Search Documents

By W. M. Reilly, Martin E. True, O&apos

A technique, equipment, and a compound have been developed and field tested for sealing tubing joint thread leaks without removing the tubing from the well. This eliminates the necessity of killing the well with possible damage to the producing formation, which could result if it were exposed to drilling mud. A thread sealing compound, developed and tested in the laboratory, is introduced into the tubing and squeezed into the joint to eliminate the leak. A high percentage of successful field applications have eflected an appreciable cost reduction in repairing leaking tubing strings in East Texas and in the Louisiana Gulf Coast area. INTRODUCTION In producing oil and gas wells the industry has been plagued with a never ending problem of tubing connection leakage. This situation is becoming increasingly more significant as more gas wells are placed on production and as higher pressures are encountered at greater depths of current drilling. Substantial progress has been made in minimizing thread leaks by careful handling and cleaning of joints and by the use of improved sealing compounds in combination with controlled makeup. But even with the use of the best known methods and sealing materials during initial makeup, occasional leaks through tubing joint threads appear inevitable. In some instances, tubing joints in high-pressure gas wells have been found to leak gas at relatively less pressure than that at which the tubing had been tested satisfactorily using liquid. Many expedients have been employed to prevent the physical replacement of tubing when leaks have developed. Perhaps the most commonly used is the sodium silicate treatment in which the solution is lubricated into the tubing to form a crystalline plug in the leak. Generally, any benefit realized is of a temporary nature. In addition to field studies on handling and makeup of tubing, extensive laboratory work has been undertaken on the development and testing of thread dopes.' Also, substantial effort has been devoted to testing tubing joints using high-pressure gas as a pressure medium.' The results of this work have emphasized that tubing joints are susceptible to occasional leaks, especially when subjected to relatively high differential pressures. To cope with the problem of leaking connections, an extensive investigation was undertaken to devise means of sealing leaks without removing the tubing from the well and without reducing the inside diameter of the tubing. The purpose of this paper is to present a technique, together with the associated equipment and compound, which have been developed for effecting a seal of leaking tubing in place. DISCUSSION Work was initiated simultaneously on two ventures: (1) to develop a satisfactory leak sealing compound and (2) to develop tools necessary to find the leak and place the compound. Leak Sealing Compound In the development of a sealing compound, tests were conducted on those compounds commercially available which include: (1) conventional thread lubricants, (2) thermo-setting resins and (3) other materials which held promise of effecting a seal. Although none proved completely satisfactory in their available form, two commercial compounds proved nearly equally effective in sealing leaks during laboratory tests after proportioned quantities of graded silica had been added. Field usage has indicated that the preferred compound is one prepared of an aluminum-stearate base thinned to the proper constituency and carrying a mixture of fine mesh graphite and graded silica. The compound developed by Humble Oil & Refining Co. is designated as Tubing Thread Leak Sealant 800. Placement Tools and Technique In developing tools to detect joint leaks and to place the sealing compound, work was done initially on wireline equipment. Preliminary designs were completed of a tool somewhat on the order of a pressure bomb to test individual joints with gas at high pressure to determine if the joint was leaking. An entirely different tool equipped with opposed packers was intended for placement of the sealing compound at high pressures in each leaking joint. The application of these tools

Jan 1, 1958

R. Culver, Colorado School of Mines I appreciated Professor Starfield's presentation, because his approach to blasting research reflects my feelings that a lot of practical work can be done toward making short-term advances that can be used by the blasting industry. We should not forget this in our attempt to obtain solutions to such idealized problems as a mathematical theory of cratering. The blasting industry would like very much to have the efficiency of the basic blasting processes improved from the range of 20 percent up into the range of 50 percent. And many of these problems should be approached and attacked in the laboratories. Blasting research at the Colorado School of Mines for the past two or three years has been aimed at improving the pre-splitting process, because we feel it will become increasingly important to the construction industry. We have attempted to develop a unified theory of how pre-splitting works; and the more we investigate, the more variables we find. We may never obtain an entirely satisfactory theory of pre-splitting, but we have developed a tentative explanation. One of our first conclusions was that we are making very poor use of the explosive in current pre-splitting practice. But to appreciate this we must first consider how pre-splitting works. A series of parallel boreholes are loaded with low density charges which are detonated simultaneously. (Delayed detonation has been tried, but most people agree that simultaneous detonation is best, and this is what we found.) Stress waves traveling out from each borehole interact with the stress waves from the two adjacent boreholes influencing the direction of the fractures that occur and propagate from each borehole. It has been suggested in private communication with Mr. Wilbur Duvall of the U. S. Bureau of Mines, that the fracture between the adjacent boreholes is a result of the net particle velocities above and below the pre-split plane which tend to set up a net tension along the pre-split plane. Regardless of what the exact mechanism is that causes the fracture to propagate from one borehole to the next, we know that it, in general, relies upon an interaction of the stress waves. However, if there is a large compressive stress normal to the pre-split place, it can practically eliminate any possibility of obtaining the desired pre-split by preventing the desired fractures from getting started. Aside from obtaining a fracture along the pre-split plane, the other major aim of pre-splitting is to minimize the fracturing that occurs around the borehole. We do this by drilling a large hole and putting a small charge in the middle of it. This results in a badly decoupled charge which is very inefficient; most of the energy is used in compressing the air in the borehole. Out of discussions about how pre-splitting works, we decided that perhaps there was some other explosive geometry which would make more efficient use of the explosive, and result in optimizing the pre-splitting process. Starting in the laboratory with small plexiglas blocks, we found that a fully-coupled explosive charge of 5 grains/in. of PETN gave random fractures extending about I in. from the borehole. A 1/4 in. plexiglas plug fit into a 1/4 in. hole in a similar block with the same fully coupled charge gave random fractures extending out only about 1/2 in. due to the energy absorbed in fracturing the plug. If the plug was split longitudinally but otherwise using the same geometry, it was possible to drive a fracture about 2 in. in either direction from the borehole, with an even smaller amount of fracturing around the borehole.

