Search Documents

By Ovchinnikov YN, Novikov VS, Spirin NA, Babushkin NM, Mysik AF, Shcherbatskii VB, Kukarkin AS

Laboratory investigations were carried out to determine the resistance coefficient of the flow through beds irrigated with wetting and non-wetting liquids. A formula was obtained which may be used to evaluate the resistance of the irrigated packing. Quantitative investigations were also carried out on operating furnaces at Magnitogorsk. Continuous measurements of the lower pressure drops were made under different furnace conditions. Pressures were measured in the tuyere space and the bosh region. A significant transient behaviour of the pressure drop was observed in the irrigated zone as a function of the accumulation of the liquid phase in the bosh region as smelting progressed. Additionally, transient processes were also investigated in the upper furnace zones. The basic cause of the transient behaviour was shown to be the irregularity of burden descent caused by the casting cycle. It was shown that the rate of burden descent between consecutive casts reflects fairly accurately the accumulation and drainage of the liquid products as a result of which heat transfer, reduction and aerodynamic processes assume transient character. In practically all cases of casting a decrease in blast pressure and that over the furnace height of 0.2 kg/cm2 was observed. The analyses of radial gas composition at the stock line showed that compositional variations connected with the casting cycle are most pronounced in the central and peripheral regions, whilst in the intermediate regions the conditions are relatively stable. Calculations show that as casting progresses there is a decrease in the gas flow rate at the periphery and an increase in the centre of the furnace. The transient nature of the aerodynamic processes in packings revealed the existence of an appreciable reserve capacity. Elimination of transience was tested on the furnace at Magnitogorsk and improved operating and economical furnace parameters obtained.

Jan 1, 1975

By C Mason, A Littleboy

This paper presents the results of a large scale survey of The Australasian Institute for Mining and Metallurgy (AusIMM) membership. This survey aimed to understand and define the key issues and drivers that AusIMM members perceived would shape the development of the Australian minerals industry over the next 20 - 30 years. Nine hundred and fifty-nine participants rated the importance of 11 issues and six drivers (generated from interviews with AusIMM members), and 236 of these participants also provided qualitative descriptions of the future. Issues were defined as problems or opportunities for the minerals industry that may be controlled or influenced by the industry, while drivers were defined as those factors that will influence the direction of the industry that are not within the control of the industry. The quantitative data revealed that the top four issues, in order of their perceived importance to the Australian minerals industry, were: investment in exploration, workforce, health and safety, and innovation. The top three drivers in order of their perceived importance, were: economics of mining, global context and Australian society. While the top four issues were largely consistent across professional groups examined, metallurgy and mineral processing professionals rated water inputs and energy inputs significantly higher than the other professional groups. For the list of drivers, there was strong agreement regarding their ranked order of importance across the professional groups examined. Within the qualitative data, however, a single issue (technology) and a single driver (economics of mining) dominated participantsÆ descriptions of the future. These findings provide important input into a broader program of scenario development for the Australian minerals industry being undertaken by CSIRO and its partners. The results of this study demonstrate the importance of using a mixed methodology in generating these inputs to understand more fully how important stakeholders view the future and the factors that will shape it. The results of this study are also discussed with respect to the role that CSIRO may play in facilitating the exploration of uncertainty around the future of the Australian minerals industry.

Jan 1, 2009

By P Breuer, D J. Robinson, A McFarlane, L L. Kuhar

Increasing global demand for commodity metals and capital and the greater operating costs of mining and metal production present significant challenges for the metals mining industry. Current conventional technologies may not be feasible for processing deposits of declining grade, challenging mineralogy or those that occur at increasingly greater depths. To overcome these issues, the development of a step-change technology such as in situ recovery (ISR), which reduces mining and avoids milling costs, may be vital in ensuring future economic metal production. ISR has been used extensively to treat porous soft rock deposits such as the water-soluble salts, sylvite and halite. Although ISR has typically been used for mining conventionally uneconomic uranium ores, it has also been used less frequently for the treatment of other restricted permeability hard rock deposits, such as those containing copper and gold. The reason for the limited uptake of the technology for hard rock mineralisations is primarily due to low natural rock porosity and permeability and hence poor response to available lixiviant. However, additional challenges include solution containment, management of groundwater and regulatory, ecological and societal requirements and expectations. CSIRO has focused on understanding the challenges of hard rock ISR and identifying global capabilities that can contribute to developing the essential enabling technical areas required to realise ISR. Specific focus areas include geochemistry and advanced resource characterisation; drilling and controlled rock-breaking technologies; solution chemistry and environmentally benign lixiviant systems; lixiviant delivery systems and ‘subsurface mixing’; subsurface hydrology and reactive transport mechanisms and models; downstream processing options; legal, social and environmental aspects; and techno-economic modelling. This paper will discuss ISR challenges including industry feedback focused on addressing this issue, gaps preventing ISR from being applied in practice, capabilities to overcome these gaps and the development of a collaborative approach to making hard rock ISR a reality.CITATION:Kuhar, L L, Breuer, P, Robinson, D J and McFarlane, A, 2015. Making hard rock in situ recovery a reality, in Proceedings Third International Future Mining Conference, pp 189–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By A Woodley, G Keir

