Search Documents

By T. M. Klemetti, T. J. Batchler, T. Matthews

From 2013–2017, there were over 1,120 documented injuries, including fourteen fatalities, from ground falls in underground mines in the United States (MSHA 2017). The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. The load-displacement characteristics of an 8-ft x 12-ft area of 8-gauge welded-wire screen were evaluated using a test frame designed for testing multiple load-pull locations. In previous tests, load-pull contact was always in the center of the bolted screen section. In this study, larger pull contact areas are used to simulate roof falls. The information obtained in this and similar studies can be used to better understand the loading behavior and surface control capability of roof screen in underground mines. INTRODUCTION AND BACKGROUND The large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. Previous tests to evaluate the performance characteristics of various types of screen have been conducted by the University of Alberta (Tannant, 2001). In this study, the load-displacement properties of welded-wire, chain-link, and expanded-metal mesh were measured by performing full-scale pull tests. A flat steel plate was pulled through a screen test sample that was bolted to a special test frame while the pulling force and mesh displacement were measured. These tests established the general load-displacement behavior of the screen. Peak load capacities and stiffness were determined for each screen type, showing how welded-wire mesh has a much stiffer initial loading response, whereas chain-link and expanded-metal mesh have large displacement capabilities and exhibit significant post-peak ductility.

Jan 1, 2019

By Eric Lutz

"Great effort has been expended for more than 40 years to improve the workplace safety and health of surface and underground miners across the United States. When looking at the past decade, withstanding the 2010, Upper Big Branch (UBB) disaster that took the lives of 29 miners, this effort has resulted in a generally decreasing trend from 57 fatalities (22 coal; 35 metal/non-metal) in 2005, to 45 (16 coal; 29 m/ nm) in 2014. Through August of this year, there have been 23 mining-related deaths (eight coal; 15 m/nm). These results reflect continued diligence and perseverance on the part of miners that stay true to our legacy; and demonstrate significant investments from mine-site leadership, mining corporations, and state and federal regulators. However, over the past five years there have been an average of 32 fatalities per year, with a low of 36 (2011 and 2012) to a high of 45 (2014). If we know that there will be somewhere between 30 and 50 mining related deaths next year, which of us will volunteer to be counted as one of the numbered? Clearly, we all agree that one fatality is too many; and as evidenced by changes following UBB, deaths in any sector are deaths reflective of all mining across all sectors.The impact of each miner death touches us all. Miner’s deaths are felt deeply by family and friends, most significantly the children; their communities in which they served, supported, and worshiped; and by society that has lost a hardworking, dependable contributor. Further, to take a slightly cynical, but realistic view, miner fatality events impact the financial vitality of mining and contracting companies and broadly diminish investor confidence. Just as important, these events significantly impact our communities and result in negative public perceptions, which ultimately drive regulatory policy and related compliance pressures. This resulting pressure forces operations to broadly address safety and health gaps in very specific ways (i.e., see U.S. Mine Safety and Health Administration (MSHA) regulations regarding lids for trash cans) minimizing a mine site’s opportunities for operational flexibility. To break this cycle that is the operational reality, mining companies are focusing tremendous efforts on fatality prevention and specifically on dedicated investment to prevent multiple fatality events."

Jan 1, 2015

By Mala R. Ciancia

Planned tunnel projects with advanced geotechnical investigations are more frequently being suspended because of changes in funding, politics, or local priorities. Some of these projects are ultimately canceled, some decelerate and stall, some resume after a short pause, and some restart after being mothballed for several years. The restarted project often differs at least slightly from the predecessor project in terms of alignment and design concept. This paper describes approaches to evaluating the quality and completeness of previous geotechnical investigations for a re-activated project, considering technological advances as well as changes in regulatory requirements, contracting approach, and site conditions which may have taken place in the time since the project was suspended.

