Search Documents

By Shengli Yang

Solid backfill mining, as a green mining technology, has the advantages of a higher resource recovery, less damage to the environment and the ability to dispose of waste underground. It has been applied successfully in the Xingtai and Xinwen mining areas in China. Strata behavior and the movement of overburden strata in this mining method are very different from fully mechanized longwall mining, which results in a natural caving, because the gob is filled with waste rock, fly ash and other backfill material. The results of field measurements showed that the periodic weighting interval of the main roof is longer; the magnitude of periodic weighting is smaller; the peak and zone of influence of the front abutment pressure are smaller than those in fully mechanized mining; that major deformation of mine roadways occurs within the influence zones of the abutment pressures; that the falling space of immediate roof is smaller, with the lower portion falling more sufficiently than the upper; that the main roof subsides slowly; and that the falling height of the overlying strata is greatly reduced.

Jan 1, 2011

By A. G. Pasamehmetoglu

The swelling process is an important problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from pedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the pedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

By E. H. R. Schumann

The local stratigraphy and composition of the coal measures, including competent dolerite sill and massive sandstone lavers is shown to have a restricting influence on the development and magnitude of surface subsidence above total extraction panels in South Africa. The critical panel width necessary to induce nonviolent failure of a dolerite sill is quantified. Small subsidence due to the deflection of a 70 metre thick dolerite above subcritical panels is shown by example. Maximum surface subsidence tilt an; ground strain is compared to the NCB model. An exponential subsidence profile curve, SPC, describes a trough half-profile. A parabolic relationship between horizontal displacement and tilt, which has been discovered to exist can be substituted in the first derivative of the SPC in order to generate transverse displacement and strain profiles.

Jan 1, 1988

By Zhaohui Wang, Jiachen Wang

"Effective surrounding rock control is a prerequisite for realizing safe mining in underground longwall faces. In the past three decades, longwall top-coal caving mining (LTCC) and single pass large height longwall mining (SPLL) found expanded usage in extracting thick coal seams in China. The two mining methods lead to large void space left behind the working face, which increase the difficulty of ground control. Longwall face failure is a common problem in underground mining, which is induced due to low strength and high fracture density of the coal seam. Moreover, the stiffness of main components included in the surrounding rock system also greatly influences longwall face instability. Correspondingly, the surrounding rock system is developed for LTCC and SPLL faces in this paper. Mechanical conditions for simultaneous balance of roof structure and longwall face are put forward by taking the stiffness of coal seam, roof strata, and hydraulic support into account. The safety factor of the longwall face is defined as the ratio between its ultimate bearing capacity and the load imposed on it. The influence of coal strength, stiffness of the coal seam, roof strata, and hydraulic support, as well as the movement of roof structure, are analyzed. Finally, the key elements dominating longwall face stability are identified for improving surrounding rock control effectiveness in LTCC and SPLL faces.INTRODUCTIONThe concentration of coal mining in China is gradually shifting to the west region, and there are a large number of thick coal seams in the newly formed coal mining area. Therefore, the surrounding rock control problems related to mining of thick coal seams will become the focus of research in the field of mining engineering in the future. There are two kinds of mining methods for thick coal seams in China, including single pass large height longwall mining (SPLL) and longwall top-coal caving mining (LTCC). Both methods can accomplish the goal of excavating the full thickness of thick coal seams at one time. SPLL mining benefits from the improvement of the development level of associated equipment. The appearance of large hydraulic supports and high power shearers ensure that the height protected by the hydraulic supports and the height of the sheared coal are the same as the coal thickness. LTCC mining benefits from mining technology advantages. The thick coal seam is divided into two sub-layers, and the working face is normally installed in the bottom layer, while the top coal is caved under the compressive forces due to mining. Therefore, there is a scraper conveyor at the front of the hydraulic support for transporting the sheared coal and another one at the tail for transporting caved top coal. Both SPLL and LTCC methods realize one-off recovery of thick coal seams."

Jan 1, 2018

By Sun Henghu

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed. The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by excess water drainage under the ground are resolved.