The mining industry faces concurrent pressures of reducing water use, energy consumption and greenhouse gas (GHG) emissions in coming years. However, the interactions between water and energy use, as well as GHG emissions have largely been neglected in modelling studies to date. In addition, investigations tend to focus on the unit operation scale, with little consideration of whole-of-site or regional scale effects.This paper presents an application of a hierarchical systems model (HSM) developed to represent water, energy and GHG emissions fluxes at scales ranging from the unit operation, to the site level, to the regional level. The model allows for the linkages between water use, energy use and GHG emissions to be examined in a flexible and intuitive way, so that mine sites can predict energy and emissions impacts of water use reduction schemes and vice versa. This paper examines whether this approach can also be applied to the regional scale with multiple mine sites.The model is used to conduct a case study of several coal mines in the Bowen Basin, Australia, to compare the utility of centralised and decentralised mine water treatment schemes. The case study takes into account geographical factors (such as water pumping distances and elevations), economic factors (such as capital and operating cost curves for desalination treatment plants) and regional factors (such as regionally varying climates and associated variance in mine water volumes and quality).The case study results indicate that treatment of saline mine water incurs a trade-off between water and energy use in all cases. However, significant cost differences between centralised and decentralised schemes can be observed in a simple economic analysis. Further research will examine the possibility for deriving model up-scaling algorithms to reduce computational requirements.CITATION:Keir, G and Woodley, A, 2013. Regional trade-offs between mine water and energy use - a water treatment case study, in Proceedings Water in Mining 2013 , pp 21-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

The purpose of this paper is to list by tabulation and flow sheet, the operating equipment and installations in use at Rosebery, and to refer to particular items which may be of interest for purposes of comparison, or because they possess some unusual feature. The general perspective has been taken from the viewpoint of operating and maintenance experience.The sequence begins with ore breaking and transport and proceeds through milling operations. The paper is in two sections, first, mechanical equipment, second, electrical equipment. A brief outline of a scheme for using gravel wash for stope filling, which is in course of installation, has also been given.

Jan 1, 1949

By N Madani, S Abulkhair, N Morales

Conventional geostatistical algorithms cannot reproduce bivariate complexities such as inequality constraint, nonlinearity and heteroscedasticity. Poor reproduction of these features may decrease the accuracy and reliability of mine planning results. For example, it is not unusual to have an inequality constraint between primary and disturbing elements in a metalliferous deposit. Implementation of traditional methodologies for such complex data sets can lead to the incorrect reproduction of a bivariate relationship, which will affect the validity of NPV results. In this paper, an iron data set containing iron and silica grades with an inequality constraint between variables is introduced as a case study. This study proposes an algorithm based on a hierarchical sequential Gaussian cosimulation integrated with inverse transform sampling. The proposed methodology considers the linear inequation between two variables in the hierarchical cosimulation process to reproduce an inequality constraint. As a comparison, conventional sequential Gaussian cosimulation is also applied to the same data set to demonstrate the difference in bivariate relationships from both models. Unlike the proposed algorithm, the conventional cosimulation cannot reproduce an inequality constraint and slightly overestimates silica grades. The modelled realisations are then used to assess the uncertainty of a plan and generate a stochastic strategy that adapts the destination of the blocks depending on the scenario. Two-stage stochastic long-term production scheduling takes extraction decisions using average information (ie e-type model) and ore/waste destinations based on geostatistical realisations. As a result, the proposed strategy is closer to the upper bound, highest possible NPV for each realisation, than to the lower bound, deterministic strategy that does not manage the risk of sending extracted material to wrong destinations. Furthermore, Comparing production schedules resulting from proposed and conventional geostatistical methodologies shows the importance of inequality constraint reproduction and more accurate long-term mine planning.

