Search Documents

Part two of this three part series looks at explosives use in open-pit and underground mining operations. Part three, next month, will discuss the transportation, storage, handling, and destruction of explosives. Larger ore bodies, lower grade deposits, and more difficult geologic conditions have led to changes in blasting products, techniques, and field practices in both open-pit and underground metal mines. Pit blasting operations must consider the material's geology, needed fragmentation for the material, and hole diameter and depth-as well as the traditional consideration of the type of explosive used. With underground mines, various blasting aspects of burn, angle, and machine cuts must be considered for an efficient and safe operation. Of the factors related to open-pit blasting, geology of the material is most important. Many theories relating to sonic velocity and rock hardness are used to determine needed explosives ratios. Extensive field tests are necessary to determine these factors. In most cases, results assume that the material to be broken is homogenous. The drilling penetration rate is sometimes used as a guide to determine rock hardness; however, this is not necessarily a good idea. In many cases, a very hard, brittle rock will blast with less difficulty than a soft, spongy rock. The formation's stratification is also important. In thinly laminated horizontal seams, rock will usually break and adequately fragment with relatively large burdens and spacings using a low explosives ratio. Massive formations with few laminations require close burdens and spacings and a high explosives ratio. When the stratification is pitched on a severe angle, it is usually preferable to develop the pit face 90°-but no less than 45°-to the stratification. If the face must be developed parallel to the stratification, burdens and spacings must be reduced and the angle drilling that will conform to the angle of the lamination should be given serious consideration.

Jan 8, 1981

By Gregg Wilkerson

The Blind Springs Hill pumice beds are located 5 miles southwest of Benton, California in the foothills between the Benton Mountain Range and Blind Springs Valley. The best exposures of the pumice are in an area 0.75 miles west of Blind Springs Hill. The pumice is Quaternary ejecta material which came from the rhyolitic volcanoes in the Glass Mountain-Volcanic Tablelands area of Mono County. The pumice beds occur in two distinct layers separated by an unconformity. The upper layer is 0 to 11 feet thick and consists of coarse subangular pumice fragments, some of which are over 1.75 inches in diameter. The lower bed is medium to coarse grained with subangular fragments up to 1.0 inch. The lower bed is 0 to 9 feet thick. Overburden at the Blind Springs Hill deposit varies from 0 to 15 feet. There are approximately 1 million cubic yards of material in the deposit that can be mined. The size distribution in the deposit is mostly fine with only 10.6% of the pumice fragments being over 0.5 inch in diameter, the minimum size needed for stone-wash or acid-wash applications. Suitability of pumice for the textile industry is quantified by standard 15-minute abrasion and absorption tests. In the Blind Springs Hill deposit, the plus 0.5 inch fraction has an abrasion loss of 33% which is too high for stone-wash application but it has an absorption capacity of 36% which makes it suitable for acid-wash applications in the textile industry. The abrasion and absorption properties of this deposit are within the range of those which have been measured for other pumice deposits within the United States.

Jan 1, 1995

By P. M. Fozzard

The Chaucha porphyry copper/molybdenum deposit was discovered by a United Nations team of geologists working with a ?counter- part" team of staff of the Ecuadorian government's General Directorate of Geology and Mines (DDGM) in July 1968. The exploration program formed the latter part of phase I work plan of a two-phased exploration project financed by the United Nations Development Programme and initiated in late 1964. The author was a team geologist during the period 1965-1967 and subsequently project manager for the period 1968-1972. The Chaucha property lies some 10 km (6 miles) east of the north- south-running western boundary of what was known as Operation Area No. 5. This area of some 10 500 km2(4050 sq miles) is a square truncated to the southeast and centered on the city of Cuenca, the major provincial capital (Azuay Province) of southern Ecuador. The eastern half of the exploration area is dominated by the Cretaceous- Tertiary sedimentary valley (basin) of Cuenca (Caar-Azuay) and its related drainage area. The western half, in which Chaucha lies, is dominated by the high Cordillera Occidental volcanic plateau and the western erosional valleys of the Andes draining to the Pacific. The valley that dominates the eastern part of the area [I500 m (4920 ft) above sea level] is transected by the Pan-American Highway. Because of increased agricultural activity associated with the Cuenca Valley, the area is reasonably well covered by a road network of varying quality. The high western area up to 4000 m (13,120 ft) in altitude is largely barren and completely inaccessible by vehicle. The geological reconnaissance map of the region is shown in Fig. 1.

