Morris

Secondary microplaty haematite in its variety of styles and generations is the defining component of the high-grade banded iron-formation (BIF)-hosted iron ores of the world that are dominated by martite (M; - haematite pseudomorphs after magnetite). The term microplaty haematite (mplH) was introduced during the CSIRO-AMIRA 1976-1994 iron ore program, and was used to differentiate the then main export martite-microplaty haematite (M-mpl H) ore types of Tom Price-Whaleback and Paraburdoo (Paleoproterozoic), from the newly exploited, more prolific supergene martite-goethite (M-G) ores (Mesozoic-Paleocene) of the Hamersley Province that are now the major Hamersley iron ore exports.Morris (1980, 1985) suggested that the most important genetic factor that distinguishes the two main ore types was regional metamorphism of Paleoproterozoic M-G ores at temperatures normally related to diagenesis (ca 80 - 100°C). As temperatures increased, mplH grew in goethite both spontaneously as well as by nucleating on martite and other pre-existing haematite. Because the conversion of goethite to haematite involves a ~27 per cent reduction in volume, the crystals probably grew within microvoids of their own creation, with iron transfer through water resulting from the process itself, a local hydrothermal process requiring no introduced hypogene fluids.Barley et al (1999) and Taylor et al (2001) concluded instead that oxidation of introduced siderite in hydrothermally metasomatised BIF ‘protore’ resulted in mplH + ankerite by reaction with heated meteoric fl uids. This postulated ‘protore’, still preserved locally at Mt Tom Price, was described during the CSIRO-AMIRA program as local post-ore BIF metasomatic residuals. These new hypogene-meteoric concepts for M-mpl H genesis have formed the basis for a range of varying local and international models that currently dominate the literature of iron ore.No valid petrographic data supporting the hypogene-supergene modelling was found but petrographic images of goethite-related mplH growth in a range of different environments are shown.

Jul 11, 2011

By S K. Michelic, M Schickbichler, A Kharicha, E Karimi-Sibaki

The requirements for the controllability of metallurgical processes are increasingly becoming the focus of both industry and research. Advances in this field of research not only impact the stability of processes but often also influence the quality of the final product. One important way to examine processes in-depth, and thus show potential for improvement, is to describe them using physicsdriven models. In metallurgy, thermodynamic and kinetic descriptions of interactions between individual components of a system are often used to describe and analyse important metallurgical phenomena across the entire process. However, for the creation of physics-based models, boundary conditions and process variables must be implemented to enable a description that is as realistic as possible. The collection and generalisation of boundary conditions and process variables is, therefore, an important step towards functional models. The focus of this study is the determination of mass transfer coefficients between all components in a steel/slag/refractory system. For this purpose, experimental and theoretical methods are applied. Laboratory scale experiments are carried out in an induction furnace, and the mass transfer coefficients of the defined steel/slag/refractory system are calculated from changes in the chemical composition of the various components. Additionally, a calculation of the mass transfer coefficients based on dimensionless quantities is carried out. By comparing the values of the mass transfer coefficients determined theoretically and those determined experimentally in the trials, the suitability of the calculation is examined. The collection of mass transfer coefficients provides essential findings for future kinetic descriptions of inclusion modification based on the effective equilibrium reaction zone (EERZ) approach.

Aug 21, 2024

By M R. Davidson, M P. Schwarz

A model for column bioleaching is investigated to identify and understand aspects of bacteria in bioleaching applications, which have implications in heap bioleaching operations. The model is used to simulate scenarios that would otherwise be time consuming to perform experimentally. This study uses a model of bacterial transport and attachment/detachment to ore particles, with a bioleaching model for the depletion of a copper-sulfide, also accounting for liquid and gas flow and gas/liquid oxygen mass transfer. The model includes aspects such as oxygen and ferrous ion consumption, coupled with leaching of a copper-sulfide via the shrinking core model. The model is used to investigate how the rate of leaching is affected by the bacterial concentration in the columns, by the bacterial regeneration of the leaching oxidant ferric ions. The model is also used to assess the impact of oxygen limitation and inoculation method on the copper leaching. Some comparison of the model with experimental data will be shown.