Nov 8, 2021

By C Fricke, R Wood, P Velletri

"In a climate characterised by an ever increasing focus on cost reduction and maximising the utilisation of existing assets and infrastructure, understanding the uncertainty associated with alternative investment and operational choices becomes paramount to minimising the risk of making an ineffective decision. To assist in this process, TSG Consulting has developed an analytic framework to capture the underlying complexity of a mineral supply chain, and then quantify the impact of the uncertainty associated with the key drivers of business productivity. The technical basis of this approach follows three distinct steps: analyse the current system and identify the major factors that drive value build detailed models that can measure the response of the system to potential changes in the factors identified quantify the sensitivity of financial and capacity forecasts to these factors.Each of the above steps draws on a different area from the field of applied analytics, namely: data analytics dynamic modelling and designed experimentation meta-modelling and optimisation.Following the three-step approach described above ensures a rigorous modelling and analysis process is executed to support strategic mine planning decisions. The approach is equally applicable to the analysis of fully integrated system supply chains (pit-to-port), the evaluation of incremental capital investments to targeted areas of a supply chain, or when considering revisions to the operating philosophy of a system in the short term. The basis of each of the three analytic steps is explored in detail in this paper. The result is the definition of a structured mechanism for a business to actively manage risk and drive productivity as a component of the strategic mine planning process.CITATION:Fricke, C, Velletri, P and Wood, R, 2014. Enhancing risk management in strategic mine planning through uncertainty analysis, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By Kelly D, Moore C

The Golden Mile, which has been mined continuously for the past 100 years by both underground and more recently open pit methods, occupies an area of 1.2 km by 4 km adjacent to the city of Kalgoorlie Boulder in Western Australia (Figure 1). Large-scale open pit mining at the Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operations is currently extracting 7.8 million tonnes of oxide and sulphide ore for a total production of 522 000 oz per annum. The effectiveness of grade estimation techniques at KCGM has been examined with reference to existing 10 m bench sample data from all operating areas within the Eastern Lode System of the Main and North pits. The aim of the study was to recommend practical parameters for grade control estimation. The review included comprehensive variography and comparison of nonparametric estimation methods (Joumel, 1983) such as indicator kriging and probability kriging with ordinary kriging, leading to the development of improved grade control parameters and procedures for both daily quality control and short term mine planning. This paper reviews the geological, statistical, geostatistical, mining and modelling features studied in order to present KCGM's Mining Department with recommendations for improving grade control.

Jan 1, 1994

By R Neivandt, Kane, M O&apos, D Browne

Newmont Australia is the operator of the Mt Leyshon mine near Charters Towers, Queensland. Mt Leyshon is an open cut gold mine, which processed on average 5.0 Mt of ore and produced up to 250 000 ounces of gold per year. Mining was completed in early-2001, followed by treatment of low-grade ore stockpiles for a further 12 months. Approximately 250 ha of waste rock dumps have been rehabilitated. Rehabilitation of two of the three tailings storage facilities (TSF) has been completed and the third is in progress. A field performance monitoring system that includes an automated meteorological station, large-scale lysimeters (measurement of net percolation), and in situ moisture content sensors (measurement of moisture storage changes in the cover material) were installed to monitoring performance of the cover systems placed on the waste storage facilities. This paper focuses on the installation and calibration of the in situ moisture monitoring system. The moisture monitoring system provides automated detailed in situ volumetric water content data above and within the large-scale lysimeters. A portable unit that provides spatial in situ moisture content measurements at additional locations on the cover system is also utilised. The paper will focus on installation and calibration of the in situ water content monitoring instrument in the waste rock, coarse cover material, and fine textured cover materials of the tailings facility and waste rock dump cover systems.