Jun 13, 2021

By Thomas C. Shrake

The Lomas Bayas copper property is located93 km (58 miles) east of Antofagasta, Region II, Chile (Fig. 1). The deposit was discovered in 1880. The deposit produced intermittently until 1992. Production at Lomas Bayas took place in high-grade veins and breccias mined underground. During 1991, Empresa Minera Mantos Blancos SA (EMMB) optioned the property from Compania Doña Ada SA. Doña Ada maintained the right to continue mining the ores by open-pit and block-caving methods and hauling the ore to its plant located60 km (37 miles) to the north. EMMB conducted exploration and column test programs. On May 9, 1994, Compania Minera Gibraltar Ltda.(CMGL) signed a purchase option agreement to acquire the Lomas Bayas property. CMGL conducted 8,612 m(9,490 ft) of reverse-circulation drilling, 2,028 m (6,650ft) of diamond drilling, a series of metallurgical tests and geologic mapping. The company then decided to exercise its purchase option.

Jan 1, 1996

By Sara Swiokla Korsikas, Toren Olson, Amado Guzman, Yuri O. Zepeda P

Ore agglomeration has been used as part of the heap leaching process for the last 40 years. However, industrial experience shows that the lack of a universal agglomeration standard has limited the benefits of this, otherwise, valuable unit process. The more complex the ore, in terms of the nature and relative abundance of fines (<74 μm), the more important that the agglomeration product satisfies some minimal requirements. This paper presents an agglomeration scale that identifies the quality standards for agglomerates and documents the resulting mechanical, physical, and hydraulic (hydrodynamic) behavior associated with each level on the agglomeration scale. The hydrodynamic properties of an agglomeration product are critical for the proper design of a leaching operation and, as shown in this paper, can be used to select the optimal pretreatment method for a given ore sample. Agglomeration as a unit process not only allows better conditioning of the hydrodynamic behavior of the ore but also creates an opportunity for optimized delivery of reagents to kick-start the leaching process which may ultimately improve the economic performance of leaching. Industrial case data is used to demonstrate the shortfalls associated with low-quality agglomeration and the benefits of improved agglomeration which range from enhanced porous structure (better percolation and drainage characteristics) to better metallurgical response (faster kinetics and higher metal recovery). Proper agglomeration has been used to render otherwise untreatable ores into valuable leaching resources.

Feb 9, 2024

PolyMet Mining is developing the NorthMet property near Duluth, MN. Laboratory investigations have led to the development of the Platsol process to dissolve in one step the base metals (copper and nickel) as well as the gold and platinum group metals (PGM). To complete the prefeasibility study, a fully integrated, 10-day pilot plant trial was undertaken. The trial consisted of high-temperature (>220ºC or >428ºF) pressure oxidation in the presence of 5 to 10 g/L chloride (the Platsol process). This was followed by solid/liquid separation, gold plus PGM recovery from solution, conventional copper solvent extractions/electrowinning (SX/EW) and recycling of the copper raffinate to the autoclave. The concentrate tested during the trial period was a NorthMet bulk flotation concentrate. It assayed 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t (0.041 oz/st) Au, 2.2 g/t (0.064 oz/st) Pt and 9.9 g/t (0.289 oz/st) Pd Laboratory results were confirmed and, with minor adjustments of the laboratory Platsol conditions, the following leach extractions were obtained during the pilot plant trial: 99.6% Cu, 98.9% Ni, 96% Co, 94.6% Pd, 96 % Pt and 89.4 % Au.

