Search Documents

By Strathmore R. B. Cooke, Eugene L. Talbot

THE perfluoro acids and derivatives show unusual surface-active properties that qualify them as possible flotation reagents. They lower the surface tension of water from 15 to 20 dynes below that obtainable with the corresponding hydrocarbon compounds.1, 2 Fluorochemicals adsorb very strongly on solid surfaces to give films that exhibit larger contact angles than films of the corresponding hydrocarbons."' * The large contact angles probably result from the terminal —CF3 group. The perfluoro acids are made by electrolysis of the corresponding carboxylic acid in anhydrous hydrogen fluoride.5 From the perfluoro acids many derivatives may be obtained, such as amides, amines, alcohols, xanthates, ethers and esters and others. Since the fluorinated analogues of the conventional hydrocarbon flotation collectors possess enhanced surface properties, a few were selected for testing. Because a survey of all possible minerals and reagent combinations would be out of the question, hematite was chosen to represent a nonsulphide system and pyrite to represent a sulphide system. The fluorinated reagents used in these experiments were prepared in the research laboratories of Minnesota Mining & Mfg. Co. Some were synthesized especially for this research. They are not available cokmercially. Separation of Nonsulphide Ores: The separation of oxides from silica has always been a challenge to the flotation industry because differences in surface properties of the minerals are normally insufficient to produce clean concentrates. Oleic acid," rosin acids,' and amine salts% ave been used to considerable extent to effect separation of metal oxides and silica. The system hematite-silica was chosen to represent the nonsulphides both because of its difficulty of separation and because large tonnages of easily obtainable material are available, such as gravity concentration tailings and nonmagnetic taconites on the Mesabi Range. The wash-ore tailings used here contained approximately 35 pct iron after desliming. Samples of the material used in this work were part of the same lot used by Chang, Cooke, and Huch9 and were prepared in an identical manner. Reagents for Nonsulphide Ores: Since one of the purposes of this investigation was to compare hydrocarbons with fluorocarbons, reagents of known behavior such as oleic acid, and the alkali metal salts of certain resin acids (Dresinates), were established as standards. Hydrocarbons and fluorocarbons of comparable chain length and other experimental fluorocarbons were tried as collectors for hematite. A list of the materials used and the concentrations of their stock solutions are given in Table I. Since silica can be selectively floated from hematite by conventional reagents," a few fluorocarbon reagents were also tried for this purpose. Their composition and concentrations are given in Table 11. Most of these reagents served the dual function of collector and frother. In the case of F-11 flotation did not occur but it served as a frother when F-6 was employed as a collector. Reagent grade sulphuric acid and sodium hydroxide were used to regulate the pH. Deionized water containing less than 0.1 ppm of salts expressed as NaCl was used for all solutions and flotation tests. The pneumatic flotation cell consisted of a 350-ml fritted glass Buechner funnel with a source of filtered air which could be controlled by a needle valve." A 50-g sample of ore and 250 ml of deionized water were added to the flotation cell and stirred slowly. The reagents were added and the pulp was conditioned before air was admitted to the cell. Approximately 15 ml of the pulp were removed for pH determination before flotation was started and were then returned to the system. The pH was again measured after flotation. Air was admitted to the cell until no further flotation occurred or until the character of the float changed markedly. Both the float and the nonfloat products were filtered, dried, weighed. and assayed for iron. The cell was washed in hot water and rinsed with deionized water after each test. Occasionally the cell was cleaned with concentrated hydrochloric acid to remove iron oxide particles from the glass frit. Experimental Results: Above a pH of 8, sodium oleate was an effective collector for hematite. The emulsification of equal parts of heavy fuel oil (20"

