Search Documents

"When boring a tunnel, homogeneous hard rock is the exception rather than the rule. While contractors can set goals such as meters per month and performance incentives, it is also prudent to plan for difficult ground. A properly designed tunnel boring machine (TBM) can tackle fault zones, water inflows, squeezing ground, or whatever the risk may be. The alternative is not a good one: modifying the machine in the tunnel after bad ground is encountered. Not only does this result in increased downtime, but it also needlessly exposes the crew to the tunnel conditions. In the worst case scenario, the entire operation grinds to a halt.However, an accurate GBR cannot always be obtained, particularly for mountainous, high cover tunnels in remote locations. And even with a thorough GBR, unforeseen geological events can occur. What can be done in these situations? Difficult Ground Solutions (DGS) is ground investigation system with a suite of options that can be added to a shielded hard rock machine or dual-mode, Crossover machine to better enable advance when conditions are unknown or difficult conditions are anticipated.DGS consists of a set of integrated features tailored to a specific project’s geology. The main components of the system allow for ground investigation ahead of the TBM, increased monitoring and methods to keep a machine shield from becoming stuck.In fault zones and squeezing groundIf fault zones or squeezing ground are known or suspected, or if there is even a possibility of encountering them, this can greatly affect the TBM operation. Shielded machines protect the crew from the surrounding rock, and they can bore and line a tunnel efficiently, but in fault zones and converging material their shields can be their downfall. Avoiding a stuck machine is paramount to project success. DGS employs several features to avoid the problem of a machine becoming stuck. The first of these is multi-speed cutterhead drives. These drives effectively give the machine multiple modes of operation—high speed, low torque for hard rock, and low speed, high torque for difficult ground. Designing a machine with high-torque, continuous boring capabilities allows that machine’s cutterhead to restart with break-out torque in difficult ground. The net effect is that the machine can keep boring in the event of a face collapse and can bore through fault zones and running ground where the potential for cutterhead jamming exists. Going one step further, multi-speed gearboxes give the machine the ideal earth pressure balance- (EPB-) type torque if larger sections of soft ground are anticipated.Secondly, TBMs can get through squeezing ground and faults using Continuous Shield Advance. This design utilizes a stepped shield configuration — where each successive shield is slightly smaller in diameter — to avoid becoming stuck in converging ground. External shield lubrication is an added insurance against becoming stuck, using a series of radial ports that can pump Bentonite into the annular space to act as a lubricant in squeezing material.As a last effort, if a machine has already become stuck the TBM can utilize augmented, or “super” thrust. Additional thrust jacks can be added to supply an extra boost in a short stroke, generating enough force to break loose a trapped shield."

Jan 12, 2017

By Daniel W. Kappes

The 1.8 million tonne Itos tailings deposit is the result of sever­al years of processing by Comibol of the San Jose and ltos Mine ores at Oruro Bolivia. The historic flowsheet consisted of a flotation circuit in which silver-bearing galena and stibnite were concentrated. Approximately half the silver in the ore was not recovered, and the existing tailings contain slightly over 200 grams silver per tonne, in the form of complex sulfides of silver, antimony, lead, and other metals coating grains of pyrite. An extensive laboratory program was conducted to exam­ine conventional processing l)lethods such as cyanide leaching and regrinding followed by flotation. However, the silver-bear­ing sulfides are in intimate contact with the pyrite and the pyrite comprises 30% of the total tailings weight. Cyanide leaching recovers only 40% of the silver and the cyanide consumption is uneconomically high. Flotation produces an upgraded, but still uneconomic, concentrate. For this reason, chloride leaching had been evaluated by Comibol, and in the mid 1980's Comibol undertook an innova­tive test consisting of two 300 tonne field heap leaches using a cold chloride solution. The tests were partially successful, but could not be applied to the bulk of the tailings which are already ground to 50% minus 200 mesh. In 1992, Kappes, Cassiday & Associates undertook to develop a hot agitated chloride leach flowsheet, and is current­ly constructing a treatment plant under a turnkey contract from a Bolivian company, Baremsa, S.A. Using this process, 85% of the remaining silver can be recovered, with significant by-prod­uct credits from antimony and lead. The project features hot, agitated acidic chloride leaching, filtration, crystallization of lead chloride, and precipitation of metals using iron scrap. Arsenic is removed from the precipitate by caustic leaching, and minor metals by furnace refining. Antimony is recovered as the oxide by cupelation, and silver is poured as <lore from the cupel. Production rate will be 600 tonnes per day. Startup is scheduled for late 1995.

Jan 1, 1996

By S. Chander

A mineral or metallurgical process uses various inputs, such as ores, energy and other raw materials, to make different products that fulfill societal needs. The processing of raw materials has changed in recent years due to the increased complexity of processing low-grade ores, intensifying competitiveness and greater constraints. For process improvement, various plant optimization and process modifications must be conducted under environmental, social, political and economic constraints. Processing research and education&apos;s success in meeting the process industry&apos;s future needs depends on an adequate balance between micro- and macro-engineering approaches. In its simplest form, macro-engineering is concerned with the "big picture," while micro-engineering requires looking at a subset of the process. So macro-engineering may be defined as an investigation of the larger or "whole" system to achieve the desired goals. And micro-engineering may be viewed as a quantitative investigation of a subset of the process, to determine cause-and-effect relationships within the subset. Two different approaches might be used in macro-engineering analysis. In one, the big picture may be viewed without a detailed knowledge of the subunits. With this approach, statistical tools are used to relate input and output parameters. Also, actual plant data or analog models might be used to obtain the desired information. The usefulness of such an approach increases with problem complexity. To attain the desired goals using the second, "model-based," approach, a detailed knowledge of the subunits is often useful and their interactions may be considered. In complex process analysis, the first of these approaches is more useful since less information is needed. However, it is also less exact and more likely to fail if there are significant changes in conditions and interactions. The second approach, on the other hand, is more exact, with greater predictive ability within the narrow subset being considered. Consequently, it is difficult and costly to conduct.