Jan 1, 1991

By Stephen G. Hardcastle

3D-CANVENT is a software package that integrates advanced computer aided design (ACRD) true 3D graphics with a mine ventilation simulator. The package runs as a Windows(tm) application to access its printer drivers environment and does not need third party CAD software. It is composed of two primary modules: DMVENT and MINEDESIGNER. DMVENT is a traditional Fortran coded Hardy-Cross iterative ventilation network solver written in 1980 with thermodynamic capabilities. This module is relatively unchanged with the traditional data input options for branch type, specified or calculated resistances, fixed flows, and fixed or variable pressure fans. MINEDESIGNER is the graphics engine that optimizes the ventilation design process. It performs the front-end transformation of input data entered in the graphical interface into the correct format for the solver. At the back-end it reconverts the historically standard tabular data output from the solver into an easily viewed graphical format. ACRD features of MINEDESIGNER are used to generate a 3D wire-frame node and branch network of the mine's ventilation system. The network can be displayed in up to 4 views orientated to XYZ planes or a 3D view. All the views have zoom, pan, slice and rotate options. The graphical interface efficiently permits data entry and editing via a mouse with pick-and-point item selection. Branches can be found or added with "search" and "join" options. Visual interpretation is enhanced by the 16 colour options for branches and numerous graphical attributes. Network locations are readily identified by alpha-numeric names for branches, junctions and fans, and also the logical numbering of junctions. The program is also readily expandable for pollutant simulation and control/monitoring applications.

Jan 1, 1995

By Francis R. McAllister

SYSTEM ENGINEERING Years ago, while attending Harvard's Advanced Management Program, Professor Robert Hayes introduced our class to the, then not-so-familiar, concept of systems engineering. First assignment-dinner at The Benihana of Tokyo Restaurant! Delighted, but a bit mystified with the assignment; we had dinner at Benihana. Back in class, Professor Hayes inquired about the assignment and persuaded us; that Rocky Aoki's business formula for Benihana was not necessarily Japanese cuisine, but rather the systematic way in which he moves more people-if you will, processes more people through his restaurants than his competition, by systematically linking all restaurant functions. For instance, the bar is a holding area in which patrons ideally wait no more, or no less, than 20 minutes. When seated, your table, which accommodates eight, is filled with eight even if you are a party of two. The Japanese chef is also the entertainment, and when, at the end, he cleans the grill, you are being subtly prompted that dinner is over. The bill accompanies ice cream, systematically delivered shortly thereafter. You are expected to pay promptly and depart, as there are eight more, mostly unacquainted, people who have waited 20 minutes in the bar, and who are assembled ready to be seated at your table. For me-this was electrifying. I understood the concept, concluded it was very powerful and felt prepared to conquer whatever, by means of its application. That was years ago and I can safely say I have yet to fully realize on the euphoria of that moment. Why? Well, I simply conclude: • The concept of systems engineering is simple and not revolutionary, but The application of systems engineering is far from simple and is revolutionary.