Jan 1, 1956

By G. E. Keller, G. D. Coe

Several methods have been devised for rapid determination of sulfur in coal using a high-temperature combustion furnace. The fundamental principles of the various methods are similar but the techniques vary widely. The method described herein is no different in principle from some of its predecessors but varies considerably in technique. Originally devised to overcome the low-accuracy criticism leveled against the others, the tube-furnace method has proved successful for limited applications. Work is being done to widen the applicability of the technique. Subsequent to the work of A. Vita1 in 1920, a number of investigators have published data dealing with the rapid determination of sulfur in coal using a high-temperature combustion furnace.2-5 These, together with several unpublished methods, involve wide differences in technique although they are all similar in principle. Investigation of typical details of procedure showed that poor precision or accuracy could be attributed to one or more of the following: 1) inadequate quantity of sample to be representative, 2) a delivery tube temperature too low to confine condensation to a washable area of the tube, 3) no provision for back washing the delivery tube, 4) incomplete absorption of the sulfur compounds due to inadequate bubbler, and 5) the false assumption that all of the sulfur is evolved as sulfur dixoide. The method herein discussed is no different in principle from some of its predecessors; the differences are in technique. Although the method is rapid—a determination can be completed in 5 min— accuracy has riot been sacrificed in order to achieve speed. MATERIALS AND EXPERIMENTAL WORK Fig. 1 shows the arrangement of the equipment. A metered volume of oxygen is passed through calcium chloride for removal of moisture, then through Ascarite for removal of carbon dioxide, and thence through a glass tee to the feed end of the combustion tube. Connected to the side arm of the glass tee is a rubber tube that is closed with a pinch clamp during combustion of a sample. The products of combustion are expelled through a Vycor bubbler, the end of which is submerged 3 cm below the surface of a 1 pct hydrogen peroxide solution contained in a 300 ml high-form beaker. At the completion of the 4-min combustion period the contents of the beaker are titrated to a yellow end point, using a methyl red indicator, with 0.05 N sodium hydroxide (or sodium tetraborate). The pinch clamp on the tube leading from the tee in the oxygen line is then opened and mouth suction applied to draw the hydrogen peroxide up into the bubbler past the ell, almost to the rubber tube connecting the bubbler to the combustion tube. This washing of the bubbler is repeated until no further acid reaction with the indicator is obtained. The hydrogen peroxide-sul-furic acid solution is then titrated to the final yellow end point. Test work conducted at the Robena Laboratory disclosed the following critical conditions that had important bearing on the precision of the method: Weight of Sample: Several series of tests wherein the sample weight ranged from 0.1 to 0.5 g of -60 mesh coal showed that the lowest variance (standard deviation squared) resulted from the use of 0.5-g samples; the variance was slightly greater when 0.3-g samples were used, and with less than a 0.3-g sample weight the variance increased rapidly with decrease in weight. Although the use of a 0.5-g sample invariably resulted in a very slight explosion as soon as the sample entered the hot zone of the combustion tube, this did not detract from the precision of the method. Temperatures: Mott and Wilkinson5 found that a combination of low temperature (1250°C) and low oxygen flow rate (less than 700 ml per min) tended to give high results due to formation of oxides of nitrogen. Although the method herein employs a much higher oxygen rate than 700 ml per min, as an additional precaution to assure accurate results, 1315°C (2400° F) is recommended as the most desirable furnace temperature. The temperature of the elbow of the bubbler should be at least 75°C to minimize condensation

Jan 1, 1961

By Charles A. Ashburner

At the Philadelphia meeting of the Institute, held in February, 1881,I had the honor of reading a paper on "A New Method of Mapping the Anthracite Coal Fields of Pennsylvania."* At that time the State appropriation for the Second Geological Survey had just expired, and, as a new appropriation was not assured, no detailed plan had been adopted by Professor Lesley, State Geologist, for the practical examination of the mines, and the solution of the geological structure of special localities, or the representation in sections, vertical and columnar, of the general structure of the coal basins and coal beds. I had merely proposed a plan of mapping, as the material for the construction of maps was most available, and it was at that time uncertain what money the Survey would have to enable it to extend the surface and underground explorations, in order to make the examinations complete. After a continuation of the Survey was authorized until January, 1884, by the legislature, in May, 1881, the Anthracite Survey was regularly organized, and a plan adopted for a systematic and exhaustive geological and mine examination of the region. This plan provided for such work, other than that of mapping, as was necessary for a complete and practical geological and mining survey of a coal field. To do any geological work, of however general a character, it was absolutely. necessary that the members of the Survey Corps should obtain unrestricted access to all the mining records of the operators, which have been made with great care and accuracy and at an enormous expense during the past thirty years and more. The unanimous and generous support of the individual and corporate coal operators, of the plan of carrying on the Survey, was promptly assured, on condition that the results should be of such a character as to render them of practical utility to the property-owners and those directly interested. It was hoped