Jan 1, 1992

By Garrett R. Hyde, Aleksandar Stojsic

Introduction Economic pressures in the international marketplace have spurred advances in almost every facet of flotation. New developments have occurred in flotation chemicals, flotation machines, and in the application of automated process control technology to grinding and flotation. Many of these advances are the results of concerted efforts to apply the knowledge obtained from basic flotation research over the past 15 to 20 years, to develop industrial technology for the more efficient separation of sulfide minerals in real ores. Mining company executives and equipment manufacturers are being called on to make decisions for incorporating some of this technology into present operations. This discussion is limited to two developments now at the stage of being engineered into industrial scale operations. They are control of the electrochemical environment or redox potential of the slurry, and control of bubble size in column flotation. Potential economic impacts are noted. Froth flotation Froth flotation makes use of differences in the surface properties of finely ground minerals to obtain separation. If the mineral surface is water repellent, the mineral particle will stick at the air-water interface of a bubble and float. If a mineral surface is not naturally water repellent, a chemical collector is added to the slurry to make it so. The collector must adsorb on, and make water repellent only the mineral to be recovered, not the gangue minerals. To achieve this degree of selective adsorption, chemical modifiers may have to be added to the slurry. Modifiers include pH regulators, activators, and depressants. Electrochemical control One of the most significant developments in recent years in the area of mineral processing technology is the recognition that collector adsorption of sulfide minerals is an electrochemical process. Consequently, flotation of these minerals depends on the electrochemical or redox potential of the system. Many of the modifiers used to control various flotation processes are actually potential controlling reagents. For example, the role of well known depressants, such as cyanide, sodium hydrosulfide, and sulfur dioxide, is essentially to

Jan 7, 1987

By J. S. Gardner, K. E. Houston, A. Campoli

INTRODUCTION Disposal of coal refuse is a costly and challenging problem facing the coal industry today. After the Martin County Coal Company slurry spill and the subsequent regulatory changes state and federal agencies are now beginning to require companies to justify new slurry impoundments. The authors have performed an analysis of different means of disposing of coal refuse for a major coal producing company located in the eastern Kentucky coalfields (the name of which will be withheld for the purpose of this paper). The company’s existing slurry impoundment is nearing its maximum permitted elevation and also an elevation where it may come in contact with abandoned underground workings. Due to the increased concern with underground mine works near slurry impoundments, additional consideration was given to raising the existing impoundment. Several other alternatives were evaluated, including but not limited to raising the existing impoundment, constructing a new slurry impoundment, constructing slurry cells, belt presses and others. This alternatives analysis was performed as part of a Section 404 permit for a valley fill and is currently being reviewed by the U. S. Army Corp of Engineers. All of the known possible alternatives were discussed in detail in the analysis. Due to the findings of the alternatives analysis, the company considers the engineered construction of the proposed impoundment to be the most favorable option of all the other alternatives evaluated, from both an economic and environmental standpoint. ALTERNATIVES EVALUATION FOR COALREFUSE/SLURRY DISPOSAL Background The company currently operates several deep mines and employ over 300 people and produces over 3.9 clean Mt/a (4 million stpy) of high quality, low sulfur coal. Currently, coarse refuse is belted to a valley fill, while, fine refuse is pumped to the existing impoundment. Coarse refuse is trucked to the existing impoundment as needed for construction purposes. The average recovery is approximately 50%; therefore, over 3.9 Mt/a (4 million stpy) of coal refuse must also be separated and placed.

Jan 1, 2003

By Eric Forssberg, Mats Hallin

INTRODUCTION Evaluation and optimization of mineral processes has been going on since the the first plant started hundreds of years ago. A huge mass of knowledge has been collected since then. The main problem with this type of empirical knowledge of complex processes is that it is very difficult to formulate and document. The methods used for collecting the knowledge is not consistent but-varies with "he person" that does it. In the late 60&apos;s and early 70&apos;s efforts were made to use computer based techniques to evaluate process performance and to formulate process models for mineral processes. Models were developed, such as the flotation model by R. P. King (1973) which is still used to simulate flotation circuit behaviour. During the 70&apos;s. a number of mass balancing packages were developed together with process simulation packages. The industrial sector also made great efforts to develop and utilize computer based systems for process control and evaluation. The expert system that BOLIDEN created in 1974 at the Kristineberg plant was a remarkable achievement considering the hardware (CDC 3600) and the software tools (FORTRAN) available at that time. The main obstacle to successfully implement optimizing computer control of mineral processes was and still is the limited knowledge about the dynamics of complex processes. There are, however. many activities going on in this area today and it seems that the technology is very near a break through. Process evaluation is the most important tool to improve and maintain the optimal performance of a process. Today dedicated computer based techniques are used for fast and reliable screening of the processes. The stages in process evaluation consist of three basic steps: - Data acquisition, manually or by data logging. - Data refining, mass balancing and parameter calculation. - Data evaluation. The refined data can then be used for model construction/calibration and subsequently for process simulation. This paper describes two studies where the techniques mentioned above are used to evaluate and simulate