Jan 1, 2004

Research cruises dedicated to seafloor hydrothermal activity along the Kermadec arc first began with the Sonne-135 expedition in 1998. This was followed by the worldÆs first systematic survey for venting along an arc during the 1999 NZAPLUME I expedition. Since then, cruises dedicated to mapping plumes along the Kermadec arc include NZAPLUME II (2002), NZAPLUME III (2004) and ROVARK (2007). In addition, the manned submersible cruises SWEEP Vents (2004) and NZASRoF (2005) utilised the Shinaki 6500 and Pisces V, respectively, to sample in detail select hydrothermalsystems for mineralised samples, rocks and vent fluids. The ROVARK (2007) cruise was the first to deploy an autonomous underwater vehicle (ABE) along the arc which surveyed Brothers volcano at a far greater resolution than had been done previously by ships on the sea surface. While these expeditions have largely been led by GNS Science, together with its collaborators from National Oceanic and Atmospheric Administration, Pacific Marine Environmental Laboratory (NOAA/PMEL), significant contributions have been made by other groups from various nations, exemplifying the global interest in seafloor hydrothermal activity associated with intraoceanic arcs. This is an ASTRACT only. A full-length paper was not prepared for this presentation.

Jan 1, 2008

This paper presents a review of computer techniques for the automatic contouring of geological and geophysical data with output as interactive display on graph plotters or graphics terminals and passive display on automatic drafting tables. The advantages of the method of fitting a triangulated surface to randomly distributed data using an advancing front algorithm are described, as well as the technique for determining interpolated values for the production of contour line segments and a contour smoothing algorithm. This contouring method is employed by the Geological Survey of Queensland and is implemented as an interactive system. An alternative method ideally suited to randomly distributed data involves the use of piecewise parametric cubic splines. This method which is ideal for sharp variations in magnitude and areal extent typical of geophysical anomalies is discussed. The mathematics of surface interpolation using non-parametric splines and an explicit piecewise surface fitting technique are discussed. Curve tracing techniques which are suitable for automatic contouring are also presented and the inherent advantages of interactive contouring using on-line plotters and graphics terminals for previewing of displays are described.

Jan 1, 1977

By T Baumgartl, T Huynh, K Tungpalan, E Wightman, M Edraki, M Tayebi-Khorami, L Huang, S Palaniandy, E Manlapig

With the increasing rate of tailing production worldwide there is a growing concern about the hazards of tailings storage facilities (TSF). Past and current mining, processing and waste disposal strategies that focus on the extraction of the valuable minerals, and an economic assessment only, are no longer suitable. Social implications and environmental legacies must be included for effective evaluation. This is possible by using an integrated assessment framework to evaluate more alternatives, including the production of additional saleable and benign streams, alternative tailings treatment and disposal as well as options for reuse, recycling and preprocessing of existing tailings. Tailings are not viewed as a final waste product but as part of the resource. From the sustainability perspective the models developed in integrated research programs will contribute to more effective methods for assessing different scenarios and potential processes and lead to better environmental management, increased production of benign tailings and improved efficiency of water and energy use and thus more responsible resource stewardship of the ore resource.This paper presents preliminary results from a multiyear research program on integrated tailings management at the Sustainable Minerals Institute (SMI), The University of Queensland, called ‘Designer Tailings’. The project involves the gathering of experimental and observational information on tailings biogeochemical processes to design and modify the range of activities within mineral processing plants, upstream characterisation ore and gangue, and downstream tailings management for desired tailings properties and outcomes. This information will assist the development of new total integrated value chain CITATION:Edraki, M, Huynh, T, Baumgartl, T, Huang, L, Andrusiewicz, M, Tungpalan, K, Tayebi-Khorami, M, Wightman, E, Palaniandy, S, Manlapig, E, Evans, C, Farrokhpay, S, Bradshaw, D and Vink, S, 2014. Designer tailings – an integrated model for tailings management, in Proceedings Life-of-Mine 2014 , pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By BLAKE DAWSON WALDRON

I must acknowledge my strategic adviser, Mr Lance Grimstone, who contributed to the development of this paper, and collated the text and figures.