Jan 1, 1883

By E. C. Harder

AT a Meeting of the New York Section, on May 23, 1918, the sole subject of discussion was the nature and occurrence of iron ores in certain parts of the world.? Owing to the importance of this subject, it has been deemed' advisable to publish the remarks made at that meeting in the form of a paper, for presentation at the Milwaukee Meeting, instead of in the usual place, under News of Local Sections. The remarks related to the following districts: Brazil, by E. C. Harder, of the U. S. Geological Survey; Scandinavia, by Waldemar Lindgren, of the U. S. Geological Survey; Cuba, by C. M. Weld, of the U. S. Bureau 'of Mines; Southern Europe, by A. C. Spencer, of the U. S. Geological Survey; China, by H. Foster Bain, of the U. S. Bureau of Mines; Alsace-Lorraine, by Sidney Paige, of the U. S. Geological Survey. BRAZIL By E. C. Harder During the years immediately preceding the war, the iron ores of Brazil were attracting the attention of iron operators both in Europe and in the United States. This was clue to the large quantities of practically undeveloped ore available, and to its great purity. It is reasonably safe to state that had capital not been diverted from the exploitation of these deposits to war purposes, Brazilian iron ores would probably now be offered in European and American markets. It is certain that after the war these ores will play a prominent part in the economic reconstruction of Europe and perhaps in the development of America.

Jan 9, 1918

THE Copperton mill in reality was a sort of proving ground. It was. designed to serve three purposes: (1) to verify the accuracy of the mine sampling by actually treating substantial tonnages of ore, (2) to demonstrate on a reasonably large scale the percentage of the copper in the ore that could be recovered, and (3) to permit the testing of various kinds of machines and devices for crushing and concentrating the ore, so as to guide the engineers in designing the proposed 6000-ton milling plant at Garfield. As a matter of fact, it contained a lot of second-hand equipment sent by MacNeill and Penrose from the works of the United States Reduction &Refining Co. in Colorado; and it was by no means a model installation. Probably it would have been even less efficient, except for the skillful work of George O. Bradley and-Frank-G, Janney, both of whom had worked with Jackling at Mercur. Bradley was a mechanical engineer employed to design the plant. Later he directed the design of the concentrator at Garfield and remained as consulting mechanical engineer to the company until 1915. Janney, who afterwards became manager of mills, a position that he retained until his death in 1916, was a skilled mechanic at the Golden Gate mill at Mercur when Jackling built the plant in 1897. His flair was making machinery do what it was intended to do. He was not an ore-dressing engineer in a technical sense; but Jackling him- self was a specialist in this respect as well as in designing and construction and Janney's mechanical aptitude made him a particularly valuable man in the Utah organization. John McDonald, another of Jackling's Mercur associates, was the first mine superintendent. With practically all of the available funds earmarked for construction of the Copperton

Jan 1, 1933

By T. Carl Shelton

The coal industry of the United States in 1967 had reasons to be both exuberant and concerned about its present and future role in the economy of the country. Continuing a momentum that began in the early 1960's, the industry has moved ahead in providing competitive customized products to strengthen its long-term domestic and foreign commitments, and has maintained with steady progress its position as a major supplier of energy. On the other hand, the industry must overcome air- water pollution and conservation-reclamation problems that have been identified by 1967 legislation. Throughout the year, the industry was characterized as "progressive," "healthy" and "dynamic." To have been termed a "growth industry" in 1967, is an accolade the coal industry can accept with pride. Culminating its efforts throughout the decade, the industry has emerged with a competitive image that is representative of its future strength.

Jan 2, 1968

By Jerome Strauss

IN his review of developments in 1943, Gilbert Seil, Chairman of this Committee on Reduction of the Ferroalloy Ores, tabulated the consumption of the alloying metals in relation to the steel production of that year. In the year just closed the approximate tonnage was of the same order, differing only to a minor degree or suffering some correction with more precise figuses available, as indicated in the following estimates: Consumption Metals in Tons Steel 92,000,000* Manganese 700,000 Silicon 200,000 Chromium 200,000 Nickel 75,000 Molybdenum 20,000 Tungsten 8,000 Vanadium 1,700 Titanium 1.600 Boron 10 `Production figure. The technologic studies instituted during 1942 and carried forward with such great vigor during 1943 continued into 1944 although in some instances were brought to a close either by completion of the specific development

Jan 1, 1945

By K. A. SPENCER

THE production of soft coal from strip mines in the United States has shown a remarkable growth in the last sixteen years, increasing from one and one-quarter million tons in 1914 to approximately twenty-two million tons in 1929. This is a growth of approximately 1660 p& cent, as compared with a growth of approximately 20 per cent in the underground mines for the same period. But even with this marked in- crease the total tonnage produced by open-face mining represents only 4 per cent of the nation's soft coal tonnage.