Jan 1, 1991

By S. K. Kawatra, A. K. Bakshi

Mineral suspensions in water show Newtonian flow properties at low percent solids. However, this changes to a non-Newtonian regime as the pet-cent solids increases. For Newtonian fluids, viscosity is independent of shear rate, hut, for non-Newtonian fluids, viscosity varies with shear rate. Therefore, if the slurry is non-Newtonian, attempting to measure the viscosity at a shear rate different from the shear rate experienced by the fluid within the process is futile. This is especially true for a hydrocyclone, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between the viscosity and the process efficiency. A new technique to distinguish such changes inflow type was developed. This involves two viscometers: a coaxial cylinder-type viscometer that measures apparent viscosity at low shear rates and a vibrating sphere-type viscometer that measures the apparent viscosity at high shear rates. For each of these instruments, special precautions were taken to allow, for the measurement of the viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer is operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica (80% passing 65 µm) in water was used to prepare slurries at concentrations ranging from 10% to 70% (by weight) solids. The viscosity of each slurry sample was measured simultaneously by both viscometers, and the results were compared. With this technique, it was found that all of the silica-slurry samples tested were in the Newtonian flow regime for up to 70% (by weight) solids. Methocel and Cellosize polymer solutions showed clear non-Newtonian behavior using this technique. This confirmed that non-Newtonian behavior of the silica slurries, if present, would have been detected by this arrangement.

Jan 1, 1997

By Nicholas T. Camicia

A career in the coal mining industry today offers students one of the most interesting and challenging opportunities available in the industrialized world. As reserves of other fossil fuels dwindle in face of the world&apos;s demand for energy, it has become apparent that coal, once the king of energy sources, must be relied upon again as the major fuel for powering industrial growth in developed and developing nations. Centuries of coal supplies lie beneath the earth&apos;s surface, assuring the world of a steady, plentiful supply of energy until science and technology can produce a way to harness and efficiently use renewable sources, such as solar. The need to increase our use of coal during the last two decades of the 20th century is reason enough to believe that the future growth of the coal industry is assured. A major impediment to that growth might be backward national public policies that could restrict the full utilization of our coal reserves. These policies could result from overregulation and a failure of the public to recognize that coal use, with proper techno- logical safeguards, is compatible with our society&apos;s environmental-quality objectives. Communication of this problem and its solution is a major undertaking of the coal industry in the 1980s. At the end of the 1970s, the American coal industry was producing approximately 635 Mt/a (700 million stpy) of coal. To meet the nation&apos;s projected energy needs by 1985, the annual tonnage must be doubled. A similar scenario is predicted for the rest of the world. Such growth in the modern international business world will require huge additional amounts of capital, equipment, and people who know how to wisely raise and apply the capital ; use the equipment productively; and deal with the many community, public, and governmental problems such expansion will create. Whether a student&apos;s interest is in actual mining operations, business administration, engineering, finance, law, industrial relations, marketing and sales, or public affairs, a career opportunity is available in the industry.

Jan 1, 1981

By L. Adler

INTRODUCTION The purpose of this paper is to describe in engineering terms the singular and basic operational kinematics of all excavating and bulk handling equipment. The safe and efficient use of equipment will be fostered by enabling the engineer to conceptually duplicate the operators&apos; "tasks" in directing and controlling it. A simple graphical and notational scheme will be introduced to define the essential gross repetitive motions. The significance of this effort includes filling a vital analytical gap at the work face, and in establishing direct communications between the engineer and equipment operator. Since all types and sizes of earth- moving equipment are covered, a major concern has been to integrate equipment specialties into d single encompassing discipline. Equipment types are closely related to the working conditions, and their selection and evaluation are also considered. The extension to human factors analysis is natural and predictable. Since human [actors are involved, the operational analysis can also be considered a catch-all for many subtle vagaries. BACKGROUND Symbolic modelling linked to a notational system will be developed and intensively used. This constitutes the "language of science," providing a shorthand method which gives immediate recognition, is fluent, explicit, reinforcing, unequivocal and provides limitless associations. Many examples of symbolic modelling exist in chemistry, physics, the military, engineering sciences and it is a major tool in mapping. Its use is so ubiquitous that it often goes unnoticed. On the other hand it must be realized that something is lost in simplifying and idealizing what is an extraordinarily complex occurrence. The components describing the basic operational kinematics of equipment include: (1) the vehicular motions as a rigid body and (2) the job-end motions focussing on excavating (Adler, 1985). These provide all of the components in the load-haul-dump sequence (L-H-D) , and will yield three dimensional expressions. Complex patterns can also be assembled from these simple elements. An existing equipment designation employed in earthmoving will be integrated into this approach (Carson, 1961). Along with the basic motions, corresponding working conditions will be noted.

Jan 1, 1986

By K. C. Carriere

INTRODUCTION The purpose of this paper is to introduce the reader to basic control strategies for solid/liquid separation in mineral processing and to indicate some of the implementation difficulties to be encountered, without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with control systems and with dewatering processes, since exploration of these topics would require considerably more length. The paper is organized into three parts: first a general discussion on the need for control of dewatering processes and of the general criteria involved, next a more detailed elaboration on control strategies for the various unit operations, and finally a case study showing a specific approach towards such a project. Motivation & Objectives The justification for implementing any control system in an industrial plant is to improve operations and thereby to increase profitability. Without this motivation, the system will likely be perceived as unnecessary and will decline into disuse, an expensive and troublesome monument to someone&apos;s ill-conceived ideas. However, when a control strategy is correctly conceived, implemented and integrated into operations, it can provide significant advantages in operating ease and efficiency, and a handsome return on investment. In general terms, the objectives in establishing a control system are: • stabilization of process disturbances maintenance of product quality • maximization of throughput • dearer definition of process • protection of personnel and equipment A successful control strategy must address at least some of the above criteria. However, the most important requirement is a commitment on the part of plant personnel and management to start up, operate and maintain the system, and to upgrade it to reflect current process status and operational philosophy. Process Applications In this paper, control strategies will be explored for the most common methods of dewatering of mineral pulps. These unit operations include: drying, centrifuging, filtering and sedimentation. While the first three are important, they do not tend to be as complex as sedimentation, and thus will not be as exhaustively treated. Sedimentation is very widely applied, not