Jan 1, 2003

By G. Deschênes

In Part I of the work, gold and silver were shown to be efficiently extracted from Kupol samples using lead nitrate in a cyanide leach system. In Part II, a comparison of the technical and economic merits of a new technology called CELP (CANMET Enhanced Leaching Process) was made with the cyanidation/AVR(Acidification-Volatilization-Recycling) process using 8 metallurgical variability samples as well as a large composite sample which represented initial two years of Kupol mill feed. The composite sample had 33.4 g/t Au and 289 g/t Ag. The metallurgical demonstrated that the CELP produced very similar gold and silver leach extractions compared to the standard Cyanidation /AVR leach conditions at 1/2 the cyanide concentration (1000 ppm NaCN in CELP vs. 2000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton, were approximately the same for the two technologies (total cost of the CELP with the use of Merrill-Crowe at $46.48/ton, with cyanidation/AVR at $46.13/ton). However, the implementation of the CELP would eliminate a capital expenditure of approximately $5 million. Eight variability samples used to confirm the previous results showed that on average the gold and silver leach extractions with the CELP and the feasibility leach conditions were very similar for gold extractions, but 4.6% higher for silver extractions compared to the conventional cyanidation. The decision was made to remove AVR cyanide recovery from the Kupol flowsheet and implement the CELP at Kupol. The ability to use conventional leach equipment with the CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2009

By T. Harrison

Surface coal mines in West Virginia are receiving stringent NPDES discharge limits for total recoverable selenium. With limits in the low parts-per-billion range, selection and implementation of proper sample collection and analytical methods are imperative for quality assurance and control and for consistency in results. Given the typical oxidized form of selenium in the water, the low limits and the large and variable flow rates from the watersheds, end-of-pipe treatment is difficult and cost-prohibitive to implement. Discharge locations in the remote and steep terrain exacerbate the problem. To evaluate options for end-of-pipe treatment at a Patriot Coal Corporation surface mining operation in West Virginia, CH2M HILL performed wastewater characterization for a range of key constituents and selenium species at three outfalls for selection and preliminary sizing of appropriate treatment processes. A preliminary evaluation of base and wet-weather flows was done to understand flow variability considerations for discharges. A conceptual evaluation of technologies to treat selenium to permitted levels was conducted in con-junction with order-of-magnitude life-cycle cost estimates.

Jan 1, 2010

By S. Rideout

The United States Department of the Interior&apos;s Office of Surface Mining (OSM) is responsible for regulating active coal mining and reclaiming abandoned coal mines in the United States. In working with the State government agencies that implement these programs, OSM is building a new approach that moves away from traditional "command and control" regulation and towards an approach that focuses on providing long-term environmental and economic sustainability on lands disturbed by coal mining. This initiative called "Reclaim the Future!" looks to enhance opportunities for economic development, wildlife preservation and enhancement, reforestation, and other beneficial and productive uses of lands disturbed by coal mining. The initiative is also focused on ensuring that the landowners and the local public have significant involvement in determining how best to reclaim mine sites and what post-mining land uses are most appropriate for each individual abandoned mine reclamation project or active mine reclamation. Through the use of the best scientific input in an open, participatory process, OSM hopes to further sustainable development principles for coal mining within the framework of existing United States law.

Jan 1, 2007

By D. J. Bryden, J. W. Oberholzer

In response to the need for enhanced precautionary measures to safeguard mine workers in collieries from the consequences of methane ignitions in a heading, the coal mining industry has ex- pressed the desire for the development and testing of active on board suppression systems. As overseas systems cannot be used directly in the bord and pillar geometry it is necessary to adapt overseas and local technology to suit local mining conditions, as well as to test such developed systems for their compliance with the expressed needs. As the systems have to be tested in a specific roadway configuration, a facility was developed to enable the testing in South Africa. A surface test facility has been established which can be used to develop and test suppression systems on continuous miners and roadheaders. This facility consists of a tunnel wherein compliance tests can be conducted in simulated underground conditions. A number of methane explosion tests have been conducted in the test facility. The explosions conducted varied in CH,/air concentration (7,5 to 9 percent) and volume (26 to 88 m3). At lower concentrations there was a marked reduction in explosion strength and flame speed. Tests carried out with the Explostop system successfully suppressed the propagation of methane ignitions in both scenarios tested.