Jan 1, 1931

Jan 1, 1947

Jan 1, 1947

By George E. Thackray

In December, 1894, the Cambria Iron Company made a number of heats of Bessemer steel to be used in structures by one of its customers, subject to inspection and tests by a firm of consulting engineers, one of the requirements being that the material should riot exceed .08 per cent. of phosphorus. In other respects the requirements were such that they could only be met by material of good quality; but the general spe cification is not introduced here, as it is not the purpose of this paper to deal with anything except certain difficulties encoun tered in determining the phosphorus-content of the material in a manner satisfactory to both seller and buyer. Preliminary determinations of phosphorus were made in sample-ingots from each of the heats from which material was rolled for the order in question, and these preliminary chemical tests, made in the laboratory of the Cambria Iron Company, showed that, with very few exceptions, every heat was within the prescribed limit of phosphorus. After the material had been rolled, sample-drilling8 of finished material were taken from the various heats in the regular manner in use at the works, these samples being thoroughly mixed and divided into two parts, one of which was analyzed at the works' laboratory and the other sent to the inspecting engineer. Several hundred determinations were made from this mate rial without reaching an agreement between the work of the inspector's chemist and that of the works' chemist; but as it is not the object of this memorandum to treat of this part of the subject at length, it is considered sufficient to present herewith only a few of these first determinations. The analyses given in Table I. are those of the original series made on the heats which were afterwards resampled for final determination by an arbitrator; and they are selected for this reason, as the entire " comparison is thus rendered more complete.

Jan 1, 1896

By J. F. Wolff

During the past 4 or 5 years, much has been added to the detailed geologic knowledge of the Mesabi Range. This has not been in the direction of discovery of any new fundamental facts, but of detailed study, subdivision and correlation of different parts of the whole formation and of individual orebodies. Prior to this time, mining engineers in the district were so engaged with the commercial interests of exploring and developing orebodies that close geologic study and subdivision were done in a few instances only. The demand for refinement of work in .this direction has led 'the engineers of the Oliver Iron Mining Co. to do extensive structural subdivision and correlation in all exploration work during the past 4 years. Such work has become a commercial necessity rather than a scientific refinement, and at the present time is being extended to all parts of the Range. In the summer of 1914, the author of this paper wrote a series of articles on the orebodies and special features of the Mesabi Rangc, which was published in the Engineering and Mining Journal, issues of July 17 to Aug. 7,1915. Since that time studies of subdivision of the iron-formation have been extended considerably. The principal feature of this paper is the presentation of the subdivisions of the iron-formation. To this is added a discussion of the relations of the orebodies to the gentle folding and fracturing of the formation, and special features of the Range. The outline will be as follows : I. General geology. 11. Subdivision of Biwabik iron-formation. 111. Relation of orebodies to folding and fracturing of the iron-formation. IV. Special features. Acknowledgnlent is due to W. J. Olcott, President, and John Uno Sebenius, General Mining Engineer, of the Oliver Iron Mining Co., for permission to use the information presented in this paper.

Jan 1, 1917

By J. P. Myers, A. H. Flagg, E. S. Mardock, J. L. P. Campbell, J. M. Terry

The development process for the use of radioactive tracers as a means of locating zones of permeability is discussed. The general techniques for the safe handling of radioactive materials is given as developed by the Lane-Wells Co. and Well Surveys, Inc. The prob1em and. successes with tracers in waterflood systetns, oil and gas injection profiles, fracture sand tracing, squeeze (ement tracing. lost circulution, and cement top localion are discussed and illustrated. INTRODUCTION The exact location of the permeable zones lying within the productive horizon has been a major problem faced by the petroleum engineer for decades, and it has been a problem which has seldom been solved with certainty. Reservoir engineers usually have to incorporate a question mark in their estimates of future reservoir performance because of blanks in the core data. Although the use of radioactivity or electrical logs for the estimation of porosity has been of great assistance in furnishing a record for the reservoir engineer, this application of logging data has not completely solved the problem. In short, the industry needs an in-situ well surveying method which can locate and estimate the permeability of the zones existing within a given pay section. The initial development work with radioactive tracers has been towards filling the need for permeability information. Progress to date permits the location of permeable zones with a qualitative estimate of their relative importance with respect to permeability. The calibration of the method is still incomplete. but present development work on tracer preparations, borehole effect correction factors, and instrument limitations give a promise of quantitative "permeability profiles" in the near future. The development work on the radioactive tracer method discussed here began several years ago in the laboratories of Well Surveys, Inc., in Tulsa. At the outset of this work, three approaches to the problem were visualized as follows: 1. A fluid carrying a soluble, chemically inert, gamma ray emitting isotope is pumped down the borehole and out into the permeable zones of the formation. The greater gamma activity of the permeable zones thus permits them to be differentiated from the impermeable zones which contain no active tracer. It was found difficult to obtain a tracer material which was chemically inert. Absorption to some degree was noted in all experiments. Also, it proved impossible to hold the tracer near the horehole where it could be logged. 2. A fluid carrying a soluble, gamma ray emitting isotope is pumped down the borehole into the permeable formations. In contrast with proposal 1, above. the tracer is chemically active with the fluids and materials in the pore spaces of the permeable zones. The permeable zones are thus indicated by their higher radioactivity level. The main difficulty in this proposal was finding a tracer material which would not be absorbed by shale as well as in the permeable porosity. Very little field work was done with this system. 3. Radioactive particles suspended within the injection fluid are pumped down the well. As the fluid enters the permeable formations, the radioactive particles are filtered out on borehole wall. The permeable zones are differentiated from the impermeable by the gamma ray activity deposited on the formation wall.