Jan 1, 2004

By Sidney L. Hansen

This report was written because of concerns of the possible error involved when stopping leakage is incorrectly assumed to be turbulent. It is common practice to use turbulent flow to characterize each airway branch for computer models of mine ventilation circuits. This report addresses computer methods to accurately model air-leakage paths. A graphical method is described for deriving the equations of leakage through stoppings. The significance of modeling leakage according to the proper flow regime (turbulent or laminar) is demonstrated by the following method. A hypothetical mine was developed to represent present-day conditions. The stoppings of the mine were chosen to leak according to laminar flow properties. The mine was represented by constructing two base models. One base model used turbulent leakage equations for each stopping, while allowing the corresponding resistances to vary. The other base model used the correct laminar leakage equations and held corresponding resistances constant. The mine circuit was then expanded to demonstrate future development. The expanded portion was designed with stoppings that were identical to those in the base mine. The mine in the future state was represented by two projection models. Each projection model was an extended version of its associated base model; one used turbulent leakage equations and one used laminar leakage equations for stoppings. The laminar projection was theoretically correct and is used as a basis for comparison of differences in airflow quantities. Rather than modeling every leakage path for stoppings, a more practical approach is also discussed. A good level of accuracy is maintained by combining leakage paths if the proper flow equations are used. This method was used on the hypothetical mine projection and the flows were very similar to the theoretical values.

Jan 1, 1989

By D. C. Torre

Ever since the introduction of the first successful continuous mining machines some twenty odd years ago, there has been an obvious, and steadily increasing, need for some form of continuous haulage machine, or system to work with them. There is universal agreement that the continuous mining principle, and the various continuous mining machines in particular, have done a great deal for mining. However, coal mining men, who have the longest and broadest experience with them, agree that continuous miners do not truly mine continuously. In fact, their estimates, and actual studies, show that the real mining time of these machines ranges, on the average, from 20% or less to about 30% of the available shift time. Part of the failure of the continuous mining machine to mine continuously may be ascribed to breakdowns in its intricate machinery. Most of the failure, however, is blamed on a variety of other factors. Of these, there are two which are given particular blame: face haulage and roof control. The relative importance of the two as the major negative factor in continuous mining is a moot point. However, there is an extensive concensus that haulage is the number one problem. Roof problems and their control are inhibiting factors regardless of the type of mining or mining machines employed. But the truth of the matter is that a continuous mining machine, like any type of loading machine, whether underground or on surface, is only capable of mining or producing in direct ratio to the mineable, or loadable, material that can be kept ahead of it and equally, if not more, important, that can be taken away from it. While the first commercially successful continuous miners were developed for, and proved successful in, coal mining, they were soon

Jan 1, 1974

By Y. J. Wang

Optimal sizing of a ventilation shaft is a classical subject in mine ventilation economics.. The shaft size is optimized by minimizing the sum of shaft-construction and ventilation-power costs, or owning and operating costs. The length and air quantity of the shaft are held constant, and the location of the shaft, affecting its depth, and construction and ventilation power costs, is not considered (Hartman, 1961; Lambrechts, 1974; Wang et al., 1978). This paper proposes an approach by which the location and size for a new pair of shafts (intake and return shafts) are optimized for a coal-mine ventilation network. Specifically, the problem is to determine the location and size for a new pair of shafts, and the distribution of air between the new and old shafts so that the combined cost of shaft construction and ventilation power is minimized. The shaft length or depth corresponds to the height of overburden at any shaft location. To simplify the problem, the shaft locations will be limited to the line along the main or submain entries, and the connection entries at the shaft bottom neglected. In order to calculate the ventilation-power cost, the air power of the system should be determined. This in turn requires the calculations of the air quantity and pressure of each fan in the network, satisfying Kirchhoff's laws and Atkinson equation. After obtaining the air power, the cost calculation is straightforward. In the following, we shall assume that the resistances of all airways, and the quantity for each mining section, which is controlled by adjusting the air regulator, are all known. The resistances for the shafts are determined from the estimated friction factors, and shaft dimensions and lengths. Furthermore, it will be assumed that the fans can be selected to meet the duties called for by any network solutions.

