Search Documents

By Lawson F

Chrome chemicals are commercially produced by the alkali roasting of chromite ores with sodium carbonate. Results of tests conducted in a laboratory furnace indicated that the sodium carbonate reacted rapidly with part of the gangue material to form a metastable intermediate that later reacted further with the chromite. For the conditions used, the recovery of water-soluble sodium chromate was able to be described empirically as yield % = a tn with a = 0.24 T - 241.3; n = 3.90 - 3.12 × 10-3 T and t is the reaction time in hours.The major rate limiting step in the overall reaction sequence appears to be the rate at which oxygen can get to the reaction sites across the liquid film coating the solid reactants.Sodium sulfate alone was found to be an unsatisfactory source of alkali for reaction with chromite. However when limestone also was added in quantities sufficient to allow the reaction CaCO3 + Na2SO4 + H20 ? Ca SO4 + 2NaOH + CO2 to take place, the results obtained were comparable to those found when sodium car-bonate was used.For chromite particles in the size range -124 + 105 µm, the use of stoichiometric excess of sodium carbonate did not appear to increase the yield or the reaction rate significantly. However, with smaller sized particles, - 53 µm, increased yields of water-soluble chromate were obtained when roasted with more than the theoretical quantity of sodium carbonate.

Jan 1, 1984

By D M R Stone

Failings di,posal presents many challenges at metal mines in Peru where the extreme relief yields very little useable land area. These challenges are amplified by other hazards such as the high seismic environment, high rainfall, and frequent debris torrents down the steep hillsides. As a result many mining operations have resorted to in-river disposal of mill tailings. This paper presents a case history of one underground metal mine located in the high Andes mountains of Peru where in-river disposal of tailings has been used for some 30 years. The paper outlines a comprehensive engineering study that was aimed at increasing the utilisation of tailings disposal underground. The scope of this study included modifications to the grinding and flotation circuits to produce a high sulphide and low sulphide tailings for underground and surface disposal respectively: mapping and cataloguing of abandoned stopes for hackfilling: modifications to the existing backfill system to improve icliahility and throughput, and a preliminary evaluation of alternatives Such as silicated and paste fills.

Jan 1, 1998

By J Heyes, T Cooper, M Stimpfl, R Staines, J P. Pearce

Acid and Metalliferous Drainage (AMD) is one of the key risks facing the mining industry worldwide. If not properly managed and/or not identified in a timely manner, AMD has the potential to decrease environmental values for generations to come. Ore extraction generates vast volumes of mineral waste (waste rock and tailings) which are stored in perpetuity at the mine site. Some of these materials are not inert and when in contact with air and water can react, generating poor quality water and compromising operational and closure environmental objectives. Understanding the geochemical behaviour of waste rock and tailings is therefore key to identifying risks and opportunities which support effective mineral waste management strategies across the mining value chain and progress toward an environmentally sustainable future that minimises closure liabilities. To ensure AMD risk is recognised and managed uniformly across its portfolio, BHP developed a Global AMD Management Standard for implementation across all operations, including closed sites. The AMD Management Standard provides a management framework to support the consistent, simple and sustainable global management of AMD risks. This ensures mines are planned and operated to be environmentally smart and modern, geochemical risk management is not an afterthought but a key driver, and environmental sustainability is actively pursued to reduce closure liabilities. The AMD Management Framework, on which the Standard is based, was adapted from industry leading practice guidance, ensuring it applies to multiple regions. The framework also comprises sequential requirements throughout the mining life-cycle. It is an iterative framework with an adaptive management approach that is designed to incorporate new data, information and management opportunities into AMD risk assessments and mine plan revisions.

Jul 1, 2021

By M Freeman

In a visionary move, the Planning Commission and the Ministry for Planning in Western Australia decided to invite three extractive industry quarry operators, local government councils and State Government departments (Minerals and Energy, Environmental Protection, South West Development Commission) to contribute jointly to study the impacts of blasting on areas surrounding basalt quarries in the Bunbury region of WA. The results of the study will help establish suitable zones in which land uses will be controlled under a proposed Greater Bunbury Region Scheme and in local planning schemes, to minimise conflicting land uses. This paper discusses the blasting program conducted to characterise and model the vibration behaviour of the rock under the effects of pilot-scale and full production blasting, and highlights some of the benefits achievable when a thorough blasting impact program and assessment is conducted at the planning stages of land-use establishment.