Jan 1, 1986

By Stefan Lorenz, Robert Galler

"The technical lifetime of underground structures does not only depend on the long-term behavior of individual support elements and material characteristics, but also on various boundary conditions, which influence the entire long-term system behavior of the structure. Thanks to the construction of second tunnel tubes and the corresponding cross passages sampling of support materials such as shotcrete, concrete of the inner lining and rock bolts including sheet membranes is possible. To evaluate the stresses and the supporting effects of the tunnel shells, flat-jack tests and different simulations were performed. With these simulations the percentage of the load bearing behavior of the shotcrete shell can be determined. From the results, conclusions for new design approaches for tunnel construction should be generated. New concepts, in which the outer lining is part of the permanent support elements can be considered. This approach would be applicable for conventional as well as mechanical tunneling. INTRODUCTION Tunnels are an indispensable part of modern transport infrastructure. As multi-generation structures their long-term preservation as well as their technical service life is of central importance. The current state of research in the field of durability of structural elements must be considered separately. In almost all areas a prediction of materials and structural components towards lifetime exists. System-wide investigations were rarely performed, so that there is no technical lifetime consideration of the outer lining in systems included. In this study the mechanical behavior of the interface connection in a double shell lining (DSL) tunnel was investigated in laboratory tests. Objective The target of this work is, at first, to create a large database with the lifetime of different structural elements and materials, which may be the basis of durability considerations of tunnels. Secondly, the goal of these investigations is to optimize tunnel designs and their dimensioning regarding to the technical lifetime. For that matter, it is necessary to analyze the selected approaches of the loss of strength and stiffness of the outer lining."

Jan 1, 2016

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam&apos;s operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer&apos;s Office and in accordance with recommendations in a report done for the Corps of Engineer&apos;s Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By Thomas A. Boyce

Introduction Although innovative coal extraction technology can be approached from many angles, this paper focuses on three: innovation in response to rising costs, to changing mining conditions, and to regulatory issues. Before exploring these three subjects, however, a basic question needs to be raised. Why Innovation? Coal is widely heralded, and quite correctly so, as the United States&apos; "ace in the hole." It has been said that the U.S. is to coal what the Arabs are to oil. The implication is that we have nearly inexhaustible reserves - that coal is cheap, plentiful, and easy to extract. Indeed, because our current productive capacity is estimated to be 15-20% greater than demand, we have been given a false sense of security about the ease of future coal extraction. Therefore, innovative measures are being concentrated on developing technologies for the demand side of coal, including power generation, synthetic fuels, and industrial applications. What is often forgotten is that the unit cost of producing energy from these new technologies depends critically on the cost of the coal feedstock -in some cases the coal consumed accounts for more than one-third the total cost. Thus, while the developers of the end-use technologies struggle to improve the overall thermal efficiency of their process by one or two per¬centage points to make the energy produced competitive in the marketplace, they often are unaware of the risk of a 3 to 6% increase in coal costs wiping out the expensive, hard-earned results of their research. Energy planners are just beginning to realize that coal is not a uniform commodity available at low cost in infinite quantities. Coal is a heterogeneous material whose cost and quality vary widely with local conditions. To produce the massive amounts of projected coal-based energy at reasonable costs, we urgently need devel¬opments in extraction technology, as well as in end-use technology. Thus, coal extraction, coal conversion and utilization, and end -use energy consumption must be viewed as highly interdependent parts of an energy supply network (Fig. 1). And current emphasis on conversion and utilization must be balanced by more emphasis on upstream technologies, including coal extraction. Even more important, the impacts of innovation (or the lack thereof) in any one technology area in the energy supply network need to be discussed and understood by those working in each of the other areas. Why innovation in coal ex¬traction technology? Figuratively, we are all in the "coal boat" together - geologists, miners, transporters, processors, power producers, distributors, and consumers. Innovation is required from each of these sectors to overcome the obstacles that prevent greater use of our most abundant national energy resource. All other links in the coal energy supply network depend on large volumes of coal produced at reasonable costs. Declines in productivity, therefore, must be reversed; the more difficult mining conditions that will be encountered call for new methods and equipment, and regulatory issues must be resolved if the coal ex¬traction link is to be a strength rather than a weakness in the planned U.S. transition to an economy based more on coal and less on imported petroleum. Innovation Tailored to Regional Conditions Once the importance and urgency of innovative coal extraction technology has been grasped, the next step - implementing a research program - becomes quite

