Search Documents

By Joseph J. Wallace

1. The Investigation shows that there are six coal beds of major importance in McDowell County from the standpoint of present production - Pocahontas No. 3, Pocahontas No. 4, Pocahontas No. 5, Sewall, Beckley, and Pochontas No. 6 - and five beds of minor importance - Iaeger, Douglas, Welch, Pocahontas, No. 9, and Eagle. The Pocahontas No. 3 bed contains the largest remaining, known reserves. 2. Known measured, and indicated reserves in all beds, based on a minimum thickness of 174 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 2,217 Trillion short tons as of January 1, 1951. Of this total, 1,731 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these area, such reserves should be added to he total estimated reserves.

Jan 1, 1952

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90°F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962', using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

By M. Drozd, M. Somppi, Z. Yamak

"Granular activated carbon is widely used in the gold mining industry for gold extraction from aurocyanide-containing slurry. The extraction process can employ carbon as part of the gold recovery operation for various circuit designs including carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) circuits. However, various qualities of activated carbon exist and the durability of the material can change significantly from source to source. Handling this expensive reagent can pose challenges when fine carbon losses occur in the CIP, CIC, and CIL circuits. Additionally, any gold that is adsorbed to these carbon fines can also be lost by various mechanisms including carbon attrition and fracturing, inefficient coarse-fine separation, and poor carbon fines capture. With the above in mind, a series of tests were conducted to investigate standardizing simple laboratory methods for testing carbon quality. A standard procedure beyond or enhancing ASTM methods can serve as additional starting points for evaluating carbon specific to the gold industry. The investigation focused on size distribution, flatness, wet attrition resistance, surface area, gold kinetics, and gold loading. The final results provided information to generate an equation for ranking carbon samples to plant performance.IntroductionActivated carbon for use in gold extraction is amongst the most commonly found processes in modern gold-milling plants. Although gold losses are inevitable in the milling process, operators often focus on the importance of maximizing gold recovery. One focus area that is important in gold recovery is optimizing the use of activated carbon and examining potential changes to realize improved economics for carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes."

Jan 1, 2017

Compagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation. Tailings are stored in a ?fine? pond. Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and rainforest meteorological conditions). It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility. Therefore, CME asked Caspeo to: ? Carry out an on-site flotation pilot campaign. ? Design an industrial flotation circuit. The tailings reprocessing will contribute to a better tailings management and a dry up of the gold resource, limiting the risk of illegal mining after remediation of the CME site. CME MINE The Esperance gold mine is located in French Guyana, in the vicinity of several gold deposits as Omaï, Rosebel or Camp Caïman, holded by Iamgold and Newmont. These main gold deposits are located on the figure 1. Esperance was put into operation in the early 90?s. The first years were devoted to the mining of alluvial gold in the gravel of the Esperance Creek. Since then, operation was led in the primary gold deposit. Annual production is on average 254kg for a total production in fifteen years of 4300kg. Geology Esperance deposit is located in the greenstone belt of the Guyana Shield. Mineralization is in tectonic contact between sedimentary basin of Maroni and a granitic massif. Clastic series, composed of conglomerate and lamina sandstone, overlie a volcano-sedimentary basement (series called "Paramaca"). The area is strongly folded by shear movements, resulting from granite deposit. Gold is in interlacing quartz veins intersecting the clastic series. Gold is present in association with pyrite. Other elements, as silver or arsenic, are in negligible quantity. Exploitation The Maroni River is the only access to the Esperance mine. Only the saprolite and a part of the transition rock are extracted in the open pit. Excavation works are done using shovels Hyundai 450 (4 units) and haulage works using articulated dumpers Terex TA35 (4 units). These two sorts of equipments are presented figure 2. Mill The mill is composed of crushing and grinding processing plants. After gravity concentration, both plants produce tailings that are stored in two ponds: the first pond contains coarse product which segregates the particles crushed to 2mm upstream and settled clays downstream; the second pond contains the fine product made of particles ground to 200µm. These two ponds, bordered by dams and diversion canals, are located on former alluvial sites of Esperance Creek (see figure 3). [ ] The CME mill is currently producing gold concentrate, with a global recovery of about 67%. The ore is crushed by one jaw crusher and two hammer crushers. The ore then passes through a Knelson KC 48 gravity concentrator, producing a first gold concentrate. The

Jan 1, 2009

By Z. Botha

Sheryl Sandberg, the COO of Facebook, published a book titled 'Lean In', where she invites women to sit at the table. In summary, to 'sit at the table' entails not only embracing opportunity, but to actively seek out opportunities in leadership positions. Sandberg points out that, unfortunately, apart from institutional obstacles, a woman's own perceived limitations have a negative impact on her leadership ambitions. To create an environment where diversity will flourish, where everyone has a seat at the table and everyone has a voice, safety must be established first. To establish safety within a diverse team, there is power in relationships and connections. This study will first and foremost review theories in literature as to why diversity and inclusion are so important and the value that diversity brings to our industry. The study also recommends a few focus areas for improving diversity and inclusion in the industry.