Jan 1, 2001

By D P. Blair

The theme of this conference is blasting productivity. This article only considers the technology aspect of this theme, and in particular, the collection and analysis of experimental data. In many cases, field trials are set up to collect data on variables such as fragmentation and vibration with the aim of comparing different explosive products and/or blast designs. An important aspect of such trials is the collection of sufficient data to draw sound conclusions. In this regard, there is no doubt that the scatter in real data is the root cause of all problems of obtaining misleading results due to an insufficient number of trials. This article shows that the typical one-off trial has a high probability of producing misleading information, which could be considered to be worse than having no information at all. Assuming that sufficient data has been collected, this article also highlights the methods that can be used to make the most of that data. These methods include the application of appropriate statistics that are dependent on the nature of the scatter in the data, and the use of some of the more recent filtering and spectral approaches that can be used to reduce the noise in measured blast signals and increase the resolution of their spectral characteristics.

Nov 8, 2011

Two characteristics of the modern mining industry are that there is a skill shortage and that young professional people rise rapidly into highly responsible supervisory positions. With this responsibility comes the burden of identifying and managing health and safety risks. Without the benefit of a comprehensive health and safety training program, these young professionals may be putting both themselves and those under their supervision at risk. The Moura Mine explosions and the asbestos health disaster should not be just artifacts of history, but highly valued lessons that impress the need for comprehensive health and safety risk management strategies on young professionals. From the perspective of the former secretary of the Committee to implement the findings of the Moura (Disaster) Inquiry and as the former coordinator of the Coal Workers Health Scheme, key issues in occupational health and safety management systems are explored.

Jan 1, 2005

By D Blair, L Fergusson, G Barros

"The purpose of this paper is to present the findings of a waste rock remediation program conducted at a gold mine in New South Wales (NSW) over a six-year period. The treatment of waste rock dumps included the longitudinal results of one-off applications using: ViroMine Technology, including the application of a chemical reagent called Terra B, which is a benign, clay-like substance derived from processed bauxite and other sources lime and biosolids (added for nutrient value) clay capping and topsoil compared treatment outcomes from these three approaches to a control.Parameters measured in the program included leachate pH, total actual acidity (TAA) and chromium reducible sulfur (CRS), Al, Cd, Cu, Fe, Mn, Ni, Pb, Zn, and tree height and vegetative cover density with data collected at regular intervals over a six-year monitoring period. Findings over the life of the study indicated, for example, that leachate pH in the control area was 4.5 in year 1 falling to 4.0 by year 6; pH in the lime and capping treated waste rock was initially raised to about 5.5 after treatment but fell to 5.0 within 24 months and remained a low 4.7 by year 6; pH in the Terra B waste rock was 6.8 in year 1 immediately after treatment, and actually increased to 7.3 by year 6 with no further treatment. This finding is of relevance because it effectively profiles the acidity curves of waste rock control, lime, and capping applications, and shows that they decline over time, despite an initial æpH shockÆ to the solids as measured by TAA and CRS in the case of lime. Similar treatment curves were observed for heavy metal leachates. Tree height and vegetative cover density indicated that with increasing acidity in the waste rock dump, the lime and capping options did not allow healthy revegetation, but in the Terra B treated areas tree growth and density were comparable to background, undisturbed forest levels.is needed with respect to tailings management, based on a novel integrated research framework.CITATION:Fergusson, L, Blair, D and Barros, G, 2012. Sustainable waste rock remediation and revegetation - A real-world longitudinal study comparing ViroMine technology to standard applications and doing nothing, in Proceedings Life-of-Mine 2012 , pp 249-258 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By P Holt, M Allen

