Search Documents

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

By Martin Langenderfer, Catherine Johnson, Alexander Douglas

Mine haul roads degrade rapidly due to extreme loads on sub-optimal construction materials. Unmanned aerial vehicles (UAV) are suited to quantify large-area road-network conditions, such as surface roughness, defects, and grade to optimize remediation of poor conditions and reduce overall costs. Mine haul roads present unique challenges, such as material type and edge characteristics, to automatic road detection that often fail, requiring manual road input. This research proposes a new method for analysis using the road center determined by principal curve analysis of a haul truck’s Global Navigation Satellite System (GNSS) traces; analysis grids were created from this center line. A dense point cloud from UAV photogrammetry was generated, and multiple linear regression analysis was conducted on each individual grid. The root mean square error in each grid indicates the surface roughness, and the change of slope between grids indicates the road grade inconsistencies. This method was applied to 26 road sections, and the results were validated by images taken from the truck operator’s vantage point. Critical defects were identified including excessive pothole formation, corrugation, depressions retaining water, and narrowing of travel lane. The results demonstrate this is a valid method of road identification and quantification of road defects at a mine site.

Dec 19, 2023

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The forestry reclamation approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22 m (4 ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes (i.e., greater than 23°) could lead to slope failures, which is one of the issues that the Surface Mining Control and Reclamation Act of 1977 (SMCRA) sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. During this first phase of investigation, there has been no major mass movement of the slope and slope stability analysis indicates that the application of the FRA has little impact on the overall stability of the slope. Mining Engineering, 2011, Vol. 63, No. 12, pp. 55-62. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Daniel M. Flanagan

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Joe Garska, member SME, of Imerys, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Lin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Adam Rodriquez, member SME, of Penn State, construction aggregates.• LeDeana Roberts, member SME, of Imerys, fillers and pigments.• Harsha Kolla, member SME, of ChemEOR, sorbents, filters and process aids.• Edgar Blanco, member SME, of FLSmidth, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.During the past 25 years, U.S. ball clay production (the quantity sold or used by domestic producers) increased from 788 kt (869,000 st) in 1990 to an alltime high of 1.31 Mt (1.44 million st) in 2003 (Fig. 1). Housing construction within the United States, a leading market for ball clay-based ceramics and sanitaryware, began to decline in 2005, which resulted in a considerable decrease in sales of ball clay that continued through the 2008-2009 economic recession. After bottoming out at 831 kt (916,000 st) in 2009, ball clay production steadily increased through 2015 (Fig. 1). Estimated sales in 2015 were 36 percent higher than those in 1990 and 18 percent lower than those in 2003.Four companies (H.C. Spinks Clay Co., Imerys S.A., Old Hickory Clay Co., and Unimin Corp.), mined ball clay in five states during 2015. An estimated 1.7 Mt (1.18 million st) of ball clay valued at an estimated $47.5 million was sold or used by U.S. producers, a 4-percent increase from 1.03 Mt (1.14 million st) valued at $45.2 million in 2014. Approximately 65 percent of total ball clay production was air-float, 25 percent was crude or shredded and 10 percent was water-slurried"

Jul 1, 2016

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By W. A. Wright

The use and abuse of social media restate common employee relations issues. Business solutions to these issues require advanced preparation. Employers should establish and enforce social media policies to guide their reactions to employees? social media posts that reflect on the employer and its business.

Jan 1, 2011

By N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities for the year 2016 draws upon information from industry sources, published literature, SNL Metals & Mining (SNL), an offering of S&P Global Market Intelligence (New York, NY), and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. Three types of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. dollars provided by SNL; 2) regional and site-specific exploration activities that took place in 2016 as compiled by the USGS and 3) regional events and legislation that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources were used to develop commodity and regional compilations, statistics may vary depending on the source and type of data that are being reported. The SNL data summarize budget estimates for worldwide exploration activities in 2016 for 30 nonfuel mineral commodities and metal alloys, based on company surveys. Surveys focused on precious metals (gold, platinumgroup platinumgroup metals (PGMs) and silver), base metals, (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (bauxite, chromite, iron ore, manganese, phosphate and potash) and other commodities (aluminum, antimony, diamond, graphite, heavy-mineral sands, lithium, niobium, rare-earth elements (REEs), scandium, tantalum, tungsten, uranium, vanadium and yttrium). Information on uranium exploration activities was included in SNL’s survey for the first time in 2007. Data on lithium, niobium, phosphate, potash, REE and tungsten were compiled for the first time in 2010, and scandium, vanadium and yttrium were added in 2014 because of their increased topical significance. Since 1999, companies with exploration budgets of $100,000 and greater were included in the SNL surveys. SNL budget estimates exclude coal, and oil and gas. The 2016 SNL mining company survey compilation was reported by SNL to include an estimated 95 percent of the world’s nonfuel mineral exploration budgets. The 5 percent that was not covered was accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data and government-funded exploration activities."