Jan 1, 1967

By Russell G. Haworth

Three companies, United States Potash Company, Potash Company of America, and International Minerals and Chemical Corporation, are now operating potash mines and reGneries in the Carlsbad, New Mexico, area. The three mines are located approximately twenty miles east of Car1sbad. The deposits have been found ideal for mechanized mining methods. This summary has been compiled from information made available by the three operating companies. Prospecting Since outcrops of potash are nonexistent, prospecting is accomplished by drilling and coring of the salt section to establish the grade, thickness, and outline of the potash beds contained in the salt deposits. Information regarding the nature of the formations in the cover of 400 to 600 ft thick over the salt and potash beds is also obtained from drill cuttings in the same operation. By proper interpretation of assembled data the best location for shafts may be determined. The overburden varies in character but consists in general of interbedded shales, sand, gravels, limestones, and anhydrite beds. Water, in unpleasant quantities, especially in the sands and limestones, often completes the geologic section. Some of the shaftas in the area have been sunk without undue difficulties, others have been delayed by flows of water. Most of the shafts are concreted from the surface to the salt section. Each of the three mines in the Carlsbad area has one shaft for hoisting ore and one for hoisting men and supplies. Mining Methods Information acquired from initial drilling and prospecting affected the choice of mining methods. Since the tabular, slightly rolling deposits were similar to coal seams, the room-and-pillar system used in coal mining was adopted by all the companies. Pillars have not been removed in any of the mines on a large scale. One company has conducted experimental robbing of pillars in one restricted area. Where it is known that overlying strata contain water in large amounts, it is not considered practical to risk flooding of the mines by removing pillars without fill. Some thought is now being directed toward development of economical methods of filling for pillar recovery. The problem is not identical at the three mines and local conditions will govern the methods employed for eventual pillar recovery. The important point is that, with large reserves, it has not been necessary to resort to mining of pillars for adequate production. The ore deposits are laterally extensive but are irregular in shape and lie at a depth of 700 to 1100 ft below the surface. The major operations of all mines are on the same bed strati-graphically, except for the langbeinite level at International Minerals and Chemical Corporation. The deposits are apparently not connected and in many parts of the deposits being mined, "salt horses" or barren zones occur. From 400 to 700 ft of salt with minor beds of polyhalite and anhydrite lie immediately above the ore horizon. The ore differs from the salt only in the potassium chloride content and color due to small amounts of iron associated with the sylvite, giving the ore a somewhat mottled red and white cast. Thickness of the ore varies from 5 to 14 ft. Rooms and break-throughs in the mines vary from 24 to 40 ft in width, the overlying salt forming an excellent roof and providing safe mining conditions. Almost no timber is used in any of the mines for roof support. Drilling is normally the first step in mining the face of a room. Electric motor driven auger drills are used in the area. Jack hammers were used to some extent when the mines were first opened but the ore is easily drilled if bits are sharp and the coal type

Jan 1, 1950

By J. Pinto, F. Galasso

THE current emphasis in preparing boron fibers by reduction of gaseous boron compounds on a resistively heated metal wire substrate has renewed interest in the borides of those metals which have relatively high melting points and are available as fine wires. A knowledge of the structures and properties of the borides, which are formed when boron diffuses into the metal core during boron deposition, can be of assistance in the understanding of the boron fiber formation process and the fiber properties. Many of these borides are well-known and their properties have been measured. However, when an unidentified boride is found in the core, it may be difficult to establish its composition because of the small amount of material available, the preferred orientation effects on the reflections in its X-ray pattern, and the possible overlap of X-ray reflections if several borides are present in the core. For example. the proper indexing of the X-ray pattern of WB4, which was formed in the tungsten substrate core during boron fiber formation, was accomplished only after small single crystals of this boride were grown and X-ray precession investigations were conducted.' This note presents the results of a study of the phases formed in the core when tungsten, tantalum, and molybdenum metal wires were used as substrates in the boron fiber preparation process with particular emphasis on the identification and characterization of a higher boride of molybdenum analogous to WB,. Boron was deposited on resistively heated stationary 0.0012-in.-diam tantalum, tungsten, and molybdenum wires at 1050°C for various times up to 60 sec using boron trichloride and hydrogen as the reactant gases. After 60 sec of boron deposition the fibers were approximately 0.006 in. in diam. Examination of photomicrographs of fiber cross sections showed that the boron had diffused nearly to the center of the tungsten and molybdenum cores in 15 and 30 sec, respectively, and only halfway to the center of the tantalum core in 60 sec. X-ray diffraction photographs of the fibers indicated that it was also after 15 and 30 sec deposition times that the tungsten and molybdenum metal reflections, respectively, had disappeared from the X-ray patterns of the fibers. The patterns of the boron fibers produced using tantalum wire as a substrate showed that amorphous boron, TaB2, and tantalum metal were present after a few seconds deposition time and remained even after deposition times of 60 sec. Until a deposition time of 15 sec was reached, the tungsten substrate fibers contained amorphous boron,273 6WB, W2B5, and WB4 as well as tungsten metal, while the molybdenum substrate fibers contained amorphous boron, MoBa, Mo2B5, and molybdenum metal for deposition times up to 30 sec. Just before the molybdenum metal pattern disappeared, a pattern similar to that of WB, appeared, suggesting that a phase, MOB,, isomorphous with WB,, was present in the fiber. This same pattern was obtained from the product formed by heating a mixture of molybdenum metal and excess boron powder in a boron nitride crucible at 1960°C in an argon atmosphere. As was the case with the WBn pattern, this pattern could best be indexed on the basis of a hexagonal unit cell rather than the tetragonal unit cell Chrktien and Helgorsky reported for ~0~4,~ see Table I. The unit cell parameters for MoB4 were calculated to be a, = 5.214A, co = 6.358A. Assuming the space group P63/mmc and positions5 2M01 in 2b and 2MoII in 2c found for tungsten in WB~,' a logical structure for MOB, was determined using geometrical considerations to place the boron