Jan 1, 1997

By B. C. Paul, R. Q. Honaker, K. Ho

Recent research has shown that froth flotation is not effective at treating fine coals (-28 mesh) containing a large portion of middling particles. Due to their relatively large density differences, middling particles can be separated more efficiently using gravity-based processes. The ability of gravity separators to treat fine particles has been limited by the lack of particle inertia relative to the surface drag forces. However, particle inertia can be enhanced by the application of a centrifugal field. A commercial-scale centrifugal Falcon concentrator capable of treating a mass flow rate of greater than 1 tph continuously has been used to evaluate its feasibility for treating fine coal as an alternative to froth flotation. Tests conducted on a -28 mesh fine coal circuit feed have found the Falcon concentrator to be very effective at cleaning the 28 x 325 mesh size fraction. For an Illinois No. 5 coal sample, the ash content was reduced in the 100 x 325 mesh size fraction from about 18% to 8% while achieving a high combustible recovery value of nearly 97%. In addition, the total sulfur content was substantially decreased from 2.6% to 1.7%. The effects of the critical operating parameters on separation performance have been studied and their values optimized.

Jan 1, 1995

For nearly two decades, MINExpo International has held the title to the biggest show in mining. The 2012 MINExpo is expected to be the biggest yet, with nearly 1,800 exhibitors rolling out the newest equipment and services across 12 halls. From September 24 to 26 in the Las Vegas Convention Center, MINExpo will present the newest in everything from automation and robotics to safety and communications equipment to reclamation services, and much, much more. The last MINExpo, in 2008, had nearly 38,500 visitors. The show?s sponsor, the National Mining Association, expects this year will be even bigger, with more than 40,000 visitors over three days. Twenty talks on the issues facing mining today are scheduled for Tuesday and Wednesday mornings, but the real action will happen out on the floor. That?s where ultra haul trucks big enough to carry as much as 363 t (400 st) of rock will be assembled next to underground loaders able to lift more than 20 t (22 st) in one scoop. Caterpillar, Komatsu, Liebherr, Sandvik, Atlas Copco: all the big names in mining equipment will be there. Their massive earthmoving equipment and mining machines are the centerpiece of the show. Preassembly for the largest pieces begins on August 6, 2012.

Jan 1, 2013

By Paul R. Wieber

This paper describes the U. S. Energy Research and Development Administration&apos;s (ERDA) program to develop in situ coal conversion processes, especially gasification, he potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification independent studies show this process to be 25Z cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the lost advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average pro¬duction rates of 5.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds.

Jan 1, 1977

By Yongjun Peng, Yufan Mu

Pyrite depression in the flotation of copper ores is difficult due to the activation of Cu2+ ions on pyrite surface. In this study, the radical chain reaction involving the redox cycling of Cu(I/II) induced by sodium metabisulphite (MBS) was exploited to selectively depress the flotation of copper-activated pyrite at pH 8.0. Electrochemical measurements revealed that the presence of Cu2+ and O2 was essential to the formation of SO•− 5 through sulphite oxidation, the main entity to convert the activating species Cu(I)S on pyrite to Cu(II)-hydroxide/sulphate, causing deactivation of pyrite. The depression role ofMBS on pyrite flotation was closely associated with the type of grinding media which affected the electrochemical conditions of flotation. When forged steel was used as the grinding media, a high dosage of MBS was required to depress pyrite, but a low dosage of MBS could almost completely depressed pyrite when high chrome steel grinding media was used. This is because high chrome steel produced a stronger oxidation condition with a higher amount of Cu2+ and O2 which promoted the formation of SO•− 5

Jan 26, 2021

By Josef Arnold, Norbert Fuegenschuh

The “Eggequerung” is an important part of the German Railway’s (Deutsche BahnAG) modernized Dortmund—Kassel line. The heart of this 13-km-long (8 miles)construction lot is the double-track Egge Tunnel with a total length of 2,880 m(9,450 ft.). The tunnel was driven using the New Austrian Tunnelling Method (NATM).The construction contract also called for a reinforced concrete secondary lining, guaranteed for a full water pressure of 30 m (100 ft.) water column. Preliminary geological study already showed that very problematic geological-hydrological conditions would have to be expected. This talk describes the chosen NATM driving concept that was adapted to the prevailing geological and hydrological conditions, the special driving method applied in geologically difficult zones as well as the water control concept used during driving. The flexibility and the limits of the NATM under exceptional hydrological conditions are illustrated. Also described are reinforced concrete lining works for the watertight secondary vault (reinforced concrete secondary lining without water-proofing membrane).