Jan 1, 1980

By L. T. Larson

Nothing in Turkey is simple. Its his¬tory is long and convoluted, its culture fascinating, its metallogeny diverse, and its geology very complex. This article will focus on the geology of western Anatolia and the precious metals poten¬tial of this third of Turkey. Any gold produced by mines in Tur¬key since the early 1900s has been a by-product of the mining for other met¬als, such as copper from the massive sulfide deposits of the Pontics. Archaeological records, however, prove that gold was mined from the Pactolus (present day Gediz) River and refined by Croesus at Sardis in about 550 BC. Other records and legends make it possible that gold was mined before 1200 BC for the Homeric City of Troy (Priams treasure?) about 25 km (15 miles) east of Canakkale at Mad¬endag and Kartaldag. A final legend of antiquity suggesting gold in what is now Turkey relates to King Midas. And, indeed, the city-state belonging to a king of that name has been recognized near the city of Eskise¬hir. More recently, precious metals have been mined at Madendag-Kartaldag in the late 1800s. Arapdag, near Izmir, remains the only "authenticated" epith¬ermal precious metal deposit in Turkey (Mosier et al., 1985). With this spotty record, why the sud¬den interest shown by at least five Euro¬pean-based, three or four US-based, and several other international mining firms and their Turkish subsidiaries? Like other aspects of Turkey, the complete answer is not simple but, reduced to its basics, has three parts. Turkey, relative to many developing nations, has a stable, democratic form of government (although it also has a for¬midable bureaucracy) whose currency exchange rate is premised on the US dollar. New laws promulgated since 1983 have opened the country and welcomed foreign investment. Some have even provided investment incentives. The Mining Law of August 1985 made sweeping reforms of the old land tenure system. This law made it possible for a foreign-based company to have a wholly-owned Turkish subsidiary en¬gaged in mining. Equally important is the belated recognition that western Anatolia, while geologically compli¬cated, is today basically a province Neogene extensional tectonics having many of the geologic attributes of the leading gold producing province of the US - the Basin and the Range. Geologic rationale for precious metals exploration Tectonic/lithologic framework: Alle¬gorically and simplistically, Anatolia during early Neogene (middle Miocene) can be likened to a tube of toothpaste with the cap off. It is squeezed in the vise formed by the Arabian plate mi¬grating north toward the southwest end of a stable Asian platform. The "tube" was compressed. It could not expand to the east because it was sealed by what is now southern Russia and Iran. The filling of the tube escaped to the west, in the direction in which the cap was miss¬ing (Fig. 1). So developed during the middle to late Miocene the western-most struc¬tural province of Anatolia. This was done by a process aptly termed tectonic "escape" by Sengor et al (1985). This province is dominated by exten¬sional tectonics much like the Basin and Range of the western US and has an estimated extension of between 30% and 50%. The most striking manifesta¬tion of this extension is the 10 to 11 major east-west trending grabens (Ge¬diz, Buyuk Mendares, Kocuk Mendares, etc.) and intervening horsts, although a much greater number of smaller, gener¬ally northeast-striking grabens and half

Jan 1, 1989

By J. A. Brierley, S. R. Hutchins, C. L. Brierley

Introduction Many gold and silver ores are refractory to conventional processing technologies. Thus, precious metals recovery is uneconomic. These resources can consist of ores, flotation concentrates, mill tailings, and other reserves. The refractory nature of these materials can be ascribed to such components as iron sulfide minerals, silica minerals, tellurides, organic compounds, and sulfosalts. Precious metals locked within iron sulfide minerals account for a large number of refractory gold ores. These minerals consist principally of pyrite or arsenopyrite. They must be oxidized to liberate the encapsulated precious metal and allow its contact with the leaching agent. Carbonaceous gold ores represent a unique class of refractory precious metal ores in general. Not only does gold encapsulation by iron sulfide minerals occur (Hausen, 1985), but these ores also contain organic matter that interferes with gold recovery by cyanidation. Direct interference can be attributed to either occlusion of gold within organic matter or formation of a stable gold-carbon complex. The magnitude of this problem is debatable. Wells and Mullens (1973) examined two carbonaceous gold ores and found no association between the gold and carbonaceous material. A more common problem is indirect interference, whereby the aurocyanide complex formed during cyanidation is sorbed by the native organic matter and is not available for recovery. This phenomenon is referred to as "preg robbing" (Osseo-Asare et al., 1984; Hausen and Bucknam, 1984). Guay (1981) summarized various methods that can reduce preg robbing during processing of carbonaceous gold ores. However, some are not applicable to carbonaceous ores that have significant amounts of gold locked in iron sulfide minerals. Several methods exist for oxidizing iron sulfide minerals and rendering refractory precious metal ore amenable to conventional recovery processes. These include various embodiments of roasting (Jha and Kramer, 1984; Brown, 1984; Arriagada and Os-seo-Asare, 1984; Smith, 1986), pressure oxidation (Muir et al., 1984; Beattie et al., 1985; Thompson, 1986; Weir et al., 1986; Argall, 1986), and chemical oxidation (Scheiner, 1971; Jackson, 1983; Van Weert et al., 1986). Each process has been successfully used for refractory precious metal ores. In many instances, however, their use is precluded by capital and operating costs relative to the value of the ore. An alternative to these methods is microbial pretreatment - a biological process whereby iron sulfide minerals are degraded and the liberated precious metal values can be recovered by conventional technologies. Bioleaching refractory precious metal ores is a relatively new concept compared to roasting and chemical oxidation. It is rapidly becoming established as a viable pretreatment alternative. Numerous studies have been conducted in the laboratory and on a pilot scale (Yudina et al., 1979; Lawrence and Bruynesteyn, 1983; Pol &apos;kin et al., 1985; Marchant, 1985; Livesey-Goldblatt, 1985; Gibbs et al., 1986). Comparative tests have demonstrated that bioleaching can be equal to or better than roasting or pressure oxidation in terms of product recovery and process economics (Fridman and Savari, 1983; Livesy-Goldblatt et al., 1983; Karavaiko et al., 1985; Gilbert et al., 1986; Hackl et al., 1986). Bioleaching&apos;s main drawback is that pretreatment requires days rather than hours. This can lead to excessive operating costs for difficult-to-treat ores. In all of the tests reported thus far, the leaching microorganism used has been thiobacillus ferro-

