Search Documents

By F. V. Lenel, G. S. Ansell, M. J. Salkind

An experiment is described in which the growth of interparticle necks in an array of loose spherical silver powder at temperatures near 300°C was determined by measuring changes in the electrical resistance of the array. The activation energy for neck growth of contacts was derived by abruptly changing temperature and noting the change in the rate of neck growth. Since the experiments were run under an external load, the changes in activation energy with stress could he determined. The activation energy was found to decrease rapidly with increasing stress. It is concluded that the material transport in the experiments is one of plastic flow by dislocation motion. The variation of activation energy with stress is typical for cross slip of dislocations, an important material transport mechanism in the temperature range investigated. THE process in which powder compacts or aggregates of loose powder are held at an elevated temperature under an external load is called hot pressing or sintering under pressure by powder metallurgists. In this investigation the early stages of this process as applied to loose spherical silver- powder aggregates were studied. The powder particles were approximately 100µ in diameter and the temperature was near 300°C, i.e., below one half of the melting point of silver in degrees Kelvin, where volume diffusion is not expected to contribute to sintering. In the process, the contact or neck areas between powder particles grow. Since this involves plastic deformation of the particles under a constant external load (even though not under constant stress) it would be termed creep by mechanical metallurgists. On the other hand, the growth in neck area observed in compacts or loose-powder aggregates held at elevated temperature without the application of an external load is termed sintering by powder metallurgists. During sintering the major driving force is the stress due to surface tension. However, even when no load is placed on the compact or powder aggregate, an external stress, i.e., gravity, plays an important role in sintering in addition to those stresses arising from surface tension, as was shown in two previous investigations.'" It is therefore postulated that no sharp dividing line can be drawn between the phenomena of "creep" and "sintering". Different material transport mechanisms may be involved in either of these phenomena, but they will depend upon the temperature and the level of stress, but not necessarily upon the nature of the driving force: surface tension or external load. At the low temperatures of this investigation, an external stress much higher than the stress due to surface tension is necessary to obtain measurable rates of neck growth. In order to avoid misunderstanding this phenomenon will be called "creep". The rate of growth in contact area in the loose silver-powder aggregates was determined by meas-

Jan 1, 1965

By W. O. Philbrook, A. H. Jolly, T. R. Henry

IN the course of a study of slag-control methods, the authors devised a laboratory technique by which the basicity of basic open-hearth furnace slap could be estimated with sufficient accuracy to make the method of possible interest for slag-control purposes. The process consisted of measuring the slight basicity of an extract of the powdered slag in water. The procedure was presented, for the benefit of those who might care to experiment with it, in a paper submitted in the 1944 McKune Award Contest and presented at the 1944 Open-hearth Conference in Pittsburgh.1 Interest expressed at that meeting and favorable operating experience with the method at a neighboring plant, as described in a related paper by Michael Tenenbaum and C. C. Brown,2 have encouraged us to present further details of the development, technique, and pitfalls of the method and some additional data not included in our first report. At the outset it must be admitted that this method of estimation of slag basicity is not perfect; neither is any other that we know of. It is subject to somewhat greater errors than would be desirable, but compares favorably with other techniques in this respect. It has the disadvantage that it places the final determination of slag basicity in the hands of a laboratory technician rather than the furnace operator, although it can be operated in a control laboratory adjacent to the furnaces. It requires close attention to certain details, as do most laboratory procedures. On the favorable side, it eliminates the "human factor" of personal judgment inherent in estimation from pancakes or powdered samples. The procedure can be placed in practice much more rapidly and presents much less of a training problem than visual methods of estimation. The principle and operation of the method are so simple that it would not be surprising if others have experimented with the same or similar procedures, but we are not aware of any prior publication of details. Our own shop has been operating fairly successfully for several years with the aid of slag pancakes. Since the past year or two have not been favorable for the expenditure of time and energy where the need was not urgent, we have not introduced the new practice for actual slag control and hence do not have extensive operating data. In presenting this method, therefore, we make no claims as to theoretical justification nor guarantees as to practical applicability, but offer it as an empirical observation. We believe it has sufficient merit to warrant its investigation by those just instituting a slag-control program or in search of supplementary methods for judging slag basicity PRINCIPLE OF THE METHOD It is well known that when burnt lime or slaked lime is shaken up with water it