Jan 1, 2003

By Evan J. Owen, Virginia T. McLemore

of high specific gravity, resistant minerals that form from mechanical concentration by waves, currents, and winds in marginal-marine environments. These sediments are enriched in critical minerals such as titanium, zirconium, and REE. Cretaceous beach-placer sandstones are found in the Colorado Plateau of northwestern New Mexico. Originally discovered by airborne radiometric surveys for uranium in the 1950s, these beach-placer sandstones are being re-examined with modern methods as potential sources for critical minerals. Selected beach-placer sandstones have been sampled, mapped with ground radiometric surveys, and analyzed with whole-rock and trace element geochemical methods. Mineralogy is being determined with optical methods, XRD, and EMPA. Zircon, rutile, ilmenite, and monazite are the primary heavy minerals of interest found in the studied deposits. Initial results show that the sandstones contain up to 1.4% total REE, 29.4% TiO2, and an estimated 4.9% ZrO2. Chondrite-normalized REE diagrams show distinct light REE and minor heavy REE enrichment, as well as pronounced negative Eu anomalies for each deposit.

Feb 1, 2024

By Akram Marseet, Andrew J. Petruska, Rik Banerjee

Underground mine roof bolting is a crucial operation for miners’ safety and mine sustainability. Since roof bolting is a manual or human-supervised operation, miners’ safety is at risk due to dust or rock falls. Traditional machine learning algorithms have shown limitations to detecting drillable areas, mainly due to harsh lighting conditions. The authors propose an adaptive deep-learning framework for autonomous roof bolting. The proposed framework is based on implementing a binary semantic segmentation algorithm on color images to classify pixels that belong to rock from those that belong to non-rock. Significantly, the proposed framework implements deep learning semantic segmentation on images from traditional and neuromorphic vision sensors in underground mines. The performance of the proposed model shows an impressive accuracy level of at least 98% at a low number of training epochs with smooth learning curves. The high accuracy enables the implementation of autonomous roof bolting, greatly improving miners’ safety and operational efficiency while reducing human exposure to safety hazards. This research will advance the use of deep learning in mining automation and has the potential to revolutionize the traditional mining industry.