Jan 1, 1994

Performance trials followed the commissioning of three large mine fans at Mount Isa in 1965. Actual performance characteristics were determined. These were in good agreement with predicted performance. Piezometer rings for volume flow and pressure measurement were calibrated, and the performance of some aerodynamic components of the installation was studied.Test equipment, preparation, and conditions are described.

Jan 1, 1967

By G Senanayake, J Andreazza

The general experience in gold cyanidation research activities and plant practice is that high oxygen and cyanide concentrations improve gold leaching kinetics which in turn reduce residence time and increase throughput. This paper shows how the improved pre-oxidation method for the pyrrhotite rich gold ore of Bounty Gold Mine has increased gold recoveries at lower reagent consumption rates. The installation of a pipe reactor, in conjunction with a Multi Mix Systems oxygen injector, has lowered the amount of oxygen required to achieve a dissolved oxygen level target of 20 mg/L. The improvement of the pre-oxidation stage and lead nitrate solution addition has led to a reduction in the free cyanide concentration required for leaching, resulting in a decrease in cyanide consumption rate by 36 per cent to achieve a one to two per cent improvement in the gold recovery.

Jan 1, 2002

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium.One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives. Controversy can always be achieved by producing a best of list; it can be guaranteed that everyone will disagree with at least one of the nominations. On this occasion, the best contributions by individuals or groups in a number of areas of mine fill technology, over the last 25 years, will be the basis for the nominal awards. The controversy can be increased by posing a number of questions that, hopefully, some of the authors will address during their presentations. I imagine the social functions will be busy enough, but the questions may just add to the cut and thrust of the debate.

Jan 1, 1998

By Hinkley JT, Smitham JB, Nicol SK

Historical investigations of mineral flotation have highlighted the many factors which affect flotation. Some of these are related to the mineral, its degree of liberation (however defined), solution chemistry and flotation reagents. The complexity of the interactions between these factors often leads to uncertainty over whether the final grade/recovery results obtained in either laboratory or pilot scale tests are in fact the maximum recovery at a specific grade. The reason for this is that there has not previously been a general technique for establishing the floatability of an ore. This study describes the further development of the 'tree' flotation technique for minerals other than coal, and in particular its application to iron ores. Oxides have been chosen as a system of intermediate complexity between the simple coal system and sulphide minerals to illustrate the principles and develop the concepts. The 'tree' flotation procedure consists of the progressive flotation to completion of successive froth products, followed by reflotation to remove entrained material. It therefore represents an 'equilibrium' approach to floatability rather than a kinetic approach. By ordering the various products and tails in order of increasing grade, a cumulative curve of grade and recovery can be constructed against which an isolated batch or plant result on the same ore can be compared. In this investigation, a Jaspilitic iron ore was tested at various grind sizes to determine the 'best' flotation grade-recovery that could be obtained with a given set of reagent conditions. The separation characteristics of a process are best measured on a system which contains particles which behave as 'middlings' with respect to the process in question. For this reason a natural ore was chosen in preference to model systems in order to relate more readily to plant situations.

