Search Documents

By Matthew E. MacGregor, Hugh T. Kelly

I.H. 635 (LBJ Freeway) was constructed as a loop freeway around the city of Dallas in the late 1960s and early 1970s with a design capacity of 160,000 vehicles per day (vpd). Today’s facility is carrying over 270,000 vpd. To help mitigate community concerns with regard to right-of-way issues, noise, safety, and traffic disruption, the Texas Department of Transportation (TxDOT) is planning a number of significant improvements. The West Section improvements include the construction of managed HOV/Toll lanes. Within this 8-mile section, TxDOT is planning two mined tunnels(1.5 and 1.9 miles long) beneath the LBJ Freeway. The mined tunnels will connect to cut-and-cover box sections in both the east and west directions. This paper presents an overview of the project development from the design schematic, through the geotechnical investigations, into the current design stage. The project is being planned for implementation by use of a Comprehensive Development Agreement.

Jan 1, 2005

By Jon J. Indall

I. INTRODUCTION The challenge of moving the use of nuclear energy from military to civilian use was first issued by President Dwight Eisenhower in his December 8, 1953 “Atoms for Peace” speech delivered at the United Nations. Eisenhower stated: “The United States knows that if the fearful trend of atomic military build up can be reversed, this greatest of destructive forces can be developed into a great boon, for the benefit of all mankind. * * * * The more important responsibility of this Atomic Energy Agency would be to devise methods whereby this fissionable material would be allocated to serve the peaceful pursuits of mankind. Experts would be mobilized to apply atomic energy to the needs of agriculture, medicine, and other peaceful activities. A special purpose would be to provide abundant electrical energy in the power-starved areas of the world. In the 1950’s and 1960’s, the Atomic Energy Commission promoted the use of nuclear power as the answer to our nation’s energy problems. Nuclear power would provide energy too cheap to meter. The utility industry responded and numerous plants were planned with over one hundred constructed from the 1970’s to the 1990’s. Capital costs for nuclear power plants escalated due to permitting changes and public opposition, and the Three Mile Island incident caused new nuclear plant construction to cease. Today, we once again are experiencing a nuclear renaissance. Concerns over global warming and rapid projected increases in the demand for electricity have caused many nations to begin construction of new nuclear fleets. The price of uranium to fuel these reactors, which had dropped to an historical low of $7.10 in 2001, has surged to $56.00 as of October 2006. This paper will review some of the social, environmental, and government issues that are all playing a role in the resurgence of the nuclear fuel industry.

Jan 1, 2007

By Wolfgang Guetter, Wolfgang Weber

The upgrading project for two hydropower plants in Slovenia, Europe, requires two new pressure tunnels: Plave II (5.9 km Flysch) and Doblar II (3.6 km Limestone). It is the worldwide largest application of the Double-Shield TBM technology combined with an extremely thin-walled monoshell honeycomb lining system. The first drive has been completed by end of June 2000 achieving best performances of 50m/d and almost 1,100m/mth. In September 2000 the TBM started the second tunnel without any required adjustments due to geological or other reasons. Another 52m/d have been bored already within one production day of two 8 h shifts achieving a maximum penetration rate of more than 6m/h. The completion of the Doblar drive can be expected by February 2001.

Jan 1, 2001

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining health and safety of miners. The authors evaluate potential real-time monitoring solutions for detecting and reducing diesel particulatematter, mine fires, and dust in situ, and examined the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limit. Authors review relevant documents, including research papers, trade publications, and manufacturers’ website-based information, to identify research gaps. The authors also evaluate contemporary sensors (airflow, gas, dust, silica), control system and software technologies, data transport systems, Industrial Internet of Things, ventilation network simulators, and control devices to identify potential health and safety research gaps. In this study, examples of some mines from Canada, Australia, and the USA are included where ventilation monitoring and controls have been applied. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

May 12, 2020

By K. Kohli

A case study involving a historic structure undermined by longwall mining is presented in this paper. The location of this study is in South Western-Pennsylvania; USA. The structure is 150-years old and subsided 4.5 feet. This paper discusses the mitigation measures taken to reduce the subsidence damage and its effectiveness.