Jan 1, 1982

By W. A. Hustrulid

Introduction A problem that has faced mining engineers and mining geologists for many years is how to best explore a particular prospect so that the basic decision as to whether the material present is ore or only high-grade rock can be made with some confidence. It is obvious that one could not begin a large scale mining program on the basis of tests made on a few hand samples. On the other hand, one could not be 100 percent certain as to the average grade or tonnage before beginning development, as this would require the orebody to be mined out in the sampling process. The basic objectives of the exploration program can be stated as (1) to reduce mining risk; (2) to lessen the cost of development; and (3) to increase the profits of mining. The exploration program should be terminated when these objectives are no longer being met. The construction of tunnels is a specific mining operation. In the exploration program one should gather the data needed to determine (1) the type of excavation technique(s) to be used; and (2) the rate of advance that might be expected. As in the evaluation of an orebody, with the data collected it should be possible to estimate mining costs and project life. Unfortunately, at the present time, it is not possible to do this at least when dealing with medium to hard rock types. The reason for this, it is felt, is basically the inability to identify what specific rock mass properties are of use in tunnel design and to specify how these may be obtained in an exploration program. In short, the exploration program should be designed to give information regarding both the volume (length) and 'grade' (in

Jan 1, 1997

By John D. Smart, John W. Sager

The following paper is an evaluation of the instrumentation programs on recent Corps of Engineers tunneling projects. The authors have first-hand knowledge of the NORAD Cheyenne Mountain Complex (NCMC) Expansion Project. Information on the other projects comes from conversations with those directly involved in the instrumentation programs and from referenced reports. The specific objectives of this paper are: (1) to state the purposes of the instrumentation programs, (2) to discuss the benefits gained from the instrumentation, and (3) to present conclusions from this study that will provide guidance to those planning instrumentation on future projects. Presentation of detailed descriptions of the projects and instrumentation data is limited to that necessary to the accomplishment of the above objectives. NCMC EXPANSION PROJECT The NCMC is located at a depth of approximately 800 feet in Cheyenne Mountain near Colorado Springs, Colorado. For the current expansion project new chambers were mined to accommodate a new diesel power plant and associated cooling and air handling equipment. During 1971 some 55,000 yd3 of granite were mined through existing access tunnels for this expansion. A model of the new excavation is shown in Figure 1. The light shaded areas are new openings, and the dark areas are portions of the existing operating complex. The large chamber to the right is the power plant chamber and has a span of 67 ft, a height of 50 ft, and a length of 172 ft. The other large chamber on the lower level is the cooling tower chamber and has a span of 38 ft, a height of 45 ft and a length of 185 ft. The small chamber on the upper level has a span of 20 ft and is 27 ft high and 140 ft long. Other major excavations are the 18 ft diam air tunnel

Jan 1, 1997

By Stephen G. Hardcastle

CANMET has developed a simple yet very effective tracer gas method to test the efficiency of stench gas emergency warning systems which can easily be performed by mine personnel. This test method uses sulphur hexafluoride (SF,) as a surrogate for such stench gases as ethyl mercaptan. The test has many advantages: it is non-disruptive to production because SF, is odourless, colourless; it is safe to use as it is inert and only a small volume, insufficient to reduce oxygen levels, is necessary to dope the air with a measurable concentration; and most importantly it provides definitive results to assess the adequacy of the warning system. Specific findings of these tests have included, over doping sections of the mine and subsequent production loss due to sickness, the warning being ignored, the injection period being too short, excessive dispersion, and inadequate notification times. The simple test protocol involves releasing a known volume of the SF, under similar circumstances to those of the stench gas, and then sampling for its presence downstream. These samples are collected in air-tight syringes which are then analyzed in a laboratory with a gas chromatograph. By direct proportion, between the size of the stench and tracer gas releases, it is possible to convert the SF, concentration into equivalent stench gas concentrations profiles. From these, it is possible to define, the initial arrival time of the gas, the time it takes to reach a "target" notification concentration, whether the gas peak will exceed TWAEV, STEV and CEV exposure limits, and the duration of the peak above these levels. Since 1993, this test protocol has been employed a total of eight times on four different Canadian mine properties and the results are being used to optimize the stench gas release system with respect to volume of gas used, duration of injection, and number of injection locations.