Jan 5, 2017

By Daniel F. Meyer

INTRODUCTION The Metropolitan Boston Transit Authority (MIA) Red Line has served greater Boston commuter needs from its Harvard Square terminus since its opening in 1912. Since then, the population of Boston's northwest area has increased substantially, and with this growth have come dramatic changes in the type and distribution of urban land uses, including the number of households, jobs, shopping and recreational opportunities; these changes have created a need for improved transportation. Extension of the Red Line to better serve these communities has been a topic of discussion for nearly 40 years. In November of 1977, the Urban Mass Transportation Administration (UMTA) granted the MBTA approval and funding for the Red Line Extension Project. With funding in place, the MBTA proceeded with final engineering and construction of the section from Harvard Square to Alewife. When completed, the Red Line Extension will add 3.2 miles of new track to the MBTA system. Estimated final cost is about $400 million. On October 3, 1978, the MBTA received bids for the construction of Project 091-105, Harvard Square to Porter Square Tunnels and Shafts, which is part of the overall Red Line Extension. The Joint Venture of Morrison-Knudsen, White, Mergentime was the low bidder at $47,478,600. Official award of the contract came on October 25, 1978, with Notice to Proceed given October 31, 1978. The contract called for construction of two independent parallel concrete-lined tunnels in rock, soft-ground and mixed-face

Jan 1, 1983

By Hai Lin, Renshu Yang, Yongliang Li, Shizheng Fang

With the aim of solving the large deformation problem of surrounding rock in coal mine roadways with a thin sand-mudstone interbed roof, transportation roadway 1603 in Haoyuan Mine was considered. The failure mechanism of surrounding rock was studied through comprehensive on-site investigations, borehole image analysis, mineral composition analysis, and other means. Numerical simulations were performed to determine the influence of roof layer thickness, lateral pressure coefficient, and coal rib strength on the stability of the interbedded roof. The main reasons for support failure and deformation of the roadway are softening and swelling of the sand-mudstone interbed roof upon exposure to water, insufficient support capacity of the roof due to the soft coal rib, an unreasonable support scheme, or poor construction quality, which can reduce the bearing capacity of surrounding rock. Based on our analysis, a control strategy was devised for a thin coal-mudstone interbed roof. The support scheme combines long and short cable support, strengthening of the coal rib to consolidate the roof, and partially shotcrete grout, and was found to improve the overall mechanical strength of surrounding rock and maintain the stability of the thin sand-mudstone interbed roof. The results of the numerical simulations and monitoring data indicated that the proposed support scheme effectively controls the deformation of the surrounding rock of thin sand-mudstone interbed roof of coal mine roadways while maintaining the safety and stability of the surrounding rock and supporting structure.

Dec 12, 2022

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By Omid Asghari, Amin Mousavi, Arshad Ranjbar