Jan 1, 2002

By F. Hassan, M. A. Arafa

At El-Gedida iron ore deposits there is a block of about 30million tons neglected due to its higher sulfur content due to the presence of barite gangue minerals. From this bluk by magnetic separation dual concentrates of high grade iron concentrate (~65%Fe and total Sulfur of 0.26%) and the second concentrate is barite of (60.87% BaO and total impurities of less than 3%).

Jan 1, 1999

By Marcus A. Wiley, Gregory Abramov

Borehole mining (BHM) is a remotely operated method of extracting rock material through boreholes by high-pressure water jets. Figure 1 illustrates a BHM tool and fluids circulation. The tool consists of at least two pipes, one for pumping down high-pressure water, the second for delivering slurry to the surface. This article reviews the BHM process. It discusses current and new applications for borehole mining and help the readers determine if BHM is applicable in their situations. Previous articles in ME about BHM explained either a particular project (ME, April 2001, pp. 33-36) or a newest patent in this area (ME, March 1991, pp. 313-318). However, neither one provided an overview on the modern BHM technology.

Jan 1, 2004

By Eldon L. Abbott, Rebecca K. Bolan

The Florida Department of Transportation, Florida’s Turnpike Enterprise is studying the feasibility of a 1128 meter (3,700 foot) vehicular tunnel to provide direct access for Port of Miami traffic to/from I-395, I-95, SR-836 (Dolphin Expressway) and Miami International Airport. Both Bored and Immersed Tube tunnels were evaluated and re-evaluated for constructing two, two-lane, 11.9 meter (39-foot) diameter tunnels beneath the Main Shipping Channel lying between Watson Island and the Port of Miami on Dodge Island in Biscayne Bay, Miami, Florida, USA. Bedrock Geology of South Florida is predominately very permeable, vuggy limestone with sand seams and occasional voids. Groundwater inflows in deep cut-and-cover excavations, tunnel buoyancy, grouting, maintenance of Port operations and potential/possible environmental impacts to Biscayne Bay were significant issues.

Jan 1, 2005

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

By Yehia M. Youssef, Nourhan Moukhtar, M. H. Abdel-Aziz, Ibrahim Hassan

Copper was recovered from copper sulfate solution in a batch-recycled galvanic reactor operated under forced convection with the generation of electrical energy during the cementation process. The divided galvanic cell consisted of parallel copper and zinc plates. The mass transfer rate and the amount of electrical energy generated were found to be directly proportional to the solution flow rate and the initial concentration of metallic ions and inversely proportional to the distance between electrodes. The experimental results were expressed in terms of a dimensionless correlation including all parameters. The wastewater treatment presented herein cell can be utilized to recover many soluble heavy metal ions from solution with high efficiency.

Oct 2, 2020

By A. B. Cecala, G. W. Klinowski

Introduction The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour (acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec (50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average millwide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al., 1987). Testing Total mill ventilation systems were evaluated at two processing operations. For both tests, the primary goal was to determine the reduction in respirable dust throughout the structure. Test site No. 1. The first evaluation was performed at a clay-crushing and screening mill in New York. The mill's base dimensions were 39.6 x 9.8 m (130 x 32 ft), giving a volumetric capacity of 4250 m3 (150,000 cu ft). The TMVS was designed to provide 12 m3/sec (25,430 cfm) of ventilation air to the mill, representing about 10 acph. This was accomplished by three 4 m3/sec (8475 cfm) roof-powered exhaustors that were evenly spaced across the roof. Three wall louvers provided inlets for make-up air at the mill's base. Two evaluations were performed at this mill. The first occurred for two days in December when outside air temperatures ranged from -12.2° to 4.4° C (10° to 40° F). Temperatures with the wind chill factor dropped as low as -34° to -40° C (-29 to -40° F) during the early morning. The second evaluation was in April when outside air temperatures ranged between 10° to 26.7° C (50° to 80° F). These two evaluations verified the effectiveness of TMVS in lowering respirable-dust concentrations throughout the mill. Gravimetric-sampler respirable-dust concentrations in December ranged from 0.22 to 2.39 mg/m3 under normal conditions, compared to 0.13 to 1.55 mg/m3 with TMVS. In April, respirable dust concentrations ranged from 0.29 to 4.84 mg/m3 under normal conditions compared to 0.21 to 2.37 mg/m3 with the system on. TMVS also increased visibility throughout the mill building. Dust reductions for gravimetric and RAM-I instruments are listed in Table 1. Each value was determined by comparing the average concentration for the entire day of testing for normal and TMVS values. The mean/standard deviation values for gravimetric and RAM-1 results were 42.5/17.6 and 37.1/16.8, respectively.