Jan 1, 1945

By J. Campbell

The negative pressure developed within a solidifying sphere of pure iron is investigated theoretically assuming an elastic-plastic model. The maximum hydrostatic tension attainable is shown to be an order of magnitude smaller than that required for the homogeneous muclealion of pores in the liquid cove, and four orders of magnilude smaller than that predicted from) a rigid shell model. It is well-known that liquids can withstand large hydrostatic tensile stresses, or negative pressures. The various experimental investigations of the tensile strengths (often called the fracture pressures) of liquids are reviewed by Dean,1 and the theoretical attempts at estimating fracture pressures are critically assessed by wakeshima.2 Using Fisher's3 quation, the fracture pressure of pure liquid iron is about -70,000 atm, which may be too large by as much as a factor of 4, but is certainly correct to within an order of magnitude.' In view of the great importance of the problem of the nucleation of shrinkage cavities in castings it is of interest to determine exactly what tensile stresses can exist in the residual liquid in a solidifying casting; it has often been assumed that, because of the very low strengths of solid metals near their melting points, no interior stresses are developed at all. Nussey4 has determined theoretically the pressure in the liquid core of a solidifying metal sphere assuming that the solidified shell does not deform (i .e., is perfectly rigid), so that because of the contraction accompanying solidification (a) (about 3 pct for most metals) the progressive deposition of solid onto the inner surface of the shell causes the remaining liquid to be expanded to make up this difference in volume. This leads to a relation between the pressure P in the liquid, the initial pressure, PO, the bulk modulus of the liquid, K, and the inner and outer radii of the solid shell, o and b, respectively:

Jan 1, 1968

By Clarence Zener

[ ] THE present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 27 to 30. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1946

By G. A. Alers, J. H. Bechtold, R. W. Armstrong

The plastic flow of .molybdenum was studied in compression at temperatures below the ductile-to-brittle transition in tension. It was found that molybdenum is ductile in compression at all temperatures down to —196°C. The yield strength continues to increase with decreased test temperature below the tensile ductile-to-brittle transition temperature range. Difficulty was encountered in correlating the experimental data obtained with existing theories of plastic flow. THE body-centered-cubic metals as a group show a rapid and very large increase in yield strength with decreasing test temperature.' It is of fundamental importance to the understanding of the mechanism of plastic flow that this general characteristic be examined carefully. Unfortunately, brittle fracture in low-temperature tensile tests prohibits the measurement of flow properties at very low temperatures. By using compression tests, fracture can be suppressed and the plastic flow of the bcc metals can be studied far below their tensile ductile-to-brittle transition temperatures. Molybdenum was chosen for this experiment and plastic-flow data were obtained down to —196°C.

Jan 1, 1959

CONTENTS PAGE World-V. R. Garfias 3 Russia-R. C. Beckstrom 6 Rumania-I. I. Gardescu 11 Germany-W. Kauenhowen 14 France, Italy and Poland-W. P. Haynes 20 Persia-Sir John Cadman 23 Iraq-E. B. Swanson 27 Burma and India-L. D. Stamp 30 Venezuela-H. Sherman 37 Trinidad-H. W. Reid 44 Colombia-O. C. Wheeler 47 Peru-O. B. Hopkins 50 Mexico-V. R. Garfias and R. V. Whetsel 51 Canada-L. C. Snider 55

Jan 1, 1933

By H. F. Beeghly

UNTIL recently the only criteria by which steels were judged were their cost and their mechanical, chemical, and physical properties. The user was concerned with such properties as corrosion resistance, tensile strength, response to thermal treatment, hardness, ductility, and, to a growing extent in recent years, with behavior at high temperature. As plans were made to build power reactors, a new set of properties became important—the nuclear characteristics, which had to be considered by the designer and engineer in building his plant. The nuclear engineer developed methods for the rare and new metals and produced them in high purity, often at great expense. The pure metals then provided the raw materials for tailor-made alloys. For more common structural metals, such as steel, the nuclear industry depended on commercially available materials. Generally, the quantities required were small and specifications were rigid. It is not surprising, therefore, that difficulty was frequently encountered in procuring structural mate-

