Search Documents

By C. R. Hocott

THE viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,1,2 but no data have been published on the viscosity of repre-sentative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields.

Jan 1, 1940

By A. S. Malicsi, I. Iwasaki

Differential flotation of bulk sulfide concentrates from Duluth gabbro into copper and nickel concentrates could be implemented by first destroying the hydrophobic coating with ozone and then by recovering the copper concentrate with a copper-selective collector. A number of parameters involved in the use of ozone, such as the sequence and the conditioning time of ozone treatment, the pulp pH, and the level of xanthate addition, were investigated.

Jan 1, 1986

By Walter L. Crow

MUCH has been published on highly technical phases of grinding. Very little has been written on how a mill man can improve his operations by determining the optimum size assortment of grinding balls that should be added as a makeup charge. This ball rationing is not to be confused with the ball ration used as an initial charge when the mill is started up. Ball rationing is considered for one or more of the following purposes: 1) to increase throughput of the mill, 2) to reduce the power required per ton of ore ground to the desired size, 3) to reduce steel consumption per ton of ore ground, 4) to improve product size, and 5) to lower retention time of ore in the mill.

Jan 7, 1957

By M. E. Tyrrell, Alan H. Goode

The application of a simple, two-dimensional computer technique for evaluating rock burst potential in cut-and-fill stopes was investigated. The principal purpose of the study was to compare the effectiveness of high-modulus fill and destressing as aids in the control of rock bursts. Two conclusions that are probably of general applicability are drawn. First, high-modulus fill is ineffective as a means of increasing the mine stiffness and acts to control rock bursts only if it supports enough load to reduce substantially the stresses on the unmined vein material. Second, destressing is most effective if it is performed when the vein material is near the point of failure.

Jan 1, 1975

By E. P. Klier, V. Weiss

IN studies of the X-ray diffraction line geometry of iron with chromium radiation using techniques aimed at minimizing the background intensity, Kp and Ka emission satellites* were resolved with three techniques. These satellite lines are present with sufficient intensity to lead potentially to erroneous structure analysis, if not properly interpreted. The techniques used were: 1) film technique with un-filtered radiation and polycrystalline specimen, 2) film technique with unfiltered radiation and single crystal, and 3) counter technique with unfiltered radiation and single crystal. An example of results obtained with technique 1 is given in Fig. 1.

Jan 1, 1958

By A. K. Sinha

The market for thermal coal has recently been growing rapidly and it is projected to continue to do so in the foreseeable future. Both the national and international markets often demand high-Btu low-sulfur thermal coal in order to minimize the cost of utilization and meet the environmental restrictions. High quality thermal coal can be prepared to compete in the utility market by desulfurizing the high-Btu midwestern coal and blending it with low-sulfur western coal which is usually low in Btu content. The methods that can be used for optimizing the coal preparation plant operating parameters for physically desulfurizing coal are presented.

Jan 1, 1985

By Persifor Frazer

In his " Final Report," Vol. 11, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

By John A. Wolfe

The brightest spot in the mineral economy of the Philippines is the rapid development of reserves and production of copper. If economic conditions remain favorable and the political climate is encouraging, production of this metal should increase at a rate of 25% per year for several years, long enough to rank this country as one of the major copper producers of the world. In 1965 the copper content of the Philippine concentrates was approximately 60,000 tons. It should total about 80,000 tons in 1966. A major part of the increase will come from the rich Lepanto mine located in Mountain Province, North Central Luzon. Daily production of ore increased from 1200 to 2000 tons at the end of 1965. The ore, consisting of enargite and luzonite, averages nearly 3% copper and 0.12 oz. of gold per ton. It is an under- ground operation with a cutoff grade of 2%. The ore is associated with extensive silicification under a volcanic cap rock. Further expansion to increase ore production to 2600 tpd is under way.

Jan 4, 1967

By K. Stout, E. Van Eeckhout, L. Friel

Previous research at the Montana College of Mineral Science and Technology indicated that it is practical and economically feasible to place stiff back- fill in a cut-and-fill stope. This backfill would reduce wall closure and high stress buildup in pi1llars, thus alleviating rockburst potential. Three ;topes from the Sunshine Mine, of the Coeur d’Alene Mining District, were chosen for a test verification of this concept. Although the first stope was lever mined beyond the initial cut (for economic reasons), some vibrating wire stressmeter results were obtained and found to compare favorably with numerical predictions. Some other instrumentation devices were built and tested, but never installed .