Jan 1, 1992

By Christopher Mark

Despite more than half a century of experience with roof bolting, no design method has received wide acceptance. To begin to improve this situation, National Institute for Occupational Safety and Health (NIOSH) conducted a statistical study of roof bolt performance at a number of mines throughout the U.S. Case histories were collected from 37 mines with a variety of roof bolt types and patterns in a wide range of geologic environments. Performance was measured in terms of the number of roof falls that occurred per 10,000 ft of drivage. The study found that roof falls are rare when the roof is strong and the stress is low, even with light roof bolting patterns. The focus of this paper is on the more difficult conditions, where the roof is weaker and/or the stress is higher. Analysis of the results led to guidelines that can be used to make preliminary estimates of the required bolt length, capacity, and pattern. The guidelines are based on the depth of cover (which correlates with stress) and the roof quality (measured by the Coal Mine Roof Rating (CMRR), and the intersection span. Another contribution is a formula for estimating the horizontal stress level in the eastern U.S. coalfields as a function of the depth of cover. The design guidelines are currently being implemented into a computer program called Analysis of Roof Bolt Systems (ARBS).

Jan 1, 2001

By George S. Kalamaras

Coal strata strength is included as a vague term in most of the pillar design formulas, either as a questionable fraction of the intact coal strength or a size-dependent relationship for scaling down a laboratory value to the in situ strength. In order to introduce a coal mass strength criterion which would be compatible with current design trends, the Rock Mass Rating (RMR) system was revised to incorporate factors governing coal seam behavior under load. A number of adjustment factors have been proposed but, the most significant change, is the introduction of a parameter representing the heterogeneity of the seam. When developing a rock mass strength criterion, it is necessary to find the constants of appropriate intact rock strength criteria and to establish a correlation to scale down these constants as a function of the RMR. For four intact rock strength criteria, the constants for coal were found using the Nelder-Mead method. To correlate the constants of the strength criteria with the coal seam quality values (RMR), a procedure was developed based on finite element modeling of in situ large scale tests for which the RMR was known. A new coal strata strength criterion is proposed, in a principal stress formulation, for modeling coal pillar behavior when the stress field in a pillar is known. A linear relationship is also given, to be used when empirical pillar strength formulas are used to design pillars. The proposed criteria have been evaluated in a case study.

Jan 1, 1993

By Ross W. Seedsman

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By Chris Mark

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends, If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the "full resistance zone" of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. This paper describes recent studies using short encapsulation pull tests in the U.S. Tests were conducted in the National Institute for Occupational Safety and Health (NIOSH) Safety Research Coal Mine at Bruceton and at underground mines in Pennsylvania and West Virginia. The study found that the SEPT can be used to make a simple evaluation of resin bolt anchorage. Suggested procedures for conducting SEPT are included. The study also confirmed that poor anchorage can be an issue, particularly where the roof rock is very weak. Some simple techniques for improving anchorage, and thereby the effectiveness of fully grouted bolts, are discussed.

Jan 1, 2002

By Zhanjing Yu

In this paper, an equation is developed to characterize the relationship between the UBC and plate size using a boundary integral approach. The equation was validated by the results from mo& than seventy (70) plate loading tests of different sizes conducted in various underground coal mines throughout the Illinois Coal Basin. The equation indicates that the UBC decreases as the plate size increases. The fundamental solution for this boundary integral problems is the Boussinesq equation. The load exerted by the plate on the floor surface is assumed to be uniformly distributed. Both normal and tangential loads are considered. It is also assumed that the floor fails in shear in a plate loading test. The equation may provide the mine operators with a useful tool to obtain from a plate load test of any plate size the UBC value required by the regulations.

Jan 1, 1993

By James Arthur

In deep coal mining the support of the underground roadway is fundamental and without knowledge of the mechanics of ground control a mine is unlikely to be operating safely and efficiently. It is therefore important for the support system to be designed sat¬isfactorily for the size of the excavation required and to do so an understanding of the behaviour of the surrounding strata is re¬quired. Over the last 15 years there has been a major change in the industry and the support systems adopted. The industry has been privatised, legislation has been updated, a comprehensive research programme has been carried out and guidance docu¬ments produced. The paper will show how privatisation has not allowed support standards to deteriorate, highlight research, the legislation and guidance documents updated and how this has led to a reduction in accidents and falls of ground..