Jan 1, 1957

By John W. Bell

In the introduction to an excellent pamphlet, John Gross' makes the following statements: Although marked progress has been made along mechanical lines, the theory and conception of underlying principles have not advanced so rapidly. This lack of advance in theory may be attributed to the unfortunate situation resulting from the controversy as to whether the Rittinger or Kick law is applicable to crushing. Many pages of the technical literature are burdened with theoretical discussions in favor of one or the other of these laws, which have tended to cloud rather than to clear the atmosphere. Realizing the situation, the Milling Committee of the American Institute of Mining and Metallurgical Engineers, through its secretary, E. A. Hersam, studied the milling industry and, because of the apparently hopeless lack of agreement in the Kick versus Rittinger dispute (5, 13, 14, 16, 18. 19. 21, 22, 23, 24, 30, 34). concluded that a foundation lor the theory of crushing was of primary importance. The numbers in the paragraph quoted refer to papers listed by Mr. Gross in his Bibliography on Crushing and Grinding.I One is obliged to infer that these papers show "hopeless lack of agreement in the Kick versus Rittinger dispute." No. 22 is a paper by Arthur 0. Gates2 and No. 23 is one by the writer.3 Employing the subject matter contained in papers Nos. 22 and 232,3 the writer will show that their authors formulated identical conclusions, based solely on experimental evidence. Exactly the same defect in the Stadler hypothesis was described in each of the two papers, although entirely different experimental methods were employed in uncovering it. Both of the authors, independently, formulated the conclusion that Rittinger's was a true hypothesis and Stadler's false. The evidence in a third paper4 will be employed to prove that Stadler's hypothesis, when examined experimentally, is worthless. Stadler's Hypothesis Worthless It is the writer's opinion that the evidence available in 1915 and the corroborating evidence in 1916 was amply sufficient to eliminate the need for any further consideration of Stadler's hypothesis. Certainly the evidence produced in 1918 dealt this hypothesis its coup de grace. It follows, therefore, that in the year 1918 there was only one credible hypothesis left—the Rittinger hypothesis. Gates' Opinion What information is available in Mr. Gates' paper?2 His conclusions are not consecutively summarized, none the less they are perfectly clear. On page 876, Gates says, and it is a very significant utterance: But my results show, among other things. that many more of Stadler's energy units are obtained per foot-pound-applied in coarse than in finc crushing. This suggests a doubt as to the correctness of his unit, since one would expect a foot-pound-applied to produce the same number of "energy units," whether the feed and resulting product were coarse or fine. When Rittinger's theory is applied, the number of mesh-tons (my unit of surface produced) is

Jan 1, 1943

By F. F. Frick, Frederick Laist

In a leaching process, having obtained the copper in solution, the choice of the precipitation method is influenced by the following factors: 1. Availability of precipitant. 2. Adaptability to the leaching process. 3. Final product desired. 4. Regeneration of leaching solutions. 5. Fouling of solutions. There are three general classes of precipitation methods: 1. The use of iron, scrap or sponge. 2. Electrolytic deposition. 3. The use of some gas or reagent by which the copper is obtained, usually in the form of an intermediate precipitate which requires further treatment. For example, the precipitation of, the copper as Cu2Cl2 from chloride solutions; with SO2 gas. The use of iron is adapted to almost any process. It has the great advantage of extreme simplicity, and the recovery of the copper and any values present in a highly concentrated, easily treatable form. The disadvantages are the cost in isolated places, the uncertainty of the scrap-iron market, and the fouling of the leaching solutions. The latter is a serious factor, when a reagent such as salt is used in them, which makes necessary their re-use. Where applicable, electrolytic deposition is very attractive. The copper is obtained in a form directly marketable, there is a regeneration of acid and no fouling of solutions. Unfortunately, chloride solutions do not lend themselves to electrolysis. An entirely satisfactory anode material has not yet been discovered, although magnetite, apart from being rather brittle, seems to answer the requirements fairly well. The use of a method of the. third class is involved in many special