Feb 1, 2024

By Isabel F. Barton, MarkD. Barton, Christian A. Rathkopf

Molybdenite is the world’s principal source of rhenium (Re), a critical element in multiple high-tech applications. However, the Re contents in molybdenite vary by orders of magnitude on scales ranging from single grains to whole deposits. In order to better understand the systematics of this variation and what geochemical factors control molybdenite Re concentration, and hence overall Re resources, we examine global patterns in molybdenite Re contents through a compilation of > 3000 measurements of Re in molybdenite from > 700 mainly ore-bearing moderate- to high-temperature hydrothermal systems of different types. Our results are similar to but expand on those of earlier studies. Rhenium concentration in molybdenite has a lognormal distribution and varies systematically with type of geologic system, intrusive lithology, and Mo grade. The lowest-Re molybdenite occurs in greisens (geometric mean 1 ppm ± a multiplicative standard deviation of 9), quartz vein-hosted W-Sn deposits (2 ± 5 ppm), unmineralized granites and granodiorites (12 ± 8 ppm), intrusion-related deposits (24 ± 8 ppm), and porphyry W-Sn deposits (16 ± 11 ppm). Rhenium is most enriched in molybdenites from volcanic sublimates (23,800 ± 5 ppm), with skarn Fe and Au (560 ± 5 ppm and 540 ± 3 ppm respectively) and porphyry Cu and Cu-Au deposits next (470 ± 4 and 430 ± 7 ppm respectively). Among porphyries, skarns, and quartz vein-hosted deposits, Re is most highly concentrated in molybdenites from Cu and Au systems and its concentration decreases systematically through Cu-Mo, Mo, Sn, and W deposits. In nearly all cases, molybdenites from systems associated with intermediate igneous rocks contain more Re than molybdenites from systems of the same type with more felsic rock associations. The disparity between Re contents of molybdenite in felsic and intermediate systems is largest for porphyries, quartz vein-hosted, and skarn deposits and is near zero for subeconomic or barren granite and granodiorite Mo systems; felsic intrusion-related deposits have slightly higher molybdenite Re than their equivalents associated with intermediate intrusions. In most systems, molybdenite Re content does not correlate with metal grade, but may have an inverse correlation with Au grade in intrusion-related deposits (based on a small number of data points) and does exhibit a strong inverse correlation with deposit Mo grade. Dilution of Re through larger amounts (higher deposit grades) of molybdenite explains about 40% of this correlation, but the relative enrichment of Re in molybdenite from low-Mo deposits must also reflect some selective enrichment of Re/Mo in porphyry Cu systems compared to porphyry Mo systems. We found no evidence for secular increase or other systematic temporal variation in molybdenite Re content. The data regarding the use of molybdenite Re content as a proxy for mantle influence are ambiguous. Nearly all observed empirical correlations can be traced back to differences in redox state and sulfide concentration, the two geochemical factors identified here and by previous experimental work as the controlling influences on Re mobility under hydrothermal conditions. Hydrothermal systems with reducing conditions (W- and Sn-rich) tend to have low molybdenite Re even though compiled whole-rock data indicate that their source rocks have as much or more Re as those of more oxidized systems (e.g., Cu-rich). Vapor-phase exsolution, crustal assimilation, and mixing with external fluids may all enrich molybdenite Re concentrations in individual deposits and deposit types, but their extent and importance in overall hydrothermal concentration of Re is uncertain. Thus, it appears that the available molybdenite Re resource in an ore deposit largely depends on how the deposit’s redox and sulfidation conditions have varied over time and space during the timespan of hydrothermal activity. Oxidized, high-sulfide conditions tend to concentrate Re in molybdenite, whereas reducing conditions tend to leave Re dispersed at low concentrations in the bulk rock.

By F. D. Fox

Abandoned mill tailings deposits can be found scattered throughout the Northern Black Hills of South Dakota, indicative of past mining activities that originated during the great gold [ERRATA SHEET RESTORATION OF GOLD MILL TAILINGS, BLACK HILL, SOUTH DAKOTA 84-119 F. D. Fox Under subtitle Prospects Related to Present and Future Tailings Disposal Practices, include reference No. 12 in paragraph seven after "construction of the Grizzly Gulch tailings disposal project,"12 Reference 12 should read: Jeffries, Lawrence F. and Tczap, Andrew, "Homestake&apos;s Grizzly Gulch Tailings Disposal Project," paper presented at 1978 International Mining Show, October 11, 1978.]

Jan 1, 1984

By D. Scott Barr

The Zarafshan/Newmont Joint Venture operates the Muruntau heap leach project, located in the Kyzylkum desert of central Uzbekistan. The mine produces more than 12.4 t/a (400,000 oz/year) of gold from low-grade oxide ore stockpiles adjacent to the Muruntau open pit. It is op¬erated by the Navoi Mining and Metallurgical Combine and is one of the largest gold resources known (Fig. 1). Since commissioning in 1995, total heap leach production has exceeded 21 t (675,000 oz). The joint venture uses four-stage crushing and screening to produce a final product for heap leaching, Merrill-Crowe processing and local refining.

Jan 1, 1998