Jan 1, 2002

By André C. Zingano

The domino effect in a violent pillar collapse occurs due to the redistribution of stress in the remaining pillars near the collapse, and this stress transfer occurs in the immediate and main roofs. The remaining pillars do not have enough load capacity to support this overstress and also fail, and the domino effect propagates further to the entire panel. The domino effect does not occur only due to low load capacity of the pillars, but also the roof rock mass quality, because the stress is transferred by the roof. In high competent roof without discontinuity (fault), like massive sandstone seam, the deformation of the roof is the cause of pillar collapse extension and propagation. Depending on how close it is approaching the collapse limit; the immediate and main roofs behave differently. When it is close to the collapse limit roof convergence and pillars compression occur. Conversely when it is far from the collapse limit divergence and pillars decompression occur. This is called the arc-effect. This paper studies this behavior of the roof (immediate and main roofs) using numerical modeling to simulate the roof deformation and stress distribution in the roof and pillars. This simulation represents the progression of pillar collapse and shows the zone of convergence and divergence of the roof, and also the effect of this behavior on pillar confinement. Two-dimensional plain strain model was applied to simulate the arc-effect. The simulation results were compared to those of the instrumentation that was installed before the collapse. Keywords: pillar collapse, room and pillar, numerical modeling

Jan 1, 2005

By Stephen C. Tadolini

A new innovation in coal mine roof support has been developed by the Bureau of Mines at the Denver Research Center. The technique, called "Thrust Bolting,"1 converts a traditional passive roof support system, a full or partial column rebar bolt, into an active support system by following a specific installation process. The thrust bolting system provides two advantages from a ground control standpoint. First, because the system is active, no roof movement is necessary to put the bolt into tension. This eliminates the possibility of strata separations in sedimentary roots, minimizing progressive-type roof failures. Secondly, the tension placed on the system is independent of mechanical devices or torques. This eliminates the highly variable frictional losses that occur between the bearing plate and the bolt head and in the threaded portions of traditional active support systems. These two improvements create a safer working environment for mining personnel. An additional advantage of this improved support system is the reduced cost of installation and maintenance. The initial support cost is reduced by a minimum of 30 percent per bolt when compared to similar conventional support systems. The labor intensive and potentially hazardous torque¬tension test, required for most tensionable active support systems, is not required for thrust bolts. The potential for improved support performance and cost reduction of thrust bolting has generated a considerable amount of interest from both industry and MSHA. This paper will describe, in detail, the theory and application of thrust bolting and present the results of two underground coal mine case studies.

Jan 1, 1990

By Vladimir Adamek

Two existing predictive methods were chosen for evaluation; an influence function (Gals Theory) and a profile function (hyperbolic). These were applied to several field measured subsidence pro¬files over United States coal mines. The effect of homogeneous versus non-homogeneous overburden on surface subsidence is demonstrated and the utilization of Bals Theory as a subsidence predictive method for both types of overburden is examined. The major factor affecting subsidence profile characteristics is the migration of the inflection point toward the centerline of the longwall panel. A computer program was written to aid in the analysis.

Jan 1, 1981

By Michael J. Friedel

The fundamental problems associated with ground control reflect the inability of mining personnel to "see" the development of anomalous conditions. Toward this end, the U. S. Bureau of Mines is investigating the application of seismic refraction tomography for imaging the process of pillar yielding, at the Foidel Creek coal mine, near Steamboat Springs, CO. The inherent three-dimensional problem of imaging coal pillar stress is reduced to a single plane by considering only the stress transmitted from the pillar to the adjacent floor rock. This approach exploits the fact that refracted seismic energy is essentially confined to the adjacent higher velocity sandstone strata. The tomographic analysis using ray-tracing based on wavefront migration resulted in a robust P-wave tomogram from which regions of high velocity indicate zones of high stress concentration, whereas low velocity zones indicate regions of stress relief. The interpreted region of high stress concentration occurs at the pillar end nearest to the working face of the adjacent longwall panel. This finding is corroborated by vertical pressure cell measurements recorded in the pillar. The stress diminishes toward the pillar perimeter with local minima correlating to the locations of observed pillar spalling. Time-sequence monitoring, as the longwall face advances, is recommended for evaluating changing stress conditions.