Jan 1, 1915

By John B. Hastings

The occurrellce of such a large amount of gold in the Hart-eel granite, even though the surmised existence of similar areas is not new, brings freshly to mind the pegmatite type of mag-matic differentiation lately brought again to attention by occurrences at Silver Peak, Nev., described by Spurr; and in Alaska, described by both Spurr and Brooks. In both localities granitic rocks or dikes are thought to pass into metalliferous quartz-veins. An interesting association in this connection is the occurrence of diamonds in residual pegmatitic clay of Sail Juao de Chapado, Brazil, described by Derby :' (P. 142) "Bodies of pegmatite are quite common in the older rocks of Brazil, both in the diamond regions and elsewhere, occurring not only in the gneiss and granite, but in the schistose series as well. Those that have been examined are dike-like in their mode of occurrence and granitic in composition.'' (P. 143) '" The question of the eruptive or secretionary origin of pegmatites has long been a subject of discussion among geologists.... The recent studies .. seen] to have clearly established that most if not all of them are essentially eruptive masses, though possibly modified in some way by aqueous agencies. Even before becoming acquainted with the literature of the subject this view had seemed to me to be the only acceptable one as regards the typical pegmatites of Brazil." What is pegmatite ? J. F. Kemp says :2 "... veins or dikes—it is an open question which is the more correct term— are met formed of very coarsely crystalline aggregates of the same minerals that constitute granite. These are called pegmatite and in them is the home of graphic granite, the curious intergrowth of quartz and feldspar, such that a cross fracture of the blades of quartz suggests cuneiform characters.... In regard to the larger veins or dikes it seems improbable that true igneous fusion could have afforded such coarsely crystalline aggregates, and so we are forced to assume such abundance of steam and other vapors, i.e, mineralizers, as to almost, if not quite, imply solution."

Jan 1, 1909

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By L. A. Rapoport

This paper is intended as an aid in the perfornzance and interpretation of experimental studies of multi-phase flow in porous tnedia. The mathenmatical formulation of incompressible, two-phase flow phenomena in a three-dimensional porous medium is presented. The resulting equations which account for the effects of gravitational and capillary forces are used to derive general scaling laws permitting accurate representation of water-oil displacement processes by means of experimental flow models. The significance of the scaling laws is examined in the light of the physical concepts of micro-behavior of fluids in porous media. Formulations of scaling con(litions obtained by application of dimensional analysis are reviewed. The principles of application and the limitations of flow model studies are discussed. INTRODUCTION Most of the problems facing a reservoir engineer involve three-dimensional, two-phase flow systems. influenced by the effects of gravitational and capillary forces. Present computational procedures generally do not permit the evaluation of such systems without introducing greatly simplifying assumptions. The actual reservoir configuration is usually replaced by one or a combination of several "equivalent" linear systems, and the effects of capillarity and gravity are considered to be negligible. While these assumptions may in many instances be justified, there are a number of important practical problems for which the results obtained on the basis of such simplifications remain open to question. An alternate approach to the problems that are not amenable to analytical treatment consists of seeking their solution by experimental laboratory investigations. The main difficulty of such investigations lies in the fact that multiphase flow phenomena subjected to gravity and capillary forces proceed differently at different rates and in systems of different dimensions. Therefore, unless great discrimination is exercised in selecting the conditions and interpreting the results of laboratory tests, such tests may be entirely misleading in regard to field applications. The purpose of this paper is to present a theoretical background for the performance of laboratory tests that are more nearly representative of field behavior. It will be shown that simulation of field behavior can be achieved by conducting laboratory tests under conditions selected in accordance with definite scaling laws. The formulation of conditions required for the scaling of two-phase flow experiments in porous media has been presented in the literature on several occasions.12,3,4 One of these formulations advanced by Leverett1, cannot be considered applicable to most practical cases inasmuch as it does not cover generally the regime of laminar flow. An adequate treatment, based on the consideration of dimensional analysis, was presented by Engelberts and Klinkenberg.2 Their treatment, however, is concerned primarily with the scaling of linear flow systems, and hence somewhat limited in scope. Accordingly, the formulation of more general scaling laws, applicable to three-dimensional systems, appeared to be warranted. It appeared, furthermore. desirable to establish this formulation on the basis of a mathematical treatment, rather than by application of general principles of dimensional analysis, to permit more explicit