Jan 4, 1988

By P. T. Perdue, F. F. Haywood

INTRODUCTION Monitoring devices used for detecting and measuring airborne radon in mines are limited due to the rugged environment in which they must operate. Personnel monitors now available are either passive or require filters and an air pump. Area air monitors usually have bulky batteries or require electric power service to the instrument. Thus, there are few instruments presently in use in mines capable of discriminating between the various radon isotopes and their daughters. Occasionally it is desirable to determine which radon daughters are the principal dose contributors in mine air. In some areas, such as the Elliot Lake mine in Canada, there exist sizable quantities of 220Rn in the mine air due to 232Th in the ore (Cote and Townsend, 1981). Since there has been recent interest in radon daughters in homes and factories, as well as caves and mines, methods and instrumentation are being developed to address these cases. Some of these methods can be employed in uranium mines. Although there have been very few determinations of the three radon isotopes (222Rn, 220Rn, and 219Rn) and their daughters made in uranium mines, these isotopes have been measured in process buildings and in private homes under circumstances that suggest these isotopes could also be present in uranium mine air (Perdue, Leggett, and Haywood, 1980; Yarborough, 1980) METHODS Cryogenic air sampling was developed about 15 years ago (Rasmussen, 1972) to concentrate various airborne chemicals for later fractional distillation and measurement of various organics using gas chromatography. A version of this technique has been developed to measure tritium, krypton, and other radioactive gases in nuclear power station buildings (Anon, 1980). In this method, fractional distillation is used in conjunction with various detectors to identify the radionuclides present. The cryogenic method to be discussed here was developed at Oak Ridge National Laboratory (ORNL). It uses the liquid air accumulated in a sampling device for a direct analysis of all gamma-ray emitters present. The air sampler (Fig. 1) could be employed in a mine to liquefy air, using the difference between the point of liquefaction of air (~80 deg. Kelvin) and the boiling point of liquid nitrogen (77 deg. Kelvin) to liquefy an air sample. By using a proper orifice at the entry to the sampling vessel, air of any dust concentration and relative humidity [ ] may be sampled. The energy for sampling is provided by the slow evaporation of the liquid nitrogen; no other power source is required. This type of sampler could be used to augment the usual filter and pump, or passive system presently employed to estimate personnel dose from radon daughters. It would also allow measurement of any combination of daughters from the three radon isotopes. Upon completion of sampling, the sampler is closed and removed from the mine. This sampler, with its liquid air contents maintained by the slow evaporation of liquid nitrogen, is taken to the place of measurement. There, the sampler is opened, the accumulation of water and ice in the neck is chiseled down into the liquid air, and the sample is transferred quickly to a precooled counting dewar (Fig. 2). This counting dewar is then placed upon a gamma radiation detector; we recommend a high purity germanium detector. A determination of all the radon daughters can be made in 1 to 4 hours after the sample is taken.

Jan 1, 1981

By Mark Board

INTRODUCTION As the world&apos;s supply of near-surface metalliferous ore bodies is depleted, more emphasis must be placed upon mechanized bulk systems of underground mining. In particular, block caving is becoming increasingly important as a method of mining low to moderate grade deposits at depths of somewhat less than 1219 m (4000 ft). 00 ft). The block caving method requires that the ore body be completely undercut, thereby removing its means of support and inducing failure which progresses from the undercut to the ground surface. As the span of the under- cut increases and the weight of the overlying crushed ore body becomes greater, large stresses are induced on slusher and haulage drifts. Stability of these drifts is critical in block caving operations and often proves to be an extremely difficult task (Kendorski, 1976; McWilliams, 1975). Slusher drift maintenance can be costly, often exceeding that of the original support costs. This chapter analyzes the ground support problems of an Arizona block caving mine. The mine presently uses monolithic concrete liners as a support method. Failure of the liners occurs as the undercut approaches, thus initiating a maintenance problem which will continue until the ore body is depleted in that block or panel. To examine this problem, a simple analysis of the stresses induced by the advancing undercut was per- formed. Utilizing a design method developed by Dixon ( 1973, 1974), the calculated stresses were used to deter- mine the minimum thickness required for varying section shapes of unreinforced concrete liners. It is found that the thicknesses required for stable linings are not economic. Recently developed empirical methods of support de- sign are utilized (Barton, 1974; Bieniawski, 1973) and compared to the analytical method. A final discussion of alternative methods of support is given with recommendations for the use of passive or "yielding" support methods. LAKESHORE MINE (GENERAL GEOLOGY) The Lakeshore copper property is located in Pinal County, AZ, approximately 45 km (28 miles) south of Casa Grande. The Lakeshore deposit is a porphyry cop- per similar to others in Arizona. The ore body consists of disseminated chalcopyrite and fracture fillings in quartz monzonite porphyry (QMP), Cretaceous volcanic (KVS), Precambrian diabase, and Mescal limestone. The ore body has been divided into three distinct zones of mineralization which have been termed (South, 1972) the oxide zone, the sulfide zone, and the tactite zone. The oxide zone occurs in the upper portions of the ore body and consists primarily of leached and oxidized quartz monzonite porphyry and Cretaceous sedimentary and volcanic rocks. The sulfide zone underlies the oxide zone and includes all quartz monzonite porphyry and Cretaceous rocks which have not been oxidized. The thickness of the sulfide zone is variable and ranges from about 61 to 122 m (200 to 400 ft). The tactite zone occurs in a series of Paleozoic metasediments consisting of tactite, quartzite, diabase, hornfels, and dikes of quartz monzonite porphyry. The tactite zone is highly variable in thickness and underlies the Cretaceous volcanic and sediments throughout the mine. Together, the tactite and sulfide zones are known as the thick or tall sulfides. The greatest support stability problems occur in mining of the tactite zone and are therefore the subject of the remainder of this chapter. MINING METHOD The Lakeshore mine is a block caving mine utilizing a panel caving method. The present mine consists of two