Jan 1, 1969

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By V. C. Allison

Large-scale testing of the explosibility of coal dust as conducted by the Bureau of Mines in its Experimental Mine involves a large initial investment, and a high charge for maintenance and conduct of the test; in addition the work is necessarily slow because of the time required for the preparntion of the tests and the cleaning and repairing of the mine after each test. These tests have been made along practical mining lines that admit of a range of mixtures of dust varying from 5 to 10 per cent. and with gas as low as 0.5 per cent. increments. Because of the time and expense involved, efforts have been made to devise a type of gallery for laboratory use in which the results obtained in the Experimental Mine may be correlated as an aid in a study of dusts, the explosibility of which might be approximately determined quickly and at a minimum of expense. The explosibility of coal dust has been studied by a number of European investors, using small laboratory devices; among these may be mentioned the experiments conducted by Galloway, Vital, Hall and Clark, Abel, Mallard and Chatelier, Thorpe, Bedson and Widdas, Engler, Holwartz and Meyer, and Taffanel, results of whose experiments have becn reviewed by the Bureau of Mines.' The Bureau has conducted many tests with the Frazer-Cle1ncnt5 apparattus, which gives the pressures set up when the dust cloud within is ignited with a platinum coil or tube, heated to different temperatures, but for these tests the sample must be especially prepared as to size (200 mesh) and must be dry. Need for a Dust-testing Apparatus An attempt has been made to design an apparatus that may be used for checking and correlating the expcrimental tests. The first design was a wooden gallery, 8 by 10 in., inside cross section, and 12 ft. long, and having a number of strips along each side for creation of turbulence. The wooden gallery did not get beyond its period of calibration; it mas difficult to make the gallery sufficiently tight, for it was necessary that the top be removable in order that the gallery could be cleaned. In the use of the wooden gallery, however, sufficient operating data were obtained to be a guide in the design of a steel gallery having a circular cross-section. One of the features was a flap valve, at the closed end of the gallery, that would open inwardly thus preventing a reduced pressure within, caused by the cooling of the gases of combustion, and the explosions propagated much better than when the valve was not used; another feature was the determining of the best method for getting a cloud of dust simultaneously in all parts of the gallery, which was accomplished by the use of the concussion wave of a small quantity of powder or by the use of compressed air.

Jan 1, 1927

By A. T. English

X-ray dif action techniques were used to investigate ordering and domain coalescence for the B2 (CsC1) superlattice in this alloy. Essentially complete disorder is obtainable by drastic quenching. isothertmal ordering occurs very rapidly at temperatures between 565° and 680°C, only a few seconds being required for development of substantial long-range order. A very fine antiphase dormain structure, found in samples annealed for short times, undergoes coalescence with further annealing. Domain "size" is found proportional to (t)1/2 . This Yate law can be derived by adapting the formalism of Hillert's analysis 01- metallurgical grain growth. For this Purpose the material is descvibed in terms of a "Swiss-cheese " structure, consisting of two multiply connected, mutually intertwined domain volumes. The observed activation enevgy for coalescence, 70 kcal per g-atom, agrees with an estit~lated value ,for volume diffusion in disordered rrzaterial. It is suggesled that the experimental value vejlects the substantially disordered environment of mobile vacancies located in the moving antiphase domain boundary. The alloy Fe-Co-2V is bcc below about 900'C and orders into a B2 (CsC1) superlattice below about 730c It has important applications in magnetic components, including many requiring extensive cold rolling.* example, Marcinkowski and Brown6 observed a re1atively small as-quenched domain size of about 250Å in B2 Fe3A1. Since there appear to be no published data on domain coalescence in B2 alloys, this process was studied in detail. MATERIALS AND EXPERIMENTAL TECHNIQUES A commercial high-purity alloy, nominally 49 Fe-49Co-2V, was obtained from the Arnold Engineering Co. in the form of cold-rolled sheet 0.004 in. thick. Samples were annealed for 1 hr at 800°C in dry H2 to produce disorder and quenched into iced brine. They were then annealed in a nitrate-nitrite salt bath for various times at temperatures between 525° and 625°C. Estimates of the LRO parameter S and the APD size D were made using established X-ray diffraction techniques. Superlattice peaks are best observed using CoKa radiation, for which the value of (fFe-fCo) is maximized. Peak-to-background intensity ratio was improved by filtering CoKß from the incident beam to eliminate sample fluorescence, and by using a pulse-height analyzer. The LRO parameter S was computed from the ratio of integrated intensities I 100/I 200- Owing presumably to systematic errors associated with the presence of crystallographic texture and X-ray extinction, only rough agreement was obtained between experimental and theoretical (absolute) intensity ratios. For this reason certain experimental refinements (e.g., use of balanced filters) were considered superfluous and were omitted. Emphasis was placed on maximizing intensity in order to reduce the time taken to accurately determine the contour of the very small (loo), peak. This was done by point counting 105 counts at appropriate intervals. Background intensity averaged about 1200 cps.