Jan 1, 1956

By C. P. Proctor, J. T. Crawford

TROUGH washers were among the earliest methods used for concentrating ores; they are referred to by Agricola about the middle of the sixteenth century as already being used while the hand- operated jigging sieve had only recently come into use. For cleaning coal the trough washer apparently was first used in France and Belgium about 1841. The early trough washers were intermittent and the refuse at least was shoveled out by hand. The invention of a continuous jig washer, by a Frenchman, Berard, in 1848, acted as a stimulus to coal washings in jigs and retarded progress in trough washing in the nineteenth century. Chapman and Mott' describe a number of trough washers developed in England and on the Continent from 1850 to 1900, such as the Bell and Ramsay, Ramsay, Bell and Green, Wunderlich, Scaife, McLellan, Lodge, Elliott, Blackett, and Murton. The later of these removed the refuse mechanically, either intermittently or continuously, but in ways that interfered with stratification.

Jan 1, 1943

By H. R. Aldrich

This paper is not a treatise on the theory and practice of magnetic surveying. It presents a diagram upon which have been plotted observations taken with the simplest form of magnetic instrument, the lowly dip needle, over a large area astride the Lake Superior syncline of northern wisconsin. The exposures of the underlying formations are not sufficiently great in number nor fortunate in distribution to have provided the fuller understanding of the geology which has been secured by the use of the magnetic observations as an auxiliary tool or accessory in the hands of the geologist. The diagram (Fig. 2) in large part speaks for itself if studied in connection with the geological map (Fig. 1) for which it is the main control. It is presented to demonstrate the extent to which the use of such methods may aid in the solution of geological problems in a covered country. The diagram is probably unique in assembling the expression of such a wide range of formations, affected by so wide a range of secondary processes, and deformed by so many different structures in terms of magnetic variation. Few geologists outside of the Lake Superior country have had any first-hand experience in the taking of magnetic observations and the interpretation of the results in terms of geological conditions; nor have the Lake Superior men gone with the methods far afield from the mere tracing of iron formations. In more recent years the oil companies have gone heavily into investments in magnetometers, balances, and dip needles in the quest of concealed structural anomalies which are the favorable loci of petroleum accumulation. But these geophysicists come back from the fields with their collections of observations facing the question of interpreting the geological meaning of their magnetic anomalies. It is considered probable therefore, and certainly it is the hope of the writer, that the appended charts, or magnographs, which show how character of the country rock and its changes, structural strike and dip and their changes, depth of burial and its variation, contact metamorphic

Jan 1, 1929

By G. Rowan, M. W. Clegg

Approximate analytical solutions for non-Darcy radial gas flow are derived for bounded and infinite reservoirs producing at either constant rate or constant pressure. These analytical solutions are compared with published results for non-Darcy flow obtained on digital and analogue computers, and the agreement is show to be very good. Some observations on the interpretation of gas well tests are made. INTRODUCTION The flow of gases in porous media is a problem that has been the subject of much study in recent years [l - 71 , and many methods have been proposed for solving the non-linear equations associated with it. The assumption that the flow satisfies Darcy's Law It has been observed, however, that the linear relationship between the flow rate and pressure gradient is only approximately valid even at low flow rates, and that as the flow rate increases the deviations from linearity also increase. It has been suggested by a number of authors that Darcy's Law should be replaced by a quadratic flow law of the form This form of equation was first suggested by Forchheimer [9] and, later, Katz and Cornell [10], and Irmay [lll, developed a similar equation. Houpeurt [12] derived this form of equation using the concept of an idealised pore system in which each channel consists of sequences of truncated cones giving rise to successive restrictive orifices along the channel. This type of representation leads to a quadratic flow law of type [4], for all fluids, but it is found that the quadratic term is only significant in the case of gas flow. The methods of Houpeurt for solving gas flow problems will be discussed further in another section of this paper. Solutions of the non-linear equation for Darcy gas flow 121 may be classified as either computer (digital and analogue), or approximate analytical ones. The former include the well-known solutions of Bruce et al. [13], and Aronofsky and Jenkins [14] , but the latter solutions, apart from the simple linearisation of equation (2) to yield a diffusion equation in p2 , are not so well-known. Amongst these approximate analytical solutions should be mentioned the work of Barenblatt [IS], who has applied the techniques of dimensional analysis to obtain similarity solution to a large class of non-linear equations; also, a number of Russian authors, including Barenblatt [16] , Kim [17] and others, who have used the method of moments for obtain-