Jan 1, 1982

By E. Topuz, Xing Wu

INTRODUCTION The air flow in the mine ventilation network can be categorized in three ways: natural splitting, controlled splitting, and semi-controlled splitting. In natural splitting, the air flow in branches of a ventilation network apportions itself according to the aerodynamic resistance of the branches. In controlled splitting, a prescribed quantity of air is circulated through each branch. In semi-controlled splitting, flow in some branches is fixed to a desired quantity while in other branches it is split naturally. In practice, the mine ventilation networks present the latter two situations. Usually, the resistance of each branch in the network is known and the quantity of air in the working place is predetermined by safety considerations. If the number of branches whose airflow quantities are known is equal to or larger than the number of the fundamental meshes in the network, then the network becomes a controlled splitting network (Wang, 1982 a). Otherwise, it is a semi-controlled splitting network. If no booster fans are used in the network, the problem can be solved as either controlled or semi-controlled splitting networks in order to determine the main fan pressure and regulator size and location. All techniques are based on Kirchoff&apos;s flow and energy conservation laws and Atkinson&apos;s Equation. Booster fans can be used in controlled and semi-controlled splitting networks. It has been proven both theoretically and practically that using booster fans in these ventilation systems can improve flow distribution and reduce consumption of power (McPherson et al., 1985). The current techniques used in determination of booster fan location and size include simulation, linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing. These techniques can be classified into two groups. The first group, including linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing techniques, deals with controlled flow networks. The second, simulation, can be applied to the handling of semi-controlled flow networks. Mathematically, the problem of controlled splitting networks can be solved more easily than that of semi-controlled splitting networks. This is because the controlled flow network can be formulated as a linear programming problem, for the solution of which there are several sophisticated algorithms. Moreover, the semi-controlled flow network is usually modeled through nonlinear programming, for which there are no universally applicable solutions. The procedure described by Wu and Topuz, 1986, can be used to convert a semi-controlled network to a controlled flow network, and the problem can then be easily solved by the techniques used for solution of a controlled flow network problem. In practice, a mine ventilation network may change from controlled splitting to semicontrolled splitting with advancement of mining. This dynamic nature of mine ventilation makes the problem more complicated and necessitates development of new solution procedures which will consider the overall economics of the system. CONTROLLED SPLITTING NETWORK The problem in controlled splitting networks with booster fans is to determine the operational characteristic of the main fans, and the location and size of booster fans and regulators. The objective is to satisfy the air flow rate requirement for each branch while minimizing consumption of energy. The techniques used for the controlled splitting network problem include linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing. The objective function and constraints can be expressed as follows (Wang and Pana, 1971): [ ]

Jan 1, 1989

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

5.1 INTRODUCTION There are several types of surface ground disturbances, each of which is immediately transmitted to surface structures and causes damage of various forms, depending on the location of the structures in the subsidence basin. Many criteria have also been proposed for defining the potential structural damage. All of these topics will be discussed in this chapter. 5.2 TYPES OF GROUND DAMAGES There are two types of ground damage, continuous and dis¬continuous, that could inflict damages to surface structures. Dis¬continuous ground damage is open fractures of various degrees. Four types of fractures are commonly seen (Brauner, 1973b): 1. Fissures or cracks. Cracks are the most common form of ground damage and range from completely closed to several feet wide. Surface cracks are most prominent when the ratio of mining depth to mining height is smaller than 30 to 50 times mining height. Cracks initiate parallel to, but ahead of the moving long¬wall face at some intervals when the depth-to-mining height ratio is less than 25 to 30. As the face continues to move, they open up and then close gradually, and in most cases eventually close up completely when the face moves farther away. Sometimes when the depth-to-mining height ratio is larger, cracks may initiate be¬hind the face and go through the same cycle. Cracks are also more likely to occur in the hill when the face is moving in the uphill direction. Cracks also occur at or near both sides of the panel edges. Those cracks tend to remain open permanently. When the surface is covered with grass or other vegetation, cracks of less than 1 to 2 in. wide usually do not penetrate it and become invisible on the surface. 2. Steps. A step may occur when the longwall face stops abruptly if the mining depth-to-mining height ratio is less than 20. Steps may also occur along the panel edges. Steps also range from a few inches to a few feet in width and depth. If planes of weakness are oriented favorably, ground will slide along these planes and form steps on the surface. 3. Cave-in pits. These result from local collapse of the ground from the mine level to the surface when the mining depth is less than 150 ft and occur mostly above abandoned mined lands. They may be as large as 40 ft wide and deep. 4. Bumps (compression ridges). Bumps result from ground compression and occur mostly near panel center some time after mining. Bumps of up to 4 ft, but mostly 1 to 2 ft, have been identified. Continuous ground damage refers to the formation of the sub¬sidence basin where continuous nondestructive ground deforma¬tions occur. As mentioned earlier, continuous ground deforma¬tions associated with a subsidence basin include subsidence, slope, curvature, displacement, horizontal strain, twisting, and shearing. 5.3 TYPES OF SURFACE STRUCTURAL DAMAGES Both continuous and discontinuous ground disturbance cause damage to surface structures. A. Structural Damages Due to Discontinuous Ground Disturbance 1. Fissures or cracks. Open cracks can cause dislocation of surface structure if the gaps are sufficiently large so that the struc¬tural elements cannot resist but fail. On the other hand, minor cracks affect only the appearance, and not the structural integrity. 2. Steps. When a surface structure is located on a step, some portions of the structure lose support and become overhung. In the case of a residential house, there will likely be many open frac¬tures in the overhung portions, followed in severe cases by sepa¬ration of the superstructure at the edge of the step. 3. Cave-in pits. If the caved-in pit is larger than the surface structure, the structure will drop into the pit and become unstable. If the caved-in pit is smaller than the surface structure, the struc¬ture may either become overhung or lose support in some portions. In either case, it is unsafe for use. 4. Bumps (compression ridges). Bumps will disrupt roadways or house floor. If located under supporting members of the struc¬tures, it may cause damages. B. Structural Damage Due to Continuous Ground Disturbances 1. Subsidence. Pure subsidence or uniform subsidence over an area does not cause any structural damage. However, if it becomes a topographical low area, it may be flooded with water and make the surface structures unusable. It must be noted that the flat bottom area at the center of the final supercritical subsidence basin does not reach that position suddenly. Rather, as shown in Fig. 3.1, it is subjected to the dynamic surface deformation asso¬ciated with the traveling subsidence basin before it is left behind to be part of the flat-bottom area. Therefore any structure located at the center of the final supercritical subsidence basin must be able to resist the dynamic surface deformation in order not to be dam¬aged. 2. Slope. Ground slope will induce tilting of the structure. Tall structures with small base areas, such as water towers, chimneys, and power transmission towers are most sensitive to ground slope. If the ground slope is such that if after tilting the center of the gravity of the tilted structure falls outside the base area, it will topple, but this seldom occurs. Ground slope will change the designed slope of a buried trans¬portation pipeline, either increasing or decreasing the original slope depending on whether the ground slope coincides with or opposes the original slope. There are maximum allowable final slopes for various types of transporting materials. Ground slope also affects highways and railways. There is a maximum allowable final slope for a railway because tractive effort increases 1/1000 of its weight for every increase of 1/1000 in grade. 3. Curvature. There are positive (convex) and negative (con¬cave) curvatures. When a surface structure is located on a positive curvature, both ends become unsupported, followed by bending upward at the midportion. The top portion is subjected to more severe stretching than the lower one. As a result, vertical cracks with a wider gap at the top occur at the window, door frames, on the walls, and at -the wall joints. V-shaped cracks appear at the