Jan 1, 1996

By Robert C. Speck

The U.S. coal industry has long utilized the pillar-extraction mining technique as a method for maximizing coal recovery. Like longwall mining, it causes large-scale movements that progressively propagate from mine-level to the ground surface and may affect the groundwater regime, surface drainage and surface structures. The U.S. Department of Energy, in an effort to foster in- creased use of total extraction mining techniques, has recognized the need for a better understanding of these movements that will lead to a greater compatibility between coal mining and present and future land use. As part of that goal, GAI Consultants, Inc. is currently in- stalling instrumentation to monitor the ground movements associated with pillar extraction mining at Kitt Energy Corporation's No. 1 mine in northern West Virginia.

Jan 1, 1982

By M. Z. A. Bakar

A series of full scale laboratory linear rock cutting tests was carried out with a long bladed single disc cutter (292 mm diameter, 11mm wide constant cross-section blade) on dry and water saturated sandstone blocks using a linear rock cutting machine (LRCM). The muck collected from the cutting tests has been analyzed to establish a link with the specific energy (SE) of the operation. Coarseness index (CI), a non dimensional parameter, has been found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n is observed between SE and CI with very high CI usually corresponding with the lowest values of SE. The power n of the relationship for both dry and saturated rock tests is much less than the values found in the previous studies using constant cross section disc cutters and is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI is found to be lower for saturated rock than for dry rock, at the same time saturated rock cutting is found to be less energy intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By Dale Matthews

The Getchell Mine, near Winnemucca, NR, was discovered in the 1930s and was initially mined to recover gold from oxide ores. During the 1940s and 1950s, gold was recovered from the highly refractory arsenic sulfide ores using horizontal kilns to roast the ores. During the 1960s, fluid bed roasters were used to oxidize the ore and recover the gold. The mine was shut down from 1968 through 1985. In 1985, heap leaching was started on the low-grade oxide ores that were available. In 1989, a pressure oxidation circuit was started to recover gold from the higher grade sulfide ores. Flowsheet The basic plant flowsheet of the Getchell Mine are shown in Figs. 1 and 2. The plant was designed to process a nominal 2.7 kt/d (3000 stpd) of ore with about an 85% onstream availability and a gold production of 15.5 kg/d (500 oz/ day). Run-of-mine (ROM) ore is fed directly to a wet semiautogenuous grinding (SAG) mill after the +457-µm (+18in.) rock is removed on a stationary grizzly. From the SAG mill, the ore goes to a ball mill where it is ground to 80% -75 µm (-200 mesh) and is then sent to a thickener. The SAG and ball mill operate in closed circuit using cyclones.

Jan 1, 1994

By C. Özgen Karacan

The formation of the gas emission zone in longwall mining and the potential amount of gas in this zone are factors of local geology and spatial variability within this geology. Therefore, geostatistical methods can be used for modeling and prediction of gas amounts and for assessing its uncertainty in the gas emission zone of longwall mines. This study used core data obtained from 64 exploration boreholes drilled from the surface to the bottom of the Pittsburgh coal seam in a mining district in the Northern Appalachian basin. After identifying important coal layers for the gas emission zone, semivariogram modeling was conducted for different coal seams to define the distribution and continuity of various attributes. Sequential simulations were performed for stochastic assessment of these attributes to calculate gas-in-place (GIP) in each coal seam. GIP calculations for coals of various gas emissions zones were combined and ranked for their cumulative distribution function to find GIP in the caved zone and in the fractured zone at the 5%, 50%, and 95% quantiles. Fifty percent quantile results were later used to isolate a panel from the whole area and create a mosaic representation corresponding to the daily advance rate of the longwall face. This approach helped to estimate the daily emissions of this panel from the caved zone and from the fractured zone. Results showed that gas-in-place in the Pittsburgh coal seam, in the caved zone, and in the fractured zone showed spatial correlations that could be modeled and estimated using geostatistical methods. This study showed that gas-in- place volumes in the study area may be as high as 12.3 Bscf and as much as 3.5 MMscf per acre of mining.