Jan 1, 1965

By Mark N. Alling

A few years ago, gravel mining in the ancient river beds of Sierra county was the principal industry of the county. Operating drift mines were very numerous and many large hydraulic mines were in action. Eventually the State laws put an end to hydraulic mining, it being claimed that the silt carried down the streams to the valleys filled the rivers and caused winter floods, which were damaging to the surrounding farms. The ancient river deposits which could easily be found were, in the course of 40 years, worked out or practically so. The prohibition of hydraulic mining was a severe blow to the industry in general. The deposits were not developed and the gravel-mining industry practically stood still for many years. In Sierra county, nearly all the hydraulic mines were at the points where the ancient channels were exposed to view by reason of the modern stream erosion, or, in the miner's language, where the channels "enter" or "break out of" the ridges. The claims covering them also covered large areas in which were long segments of lava-capped channels, suitable for drift mines, and the points being hydraulicked were usually the controlling points of attack. Men who have followed hydraulic mining for any length of time seldom are content to work a drift mine. Knowing the great value of their deposits and feeling that they had been robbed by the State, these men have stubbornly held to their claims. The gold that is carried in these gravel channel deposits is more or less scattered throughout the depth and width of the deposit; the percentage that can be recovered by the process of drifting ranges from 50 to 75 per cent. of the total. In hydraulicking, practically all of the deposit is put through the sluices, and as the cost per cubic yard is only about 10 per cent. of the cost of drifting, the deposits, if classed as hydraulic mines, are much more valuable than if classed as drift mines; hence the old timers have held their claims (now worthless as hydraulic mines) at prices which the drift-mining industry could not stand; and such mines

Jan 1, 1915

By J. Leja, A. Pomianowski

This paper deals with equimolar solutions of xanthate and alkyl trimethyl ammonium bromide adsorption on copper, nickel and sphalerite powders. After an exposition of the experimental methods used and the results obtained, a thorough discussion leads to the conclusion that some molecular association between xanthates and CnTAB's does take place in the bulk of the solution as well as at the air/liquid interface. A spectrophotometric study of xanthate solutions alone and their mixtures with equimolar amounts of alkyl trimethyl ammonium bromide (CnTAB) has established the additivity of ultraviolet spectra (190 to 400 mµ) for potassium ethyl xanthate (KEtX) and C12TAB. No obvious effect of C12TAB addition on the decomposition rate of KEtX was observed, the half life of which was established as 29±3 days at 22°C and pH ~ 6. In mixed solutions of longer xanthate homologues (e.g. hexyl and nonyl) and equimolar CnTAB, colloidal precipitates are gradually formed which contain primarily the corresponding xanthate molecules. The kinetics of collector abstraction by copper, nickel and sphalerite powders were studied in 10-5 to 10"3 M solutions of KEtX alone and in equimolar mixtures of KEtX and CI2TAB. Presence of C12TAB caused a two to three fold increase in the amounts of xanthate (equivalent to many monolayers) abstracted by copper and nickel powders (and in their rates of abstraction) but had no effect on the abstraction of xanthate by unactivated sphalerite (equivalent to less than a monolayer). The adsorption of C12TAB itself from the mixed solutions was very low, at most one monolayer only, and was not influenced by the nature of the solid powder used. A change in the rates of abstraction, observed with copper powder, was interpreted as a completion of a multilayer coating (completely enveloping the grains of powder) following which the rate of reaction between solution and substrate becomes controlled by diffusion through this coating. Work of Buckenham and Schulmanl on molecular associations between different collectors has shown unusual synergistic effects in flotation of individual minerals using mixtures of xanthates and alkyl trimethyl ammonium bromides. The objectives of the present work were: 1) to determine whether these molecular associations between the two types of collectors (indicated by strong surface tension lowering in Buckenham and Schulman's work) take place at the air/liquid interface only or in the bulk of solution as well 2) to establish whether different solids adsorb any species from the mixture of these amphipatic molecules preferentially or as molecular complexes 3) to establish whether there are any differences in the kinetics of adsorption. Metallic copper and sphalerite powder were chosen as adsorbents since they represent two extremes since copper readily adsorbs multilayers of xanthate (and is easily floated with ethyl xanthate) while unactivated sphalerite does not appreciably adsorb xanthate but is known to be readily floated by the amine type collectors. Metallic nickel was included because the infrared spectroscopic work2 on xanthate