Jan 1, 1967

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By Arthur Taggart

Recent jig practice has shown such marked departures from the pronouncements of the textbooks, particularly as to particle size recovered and size range of feed, as to make it desirable to reexamine the mechanism of jig action. This paper presents the results of such a study. The general conclusions of the Paper are: I. A jig bed is a bi-functioned as well as bi-parted body. The upper layer comprises a plastic stream moving slowly in a substantially horizontal direction from feed lip to tail board. It serves to rough out tailing and light middling and to pick up heavy middling and lift it out 01 the jig box. The lower layer acts as the ultimate separating means by absorbing concentrate and rejecting heavy middling. 2. The separating function of the lower layer is performed in three definitely diflerent ways, depending upon the relative sizes of the grains presented to it and those composing it. Experimental The experimental work consisted of close and long-continued visual observations of operating beds in a plunger jig, eccentric driven, and in determinations of the settling rates of various metal spheres through a quartz bed under various conditions of operation. Falling velocities were measured by an ingenious method devised by A. 6. Dorenfeld, a student in the Mining Department at Colum- bia. Spheres of different metallic alloys, 3/8-in. diameter, were cast with a short piece of fine copper wire frozen in to Serve for suspension-A short piece of black cotton thread was looped to the top of the wire to serve as an indicator. The set-up for a test is shown in Fig. I. The thread should be boiled, if necessary, to make it freely water absorbent. The piece of clean plate glass D is supported rigidly at the proper height in a vertical position. The white scale E is similarly supported behind the glass. At the beginning of a test, D is filmed with water by holding it (best with clean rubber finger cots) under running tap water. It is then clamped in approximate position and C, already wet, is laid across it and drawn straight and vertical with the upper end at or near the top of D, and the ball A slightly above the top of the expanded bed. The water film holds the string to the glass. For a test the string is released, its upper end position noted just after the top of the ball becomes submerged, when the corresponding time is read, and thereafter simultaneous readings of position and time are taken as desired. Results of the visual studies of the bed are given at the pertinent places in the following discussion. Results of the settling tests are summarized in Figs- 2 and 3. Definitions The name bed as used herein refers to the entire mixture of solids and water filling the jig box. A layer is a stratum of a bed composed of particles of substantially the same specific gravities. A granular product is long-range when it approximates a crushed or ground product limited as to upper size only; a short-rafzge product is one closely sized. A bed is loaded when operating with continuous feed and discharge of products; it is unloaded when pulsating norma11y but neither being fed nor

Jan 1, 1943

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By L. T. Sanchez, W. T. Rogers

This paper presents the results of a production experiment evaluating the effect of the use of oxygen in the bessemer converter with respect to its relation to blowing time, amount of steel scrap or cold pig iron which can be melted and teeming temperatures of the molten steel. THE simplest and probably the most efficient and economical means for producing steel from molten pig iron is the bessemer converter. This process is essentially a mechanism for bringing oxygen into contact with the molten metal thereby oxidizing the elements silicon, manganese, and carbon. The source of oxygen is that contained in the air and is limited by that amount. In theory, there is an intermediate chemical reaction due to the mass action of iron and air which is represented by the equation: 2Fe + O2- = 2Fe0 The FeO then becomes the oxidizing agent and reacts with the silicon, manganese, and carbon to produce silicon dioxide (SiO,), manganese oxide (MnO), and carbon monoxide (CO), in the order mentioned. The balancing of the various chemical reactions shows that in the ordinary bessemer process more than sufficient oxygen is delivered to satisfy these reactions, which indicates that a further increase in the oxygen content of the air would serve no useful purpose. In spite of this reasoning, however, it will be demonstrated that when melting stelel scrap, commercially pure industrial oxygen introduced into the normal air blast will permit the melting of a larger proportion of steel scrap than is possible with air alone and also will increase the production rate by a substantial reduction in blowing time. It will also be shown that when melting cold pig iron, it is possible to melt up to twice as much pig iron with the use of oxygen as can be melted without added oxygen with a nominal increase in blowing time. At the plant where this study was made, oxygen is purchased from a nearby supplier and piped directly into the plant. It is supplied to the bessemer converter by being introduced directly into the blast line through an automatic control system which may be adjusted by the bessemer operator or "blower." Normally, iron is supplied by five blast furnaces to an open hearth shop containing twelve 165-ton capacity stationary furnaces and a bessemer converting shop having three 30-ton converters. The molten metal from the blast furnaces is allocated to one shop or the other in a manner to best provide for maximum production. At various times, it is desirable to direct the maximum amount of available blast furnace production to the open hearth shop. This has the effect of reducing the production of the bessemer shop. When this condition exists, it is desirable to supplement the reduced iron charge at the bessemer with steel scrap or cold pig iron to the maximum possible extent in order to maintain high total ingot production. This condition becomes aggravated when one of the blast furnaces is taken out of production for any repair job and particularly for extended periods such as when relining is necessary. The purpose of the investigation and experimentation with oxygen was to determine whether or not it would contribute to increased flexibility in the use of the raw materials, molten iron, steel scrap, and cold pig iron. In addition to the effect of oxygen on flexibility of operation, it was also necessary to determine the relation of its use to production rate or "blowing time," final finishing temperature of the steel or "teeming temperature," and steel quality.