Jan 1, 1993

Completion of a project requires two separate money-focused activities, namely economic evaluation of the cash flows underlying the project (before financing) and if the economics look promising, how it can be financed. Economic evaluation might be best led by a person with a technical-operating background, whereas financing might be best led by an accountant. Both should be presented in simple language with easy to understand models. Economic evaluation has a sad and bad history because it evolved from the fringes of accounting. Anyone can become a self-appointed practitioner. Some still take pride in mathematical complexity without realising that they distance themselves from the decision-makers and alienate other team members. Today there is no evaluation modelling consistency across the mining industry and this reflects poorly on our discipline. It is not tolerated amongst our peers in engineering and accounting. In 2009 æbest practiceÆ economic evaluation modelling is well defined. It is:easy to follow;tailored to its purpose;transparent;discipline, rigour and consistency;recording of all source data; and hencequick to audit. Mantra: If you cannot readily understand my model you do not have a problem, I do! The task of the economic model is to make the range of business cases underlying the decision easy to understand. Intellectual power is used to simplify the decision to its key issues and risks and to present the full range of possible business outcomes in readily understood terms. Project team members, management and the board must be able to make their decisions with æeyes wide openÆ. A steering committee should be established to develop a set of standards and practices that could be adopted for economic modelling within the industry. The industry needs to purge itself of the undisciplined economic evaluation modelling that now characterises the discipline.

Jan 1, 2009

By C B. Valentin

It is acknowledged that the analysis of iron ores using X-ray fluorescence (XRF) for major and minor elements is best carried out on fusion discs. This method of sample preparation eliminates mineral and particle size effects which can lead to biased results when using pressed powder pellets. However, the fusion disc method is costly as it requires a high capital investment in platinumware, requires experienced operators and uses expensive fluxes. Also, the dilution effect complicates the analysis of trace elements. For many applications, such as exploration and mining control, the method of XRF analysis of iron ores by pressed powder pellet probably provides data of adequate quality. Kumba Iron Ore, an iron ore producer in South Africa, recognises this and carries out most analyses of iron ore by pressed powder pellet and uses the automated fusion method mainly for certification of in-house calibration standards and quality control (QC) samples that are used for validation of pressed powder pellet method purposes. Automated fusion is also used for analysing the composite export shipping samples. All the other exploration, production, despatching and plant operation samples are done by the pressed powder pellet method. Automation of sample preparation procedures should improve the quality of data for pressed powder pellets. To compare the precision of the three methods of sample preparation and XRF analysis, 20 aliquots of a QC standard were prepared and analysed by each procedure/preparation method. The results and statistical data on the most important elements, Fe, K2O and P, are as shown later in Table 2.Clearly the precision is best for the auto prepared fusion discs, as expected, and worst for the manually prepared pressed powder pellets. However, the data generated from the auto prepared pressed powder pellets compare remarkably well against those from the auto prepared fusion discs.

Jan 1, 2007

The general principles of technical due diligence best practice that are involved in assessing a mineral property in the early stages of its development are described and a bibliography of relevant papers is attached. The issues specific to the evaluation of gold deposits are highlighted. The Australasian Institute of Mining and Metallurgy's (The AusIMM) initiatives in this area, dealing with the proper public reporting of Reserve/Resource information (JORC Code) and property assessment/valuation (VALMIN Code), will be used as a framework against which the illegal tampering with drilling samples to artificially boost their gold content (salting) from the Busang gold deposit (Kalimantan, Indonesia), owned by Bre-X Minerals Limited (Calgary, Canada), will be reviewed. While the Busang saga was based upon fraud, through salting the samples, the general lessons to learn from such a scam are worth documenting. In Australia, most of those working in the mineral industry belong to long established professional institutes and consultant associations (eg The AusIMM or Mineral Industry Consultants Association [MICA]) that require their members to work within their technical limits and to comply with best practice guidelines, or risk being judged and found wanting by their peers in the context of strong Ethics Codes. There is also a strong interface between such representative professional bodies and the corporate and financial market regulators (ASC/ASX), which closes the monitoring loop. Canada has only now seen the wisdom of having this type of early warning system in place. Fraud and deliberate deception will be always possible, but deception on the enormous scale that occurred at Busang is most unlikely with proper surveillance systems in place and the use of accredited technical professionals. There should have been more hard data available about so big and rich a deposit owned by a C$6Bn company.