On the first of July, 2012, the Australian GovernmentÆs Clean Energy Act commenced. From this point, a price of $23/t of CO2-e will apply to facilities that trip the liability threshold. This first part of this paper concentrates on the mechanics of the Clean Energy Future legislation and how it will be applied to the mining and mineral processing industry.The second part of this paper contains analysis of the data presented for typical mine operations. Methodologies for constructing a carbon strategy are also presented. This will entail determining what the objectives of the carbon strategy are, and defining what the strategic priorities for a business should be. An action plan to address the risks identified from the Clean Energy Act is also developed as part of the strategy.Details such as the advantages and disadvantages of opting into the carbon price scheme for liquid fuels are shown. Other considerations such as the ability to acquire permits through the carbon farming initiative or through overseas clean development mechanism projects are explained.CITATION:Allen, M and Holt, P, 2012. Implications of the carbon price and developing a carbon strategy, in Proceedings International Mine Management 2012, pp 105-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By J Jackson, M F. Young

"Ore is the economic portion of a mineral deposit that can be extracted economically. Hence an ore type is a classification of the ore based on one or more dominant characteristics in order to enable communication between unit operations and/or technical disciplines.In project evaluation, ore types are often defined early based on geological observations by geologists and initial metallurgical testing is based around this classification even though a number of processing options can be under evaluation. However, the geological drivers of performance for each of these processes can be very different and the ore type classification for one process may not be relevant for another. In operations an ore type, as either defined in the project evaluation phase or those that evolve with additional knowledge, is unlikely to provide the knowledge required across all the unit operations. The ore type has a meaning to someone but does not necessarily for all unit operations across the value chain.Geometallurgical or orebody knowledge has evolved through the consideration of multiple processes within the value chain, the improved understanding of variability of process performance within ore types and the effect on the complexity of the mineral extraction processes. Furthermore orebody knowledge has been moving from personal based knowledge and understanding to a more process oriented approach where measurement and spatial and process performance modelling is playing a greater role. Advances in mine planning and scheduling allow for both detailed analysis of the block model and the expected extraction processing attributes across various time scales. This capability of analysing and describing the complexity still requires to be communicated to the various unit operations, which may be beyond the traditional classification of an ore type.The limitations of an ore type and potential alternatives to enable the relevant information to be communicated to the relevant groups are outlined through a number of case examples across the value chain.CITATION:Jackson, J and Young, M F, 2016. Ore Type – Everything to Someone but Nothing to Anyone, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 267–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M Sandy, A Vakili, J Albrecht

Although rock strength anisotropy is a well-known phenomenon in rock mechanics, its impact on geotechnical design is often ignored. No widely accepted guideline currently exists for its characterisation. Anisotropy can significantly control the failure mechanism and progression of damage into the rock mass, particularly in high-stress conditions. As such, it can play a key role in the stability of underground excavations and subsequent geotechnical design.This paper introduces the concept of anisotropy at both intact and rock mass scales. It then presents guidelines for measuring anisotropy and assigning rock mass strength properties. An improved unified constitutive model (IUCM), which can account for more complex failure mechanisms, is then briefly described. This IUCM is used to better understand the typical responses of anisotropic rocks to underground mining and to develop an improved damage classification scheme for these conditions.The application of conventional design methods in anisotropic conditions is shown to lead to significant errors. Two case histories are then presented, illustrating how the proposed methodology can improve the reliability and accuracy of the geotechnical analysis when compared with conventional design methods.CITATION:Vakili, A, Albrecht, J and Sandy, M, 2014. Rock strength anisotropy and its importance in underground geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 167–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J Rutter, J du Plessis, er, M Scott, D Alex

It is generally acknowledged that bulk ore sorting is an attractive prospect for the mining industry. However, uncertainties relating to the operational performance of sensor technologies, the grade heterogeneity present in analysed material and the physical separation performance of the coupled system complicate the evaluation and deployment of bulk ore sorting strategies at operations. To assist in the quantification of these uncertainties, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and Anglo American have implemented a systematic methodology to evaluate the deployment of sensor technologies for bulk ore sorting. This methodology was implemented at a bulk ore sorting demonstration plant using penetrative prompt gamma neutron activation analysis (PGNAA) and surface x-ray fluorescence (XRF) measurements of base metals, as a proxy for precious metals, at Mogalakwena PGE Mine. The methodology comprises of three phases. The initial phase involves the preliminary investigation of sensor technologies and analysis to reduce identified risks prior to commissioning of the bulk ore sorting plant. The second phase executes a series of experiments to prove the sensing technologies in the operational environment and provide confidence the sensors can drive separation. The final phase demonstrates the production scale bulk ore sorting performance of the plant and validates its performance by campaign of the sorted products at the processing plant. Throughout the operational deployment and evaluation of bulk ore sorting at Mogalakwena, several key lessons were learned. These learnings relate to the calibration requirements of the sensor technologies, the application of surface vs penetrative sensor techniques and the preservation of grade heterogeneity delivered to the sensors. This paper presents the methodology used, and lessons learned, in the operational deployment and evaluation of PGNAA and XRF sensors for bulk ore sorting at Mogalakwena PGE Mine.