Jan 1, 1984

ORE at the Jeffrey mine of Canadian John Mansville at Asbestos, Que., is hoisted by two 12 1/2 - ton capacity aluminum skips, counterbalanced. When the loaded skip reaches the surface it empties, via its sliding door, into a bin. Simultaneously, the skip tender, who operates at the 940 level, loads ore into the alternate skip from a 12 ½ -ton measuring pocket. This done, he sets the skips in motion. Problem: When moisture content of the asbestos ore is high, the ore, unknown to the skip tender, some- times sticks in the dumping skip, preventing complete discharge. Moreover, the sliding skip doors sometimes jam and stay open after the ore is discharged. If a skip in this condition is lowered, the result is either an overflow of ore, or the ore discharges through the open skip door, down the shaft. Spilled ore must then be mucked out of the spill pocket and hoisted in 2-ton cars. Cost is high, time is lost, and the shaft is sometimes damaged. Solution: A television apparatus was installed so that the skip tender might quickly spot improper door operation or hang-ups at the dumping station.

Jan 8, 1958

By M. M. Singh

Coal mine operators are obligated to mitigate or plan for subsidence under the new regulations. This paper presents the types of subsidence control measures that may be employed to meet these requirements, which include: changes in mining methods, strata stabilization after coal extraction, construction of specially designed surface structures and foundations to accommodate ground movements, and comprehensive planning and coordination of surface land use with underground mining. The basic principles of these techniques, along with specific procedures that may be followed to implement them, are briefly discussed. Subsidence control methods that are currently being investigated are mentioned.

Jan 1, 1985

Jan 11, 1951

By J. B. Goddard

Crystallization of ammonium paratungstate (APT) is frequently the last effective purification step in producing high-purity tungsten. However, crystallizer mother liquors are often several times higher in tungsten than predicted by the solubility of APT. The formation of heteropoly anions, particularly those containing phosphorus and silicon, is largely responsible. Solubility of tungsten in APT mother liquor can be linearly correlated with the concentration of these and other impurities. The problem can be overcome by direct treatment of the crystallizer feed solution with aluminum sulfate. By appropriate treatment, the aluminum hydroxide flocculates and is easily filtered, resulting in a purified low-aluminum crystallizer feed from which high APT yields can be attained.

Jan 1, 1985

Jan 1, 1931

By Mungo Park, C. Baring Horwood

This paper is intended, in the light of recent investigations, to call attention to some of the essential features of good practice in sampling and mine-valuation. Mine-sampling may be divided broadly into two classes: (1) development-sampling and cornputatioll of ore-reserves; and, (2) stope-sampling and estimation of stope-values. Development-Sampling. It is with development-sampling only that this paper deals— the term development being taken to mean the opening-up of a mine by cross-cuts, drives, connections, etc., preparatory to actual extraction of the ore for milling. In development-sampling the work of the sampler and the consequent estima-

Jan 1, 1909

[NORTH AMERICA UNITED STATES ALABAMA Birmingham CORD, Richard H DISMUKES, Edward B Citronelle PERRIN, Huey P Fairfield PAGEL, Herbert Ervin Huntsville ENG, Harvard KELLEY, Dean W WAGGONER, J B Mobile HORNER, William L PETROUTSON, Peter C Montgomery GAMBLE, Halbert R Redstone RAWLINGS, William E Tuscaloosa MASON, William L University CUDWORTH, James R JONES, Walter B]

Jan 1, 1961

By Charles P. Williams

The lead-bearing area of Missouri has been subdivided, geographically, into the Southeastern, the Central, and the Southwestern

SINCE it seems to me that guns are of greater importance in the art of casting than any of the other things that are made by it, and that they require more foresight and care because they need many perfections, I wish now to repeat certain useful and necessary precautions in corroboration, for though I have already spoken to you of them in some detail, the power has not been granted me to pass with one breath completely through a subject with many parts. Therefore it will not be wearisome to you to hear the same thing told again, because it will not be without amplification of some pertinent points. For this reason I have prepared the present discourse, which I have called admonitions. The first of these concerns the making of the pattern upon which the

Jan 1, 1942

By A. D. Fernie

Growing interest in pit crushing and conveying is evident from the recent many articles, technical papers, and new equipment development. Application of a pit crushing and conveying system is complex. Many factors, such as mine design, production scheduling, as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1986

By G. C. Fryburg, H. M. Murphy

ThE rates of oxidation of metals are usually obtained by heating the metal specimens in furnaces. Such a procedure is satisfactory for most metals. However, there are several metals that oxidize according to the reaction.

Jan 1, 1959