Geometallurgical modeling of the production benches is an attempt to estimate the geometallurgical variables of the different ore domains, which leads to a better understanding of the ore and its properties. Having geometallurgical variables results in a more accurate prediction of ore characteristics, an improved drilling and blasting operation, and better efficiency of the processing plant. In this research, the geometallurgical variables required for the geometallurgical modeling of the extraction benches are discussed. Then, the relations between Bond work index (BWi), as one of the most important geometallurgical variables and the primary grindability index, and rock geomechanical properties are investigated based on the previously published studies. The BWi is the main parameter for measuring the resistance to the grinding of ore minerals. It represents the energy required for processing (e.g., crushing, grinding) ore rocks in the beneficiation plant. As a real case study, BWi of a production bench in Sungun Copper Mine, located in East Azarbaijan province, Iran, was estimated. The rock’s geomechanical properties were measured using laboratory tests, including uniaxial compressive strength, Brazilian tensile strength, point load strength, and hardness. Then, BWi was estimated using the proposed formulas in the literature and the results of the rock’s geomechanical properties. The selected bench consists of three ore zones and two dyke domains. The laboratory tests revealed that the first ore zone has a slightly higher compressive strength than the other two zones, while the compressive strength of the waste rocks is larger than the ore domains. Using the proposed equations in the literature, the predicted values of the BWi for the samples in ore zones are in the range of 6.36 – 14.44 (kWh/t), and therefore this wide range must be considered when the short-term production schedule is planned. In addition, variations are observed in the samples within a specific zone and between the ore zones, demonstrating heterogeneity in the selected bench. Finally, wide-open results obtained by different equations show a necessity to perform a geometallurgical program specifically for the Sungun mine.

Oct 28, 2021

At the Prospectors and Developers Annual Convention (PDAC) in Toronto, Canada mining and exploration companies of all sizes were on hand to discuss the year that was and those that will be. The following is a look at some of the companies with Canadian operations that were on hand for PDAC 2009. Iamgold Corporation is a leading mid-tier gold mining company producing approximately 31 t (1 million oz) of gold from seven mines on three continents. With record revenues of $870 million ? up 28 percent when compared to 2007 ? the company is focused on growth with a target to reach 56 t (1.8 million oz) gold production by 2012. During 2008, the company acquired the Essakane project in West Africa. The project is fully permitted, under construction and will contribute more than 9.3 t (300,000 oz) of lower cost production by late 2008. Iamgold increased its reserves by 55 percent, to 385 t (12.4 million oz) and its resources in-creased by 16 percent to 821 t (26.4 million oz) in 2008. Going forward, Iamgold has three areas of focus ? West Africa, Guyana Shield and Quebec ? with seven gold operations, five advanced projects and the Niobec niobium mine included. The Rosebel Mine in Suriname is Iamgold?s fl agship property. With measured and indicated resources of 300 t (9.6 million oz), it accounts for 30 percent of Iamgold?s production. Production there was up 20 percent compared with 2007 and further production increases are expected in 2009 and 2010. Mill expansion and optimization increased throughput from 8.9 Mt/a (9.8 million st) to 10 Mt/a (11 million stpy). In West Africa, Iamgold has joint ventures at Sadiola in Mali; Tarkwa in Ghana; Yatela in Mali and Daman in Ghana. Iamgold also has 100 percent ownership of the Mupane gold mine in Botswana and the Doyon gold mine in Quebec, Canada. Also in Quebec, Iamgold has 100 per-cent ownership of the Niobec niobium mine in Quebec. Niobium is used in high strength specialty steels.

Jan 1, 2009

By Arash Habibi, Anna Cable, David Loring, Aleksandar D. Bugarski, Logan Ingalls, Calvin Rutter

The results of diesel particulate matter (DPM) monitoring were used by the underground mining industry to mitigate adverse effects of exposure to DPM. NIOSH Method 5040, currently used for ambient and personal exposure monitoring, does not provide needed real-time information. The objective of this study is to develop a methodology for continuous monitoring of DPM concentrations in an underground environment, founded on the application of the Dekati electrical particle sensor (DePS). The DePS, which measures concentrations of submicron aerosol in real time using a diffusion-charging sensor, was evaluated by comparing the results of the concurrent measurements with reference methods at several locations downstream of the diesel-powered equipment. The DePS results were found to correlate well to those obtained by reference methods. However, it was found that dependence of the response on the physical and chemical properties of aerosols necessitates sitespecific correlation factors for the targeted matrices. The site-specific factors for number and mass of diesel aerosols were derived using the results of concurrent measurements with TSI NanoScan, FLIR Airtec, and carbon analyses performed on the concurrently collected filter samples. The results showed that methodology based on compensated DePS measurements would be suitable for continuous monitoring of DPM in underground mining operations.