Jan 1, 1992

By Richard L. Breithaupt

INTRODUCTION A shuttle car is a self-propelled rubber-tired haul¬age vehicle designed specifically for underground min¬ing, primarily in coal mines (see Figs. 1 and 2). The drive mechanism is located on the sides of the vehicle, and the load is carried in the center. A chain-and-flight conveyor distributes the load when the car is being loaded by a loading machine or continuous miner and also discharges the load onto a conveyor belt or into a mine car. As the name implies, the shuttle car shuttles back and forth between the working face and the un¬loading point and is not required to turn around. Shuttle cars have served as primary haulage in this country since 1940 and still perform this function in most coal mines today. TYPES OF SHUTTLE CARS Shuttle cars may be battery-powered, diesel-powered, or cable-reel electric powered. Battery-powered cars were used between 1940 and 1950, but are almost out of existence today because of their limited power. Diesel cars have been used in coal mines, but are used mostly in noncoal mines where rules and regulations are not as stringent. Also, objections by organized labor have limited the use of diesel-powered shuttle cars in coal mines. Today, the largest number of shuttle cars are cable-reel cars. Electric power is fed through a cable stored on a cable reel that may have a capacity from 152 to 244 m (500 to 800 ft), depending upon the size of the cable and the cable reel (see Table 1). This, of course, limits the travel of a shuttle car. However, time studies have shown that for the most efficient haulage cycle, the length of haulage should not exceed 91 m (300 ft). As haulage distance increases, the waiting time for the loader or miner becomes longer, and haul¬age efficiency suffers. Cable-reel cars are manufactured in standard hand and opposite standard hand models. A standard car has the operator&apos;s control on the left front side and the opposite standard car has the opera¬tor&apos;s controls on the right front. Generally a loader or miner operates with two shuttle cars, one of each type. This allows the trailing cable to lie on either side of the entry and prevents the cables from fouling each other. Shuttle cars are designed to operate with either dc or ac power. Cars using dc power are designed for 250-v supply and ac cars are designed for either 440, 550, or 950 v, three-phase voltage. Most coal mines that are relatively level can use dc cars where dynamic brak¬ing is not required. For mines having steep grades (in excess of 15%) ac cars are used because ac traction motors have inherent dynamic braking and are safer when tramming downgrade. A recent innovation in shuttle car design in the last five years has been the introduction of an ac/dc car. This design utilizes ac input power through the cable, and the power is rectified on the car to 250-v do for traction motors. The pump motor and conveyor motor are powered by ac voltage. The main advantage of this design is efficiency-a much smaller cable may be used and the smooth operating characteristics of the dc traction motor is obtained. This prevents shock loading on the traction drive train, which is an undesirable feature of ac traction motors. SHUTTLE CAR FEATURES Elevating Discharge Today, all shuttle cars are equipped with an elevating front conveyor that allows the shuttle car to discharge into a mine car or belt feeder without the use of ramps. Hydraulic Power System Today, all shuttle cars are equipped with an hy¬draulic power system. An hydraulic pump is driven by an electric motor which provides hydraulic power for steering, elevating the front conveyor, and powering the

Jan 1, 1982