Jan 1, 1953

By C. S. Smith, L. H. Beck

KNOWLEDGE of the Cu-Zn constitution diagram was critically examined in 1944 by G. V. Ray-nor,1 who suggested the diagram reproduced in Fig. 1 as the best evaluation of available data. No pertinent work on the constitution has been published since that time, although a number of authors have discussed transformation kinetics and theory. Despite the large amount of work that has been done on the constitution of these industrially important and scientifically interesting alloys, minor uncertainties still exist. For example, it is still not possible to say definitely whether a two-phase region exists between the ordered and disordered forms of the 8 phase. A careful re-examination of the phase boundaries in this part of the diagram was therefore undertaken. Two methods were selected for the new investigation—quantitative metallography for the higher temperatures and precision lattice parameter measurement for lower temperatures. Because of the relatively narrow two-phase regions flanking the ß phase in these alloys, quantitative metallography is particularly suited for their examination, since the relative amounts of the two phases are very sensitive to their compositions. The method, however, is useless below about 350°C because of the inadequate resolution of the two constituents. Below 400°, however, the X-ray diffraction method is applicable, although it is of somewhat lower sensitivity in this system. The changes of composition that occur during quenching from above about 500°C entirely vitiate X-ray measurements at room temperature though they do not affect metallographic area measurements. The two methods overlap and supplement each other admirably. Both methods depend on the attainment of equilibrium composition of the two phases in a more or less intimate mixture and thus avoid the difficult problems of nucleation and long range diffusion involved in the conventional metallographic bracketing method. The alloys were melted from a master alloy made from re-electrolyzed cathode copper and Horsehead 99.99 pct Zn. Melting was done under a cover of either borax or charcoal and the alloys cast into a 7/8 in. sq graphite mold for the a-ß alloys or a 3/8 in. diam cylindrical graphite mold for the ß-? alloys. The a-ß alloys were rolled at 750°C to 5/8 in. sq; annealed for 24 hr at 800°C and quenched; then rolled and swaged at 200°C to 3/8 in. diam rods, annealed 24 hr at 200°C, quenched and cold rolled 2 pct reduction. This treatment was intended to obtain a small grain size and to produce many nuclei of the minor phase for growth on subsequent heat treatment. The unworkable ß-? alloys were given preliminary treatment by sealing in Vycor tubes in vacuum and annealing for 4 hr at 800°C followed by cooling in air. Samples of homogenized alloys were checked spectrographically for impurities, but the principal components were determined on samples subsequent to heat treatment. The impurities analyzed averaged approximately as follows: Ag, 0.0002 pct; Fe, 0.004; Si, 0.0008; Cd, 0.005; Mg, 0.0002; and Pb, 0.002. For metallography, samples of appropriate composition were cut into rods 5/8 in. long, sealed in pyrex tubes in vacuum and annealed for eight weeks at temperatures of 470°C and below, two weeks at 480°, 500°, and 600°C, and 4 hr at 700°C, followed by quenching in cold water. Temperatures were accurate to ±2°C. The cylinders were then machined to 8.7 mm diam and a slice weighing 1.5 g cut with a thin saw transversely from the center of each. This

Jan 1, 1953

By D. J. Pye

Certain high molecular weight synthetic polymers in very dilute solutions decrease water mobility in porous media 5 to 20 times more than would be expected from the solution viscosity. This indicates that increasing water viscosity to reduce adverse mobility ratios in water floods is economically feasible in many situations. Laboratory results are consistent with accepted theory with respect to improved areal sweep, permeability distribution and displacement efficiencies as would be predicted from the solution mobility measured in the core. The laboratory results have been confirmed by field pilot floods which recovered 80 per cent and 100 per cent more oil than comparative water-flood pilots in fields containing 16 cp and 130 cp oil respectively. Economic analyses based on pilot data indicate the method to be profitable. INTRODUCTION The desirability of improving the water-oil mobility ratio in waterflood-ing operations has long been appreciated, especially for high viscosity crudes. Methods of reducing the oil viscosity by application of heat, gas resaturation and miscible drives have met with some success. Conversely, it has been generally conceded that increasing the water viscosity would also be effective, but the amount of thickening agent required to effect an appreciable increase in viscosity is discouragingly high. The use of such materials as glycerin, sugar, or glycols is completely out of the question economically, so that considerable attention has been given to the use of the much more efficient synthetic water-soluble polymers as viscosity improvers; but even these materials are not economically attractive. If increased water viscosity could be economically realized, marked improvements in areal sweep efficiency, as discussed by Caudle and Wittel and others, would be realized in field operations. Similarly, the improved mobility ratio would bring about increased recoveries by correcting permeability distribution problems as discussed by Stiles2 and Dykstra and Parsons,' and improvements in displacement efficiency would be obtained as recognized by Buckley and Leverett4 and Welge.5 LABORATORY STUDIES THE RESISTANCE EFFECT In the course of research to develop a more efficient water-soluble polymer viscosity builder, we discovered that a very few types of water-soluble polymers exhibited a most unusual and very interesting property not previously observed. Among the earliest materials showing such activity were polymers containing acry-lamide. Fig. 1 shows a typical plot of the solution viscosity vs concentration for one of these polymer solutions as determined in an Ostwald viscometer. As usual, such a plot is an approximate straight line on semi-logarithmic paper. Now, an inspection of Darcy's law, shows that a viscosity value can also be determined in a formation sample if the pressure, flow rate and permeability are known. If the core permeability is previously determined with wa- ter or brine, then the viscosity of another aqueous fluid may be determined from the equation. The viscosities so determined for glycerin (glycol or polyvinyl alcohol solutions, for example) agree with the viscometer determinations. However, in the case of the water-soluble polymer solutions in which we are interested, the viscosities measured in the formation sample depart very markedly from the viscometer values. A typical relationship for a polymer solution is also shown in Fig. 1. This unusual departure from the expected response is referred to as a resistance property of the polymer and is quantified as "resistance factor". Since the resistance factor R can best be determined in a core under study, the term has been defined on the basis of the ratio of the brine mobility to the polymer solution mobility at residual oil saturation so that:

Jan 1, 1965

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By Charles H. Jacoby

In 1774 a Swedish chemist, C. W. Schule, first recognized manganese as an element. That same year Schule's associate, J. G. Gahn, isolated the element manganese for the first time. In 1856 the Bessemer process of steelmaking gave birth to the economic importance of manganese. Later, in 1882, Robert Hadfield discovered high manganese steels. Although the primary use of manganese is in the ferroalloy industry, two additional important uses for manganese are making chemicals and dry cell batteries. Manganese is also vital to plant and animal life. Various chemical compounds of manganese are used in fertilizers, feeds, glass manufacture, paints, varnishes, and for numerous medicinal and chemical purposes. For the study of industrial minerals and rocks, only the chemical and battery grade material is of- concern, but for the sake of comparison, metallurgical aspects are included in this presentation. Although currently the world's largest consumer of manganese, the United States is producing only minor amounts of ore at the present time. This is due primarily to the fact that although huge deposits of manganese occur within our borders, all are of such low grade as to be economically unfeasible to mine. For many years various government agencies and segments of private industry have devoted sizable sums of money and time in an attempt to upgrade ores from the various deposits, and also in an attempt to recover manganese from blast furnace slags. In view of current world prices, and the quantity of high grade material available, there is little likelihood that any of these approaches will be found to be economically feasible in the near future. Geology and Mineralogy Mineralogy There are over one hundred minerals that contain manganese. These minerals vary from those with compositions that are predominantly manganese to those having only minor percentages. [Chemical Mineral Composition % Mn Hausmannite Mn304 72 Polianite MnO2, 63.1 Pyrolusite MnO24 60-63 Cryptomelane KR8O16R (R=Mn) Variable PsilomelaneBa Mn Mn8O16 (OH).45-60 CoronaditePb R8O16R (R=Mn) Variable Hollandite Ba R8O16R (R=Mn) Variable Manganite Mn2O3•H20 62 Braunite 3 Mn2O3•MnSiO3 62 Tephroite 2 MnO•SiO2 54.3 Rhodochrosite MnCO3 47 Rhodonite MnSiO3 42 Spessartite 3 MnO•AI2O3•3SIO2 33.3 WadHydrous Mn OxidesVariable Franklinite(Fe Mn Zn)O(Fe Mn)sO3 Variable Asbolan Cobaltiferous wad Variable AlabanditeMnS63.14] Geology From a geological standpoint most manganese deposits are complex. In general, it can be said that all primary deposits of manganese are carbonates or silicates. The most productive and profitable have been those of sedimentary origin and residual concentrations. Examples of these residual types of deposits are associated with the metamorphosed lodes of Madhya, Pradesh, India, and the lateritic deposits of Orissa and Bihar, India; nodules in the residual clays of the Philippine Islands, US southern Appalachians and Arkansas, Ghana, and Brazil. Sedimentary manganese deposits are best exemplified by the Nikopol district of Russia and the Tchiatouri area of Georgia, USSR. Hydrothermal replacements are characterized by the rhodochrosite deposits of Butte and Phillipsburg, MT. In general, the hydrothermal type deposit has not resulted in any large tonnages being produced, but may have given

Jan 1, 1983

By M. W. Legatski, D. L. Katz

The best currently available description of the longitudinal mixing properties of a porous medium is an equation of the form which relates the effective longitudinal dispersion coefficient Dp to the molecular diffusion coefficient Do, the electrical resistivity factor F, the porosity <f> and a Peclet number. If the parameters dpa and m are determined for a porous medium of known porosity and electrical resistivity factor, then a dispersion coefficient may be estimated for a given flow rate and a given gas pair. A new method, featuring on-line gas analysis by thermal conductivity and on-line data reduction by analog computation, was developed and used to determine these mixing parameters for eight naturally occurring sandstones and two dolomite samples. The exponent m of the above equation was found to vary between 1.0 and 1.5. The characteristic length dpa in the above equation was found to vary between 0.25 and 1.9 cm, with an average value of 0.4 cm for sandstones. Measurements were made on two cores in which paraffin wax had been deposited by evaporation from a pentane solution. They indicated that the presence of an immobile phase such as connate water could increase the dispersion coefficients significantly. INTRODUCTION While the petroleum and chemical industries have studied the mixing of miscible liquids flowing in consolidated porous media and of miscible gases flowing in unconsolidated porous media, relatively little data have been presented to describe the mixing of gases flowing through consolidated porous media. Such data are of particular interest to the gas storage industry. For instance, the U. S. Bureau of Mines is storing large quantities of a rich helium-nitrogen gas in contact with a natural gas in a dolomite reservoir. Since the rich gas occupies only 15 percent of the total reservoir volume, it is essential that the extent of rich gas-natural gas mixing be predicted and understood as a function of rock properties, pressure and rate of movement. This investigation was concerned only with the determination of longitudinal dispersion coefficients. It is understood that a transverse dispersion coefficient, which characterizes mixing perpendicular to the direction of flow, may be an order of magnitude less than the coefficient characterizing mixing in the direction of bulk flow.5719 It should also be recognized that the use of any dispersion coefficient is in itself a simplification. It is necessary to assume that mixing in a porous medium may be characterized by the equation for flow in a single direction. A number of authors1 l8,19 have pursued the mixing problem, not in terms of the so-called "dispersion model" described by Eq. 1, but in terms of a "mixing cell model". This model supposes that a porous medium is constructed of a large number of small mixing chambers and that the concentration of the diffusing component within each mixing chamber is uniform. Fick&apos;s law (Eq. 1) assumes that there is no gross by-passing of one fluid by another, and that there are not stagnant pockets of gas in the system under consideration as discussed by Coats and Smith.8 These assumptions are not always valid for flow through porous media and it is important to recognize the limitations upon Eq. 1. The most serious limitation upon the assumption of Fick&apos;s law mixing in a porous medium is