Jan 1, 1956

By J. D. H. Strickland, K. J. Jackson

IN previous papers' ' details were given of the constructlon and use of an apparatus to study the rate of chlorine consumption and the rate of sul- fate and sulfur production when dilute aqueous chlorine solutions were allowed to react with pyrite and galena in acid solutions at or near room temperature. The reaction with pyrite was very rapid, and hence entirely transport-controlled in its kinetics, and produced only ferric and sulfate ions. The behavior of galena was much more complex and was studied in some detail. Sulfur monochloride could be detected as a reaction product and both

Jan 1, 1959

By L. L. Wyman

SINCE the observations of Heyn,1 relative to the embrittlement of copper after having been heated in hydrogen, this subject has received considerable attention from later investigators. The published works of Archbutt2 and of Bengough and Hill3 give the reasons for this embrittlement-the formation of steam by the reaction between cuprous oxide and hydrogen. From Ruder,4 Pilling,5 Moore and Beckinsdale,6 Bassett and Bradley,7 and from Smith8 can be obtained quantitative data concerning the action of hydrogen and other reducing gases on copper samples having various oxygen contents. This problem has been discussed from a practical standpoint by Fuller9 who calls attention to some of the instances of this embrittlement encountered in the manufacturing field. The examples he cites may be considered typical cases of copper embrittlement which were incident to the process of manufacture. In many cases, such difficulties are overcome by changes in the manufacturing process.

Jan 1, 1931

By GORDON H. FISHER

During the year 1945, the drilling pace in West Texas increased above that in the year 1944, and represented the highest number of well completions since 2941. The 1680 new wells drilled 8,287,958 ft. of hole for a per well average of 4933 ft. This depth is approximately 30o. ft. deeper than the average for the year 1944. Although the deepest well drilled in West Texas (Phillips Petroleum Company's Ada Price No. 1, in Pecos County) was completed during the year. 1944 to a depth of 15,279 ft. and tested the Ellen-burger horizon, the producing depth record for West Texas was set during the year 1945 with the completion of Amerada Petroleum Corporation's Jones No. I-A, in the Jones Ranch field, Gaines County, which now is producing at 11,422 ft. from the Devonian formation.