Sep 1, 2022

By Alvin Kaufman

Following the gold discoveries of the late 1800's much was written regarding the vast mineral resources of Alaska, and much interest was aroused, and yet over the years little has been done to exploit those resources. Between 1906 and 1935 the Kennecott copper mines of the Copper River region were the keystone of the mineral economy (fig, 1). After the depletion of the Kennecott ore reserves and aided by the statutory rise in the price of gold, the yellow metal became the major mineral commodity. In recent years it has shared the honors with coal and sand and gravel. Although this trend should indicate the development of a stable, diversified mineral industry, yet the trend of production is downward. This report results from a study by the Federal Bureau of Mines to delineate the problems and to forecast the growth of the mineral industries in Alaska. The need for such a blueprint for the future was enhanced by the population explosion in the United States and the consequent eventual need for additional living space, as well as the current interest in new areas, and the necessity to develop reserves of strategic minerals.

Jan 1, 1961

By Peter J. Tarkoy

A great deal of attention has been directed toward the complexities and inadequacies of exploration and pre-bid geotechnical information for heavy construction projects, differing site conditions, and the adversary relationships which generally develop as a result. The adversary position has been maintained at all cost. The solution is simple, if not easy. The solution requires strict and equal adherence to given principles by all parties involved, throughout the life of the project, from conception to completion. It is necessary to review and redefine some basic concepts, without value judgements, from a context of getting the job done. In a recreated context, the role of truth, judgement, responsibility, and integrity, in exploration, engineering design, construction estimating, and project construction, will be examined. It is suggested that anticipated geotechnical conditions be defined unconditionally. The alternative choice is to give the bidder the opportunity of making the interpretive judgements based on geotechnical data. Similarly, a unilateral method of establishing encountered conditions that are agreeable to both owner and contractor, must be outlined prior to contracting. As anticipated and encountered conditions are firmly and accurately established, significant differences can evaluated based upon limitations specified in the contract documents. Impact of differences on project costs can be fixed by pre-defined methods.

Jan 1, 1983

By Sandra Lúcia de Moraes

O presente trabalho visou contribuir para o melhor entendimento do mecanismo inerente ao uso de agente coloidisante/dispersante no processo de pelotização de concentrado de minério de ferro. Avaliou-se a influência dos agentes coloidisantes em comparação aos aglomerantes Peridur e bentonita. Para este fim, foram realizados ensaios de bancada visando a identificação de possíveis ações destes agentes no grau de dispersão das misturas, bem como a sua influência na liberação/aglomeração dos finos. Os resultados destes parâmetros foram confrontados com os resultados de caracterização das pelotas confeccionadas com os diferentes agentes pelos quais foi possível identificar que os dispersantes tem forte atuação sobre o conteúdo de finos do concentrado de minério de ferro. A ação principal se dá pela remoção das partículas ultrafinas que recobrem os grãos mais grosseiros presentes na amostra e as dispersam, no caso dos dispersantes, aumentando a disponibilidade do conteúdo de finos <4 µm, principalmente os finos <1 µm (coloides). No caso do aglomerante orgânico, observa-se também essa ação, no entanto, os finos presentes são aglomerados na faixa entre 26 e 4 µm.

Aug 16, 2017

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By J. S. Brock

Magnetic, electromagnetic and gravimetric surveys have played an important role in the mineral exploration leading to the discovery of three major massive sulphide deposits in the Anvil-Vangorda area of the Yukon Territory. During 1964 and 1965 a saturation prospecting program, relying heavily on the integrated use of airborne and ground geophysical survey techniques, led to the discovery of the Faro deposit, which was subsequently proven to be a 63-millionton lead-zinc orebody. Locating the Faro deposit, the largest found to date in this overburden-covered region, involved an exploration sequence requiring the selection of a favourable geologic environment, aeromagnetic and electromagnetic surveys, property acquisition of anomalous areas and detailed ground geophysical surveys, followed by rotary drill testing, detailed gravimetric surveys and diamond core drilling.

Jan 1, 1973

By Mary Ellen Bruce Large

"In partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects.The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By Mary Ellen Bruce Large

"INTRODUCTIONIn partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects. The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

THE method depends upon:--1. The position of the mill.2. The space available for stacking the residue.3. The nature of the residue as discharged from the mill.4. The value of the residue for re-treatment.5. The requirement of the residue for underground filling.Originally the conditions in this district varied mainly in the position of the mill, some mills having an elevated site with plenty of dumping space for the time being, whilst others had a flat site, and very little dumping space near at hand; but in most cases the residue discharged was in the form of filter-press cakes, suitable for conveying on belts, or in trucks, and stacking in a high clump; and, while a portion of the residue was used for underground filling, the dump was regarded as a valuable asset, to be re-treated later. Under these conditions, conveyor belts, electric trams, aerial trams, and hose trucks, all gave satisfactory results, and the following figures, taken from "'West Australian Metallurgical Practice," will show how these methods compared as regards costs...