By F. E. Jaumot, A. Sawatzky

IT as long been recognized that there is a need for accurate systematic data on diffusion in solids. Originally, such data were needed to check existing theories but, more recently, it would appear that it could be used most advantageously as a guide to, or a check for, much needed extensions of the theory of diffusion. The awareness of the conditions which are important to experimental accuracy, the availability of the materials for accurate experiments, and the techniques have improved to the extent that it would now seem to an experimentalist that, unless extensions of the theory are made which take into account the fundamental parameters of the atoms, the electrons, and the lattice in some detail, the field of diffusion will rapidly become an empirical or semi-empirical field. The present series of experiments was designed to provide accurate data on the diffusion of the elements of the IB and IIB subgroups in silver; that is, to provide data on the diffusion in silver of three face-centered-cubic elements with roughly similar chemical properties, but with different atomic or ionic sizes and, similarly, for three noncubic elements. The elements of these two subgroups have different valences, so that the data will not give any significant information on differences due to the crystal structure of the solute. The present paper reports data on the diffusion of copper and mercury in single crystals of silver; the data for the other elements of the IB and IIB subgroups were reported previously by the authors1&apos;2 and by Tomizuka and Slifkin.8 Experiment The general technique used was identical to that previously described1,2 and will not be repeated here. In all cases, the sectioning technique and high specific activity isotopes" were used. The short half-life of Cu64 made decay corrections more important than for the other isotopes, and necessitated around the clock shifts while data were being taken. Each section was counted at least twice (as was true for all longer half-life isotopes) and a monitor was counted along with each sample. Data for the diffusion of mercury in silver are presented at a greater number of temperatures than for the other solutes. This is a result of two circumstances. First, six (of 30) samples had to be discarded because of pitting or recrystallization which occurred during the diffusion runs, even though the samples had sustained high temperature prediffusion anneals. Either of these was a very rare phenomenon in the other experiments, and their occurrence in this case is considered in more detail below. Second, the curves of the logarithm of the activity of the sections vs the square of the penetration deptht were, in general, quite good, but frequently seemed to show one point to have high activity and the next point to have slightly low activity in terms of the best straight line. When this occurred, there was remarkable regularity of the high-low sequence. In any event, the results, as far as diffusion coefficients are concerned, were not affected by this amalgam effect. In fact, the mercury data had the highest internal consistency of any of the data. Results Diffusion of Copper in Silver—-Diffusion runs were made at eight temperatures In the temperature range from 700° to 950°C, for times ranging from 5 to 45 hr. A linear curve of the logarithm or the activity vs the square of the penetration depth was obtained for all samples. Table I summarizes the results for individual samples and Fig. 1 gives a plot 02 the logarithm of the diffusion coefficients as

Jan 1, 1958

By D. O. Wyble

Five water-driver fields, for which pressure predictions had been made within a few years after discovery, were re-studied when four to five years of additional pressure and production data became available. It was fortnd that forecasts of the pressure in water-dri~fe reservoirs may be subject to considerable unccrtainty. Predictions car be erroneous when there is insufficient presswe history to define the cllaracteristics of the aquifer, and when there are errors in the pressure, production or geologic data. INTRODUCTION The efficient operation of an oil or gas reservoir requires that the important characteristics of the reservoir be determined soon after its discovery. It is especially desirable to evaluate the pressure-production relationship quickly, for this relationship provides a basis for deducing the type of production mechanism that is operative, and for making pressure predictions. The pressure predictions, in turn, provide a basis for calculating efficient rates of production, determining whether water or gas should be injected, etc. The importance of pressure prediction is such that forecasts should be made as accurate as possible, and the limits of error well defined. Historically, pressure forecasts for some fields have proved very accurate, while for others the forecasts were so erroneous that they resulted in the adoption of wrong, or at best, unnecessary production practices. Pressure predictions made for water-drive fields are especially subject to error. Accurate forecasting for these fields requires that much be known not only about the reservoir proper but about the adjacent water-filled rock as well. The water-containing rock, or aquifer, may extend for many miles, and often there is only meager data regarding its thickness, permeability and porosity. Much of the information must be inferred from the previous pressure behavior of the reservoir. A brief pressure history may provide little information about the characteristics of the aquifer. Hence, pressure predictions made early in the life of water-drive fields can be incorrect. The work described in this paper was done to determine the degree of reliability which can be expected of pressure predictions made within a few years after water-drive fields are discovered. Five fields, for which the original pressure predictions had been based on less than seven years&apos; history, were re-examined with the aid of four to five years of additional pressure data. Where the predictions were inaccurate, the reasons for failure were ascertained. The studies were accomplished by use of the electric reservoir analyzer.&apos; The analyzer was first adjusted to repeat the original pressure-production match using the same values for the various parameters as were used in the original study. Then, the actual production rates experienced during the time elapsed since the initial study were set into the analyzer, and the pressure behavior indicated by the machine for this period was compared with that which actually OCcurred. Where the pressure profile traced out by the analyzer deviated from the observed field behavior, the analyzer was readjusted to obtain a better over-all match. The old and the new solutions were compared to determine the reasons for any differences. COMPARISON OF PREDICTED RESERVOIR PRESSURE BEHAVIOR WITH ACTUAL PERFORMANCE Field A The original pressure-production match is entirely adequate as evidenced by the pressure match of the field&apos;s history subsequent to Jan., 1952 (see Fig. 1)&apos;.