Jan 1, 1997

By N Winkelmann

Underground coal heating is a significant hazard in some coal mines. The broad principles of how underground coal heatings occur is reasonably known, however the technique for locating the heatings in often inaccessible goaf has been proved to be difficult. Since 2002, CSIRO, with the support of the Australian Coal Association Research Program (ACARP) has been undertaking investigations to apply and develop innovative surface-based radon technique for locating the underground heatings in Australia. This paper presents the progress of the investigation.

Jan 1, 2005

Jan 1, 2004

By G A. Partington

Recent research has highlighted the potential of a relatively new style of gold mineralisation related to granite intrusion. New discoveries in Alaska, Central Europe and Asia and Eastern Australia with total resources of 1600 t Au offer attractive targets for regional exploration in areas which may have been overlooked in the past. A spatial information system was developed to target granite-gold systems in eastern Australia and the West coast of New Zealand, using well constrained geological and exploration models derived from current research. Target areas were recognised in Queensland, New South Wales, Victoria, Tasmania and on the West Coast of the South Island of New Zealand that have similar spatial data relationships to known granite gold mineralisation elsewhere in the world. The second phase of the modelling better constrained the regional scale target areas by including more detailed geological, geochemical and geophysical data in the GIS to develop prospect-scale targets and to allow the acquisition of tenements over these areas. A geological review of each target area was carried out in the field to put the GIS models into context. The fieldwork has highlighted the potential for this style of mineralisation in New Zealand and will increase investment in mineral exploration and development in New Zealand in the near future.

Jan 1, 2005

By E R. Ramanaidou, M A. Wells

Asian steel mills are demanding iron ore with specific chemical, mineralogical, metallurgical and environmental properties to warrant that the ore is of the greatest quality. As a result, a toolkit of analytical techniques becomes important. Hyperspectral analyses of iron ore cores and chips using a HyLogging™ system are now routinely undertaken by BHP Billiton Iron Ore in Western Australia for banded iron formation-hosted iron ores and channel iron deposits to better characterise their iron ores. Objective information can now be expanded by adding new sensors. The current HyLogging™ system provides point analysis reflectance spectra and a red–green–blue high-resolution image, while recent developments, such as hyperspectral imaging using the Corescan system, now provide full spectral image and surface topography. The addition of Raman spectroscopy provides the ability to detect and quantify quartz and magnetite (or maghemite) and cross validate hyperspectral information on hematite and goethite and aluminium substitution in the iron oxides. Micro-X-ray fluorescence mapping also adds chemical information appropriate for cross validation with the aforementioned methods. This paper demonstrates the value of combining these techniques for an optimum characterisation of iron ore.CITATION:Ramanaidou, E R and Wells, M A, 2015. A new toolkit for iron ore characterisation, in Proceedings Iron Ore 2015, pp 587–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Noller B. N, McGill R. A

The Alligator Rivers Region has been the scene of one of Australia's most intensive environmental monitoring efforts since the current generation of uranium mining was mooted in the 1970s. Prior to mining, the local environment and the nature of potential impacts were not well known. The initial monitoring programs therefore included large baseline characterisation and research components. After some 15 years, water, soil and sediment monitoring programs have been reduced to a fraction of their early size, as the mining and natural systems became better known and characterised, and the actual nature of the environmental impacts were established. Modem techniques allow much more rapid and thorough identification of chemical species and elements of concern, allowing much more focused monitoring programs to be designed. In the 1980s data collection was emphasised at the expense of interpretation, and monitoring programs were maintained at much higher levels than were in fact required. It is now clear that investigations are important and should be distinguished from monitoring programs, and that the timely interpretation of investigations and implementation of recommendations can greatly reduce the effort and expense that can be involved in a monitoring program. Monitoring programs based on a sound understanding of potential environmental impact may then be efficient and cost-effective, yet provide sufficient information to assess the environmental impact of mining, guide further environmental protection measures when problems are detected, and demonstrate compliance with regulatory requirements.

Jan 1, 1994