Jan 1, 1993

By Thomas M. Baraak

This paper evaluates factors which influence longwall support and strata interaction. The longwall system is composed of an immediate and main roof structure and three supporting foundations: 1) longwall panel, 2) powered roof supports, and 3) gob waste. The main roof forms a structure that is generally supported by all three foundations, while the immediate roof acts as a beam that cantilevers from the coal face to the powered support. In most cases, shield loading involves a complex interaction of both main roof and immediate roof behavior and is a combination of loads produced from subsidence of the main roof and displacements of the immediate roof caused by deformations of the cantilevered roof beam. Since the shield stiffness remains constant for all leg pressures and main roof convergence is irresistible in terms of shield capacity, the shield must be able to control the behavior of the immediate roof or floor structure for shield loading to be sensitive to setting pressures. If the goal is to minimize total shield loading, any active setting force must be offset by reduced passive shield loading to justify the active setting loads. Field data suggest that the typical reductions in passive loading do not justify the required increases in setting pressure in some applications.

Jan 1, 1990

By Francis Kendorski

One of the most dangerous events in underground coal mining is unexpectedly encountering water inrushes from undetected abandoned mines in the same seam. The surest and most confident method is probe drilling either from the mine or from the surface. However, drilling is expensive and may even miss the suspected mine voids entirely by drilling through pillars. Many operators rely upon one or more of several remote sensing techniques for detecting mine voids. However, mine "voids" often are not air- or water-filled open cavities, but are collapsed, rubble-filled chimneyed columns in the strata. Geophysical techniques, such as seismic reflection and refraction, electrical resistivity, magnetics, ground-penetrating radar, and others, often assume a continuous or fractured rock mass that has varying properties which provide the signatures that allow discrimination of one strata from another, or of strata from voids. However, a rubble-filled cavity has rock block-to-rock block contact throughout its volume and can still respond as a continuous rock mass with the rock blocks allowing signal transmission or mass detection, rather than a void space. Hydraulically, a rubble-filled cavity is essentially as transmissive to water as an open mine void. Thus, the problem of detecting a mine void with confidence is significantly compounded.

Jan 1, 2004

By John Kucish

Roof bolting in the Pittsburgh Coalbed takes many forms today: coupled partially grouted bolts, fully grouted rebar, passive cable bolts, tensioned cable bolts, and torque tension rebar. The Federal No. 2 Mine of Peabody Energy has recently made a significant advance in longwall headgate primary roof support, with the change fiom an 8 ft long coupled partially grouted bolt to a 6 ft long torque tension system. The coupled partially grouted bolt consists of a 4 ft long 0.804 in diameter rolled deformation bar thread coupled to a smooth 718 in headed bar. The coupled partially grouted bolt is anchored into a 1 318 in borehole with 4 ft of high speed resin. The 718 in diameter smooth bar is tensioned by rotation into the treaded coupler, upon setting of the resin, compressing the immediate roof. The change was initially driven by occasional failure of the coupled partially grouted bolt at the threaded coupler, due to lateral movement caused by horizontal stress. A fully grouted % in diameter torque tension bolt, in a 1 in borehole, was proposed as a cost effective primary bolting for the high horizontal stress conditions. The upper 2 112 ft of the rebar is anchored in fast set, medium viscosity resin and the bottom 3 K ft is anchored in slow set, special low insertion force resin. The lower end of the rebar is threaded with a nut that permits the counter clockwise spinning of the bolt to mix the resin, at maximum rotational torque. Upon setting of the high speed top resin, the nut is spun clockwise to tighten the nut against a metal dome plate. The plate is forced against the roof to compress the immediate roof, A complete headgate entry has been successfully supported with the torque tension system. The mining of the adjacent longwall panel was completed in September 2004. The torque tension system provided a 25% savings over the previously employed coupled partially grouted bolt system.