Jan 1, 2003

By P Mikula, B Darlington, J Graham, P Young

In underground mines experiencing dynamic events, there is an ever-present challenge to design and maintain a capable ground support system. One key component of ground support systems is surface support, which serves the essential roles of retaining failed rock and transferring forces generated by surface displacement to rock bolts or other support elements. Observations underground show that in many instances, standard mesh panels alone do not provide sufficient dynamic support to retain substantial bulking failures imposing displacement onto mesh, and in such cases Mesh straps and W-straps may be employed. Determining the performance of surface support elements proves to be difficult, with a multitude of variables at play in the underground environment. Quite comprehensive work has been completed on laboratory testing of surface support systems; however, very little work has been conducted on in situ dynamic testing of Mesh straps and W-straps. In 2019 in Western Area’s Flying Fox Mine, in situ dynamic testing was conducted on a series of Mesh straps and W-straps using Sandvik’s in situ Dynamic Test Rig (DTR). The testing regime applied impact energies from 5.1 to 15.3 kJ to Mesh straps and W-straps. The performance of the straps that did not fail was a maximum absorbed energy of 9.3 kJ and 14.2 kJ for the Mesh straps and W-straps respectively. The testing successfully demonstrated the ability of Sandvik’s DTR to test not only rock bolts, but also surface support elements, creating new testing and research possibilities. The testing also provided important design guidance data that is not practicable to obtain using laboratory dynamic testing facilities.

Nov 29, 2022

Following the Moura No 2 Wardens Court of Inquiry and subsequent changes to the Queensland Mining Legislation there is a requirement in Queensland coal mines for: a person with the recognised competencies to be appointed at each underground coal mine to the position Ventilation Officer; and the person is directly responsible for the implementation of the mine ventilation system and for the establishment of effective standards of ventilation for the mine. The Regulations require that an underground mine must have principal hazard management plans that provide for at the least the following: emergency response, gas management, methane drainage, mine ventilation, spontaneous combustion, and strata control. Other than strata control all the plans require the ventilation officer to have roles and responsibilities to develop, control, monitor and undertake actions in relation to these plans.There are also another 34 Regulations that either directly or indirectly requires the Ventilation Officer to take actions.The purpose of this paper is to outline the information that the regulators look for in sealing plans and the actions the regulators will take if the sealing does not go to plan (TARPs being exceeded).

Jan 1, 2005

By W Malone, J Garrett

FLSmidth (FLS) has spent the last 15 years, working with customers and engineering houses to deliver innovative improvements in crusher safety, coupled with the latest, maintenance friendly, crusher design. The key focus being to prevent service personnel from working underneath the crusher during maintenance and obviate the need for personnel to be exposed to suspended loads when performing tasks such as, main shaft installation, for example. Improvements include: full top-service capability to ensure the safest and fastest way to disassemble the crusher for maintenance purposes, which also removes the requirement for a service cart; a selfaligning main shaft which ensures remote assembly is now possible, keeping service personnel well out of harm’s way; And rotable shells, or the ability to perform relines off-station, allows for quick shell ‘swap-over’ without the downtime associated with removing, refitting and curing time associated with epoxy backing. The high flow spider improves large material entry into the crusher, reducing blockages and downtime and therefore maintains crusher capacity. Each size of crusher in the range comes with an option to increase the standard feed opening to a larger one if desired to compensate for ‘blocky’ or ‘elongated’ feed material, a common problem for Pilbara hematite iron ores. Power capability has also been increased with a maximum of 1500 kW, to match the higher throughput capacities being achieved. This due to uprated eccentric speeds and larger discharge annulus. Increased eccentric throws and mantle diameters are also now a reality, when compared to more traditional designed gyratory crushers. To keep up with the improved design features of the Mk V, digitalisation has also been upgraded to maximise performance capabilities to ensure that the most efficient reduction and throughput capacities are achieved, whilst utilising the higher powers now available as standard. Condition monitoring ensures that the crusher is at its optimum operating capability by monitoring and adjusting the crusher settings via feedback from additional sensors, ie main shaft spin, temperature and vibration. Camera monitoring capabilities are available as is an advanced oil contamination monitoring system. As a result of the above design improvements, it will be shown that the Mk V range offers benefits such as: enhanced safety features, increased availability, faster maintenance turnarounds, higher power utilisation, equivalent product size at higher throughput capacities and with Remote operation capabilities. All of which result in a gyratory crusher with higher levels of safety and a lower per tonne operating cost.