Dec 1, 2022

By A. Bieg, M. Samson, Z. Bell, A. Zinsser, J. Schuyler

As the world progresses toward the renewable energy transition, the demand for minerals increases exponentially. According to the International Energy Agency (IEA) 2021 Net Zero by 2050 Report, critical mineral production needs to grow six times to combat climate change. It’s estimated that four to seven percent of global greenhouse gas (GHG) emissions come from the mining sector’s Scope 1 and 2 (direct and indirect) emissions. Including Scope 3 (upstream, downstream, and embedded) emissions, the sector accounts for 28% of global GHG emissions. In a typical mining operation, diesel fuel is the biggest source of direct GHG emissions, and haulage is often the main source of diesel emissions. Large haul trucks have been the industry standard for over 50 years and offer flexibility, relatively low capital cost (especially with equipment lease options), and guaranteed technology with known maintenance. The challenge will be to justify their continued use when there are more economical options that lead to significant reductions in GHG emissions. The purpose of this study is to compare five haulage options in terms of GHG emissions, using the methodology defined by the Greenhouse Gas Protocol Scopes 1, 2, and 3 (Category 2). Additionally, this analysis compares operating and capital costs associated with the five haulage options (emerging and proven technologies): 1) Diesel-Electric Haul Trucks, 2) Battery-Electric Haul Trucks, 3) Fuel Cell Haul Trucks, 4) Railveyor, and 5) Conveyor. This analysis looks at the emissions and costs associated with operating the equipment (fuel and electricity), the embedded emissions and costs associated with the construction and installation of the equipment itself, and the associated infrastructure (roads, powerlines, and rail).

Feb 1, 2023

Introduction Aggregate mining impacts on water resources are a source of concern to local governments. To evaluate those impacts, the Minnesota Department of Natural Resources conducted a four-year study at three gravel pits (two alluvial and one beach-ridge) and five quarries (flat-lying Paleozoic limestone). This research provides the first comprehensive look at aggregate mining impacts on ground-water systems in Minnesota. The results will be used by government officials making permitting decisions about aggregate operations and by responsible owners of aggregate mines as they plan their operations to avoid conflicts with neighbors and with resources dependent on ground water and surface water. Natural aggregate (crushed stone, sand, and gravel) is a vital part of our economic infrastructure in Minnesota. Aggregate is used for road and bridge construction and in a variety of building materials. In 2003, the value of construction sand and gravel and crushed stone in Minnesota was approximately $245,000,000. As Minnesota’s economy continues to expand, the demand for aggregate will continue to grow. Sand and gravel pits are located in every county in Minnesota. In 1990, the Minnesota Department of Natural Resources, Division of Minerals (DNR Minerals), estimated the number of active and inactive operations at 1500 with the view that this number was likely too low. Quarries for mining limestone, dolomite, sandstone, and hard rock (granite and quartzite) are found in 34 counties. A 1990 DNR Minerals inventory found 165 active operations, 88 percent of which were limestone quarries (Nelson and others, 1990). That same inventory counted 1,367 inactive operations, 70 percent of which were limestone quarries. Aggregate mining is an extractive use of resources: mining alters the landscape and its natural hydrologic system. When a new pit or quarry is proposed or when an existing operation needs to expand, local governments and citizens typically have many questions about the impacts mining might have. Local governments, which are responsible for reviewing these operations, rarely have the budgets to hire experts to evaluate potential impacts of quarry and gravel pit proposals. The Minnesota Legislature’s Aggregate Resources Task Force identified that local government units (LGUs) often lack the expertise to assess ground-water models (Southwick and others, 2000).