Jan 1, 2005

By Vladimir I. Klishin

Complex method of ruling of rock pressure is considered in conditions of rapid roof subsidence. The purpose of this method is elaboration of emergency devices into hydraulic props. Also method of unloading of solid roofs is worked out. An analysis of means of protecting hydraulic props of powered supports 6om dynamic loads made it possible to divide them into four classes according to principle of operation: emergency, operating hm an increase of pressure; emergency damping; emergency, operating according to the "plastic element" principle; inertial emergency, operating hm dynarmc loads. It was established that the overwhelming 'majority of designs of the first three classes of emergency devices (EDs) are based on !mditional approaches, which exhausted their possibiiities of high-speed response. Delay on their opening is caused mainly by inertia of the moving locking parts. In our opinion, the most prospective are EDs using the inertia of the moving locking parts for depressurizing the piston cavity of the hydraulic prop with a minimum delay (inertial EDs). The essence of the designs of EDs having an inertial principle of action is that into the hydraulic prop containing movable and immovable elements is additionally introduced a spring-operated contracting support, which is installed on the movable element. Under dynamic loading of such a hydraulic prop hm the roof, the support moves relative to the movable element, performing the role of an inertial mass, which leads to instantaneous depresswization of the piston cavity of the hydraulic prop. Technological measures for unloading of solid roofs consists in creating of long oriented cracks in rock massif. Description of method for creating cracks, demanding equipment and means for cone01 the progress of splits are included. Also technological schemes for realization of the method of saving underground mines and rock mass are included. The results of experimental realization of this method on the Kuzbass and Poland coal mines are also included.

Jan 1, 1997

By C. Tom Blevins

The purpose of this paper is to discuss production and roof control problems associated with directional lateral stresses in an in situ stress field and the approach that Inland Steel Coal Company made in trying to cope with them. Before proceeding, a description of the mine location, product, geology, restraints, and mine history is in order. The mine is located in Hamilton County in Southeastern Illinois. It produces a high volatile metalurgical coal and is slated to produce 2.1 MTY. Product ion is in the Illinois No. 5 seam at a depth of 930 feet, approximately 490 feet below sea level. The scam height averages from 5.5 to 6.0 feet throughout the reserves with height increasing in the eastern reserve area to approximately feet and a 5 Foot average in the West. The scam tends to dip to the North, North East, but is locally very undulating. The Galatia channel washout outlines the eastern boundary of the reserves and there is a split coal area toward the central part of the property than runs south-southeast. The top above the #5 seam is laminated medium gray shale called Dykersburg. Individual shale bedding planes vary locally From ½ to 1" in thickness to a more normal thickness of 1 to 1 ½ with some areas being interlayed by thin carboncous material. The top normally must be considered as materially competent. Even though the mine is still relatively small in area with only 1.3 million tons of total production to (late, we have encountered dense zones of slicker sides and premining, stress cracks (joints). There are also areas of siltstone, that vary from a few inches to several feet thick, and areas of rider coal, clay instrusions, and rolls. We have crossed lineament concentrations that show strong evidence of corelation to localise top problems. These are being monitored closely to see their predictability on our present and future mining conditions. The face cleat runs N 55° E and butt cleat runs S. 25° E. On a regional basis, there are several anticlinal belts that trend in a northerly direction. The one major restraint is that Inland does not own surface subsidence rights. Therefore, a partial extraction mining plan is being followed. The Holland-Gaddy formula for pillar strength design is used to calculate theortical pillar sides. When production began in March of 1979, it was noted that ground control problems occurred as we drove north entries. East-west cross cuts tended to have better working conditions. This phenomia occurred from a couple hundred feet, but seemed to dispate as we got away from the men and material shafts. Once the production shaft was connected and enough entries extended for installation of belts, ground control problems were again experienced in north-south headings. It was also observed that when mining north-south headings with east-west crosscuts, if the crosscut was driven through ahead and supported, the intersection was stable upon entry connection. This held true even where fairly extreme ground control, problems were encountered. The reverse held true. when driving east-west headings with north-south crosscuts. At this time, we started searching in earnest for a working theory to explain this roof phenomia. It also became the first step of what eventually was a four step sequence to derive a workable solu¬tion to the problem. The combination of the many geological changes and the fact that north-south condition was at times intermitent, helped to disguise the stress field. The mine also being in a fairly virgin area with no mines in approximately 25 milt, radius, meant we didn't have a reliable case history to examine. Various theories were researched before it was concluded that our primary ground control problem was a directional lateral stress Field, with the major stress axis in an east-west direction. The second stop of the procedure was then to test. mining methods and determine if these stresses could be modified to a

Jan 1, 1982