Sep 18, 2023

By J G Bastias

It is sometimes necessary to resort to extremes in order to call attention to something that is pertinent to safety in mining. When some of the experts in occupational safety talk about this topic, they usually refer to a 'regulation' established by the Romans which stated that, due to the health hazards, usually death, no Romans but only slaves should work in mining. Since the time of the Roman Empire, a lot of ground has been covered in the field of mine safety. Nowadays, it can be said that occupational safety is being seriously addressed, with the result that the number of mining accidents has reduced dramatically, fatalities in this industry are less frequent, and the rate of accidents compared with other activities, such as construction or fanning, is low. This achievement has been possible initially through government legislation and by procedures established by the mining companies themselves. However, the dilemma for government is whether to regulate and if so, how much. It is pleasing to observe that most companies are establishing working procedures which conform with new government legislation, placing strong emphasis on the duty of care for mine employees. There will always be some regulatory aspects of legislation, and perhaps the best example of this is in the use of mine hoists where there are no international or Australian standards, and the regulations applied are of an empirical nature that err on the side of safety.

Jan 1, 1994

By S Pradhan, A Kuras, R Mahajan

This paper describes the design of the precast concrete segmental lining for the 13.1 m internal diameter and 450 mm thick, 2.4 km long mainline tunnels for the Waterview Connection project in Auckland for the New Zealand Transport Agency.The design and detailing of this segmental lining presented some noteworthy challenges, including an alignment that has sections of low cover in soft ground. Key points of interest are that this precast segmental lining is the largest to ever include steel fibres as the primary method of reinforcement and the lining includes cams on circumferential joints to control ring deformation.The paper describes some of the key design decisions that were made in a collaborative manner with the construction team, tunnel boring machine manufacturer, segment manufacturer and the designers.CITATION:Mahajan, R, Kuras, A and Pradhan, S, 2014. Design of segmental lining for Waterview Project, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 289–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By K Rozlapa, P Waters, H Middlemis

A major challenge for closure planning at mining operations below the water table is evaporation from final void pit lakes and concentration of salts, which can impact on downstream groundwater (and surface water) flows and quality. Where such impacts are deemed unacceptable, the closure approach that is often adopted is to infill the final voids with waste rock to above the pre-mining water table to prevent the development of a pit lake and subsequent evaporative losses. BHP Billiton Iron OreÆs Marillana Creek (Yandi) mining operations face these issues. The orebody is a channel iron deposit that forms the major aquifer in the region, which will be completely mined as a series of elongated open pits over tens of kilometres. The major constraint on mine closure planning was the stripping ratio of less than one, which means that there is insufficient waste rock to infill all areas to the pre-mining water table. Hydrogeological investigations and groundwater modelling indicated that standard mine closure approaches would result in pit void lakes becoming saline sinks unless the residual void geometry was optimised to minimise evaporation and maximise throughflow. The solution developed is a cost-effective long-term mine plan that meets all mine closure objectives, and involved:the selective infilling of all pits, largely using run-of-mine waste dumping with limited re-handling; the diversion of the major part of up-catchment creek flows around the mining operations to allow mining of the resource under Marillana Creek crossings, which in turn restricted overall aquifer recharge and reduced the elevation of the long-term water table; the diversion of some minor creek tributary flows into specific locations within the mine path to induce hydraulic gradients to maintain groundwater throughflow and water quality; and close integration of mine plan optimisation (mining and waste dumping schedules) with groundwater modelling scenarios to achieve acceptable environmental outcomes. This approach is designed to result in no reduction in downstream surface water flows or quality, maintenance of adequate downstream groundwater throughflow to support groundwater dependent ecosystems, and no reduction in the beneficial use status of the downstream groundwater resource.

Jan 1, 2006

By C Ausa, Nyunt Htay, A, L Deiparine

The main tectonic elements in Myanmar are a late Mesozoic and Cenozoic magmatic arc system in the west, repeated in northern Myanmar by more than 300 km of dextral movement on the Sagaing Fault, and the back-arc continental region affected by early and late Mesozoic orogenies, in the east. Historically most lode gold production has been from latest Cretaceous high-grade mesothermal veins and derived placers in the Wuntho and Tagaung-Myitkyina segments of the magmatic arc. Placer deposits in the Ayerwaddy River north of Myitkyina are currently worked by more than 100-bucket dredges. South of Wuntho, the magmatic arc and Pegu Yoma fold belt host epithermal gold with associated As, Sb and Zn in mid-Tertiary marine sediments. MyanmarÆs most productive lode gold deposit, the Kyaukpahto mine, lies within a north-trending district east of the magmatic arc and north of Mandalay. Here mineralisation and associated jasperoidal silica occur in Eocene sandstones and Permian and Triassic carbonates. Possibly this district continues southeastwards, across the Sagaing Fault, as sediment-hosted Sb Au and locally skarn Au mineralisation within a 1100 km long fold-thrust belt. Also present in the back-arc region are sandstone-hosted Au Cu in a Palaeozoic slate belt, and gold and stratabound gold-base metal mineralisation in the medial metamorphic belt. While untested targets remain in the magmatic arc, particularly for high sulphidation Au, the best potential is clearly within the back-arc slate and fold-thrust belts in the western part of the Shan Plateau and in northeastern-most Myanmar.