Jan 1, 1909

By Peter White

Mine Planning Shaft Collar Shaft Sinking Raises Ramp Underground Water Storage

May 1, 2009

By John J. Mulligan

The creeks draining Cape Mountain, on the western tip of Seward Peninsula, Alaska, comprise the Cape Mountain tin-placer district. Because of the war-caused shortage of tin, the Bureau of Mines in 1943 conducted a churn-drill placer reconnaissance to explore the district. Favorable indications were found, and plans were made for further investigation of the deposits; the plans were abandoned when tin again became plentiful. In July 1951 the Zenda Gold Mining Co. was granted a Defense Minerals Administration (Defense Minerals Exploration Administration after October 1951) loan to continue exploration of the more favorable areas indicated by results of the Bureau's investigation. Equipment was moved to the area in the fall and winter of 1951-52. During the 1952 field season, 209 churn-drill holes totaling 7,521 linear feet and 10 test shafts totaling 96 linear feet were sunk on the Cape Creek drainage. Work was resumed in 1953, when 56 churn-drill holes totaling 3,157 linear feet were drilled on Boulder Creek. The company planned to drill Goodwin Gulch and Goodwin Creek, but no further work was done owing to lack of capital.

Jan 1, 1959

By Wilson Blake

Increased application and interest in the use of microseismic monitoring to deal with ground control problems, Particularly those resulting in violent failures, has brought about the need for practical guidelines with respect to all phases of microseismic monitoring. This report presents the results of an 18-month effort to review the microseismic method and develop needed practical guidelines. Microseismic activity and properties of microseismic events are treated so that these parameters can be taken into account when developing monitoring equipment. Microseismic equipment is discussed to provide familiarization with the components of monitoring systems. Factors to be considered and procedures for developing a microseismic monitoring system are presented. Both physical and electrical considerations for the installation of a monitoring system are discussed in detail. The operation of a microseismic system including data analysis procedures is presented. Field examples to illustrate use of microseismic data in evaluating ground control problems are presented in a number of case histories.

Jan 1, 1982

By David Whalen

Mobile equipment in oil sand mining operations experience more maintenance problems than similar equipment in other surface mines, due to soft underfoot conditions. Oil sand properties are known to vary with temperature, bitumen content and previous loading cycles. One of the challenges is the widely variable underfoot pressure which supports shovels and trucks. In the case of a heavy hauler driving on in-pit roads, each tire is supported by a different ground stiffness resulting in an apparent uneven surface. Driving over uneven ground causes twist in the truck frame, which is transmitted to the dump body. Through a finite element analysis of a haul truck dump body, it was shown that slight frame twists produce localized stresses in the intersections of the floor stiffeners. These stresses are at times greater than those resulting from the maximum ore weight and are primarily responsible for cracking in these intersections. Syncrude maintains high quality haul roads, which are constructed of gravel, and makes every effort to keep the shovel pit roads as smooth as possible. This problem cannot be avoided through operational practices only and must also be accounted for in the design of haul truck bodies.

May 1, 2003

This report describes the development of training materials for the operators of underground mining equipment in the underground metal and nonmetal mining industry. The objective was to determine the effectiveness and acceptability of these training materials and to provide the validated training materials to the industry. Ten modules were developed, based on industry need according to accident frequency, accident severity and exposure to the equipment. The final modules were an average of 20 minutes in length and used slides with synchronized narration on cassette tapes. Testing materials are included for use by the mines.

Jan 1, 1984

Drilling and blasting are an essential part of most mining operations, and are commonly major operating cost centres. The effectiveness of blasting can have a significant influence on all subsequent activities, and hence overall operating costs. Drilling and blasting systems must be compatible with the overall mining method, to minimise total costs and ensure operational efficiency. Selection of suitable equipment and techniques requires an understanding of the total operation, plus current skills in specialised technologies. This paper examines the contribution of drilling and blasting to total costs, including the balance between capital and operating costs. The use of computer modelling is discussed, to demonstrate how blast performance and costs can be predicted and alternatives analysed. Case studies illustrate how cost savings can be made in operating mines, and alternative systems evaluated to optimise new projects.

Jan 1, 1990

By Manis Kumar Jha, D. D. Pathak, Archana Kumari

Treatment of secondary/waste to recover rare earth metals (REMs) is gaining importance due to its increasing global demand, lack of availability of high grade natural resources and huge generation of secondaries. Present paper reports the critical review on available processes for recovery of REMs from secondaries viz. manufacturing scraps, e-waste, industrial residues such as red mud, fly ash, waste water, etc. Hydrometallurgical processes with combination of Beneficiation/ Pyro-/Electro techniques are discussed to recover REMs effectively. The recommended processes require less energy to deliver high purity yield which is one step towards green environment. Salient findings on various methods are reported with recommendations which will be helpful to researchers working in the area of REMs extraction.

Mar 1, 2018