Nov 10, 2020

By J P. van Dijk, M Munro

Discrete vein modelling presents an innovative geology driven 3D modelling method for quantification of vein hosted mineral deposits, with far reaching potential for critical mineral supply and low impact resource extraction. By integrating key geological drivers with advanced discrete fracture network modelling, the DMX protocol (launched in 2019) converges to a more realistic representation of complex vein systems in three-dimensional space. The approach insights greater geologic reasoning in distributing mineral grades where vein boundaries are already defined. This presents a viable alternative to existing modelling and estimation methods and has important implications for mineral resource estimation and reporting. Further implications are discussed, where the enhanced understanding of complex orebody characteristics can potentially be used in optimising mining and mineral processing, supporting more sustainable and efficient mining practices.

Sep 1, 2024

By A S. Lund

Optimisation of the underground mining production process benefits from informed decision making during the process of explosive rock fragmentation. Selection of the most appropriate bulk explosive products for underground production blasting is an area of endeavour that offers significant economic upside if correctly and thoroughly undertaken. The explosive selection process is facilitated by a clear understanding of:the physical and detonic properties of the alternative explosive options available; the response of different rock masses to these different explosive options; and the importance of maintaining a clear focus on desirable blast outcomes in order to enhance value creation aspects of the mining production process. The level of understanding of these issues is raised through the application of measurement and modelling technology, quantifying the effects of blast design (and implementation) on process outcomes. Homestake Darlot and DynoConsult applied a range of dynamic blast measurement and outcome modelling techniques in order to explore the relationship between rock properties, explosive properties and mining process efficiencies. A campaign of vibration and explosive Velocity of Detonation (VoD) measurement produced feed data for use in vibration and fragmentation modelling during the extraction of one of the major stoping blocks at Darlot Gold Mine. The paper describes the use of these tools and discusses the understanding gained concerning the limitations and capabilities of, and the reconciliation between, a selection of analysis and modelling approaches.

Jan 1, 2001

By M S. Fenzel

Increased environmental regulations and pressures have created changing and new demands for tailings management strategies in a variety of mining applications. Critical among these items is the disposal of tailings as the pursuit of increased yields and lower costs have driven the application of different process technologies. With a number of technologies having a niche application focus, the belt filter press has been utilised for decades as a cost-effective and versatile option for dewatering different types of mineral tailings and other waste process streams. One of the critical advantages of the belt filter press is the technology’s ability to adapt and work in numerous plant designs, operating conditions and applications. As permitting and disposal options have become more stringent, plant designers, operators and equipment suppliers must develop comprehensive and site-specific economic, design and process evaluation techniques to ensure proper equipment selection and system design for belt filter presses or any other dewatering technologies. This paper will explore these techniques in relation to belt filter presses (with reference to other technologies) in a variety of different applications, along with other considerations to ensure a successful tailings dewatering system and disposal design. Summaries of equipment performance characteristics, operating and maintenance strategies and optimisation techniques will also be addressed in conjunction with the belt filter press’s adaptability to different plant designs and the resulting tailings characteristics.CITATION:Fenzel, M S, 2015. Analysis and adaptability of belt filter presses and other technologies for tailings dewatering over a range of mineral processes, plant designs, conditions, regions and operating philosophies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

The general types of industrial behaviour of liberated valuable sulfide minerals in the 0 - 10 ¦m size fraction are described and tests to explore on site at a concentrator the general nature of any deficient behaviour are discussed. In addition, the general types of behaviour of the gangue minerals in this size fraction are also described in terms of their mechanisms for recovery. These behaviours are also discussed in terms of the type of grinding device and grinding environment in which they were produced and the target grinding product size. Major recent improvements in the industrial capabilities of grinding devices are discussed.Present difficulties in characterisation of particles in the 0 - 10 ¦m range are described and desirable improvements for the future are outlined. Further, desirable improvements for industrial processing of valuable minerals in this size range are discussed along with some remedial actions.