Jan 1, 2007

By Ken Goering, Steve Kral, William Gleason

"Once every four years, the global mining industry gathers in Las Vegas, NV for MINExpo International. According to the show’s organizer, The National Mining Association (NMA), about 44,000 people attended the three-day show from Sept. 26-29. It was a show that featured the latest and greatest in equipment and technology. It also served as the backdrop for a snapshot of the state of the industry and while the picture of a global industry is never completely clear at any one time, one thing that is evident is technology has become a major force in the way mining is done.Had it not been for the awe-inspiring “iron” that was on the show floor in the form of haul trucks and shovels weighing hundreds of tons, one could be forgiven for thinking that they were at the Consumer Electronics Show. From training simulators designed to give a realistic experience of operating mining equipment to virtual reality technology that can take the user into the depths of an underground mine or the middle of a mapped ore deposit, an overriding theme of MINExpo 2016 was that the mining industry is connected like never before.In the north hall of the Las Vegas Convention Center was the GE Mining booth that was designed to showcase its efforts to help create a mine that will be connected from the front office to the face of the underground wall or bottom of the openpit. GE Mining called its booth a digital mine, and it included a suite of technologies that can improve performance, reliability, safety and operations. GE Mining said it views each mine as a mini-city, requiring power, water and transportation. Intelligent, real-time monitoring across the mine allows operators to make data-driven decisions that improve equipment reliability and optimize mine operations for substantial savings. And GE Mining was just one of many exhibitors showing off software that allows various types of equipment to communicate. Its booth sat in the shadow of the Komatsu booth with its new 360-t (400-st) 980E-4 haul truck that included GE’s 360-t (400-st) electric wheel motor. This is just one example of how technology is connecting machines, operations and people around the world and how mining is moving forward."

Dec 1, 2016

By Todd Minoski, KRISTIN FLOYD, Michael Murphy, VASU GANGRADE, Gamal Rashed, DYKE MARK VAN, Brent Slaker

Underground stone mines frequently operate on multiple mining horizons or are required to undermine or overmine old workings. In these situations, the effects of pillar columnization and interburden thickness on the stresses surrounding mine workings are poorly understood. Many old workings were not designed to consider the effect on future undermining or overmining and, as a result, are laid out on irregular patterns and with pillar sizes that are difficult or impossible to replicate on adjacent levels. Additionally, as depth increases, even a consistent gridded mine layout may result in poor columnization due to the need to increase pillar sizes. Rules of thumb and past practice for designing multiple levels may often be effective. This paper explores the effect that multiple-level stone mining has on stress redistribution through the discussion of two case-study mines and associated numerical modeling to provide additional insight into situations which may cause concern.

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Peter Haller

Introduction The impact of the Comprehensive Environmental Response, Compensation, and Liability Act, or Superfund, as well as the Resource Conservation and Recovery Act (RCRA) and their state counterparts underscore the intention of the nation's lawmakers to reduce the risk from hazardous substance to American society. The promises and requirements embodied in these laws, together with their prospects for liability, will continue to have a very substantial impact on decision making in the mining industry. These laws present the prospects for staggering liabilities, often of an unquantifiable nature in terms of time and amount. It is therefore necessary to keep them in clear focus. This is particularly true in light of President Reagan's signing into law the Superfund amendments on Oct. 17, 1986, and in light of the Environmental Protection Agency's (EPA) major policy pronouncement of July 3, 1986, regarding solid wastes from extraction of ores and minerals. This article examines the general trends as well as the specific provisions of these laws in an effort to assess the prospects of liability for the mining industry of releases of hazardous substances into the environment. Hazardous substances vs. hazardous wastes The distinction between the terms "hazardous substances" and "hazardous wastes" is important to appreciate for the purposes of assessing the potential for liability for a mining operation. Hazardous substance is a term that appears in and is defined in the Superfund Act. In Superfund, it is defined by reference to other substances that have been declared to be hazardous under other federal environmental statutes, such as RCRA, the Clean Air Act, and the Clean Water Act. Hazardous waste is a term that is less all-encompassing than hazardous substance, as that term is defined by RCRA. Hazardous substances do not need to be wastes to be considered hazardous for the purpose of Superfund liability. A "release" of a hazardous substance into the environment can bring about potential liability under Superfund. Many mining wastes, even though they are not considered hazardous wastes by EPA under RCRA, have been determined by that agency to be capable of bringing about liability under Superfund if they contain chemical substances, such as the heavy metals copper, lead, mercury, zinc, silver, and others. Therefore, it is not sufficient for the mining industry to be able to answer whether one has hazardous waste at a mining site. That question only goes partway in addressing the potential for liability. The next question is, do one's solid or liquid mining wastes contain hazardous substances that could bring about liability under Superfund? Superfund 1980 law: A review Some provisions of Superfund as it existed before its recent amendments must be considered. The law provides that the owners and operators of mining sites, together with those who transport hazardous substances to such sites, can be held jointly and severally liable for the cost of cleaning up the site. The concept of joint and several liability means that one party, as among many, can be held totally responsible for the costs of cleanup. This is particularly true where the harm done by many parties to the envi-

Jan 2, 1987