Jan 1, 1964

By T. E. Leontis, D. H. Feisel

MAGNESIUM alloys containing rare earth metals have received considerable attention during the past several years because of the need for light alloys having high strength and creep resistance at elevated temperatures. Although much of the work reported earlier has dealt with alloys containing Mischmetal, it has been shown in two previous papersl, V hat distinctly different effects are produced by various rare earth metals and rare earth metal mixtures on the properties of magnesium. For example, much higher strengths are obtained in magnesium alloys containing didym-ium (essentially neodymium plus praseodymium) than in alloys made with Mischmetal, which contains all the rare earth metals in the proportions in which they occur naturally in the monazite ore. Mg-rare earth metal alloys are characterized by a relatively coarse grain size, which greatly impairs castability. The addition of zirconium as a second alloying ingredient has been shown8,7 to refine the grain size, which also produces a distinct improvement in the strength properties. Certain Mg-Mischmetal-Zr and Mg-Mischmetal-Zn-Zr alloy compositions which are currently being produced commercially have been discussed in dytail by Nelson and Strieter,8,4 who also present some in- formation on a Mg-low Ce-Mischmetal-Zr alloy, and by Nelson.8 A patent issued to Jessup, Emley, and Fisher9 emphasizes the superiority of Mg-didymium-Zn-Zr alloys over the corresponding alloys made with Mischmetal. The purpose of this paper is to present the results of an extensive investigation concerned with the effect of increasing amounts of zirconium on magnesium sand casting alloys containing several different rare earth metal mixtures in varying amounts. The effect of the addition of zinc to some of these alloys is also being reported. Preparation and Testing of Alloys The alloys studied in this investigation were prepared in small laboratory melts according to the melting procedures described by Nelson1" as the Crucible Method. Electrolytic magnesium having the composition shown in Table I was used as the starting material. The rare earth metal alloying ingredients used in preparing these alloys were essentially of the compositions listed in Table 11. Some of the didymium-containing alloys were prepared using a Mg-didymium hardener. The rare earth metal content of this hardener analyzed 1.2 pct Ce, 10.4 pct Pr, 80.8 pct Nd, and 7.6 pct La. The zirconium was added in one of three forms: 1) as sponge zirconium obtained from the Bureau of Mines; 2) as a fused salt consisting of 50 pct ZrCl, and 50 pct alkali chlorides from which the zirconium is reduced by the magnesium; or 3) as a Mg-Zr hardener. The alloying procedures and melt hand-

Jan 1, 1958

By T. A. Wright

THE SAMPLING of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or "metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can be readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also.

Jan 1, 1928

By Ben L. Seegmiller

Artificial support of rock slopes in mining applications may consist of rock anchors with and without auxiliary support systems, but- tresses or shotcrete. The use of artificial support systems is not applicable in all cases of slope instability. Some pit slope problems simply cannot be cured with a support system. In other cases, a sup- port system which would solve the problem would be uneconomical. Rock anchor design may be undertaken using an active or tensioned system or a passive or untensioned system. Failure problems to which artificial support systems are most commonly applied include planar, wedge, rotational and toppling failures. Design of auxiliary support systems and rock anchor peripheral items may be initially estimated using analytical concepts, but field trials are commonly used to determine final requirements. Field procedures usually require a close coordination between mining personnel and the support installation team. Great care must be exercised during installation to prevent numerous potential problems including poor anchorage, excess bearing and corrosion. Displacement monitoring of the completed system is a must if the effectiveness is to be closely judged by means other than total slope and/or support system failure. The cost of a support system is relatively high when compared to other remedial measures that may be taken to solve a slope instability problem. Therefore, the system costs play a vital role in determining whether or not artificial support should be considered beyond the initial assessment stage. Case histories are few, but do include examples of each type of support system.

Jan 1, 1983