Jan 1, 2005

By A Grace, C Sennersten, T Taylor, A Davie, R Lyu, D Pentecost, C A. Lindley, J Craig, L De Macedo Camargo

Many underground mine void spaces are not suitable for human entry due to unprotected roofs, instability or having an unknown safety state (eg if they are many decades old). Investigations of these voids may nevertheless be important for general mine safety, for example to detect propagating collapses or water accumulation, prevent accidental intrusion by new developments or drilling to reassess old spaces for re-mining. Robots are an ideal technology for investigating these spaces, especially flying, rotary-wing robots that can access and map vertical structures and spaces while avoiding rocks, water and mud that have accumulated on void floors. To operate in underground mines, we are developing customised unmanned aerial vehicles (UAVs) as well as interactive 3D virtual models of the vehicles and their underground environments for controlling vehicle operation and visualising incrementally gathered survey data. Using a game/simulation engine to provide an interactive interface for UAV operation makes it possible to orchestrate external spatial information and video feeds with in-game cameras for optimal visualisation that is not limited to the position, orientation or field of view of cameras mounted on the UAV. First and third-person points of view with respect to the UAV are provided, together with 2D and 3D gaze tracking to provide effective interfaces for geology and mine engineering experts without the need for specialist UAV piloting skills. Ongoing work is addressing the provision of greater levels of autonomy for these vehicles to support mapping well beyond the line of sight of operators and geological characterisation of rock surfaces using sensors mounted on them, including miniature X-ray fluorescence and Raman spectrometers. Gathered data is fed into more general 3D models of the mine, block models and orebody so that the UAVs function as elements of a mobile perceptual system for intelligent mining.CITATION:Sennersten, C, Lindley, C A, Davie, A, Lyu, R, Grace, A, Evans, B, Pentecost, D, Taylor, T, De Macedo Camargo, L, Craig, J, Salomao, G N, Hellicar, A, Biggins, D, Timms, G, Coombe, M, Shahriar, M S, Smith, G and Rahman, A, 2015. Unmanned aerial robots for remotely operated and autonomous surveying in inaccessible underground mine voids, in Proceedings Third International Future Mining Conference, pp 101–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By P Lukic

The definition of the working sections that will be used in a mine is usually initially made in the field by the geologist supervising the drilling program. These initial definitions are often made on the basis of rules of thumb such as æcoal less than 30 cm thick cannot be mined separatelyÆ; æpartings more than 30 cm thick will be mined separatelyÆ; and æif a coal seam is less than 50 cm thick and the parting above or below is thicker than the coal, the coal will be wastedÆ. These decisions are also often made based on the requirement for a minimum sample mass for analysis, and the desire to collect data at the minimum resolution to conserve the exploration budget.In many cases the geological models based on this data are produced at a resolution that is inadequate to allow the mining engineer to produce a mine plan that will maximise project value. This problem is generally unrecognised.Where data is collected to a higher level of resolution the subsequent processes employed in the production of geological models and mine plans often discards the inherent value that is hidden in this data. Again this problem is generally unrecognised.This paper highlights this problem and then presents a methodology that ensures that the optimal working section is selected and compares the outcomes of applying this methodology versus adherence to the usual rules of thumb.