Jan 1, 1999

By C Mark

Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are a particular hazard because they typically occur without warning. During the past two years, three US coal miners were killed in two coal bursts, following a six-year period during which there were zero burst fatalities.This paper puts the US experience in the context of worldwide research into coal bursts. It focuses on two major longwall mining coalfields that have struggled with bursts for decades. The Utah experience displays many of the ‘classic’ burst characteristics, including deep cover, strong roof and floor rock, and a direct association between bursts and mining activity. In Colorado, the longwalls of the North Fork Valley (NFV) also work at great depth, but their roof and floor strengths are moderate, and most bursts have occurred during entry development or in headgates, bleeders or other outbye locations. The NFV bursts also are more likely to be associated with geologic structures and large magnitude seismic events. The paper closes with a brief discussion of how US longwalls have managed the burst risk.CITATION:Mark, C, 2014. Coal bursts in the deep longwall mines of the United States, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

A laboratory investigation was carried out to obtain data on the explosive character- istics of selected coals mined in New South Wales. Seven coal seams were sampled and the volatile matter content of the coals tested varied between 28 and 37 percent. A mod- ified Hartmann apparatus with a volume of 1250 ml was used in the investigation. Dust clou' generation was produced by an air blast delivered radially through a mushroom type valve and the ignition source was a-continuous A.C. spark produced by a 20 000 V, 50 mA transformer. The coal dust parameters invest- igated were the maximum pressure developed, the average and maximum rates of pressure rise at dust concentrations between 200 and 1500 3 g/m.

Jan 1, 1981

By L C. P J Fonteneau, B Godel, E R. Ramanaidou

The Hamersley Province in Western Australia hosts large iron ore deposits. Each deposit displays various iron ore types that were defined on their metallurgical properties, especially in terms of porosity and mineralogy. Conventional porosity and mineralogy information on iron ore types are provided on 2D thin sections using automated image analysis with scanning electron microscopy (SEM)-based techniques combined with chemical analyses. However these techniques cannot accurately quantify the 3D porosity. High-resolution X-ray computed tomography (HRXCT) is a non-destructive technique providing a 3D image of the sample with a resolution close to 0.5 - 0.7 ¦m for samples size of up to few centimetres in length. 3D image analysis using customised algorithms now provide accurate quantitative porosity and mineralogy of iron ore types.CITATION:Fonteneau, L C P J, Godel, B and Ramanaidou, E R, 2013. Application of high-resolution x-ray computed tomography to iron ore characterisation, in Proceedings Iron Ore 2013 , pp 243-250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The face of project evaluation is changing continuously, making it ever more critical to get a clear understanding upfront of the objectives, decision-making processes and criteria of the project proponents. Requirements are usually significantly different for emerging æjuniorsÆ compared with long established major mining houses and companies in developing countries compared with western companies. Requirements are also different for different types of evaluations, such as due diligence studies compared with feasibility studies of æownedÆ projects and there are often key misunderstandings around the use of the term æbankableÆ. Further, it has become increasingly important with increasingly remote and lower quality resources to understand risk relativities such as infrastructure compared with the core processing facilities. This has also driven the need for more trade-off studies to determine the best balance between critical issues, such as optimisation of the interface between mine and processing plant, capital versus operating cost and automation versus labour. In every project evaluation, it is also critical to consider emerging trends and changing requirements and standards such as sustainability and community interface. Finally, the inescapable drive to reduce time to market has driven changes such as increased use of more standardised designs and innovative approaches to the transition from project development to execution. This paper begins with a brief review of the different objectives and risks of each project development stage to establish a framework for subsequent discussion of the different requirements of different types of companies in different locations, different types of evaluations and different types of projects and project components. This is followed by a review of changing requirements and standards and some innovative developments in sustainability and community interface are presented. Finally, the paper outlines a number of developments in the area of operational readiness planning that focus on minimising the time to achieve maximum return on investment.

Jan 1, 2009