Jan 1, 1997

By Leo Misagi

THE ROLE OF MANAGEMENT IN PLANT SAFETY Safe Production In plant management, safe production is an ideal. It becomes reality when: 1. Plant employees work in healthful and safe conditions. 2. Plant safety is in harmony with productivity. 3. Worker absenteeism and turnover are low-the work force is stable. Plant management must apply its talents, skills, and resources to build and maintain the foundations of safe production on a system of policies, procedures, and attitudes. It must do so by marshaling all managerial functions - staffing, direction, control, innovation, and representation-toward that goal. Ideally, a plant safety program is proactive. Management should plan and implement safety activities that are aimed at prevention. Past accidents-accomplished facts-should not be the sole guide of future actions. In other words, positive preventive measures, not the fewness of accidents are the criteria for safety production. An ideal safety program is one which is cost effective. Management should view plant safety as part of a broader program-loss control. Loss control includes prevention of fires and other accidents, unhealthful conditions, and occurrences that cause bodily injury, illness, property loss, or damage. Management evaluates the employees' productivity and safety. An effective training program aimed at loss control is the hallmark of safe production. Ideally, both labor and management should be well versed in safety. They believe in the premise that work-related injury and illness, as well as property loss and damage from fire and other accidents, are manageable and preventable. Such belief prompts them to learn more about the work process and potential hazards associated with each job. They also learn how to expect and prevent fues and other accidents, and respond to emergencies at the plant. Plant management determines which individuals or groups of employees are accountable for the following functions:

Jan 1, 1991

By David Pentz, Paul Hodges

GENERAL INTRODUCTION The object of this paper is to discuss those aspects of open pit mine design which are affected by geotechnical factors. The temptation exists for some practitioners of geotechnical engineering to believe that this relatively new engineering discipline is the ‘be all and end all of mining.’ In the opinion of the authors, this is fallacious but, as our ability to put numbers to the behaviour of rocks and soils improves, it is clear that geotechnical engineering will become an integral and important part of designing and operationg mines success- fully. Open pit mines in the context of this paper also includes open cast mines, where the 'ore" is extracted and the waste material is immediately replaced or ' backfilled in the mined portion of the pit. Open pit mines operating today move from very small tonnages a day to in excess of 400,000 tons per day. Several mines are operating and are being designed to capital expenditure for such projects in some cases exceeds five hundred million dollars and in a few cases will exceed one billion dollars. The size of this investment means that financing will have to be provided from banks or joint partnerships. This financial environment means that planning will be carefully scrutinized by experienced representatives of financial institutions or other mining companies. All too often a project has been put in jeopardy because the personal desire of one or two men to make a project proceed has caused incomplete planning or perhaps in some instances deliberately leading observers 'down the garden path.’ In our opinion the day is rapidly arriving when the quality, logic, practicability and completeness of the planning will make the difference between securing financing or not and, in the cases of existing open pit mines, of the difference between survival and closure.

Jan 1, 1977

By Jida Wu, Zhenqian Wang, Chusheng Liu, Wenqiang Qiu, Mengqi Zou, Wei Zhao

During the dry screening, the hole plugging is a serious problem for most traditional screening equipment sieving the moist fine coal. It would lead to the low preparation efficiency and the low screening efficiency. The flip-flow screen is a new kind of screening equipment by using flip-flow motion of elastic screen surfaces to implement the separation of material. With the remarkable advantages of the extraordinary vibration intensity of screen surface, the hole is difficult to be plugged, and the screening efficiency is improved. In this paper, a kind of centralized forced flip-flow screen (CFFS) was proposed based on the crank rocker mechanism. The flip-flow motion of elastic screen surfaces is achieved by the periodical reversed motion of inner and outer screen boxes driven by crank. The advantages of the CFFS include considerable deformation of the screen surface, stable flip-flow quantity, low working noise, low vibration influence on environment, etc. The principle and construction of the CFFS were introduced, and the modal analysis and harmonic response analysis of key components (the crank and the linkage) were implemented based on finite element method (FEM), respectively. The first six orders of natural frequency and vibration modes were obtained. The maximum equivalent stress and strain under working and resonance frequency were achieved. The results illustrate that the resonance frequency is much higher than the working frequency, and the stress and strain are all within the safe limit of the material. The prototype was manufactured, and the sieving experiment demonstrates that the CFFS perform steadily, and screening efficiency is over 80%. The new feasible method of the dry screening was proposed by the CFFS. The corresponding numerical simulation and the experiment provided a reliable basis for the future promotion of similar product design and research.