Sep 26, 2011

By J Robinson, L D’Uva

"The Gold Fields group and Gekko Systems have successfully worked together on multiple projects, including at the St Ives, Agnew and Granny Smith operations in Western Australia, and the Damang operations in Ghana, with gravity recovery design, technology installation and optimisation the key driver on each occasion.In 2014, Gold Fields Australia identified an opportunity to challenge the historical thinking at Granny Smith and reassessed the benefit of upfront gravity gold recovery. The historical approach had been to employ gravity on the tailings stream of the carbon-in-pulp (CIP) circuit, recovering sulfide minerals into a concentrate from spiral concentrators for further liberation of gold via a regrind circuit.Gekko was engaged to assess the implementation of a gravity circuit within the grinding area, and to perform a comprehensive gravity recoverable gold test program. Test data was fed into the AMIRA P420 BCC Gravity Model to confirm the gravity recovery potential of the ore, and for process design basis generation. Height, space and capital limitations proved to be a design challenge. However, collaborative learnings throughout the project ensured the design and operation of a reliable and economic gravity gold circuit. Ultimately, the Granny Smith gravity circuit was a success, satisfying all the project objectives and yielding consistent, measurable benefits. On average, the gravity circuit recovers 33 per cent of total gold, resulting in an increase to overall gold recovery by 0.7 per cent.This paper highlights the key project drivers for Gold Fields, and the development of the Granny Smith free gold gravity circuit. It details application of test work and modelling, and the challenges and learnings encountered during the design, installation and commissioning stages. This paper seeks to demonstrate that continuous improvement in a long standing operation can be beneficial to overall circuit flexibility and increased ounce production.Citation:D'Uva, L, Robinson, J and Bell, T, 2016. Defying Gravity - Brownfield Continuous Improvement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 135–144 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S F. Rogers, K Doumis, J H. Graaf, B J. Barsanti

Advances in technology now allow geotechnical practitioners to better describe the properties and variability of a rock mass through advances in surface and underground mapping, borehole technology and geophysical imaging. Yet the way in which practitioners use this data is not being realised to its full potential and the quality and quantity of data that is collected is often superior to the conventional design approaches that are typically adopted. A discrete fracture network (DFN) approach provides the ideal basis for using this data to generate geologically-realistic rock mass models based on parameters derived from field data, which more effectively capture the variability and rock mass behaviour. However, until recently, the DFN approach has mainly been applied to cave mining and small-scale models associated with synthetic rock mass modelling or groundwater flow modelling for the nuclear waste and oil and gas industries.Ground support design for blocky rock masses in Australia is often dealt with in a rather traditional manner, adopting either an observational empirical approach through rock mass classification systems or conventional wedge stability analysis techniques. Using these methods requires several generalised assumptions about the rock mass fabric and excavation geometry. As such, the support system is often designed for a worst-case scenario based on a predetermined risk tolerance that the mine is willing to accept and a design block size that is generally determined by the proposed excavation dimension.A study by Doumis (2014) used conventional wedge stability analysis and the probabilistic key block analysis software JBlock (Esterhuizen, 1996) to estimate potential block sizes and support requirements. A DFN approach has also been adopted at Callie underground mine using FracMan™ software (Golder Associates, 2014). The methodology of the DFN wedge analysis will be compared with the key block analysis work undertaken by Doumis.CITATION:Graaf, J H, Barsanti, B J, Doumis, K and Rogers, S F, 2014. Towards the implementation of discrete fracture network modelling as a geotechnical design tool – case study of callie underground mine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 399–408 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By P Clark

This paper discusses the challenges, solutions and lessons learnt as tunnelling work continues on the Melbourne Main Sewer Replacement (MMSR) project.The MMSR project is a $220 million dollar project for the Melbourne Water Corporation. It involves the construction of approximately 4.2 km of new sewer from the southern fringe of the CBD through the inner metropolitan suburbs of Port Melbourne and South Melbourne.Of the 4.2 km of sewer currently in construction approximately 2.2 km will be constructed using a 2.95 m diameter Lovat EPB tunnel boring machine (TBM) with approximately 1.9 km of small diameter (300 to 600 mm) reticulation sewers constructed using trenchless techniques.These sewers are being constructed in a dense urban environment, which means that the tunnels and shafts are often in close proximity to buildings and structures. The underground constructionof the sewer is further complicated by the variable geology of the ancient Yarra River delta which includes weathered basalts, the infamous Coode island silt formation and fine loose sands.Some of the key challenges and lessons learnt so far during construction include:· steering and alignment control of the TBM through very soft silt with little residual strength,· development and refinement of a monitoring and alarm system for leaving the machine dormant on a day works only project,· control and measurement of tunnel lining defl ection during ring build and grouting,· prediction and monitoring of surface settlements during tunnel excavation,· improved understanding of the geology and hydrogeology at this previously unchartered area of Melbourne,· consolidation settlement due to dewatering at shafts required careful construction controls, and· ground support and excavation in close proximity to the existing 110 year old sewer which requiredvery detailed risk control measures.

Mar 8, 2011