By Arthur Taggart

Recent jig practice has shown such marked departures from the pronouncements of the textbooks, particularly as to particle size recovered and size range of feed, as to make it desirable to reexamine the mechanism of jig action. This paper presents the results of such a study. The general conclusions of the Paper are: I. A jig bed is a bi-functioned as well as bi-parted body. The upper layer comprises a plastic stream moving slowly in a substantially horizontal direction from feed lip to tail board. It serves to rough out tailing and light middling and to pick up heavy middling and lift it out 01 the jig box. The lower layer acts as the ultimate separating means by absorbing concentrate and rejecting heavy middling. 2. The separating function of the lower layer is performed in three definitely diflerent ways, depending upon the relative sizes of the grains presented to it and those composing it. Experimental The experimental work consisted of close and long-continued visual observations of operating beds in a plunger jig, eccentric driven, and in determinations of the settling rates of various metal spheres through a quartz bed under various conditions of operation. Falling velocities were measured by an ingenious method devised by A. 6. Dorenfeld, a student in the Mining Department at Colum- bia. Spheres of different metallic alloys, 3/8-in. diameter, were cast with a short piece of fine copper wire frozen in to Serve for suspension-A short piece of black cotton thread was looped to the top of the wire to serve as an indicator. The set-up for a test is shown in Fig. I. The thread should be boiled, if necessary, to make it freely water absorbent. The piece of clean plate glass D is supported rigidly at the proper height in a vertical position. The white scale E is similarly supported behind the glass. At the beginning of a test, D is filmed with water by holding it (best with clean rubber finger cots) under running tap water. It is then clamped in approximate position and C, already wet, is laid across it and drawn straight and vertical with the upper end at or near the top of D, and the ball A slightly above the top of the expanded bed. The water film holds the string to the glass. For a test the string is released, its upper end position noted just after the top of the ball becomes submerged, when the corresponding time is read, and thereafter simultaneous readings of position and time are taken as desired. Results of the visual studies of the bed are given at the pertinent places in the following discussion. Results of the settling tests are summarized in Figs- 2 and 3. Definitions The name bed as used herein refers to the entire mixture of solids and water filling the jig box. A layer is a stratum of a bed composed of particles of substantially the same specific gravities. A granular product is long-range when it approximates a crushed or ground product limited as to upper size only; a short-rafzge product is one closely sized. A bed is loaded when operating with continuous feed and discharge of products; it is unloaded when pulsating norma11y but neither being fed nor

Jan 1, 1943

By N. T. Cotman, C. H. Pickering, P. B. Crawford

A beat-conduction model has been developed to study the flow of fluids in a stratified oil reservoir which is being subjected to unsteady-state depletion. To simulate stratification, plates of different metals were joined together so that cross flow could occur between strata. A description of the model, plate construction and necessary instruments is included. The data indicate that stratified oil reservoirs experiencing cross flow may be treated as a single, homogeneous, producing sand having properties intermediate between those of the layers making up the system. A technique for averaging core-analysis data to arrive at the proper average value of rock permeability and porosity is presented INTRODUCTION Although oil has been produced from reservoirs for 100 years and reservoir injection processes have been undertaken for 40 years, the industry is still inadequately informed on the problem of reservoir inhomogeneities. Stratification is perhaps the best-known type of reservoir heterogeneity. Urenl discussed the possible significance of this nonuniformity in his 1927 paper on the theoretical aspects of water flooding. Since this time the problem of vertical permeability variations has been the subject of much discussion and numerous papers. Levorsen2 simply describes the origin of layered beds in his Geology of Petroleum. Some beds are field-wide and may be traced from well to well, while others apparently pinch-out and become discontinuous. In addition, the physical characteristics of a layer may vary from place to place. For these reasons, a stratified system is not easily defined. In calculations involving oil reservoirs in which permeabi1ities vary, methods presently used contain many simplifying assumptions. The reservoir frequently is considered as consisting of permeable layers, each of uniform vertical and lateral permeability and each behaving as if separated from adjacent layers by thin impermeable layers. Other assumptions frequently made in reservoir calculations are steady-state flow conditions, unit mobility ratio, linear geometry, average or homogeneous porosity, and negligible capillary-pressure and gravity effects. Muskat3 has. developed solutions to the stratification problem for mobility ratios other than unity for both linear and exponential permeability distributions. He assumes lateral uniformity and continuity of all productive strata and does not consider porosity. This study will take into account transient effects, cross flow and varying porosity, as well as the variations in permeability, by means of a heat analogy. Muskat5 has shown the similarity of the equations which describe the flow of fluids in a porous medium to the flow of heat through a solid. Landrum, et al,6 made an analogy between the flow of fluid in an unsymmetrical reservoir and the conduction of heat in a similarly shaped metal plate. This analogy is summarized briefly as follows. If fluid is produced from an oil reservoir above the bubble point, the resulting pressure distribution will be identical to the temperature which would result in a metal or heat-conducting plate if heat were similarly removed. This means that a study of heat flow in stratified thermal models will behave like fluid flow in stratified oil reservoirs. For mathematical correspondencies, set- Ref. 6. The fluid mobility k/p is proportional to the thermal conductivity, and the porosity-times-compressibility product is proportional to the density times specific heat of the thermal plate. EXPERIMENTAL EQUIPMENT AND PROCEDURE The stratified reservoir model used in this study is illustrated schematically in Fig. 1. A Leeds and Northrup Speedomax Type G temperature recorder