Jan 1, 2012

By P. Massacci, F. La Marca, G. Bonifazi

Certain deposits of incoherent materials which are near the surface and exploitable by open-pit mining may be characterized in real time before they are mined through an analysis of ground-surface imagery. If the slice to be stripped is not overly thick, in fact, surface texture and color properties may be extrapolated to its entire thickness. Image analysis techniques to process ground surface images acquired in situ(or in the laboratory shortly after their acquisition) which yield pattern vectors representative of RGB color component distributions and HSB texture parameters have been developed. The techniques were applied to a mineral sandy ore deposit containing three different lithotypes. Geostatistical analyses showed that the data used to characterize the lithotypes were reliable. The correct recognition of the lithotypes was carried out using a multi-barycenter classification algorithm. Such in situ image-analysis procedures open the way to the proper selection of the ore to be mined, or the proper way for run of mine (r.o.m).processing, or the appropriate blend to be processed before or at the same time as the mining process itself is enacted.

Jan 1, 1999

By S. Mendenhall

The Golden Sunlight Mine (GSM) began operation in 1982 with a strong commitment to environmental stewardship and the local community. This commitment ensured the long-term physical, chemical and ecological stability of the mine site and maintained an active partnership with local stakeholders. Concerns for economic development intensified as mine closure loomed on the horizon and fostered the inception of the Community Transition Advisory Committee(CTAC).This coalition of interested area stakeholders has the primary focus to sustain current mining operations while concurrently seeking alternative post-mine economic development opportunities utilizing existing mine assets. Accomplishments include development of an Asset Re-utilization and Post-closure Plan, a community survey regarding the impending mine closure, recruiting an international wind energy company to develop a wind farm, and development of an industrial/business park. The synergy of this strong partnership is key to meeting sustainability goals and enhancing potential future mining operations. The cooperative effort of the GSM and the local stakeholders is a success story that could be a role model for other mining operations.

Jan 1, 2004

By Ian Martin

A precious metals refinery’s switch to personal computer-based, three-dimensional piping design saved many hours in the design of a South African precious metals refinery. Bateman Minerals and Industrial provided engineering, procurement and construction management services for Impala Platinum Limited-Refineries’ new $60 million refinery in Springs, South Africa. This project is one of the largest platinum refineries in the world. Bateman evaluated a new design method during this project that involved developing a three-dimensional model for the project. The new method saved time by reducing the man-hours required to generate complete project documentation, including plans, sections, isometrics and material takeoffs. The new method also saved design and construction time by allowing designers to detect clashes before construction began.

Jan 1, 2000

By Georgene Renner, William R. Yernberg, Steve Kral

ABB offers complete electrical revamps of mining shovels with ac or dc drives, drive control, frequency converters with insular gate bi-polar transistor technology, intelligent control packages and visualization. Many of the world’s shovel excavators and draglines (walking excavators) were built in the1980s. After 15 to 20 years of round-the clock operation in openpit mines, these machines start to feel their age. Electrical parts are particularly vulnerable. Their performance deteriorates and availability and productivity fall. Even with regular ser-vice and maintenance, a machine of this age will accumulate 400 hours of unscheduled downtime a year. The need for a replacement becomes pressing, but the expense is often prohibitive.

Jan 1, 2005

By Steve Kral

It seems that mining has been in the doldrums for awhile. Except for gold, metals prices remain depressed. And economic conditions in the United States and around the globe have put governments in a financial bind. This affects new building and infra-structure repairs, which, in turn, have a major impact the building materials industry. Add to that the severe environmental and regulatory restrictions placed on the mining industry in developing new mines and expanding existing ones. It’s enough to make a mining engineer/geologist/metallurgist go sell real estate. So why do those employed in the mining industry stay in the business and remain optimistic? Many of them will say that they have been through down cycles before and know that an upswing is in the offing. They also know that society will always need the commodities they produce. And they love the challenge. The challenge in mining’s case is producing commodities as cheaply as possible, in an environmentally sound manner and improving the quality of life in the communities where they work.

Jan 1, 2003