Jan 1, 1946

By W. E. Brigham, P. W. Reed, J. N. Dew

By J. F. Fidiam, T. F. Ford, A. G. Loomis

It is only within the past 10 years that serious attempt appears to have been made to improve rotary drilling fluids by the application of the principles of colloid chemistry, although the use of chemicals to control the rheological properties of clay slips has long been known in the ceramic industry. The main difficulty apparently lay in the lack of a complete analysis of all of the functions of a drilling fluid in the drilling of the well, together with the lack of adequate consideration of how colloid science could be applied to secure these ends, and particularly how apparent antithetical properties of the fluid could be compromised. Thus one analvsisl of the many requirements of a drilling fluid proved conclusively that the viscosity should be low, in order that cuttings and entrained gas might be eliminated effi-ciently in the settling ditch, while the loss in carrying capacity accompanying low viscosity could be regained by increasing either the density of the mud or the upward velocity of the mud stream in the annular space of the well, and the danger of sticking of the drill stem due to rapid settling in case of enforced suspension of drilling operations could be eliminated by enhancing the thixotropic properties of the fluid. The desired properties of the drilling fluid having thus been established, it was a natural step to treat the fluid with vis-cosity-reducing chemicals, such as salts of weak organic acidsl for example, sodium tannate or gallate—and to adjust the pH to the alkaline side to such a degree of thixo-tropy as would give low viscosity and low yield point under the conditions of flow prevailing in the settling ditch, but rapid gelation and high yield point when quiescent in the annular space during shutdowns. In fact, flow in the settling ditch should be just short of turbulent while flow in the well, together with the flow of mud past the cuttings, is practically always turbulent. The use of chemicals other than those mentioned, such as Calgon (sodium hexametaphosphate) and certain other phosphates together with sodium tannate, has now become standard practice and it is the consensus that this method of treatment has proved to be an important step in the development of the art of drilling oil wells. It is safe to assume that the application of colloid chemical principles can also help in solving other outstanding problems of drilling fluids, such as the development of cheaper and more efficient viscosity reducers ; the development of chemicals that do not lose their effectiveness in a short time during drilling operations; the finding of chemicals to preserve the plastering properties of muds when concentrated brines are encountered or in drilling through salt beds; improvement in the plastering properties of poor muds by further defloc-culation, and, conversely, the prevention of excessive deflocculation of certain marine shales sometimes encountered; the preparation of muds suitable for the successful drilling of heaving shale formations; the finding 0f chemicals to treat the mud to prevent or to diminish lost circulation; the development 0f muds that will not impair 6

Jan 1, 1941

By O. W. Ellis

Before entering upon a general discussion of the fascinating, but at present rather controversial, subject of gases in copper, the author feels that some attention should be directed to the work which has been carried out on the solubility of gases in metals. The outstanding contributions to our knowledge of this subject have been made by Sieverts and his collaborators(1) † and by Iwasé.(2) Both the German and the Japanese investigators employed apparatus of the same general design in their investigations. Full reference need only be made, therefore, to the German scheme, which is diagrammati-cally illustrated in Fig. 1. This, to use the words of Sieverts, which he employed in describing his arrangement of apparatus at the 1928 meeting of der Deutschen Gesellschaft für Metallkunde(10): shows a diagram of the usual mode of procedure. A quartz flask contains the metal (for high temperatures a highly refractory porcelain tube is used) and is connected with the rest of the apparatus by means of a stopcock. The other parts consist of a burette divided into 1/10 c.c., a leveling tube, and an adjustable mercury reservoir. The burette is connected on one side with the gas inlet and on the other side with the absorption flask; the connection can be interrupted by means of suitable taps. Another tap permits the connection of the flask and the Töpler pump. In an experiment the quartz flask is first exhausted and then a measured quantity of gas is let in from the burette. In the first place the volume of the flask when empty is found by calibration with an inert gas. The pressure is read off on the level tube of the burette, and the temperature measured by means of a thermocouple whose welded junction lies close to the outside of the quartz flask, which is heated in an electric furnace. In several experiments the quantity of absorbed gas was transferred to a burette by means of a pump and measured. Care was taken by Sieverts to cool the ground-in joint between the reaction flask (or tube) and the rest of the system. Suitable precautions

Jan 1, 1934

By G. R. Fitterer

NONMETALLIC inclusions in steel have received much attention by metallurgists during the past few years. Many investigators have been emphatic in stating their belief that these impurities are the chief causes of steel failures, while others think that their effects are negligible. One of the main reasons that definite information on the effects of these impurities is lacking is that no reliable method has been developed for the exact determination of the amounts of these different impurities in steel. Some valuable new information has been brought out by a reliable method for nonmetallic inclusions which has been developed at the Pittsburgh Experiment Station of the U. S. Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board. This procedure satisfactorily extracts some of the more common inclusions from steels, thus enabling the investigator to correlate steel failures with inclusion content. Although the data given herein are the first to be published on the subject of the electrolytic extraction method, the interest in the subject is evidenced by the fact that it is already being used by some 20 to 30 steel companies for their various purposes. Some of the comments received from these laboratories indicate that the method is highly satisfactory: the unfavorable comments, when traced to their sources, have been found to be based on some small mistake made in either installation or operation. The chief discrepancy seems to have occurred in attempts to apply the method to the extraction of inclusions from alloy steels. The procedure can be used only for the plain carbon steels and for such low alloy steels as those containing the usual amount of copper (0.2 to 0.3 per cent). Steels containing the carbide-forming alloys such as chromium, tungsten, etc., present far too many difficulties for the accurate determination of inclusions. Luckily, the iron and manganese carbides do not offer any difficulties and no contamination of the oxide-sulfide residue results. It is highly probable that some modification of the following

Jan 1, 1931