Jan 1, 2017

By S. Guo

In this paper, a model for the resin anchor bolt system is developed in which the smooth bar is modeled by using one-dimensional truss elements and the resin annulus is modeled by using axisymmetric elements. These two submodels are combined together and then incorporated into the' existing computer code ROOFBOLT. After this development, all of the components in the resin anchor bolt system including smooth bar, bearing plate and resin annulus can be correctly modeled.

Jan 1, 1995

By H. P. Knudsen

In most open pit gold mines ore waste selection is based on estimates made from blasthole samples. These estimates frequently are biased. While it is true that high grades and "outliers" can induce a bias they may not be the only reason for the persistent bias seen at many mines. This paper focuses on a source of the conditional bias. In this paper it is shown that the poor blasthole sampling can cause a conditional bias in the estimates.

Jan 1, 1991

By W. W. Vaughn

In the technique described and evaluated, detection of mercury is based on the principle of atomic absorption. An analog signal, produced when mercury vapor absorbs ultraviolet light, is converted to digital form and calibrated to mercury concentration. Interferences are eliminated by selectively trapping the mercury on gold. The lower limit of sensitivity, using a 1-gram sample, is 5 parts per billion. A model of the instrument mounted in a station wagon has been tested successfully in the field.

Jan 1, 1964

By Ernest Bohnet

Each mining operation is unique in some aspect ownership; ore body location, size, geometry, grade, mineralogy, hydrology, or geotechnical parameters; or constraints such as environmental regulations. However, all mining operations are alike in one aspect; the prime objective of any mining project is to maximize the return on the investment. This is the golden rule, or in the language of mining, the investor?s law of conservation. A mineral resource, by definition, does not become a minable reserve unless the mineral or minerals can be extracted economically (and legally). The three preceding sections have covered the various types of surface mining options. The choice of the most economic method is dictated primarily by the type of de-posit to be mined, the mining rate, and the physical characteristics of the deposit.

Jan 1, 2008

By W. J. Mahoney

A good quality assurance program at a coal mine or power plant is accurate, timely, and consistent. The quality analysis is accurate due to a complete sampling of the coal stream loaded into the unit train. The sample analysis is accurate because standardized testing procedures are applied. Once the analysis is completed, the results must be communicated to the electric utility in a timely manner. The electric utility needs the results to better manage the coal inventory at the power plants. A quality assurance program can also help the mine deliver a consistent product to the electric utility's power plants. The importance of the three major tenants for a good quality assurance program: accuracy, timeliness and consistency, are based on major changes that are taking place in the electric utility industry.

Jan 1, 1994

By Y. B. He

The effect of the overflow to underflow (O/U) flowrate ratio of a dense medium cyclone on its performance is tested utilizing a 6" dense medium cyclone and density tracers. The results show that the O/U flowrate ratio is clearly correlated with the separation cut point D50, the separation efficiency Ep, the density differential 0, and short circuiting of the cyclone. Within certain limits, a higher O/U ratio results in a better separation efficiency, a higher D50 and an increased density differential. A lower O/U ratio, on the other hand, reduces the cut point shift and density differential. The phenomenon of short circuiting to the underflow, which is especially significant for fine particles, is directly connected with an excessively low O/U ratio.

Jan 1, 1992