Search Documents

By C. Snyman, M. Le Roux, Q. P. Campbell, S. Engelbrecht

Due to the ultrafine particle size required for effective processing of chromite ores, dewatering of the concentrates presents a challenge. It is not uncommon for the ore to have elevated moisture contents even after dewatering, which must be reduced to required levels of between 8% and 10% by mass for further processing. Contact sorption drying has shown promise in test work on fine coal. This method was used to study the dewatering of chromite on a laboratory scale using 3 mm spherical activated alumina ceramic beads as a sorbent. Three different sorbent-to-chromite mass ratios, namely 0.5:1, 1:1, and 2:1, were tested with different process conditions, including dewatering in a stationary and a rotatingl bed. The experimental work showed that it was possible to achieve the target moistures in less than 10 minutes, irrespective of the sorbent-to-chromite ratio used. Ratios of 1:1 or higher, however, proved to be the best. The sorbent reusability at mass ratios of 1:1 and 2:1 were therefore tested. With a 1:1 mass ratio, the sorbents could be reused for three cycles, while with 2:1 ratio, the number of cycles increased to six. The sorbent-to-chromite mass ratio used had a significant influence on the required contact time and the reusability of the sorbents.

Oct 3, 2023

By A. M. Venter, C. W. Siyasiya, N. K. K. Arthur, M. G. Willemse, D. Marais

Although additive manufacturing is fast gaining traction in the industrial world as a reputable manufacturing technique to complement traditional mechanical machining, it still has problems such as porosity and residual stresses in components that give rise to cracking, distortion, and delamination, which are important issues to resolve in structural load-bearing applications. This research project focused on the characterization of the evolution of residual stresses in Ti-6Al-4V extra-low interstitial (ELI) additive-manufactured test samples. Four square thin-walled tubular samples were deposited on the same baseplate, using the direct energy deposition laser printing process, to different build heights. The residual stresses were analysed in the as-printed condition by the neutron diffraction technique and correlated to qualitative predictions obtained using the ANSYS software suite. Good qualitative agreement between the stress measurements and predictions were observed. Both approaches revealed the existence of large tensile stresses along the laser track direction at the sections that were built last, i.e., centre of the top layers of the samples. This in addition leads to large tensile stresses at the outer edges (corners) which would have the effect of separating the samples from the baseplate should the stresses exceed the yield strength of the material. Such extreme conditions did not occur in this study, but the stresses did lead to significant distortion of the baseplate. In general, the microstructures and spatial elemental mapping revealed a strong correlation between the macro-segregation of elemental V and the distribution of the β-phase in the printed parts.

Feb 6, 2023

By N. du Preez, J. Christie, F. Crundwell

Precipitation is a key process in the recovery of copper and cobalt. While there is a wealth of experience in operating precipitation steps, improving their performance remains challenging. Chemically, the reaction might be controlled by reaction kinetics, be limited by oxygen mass transfer, or be at equilibrium. In this paper, we examine these different operating regimes and demonstrate how they can be identified from plant operating data, process modelling, and pilot plant test work

Jan 1, 2023

By Nicolle Krusberski

Potential errors in XRF analysis are discussed and investigated with specific reference to the analysis of ilmenite samples. A selection of ilmenite samples was chosen and prepared using two XRF preparation techniques: pressed powder pellet and unroasted fusion bead. The merits of the two methods have been discussed in this paper for ilmenite analysis by XRF. Recommendations have been made regarding the use of pressed powder pellets especially with regard to the mineralogical effects that were evidenced during this investigation. The fusion bead technique was found to be far more accurate and able to meet short turnaround requirements provided the calibration methodology used is specific to the grade of samples analyzed.

Jan 1, 2014

By M. Asghari, R. Amiri, A. Haratian, M. Noue Parast, S. Haji

Today the roller screen has a wide range of applications in the steel-making industry. It is used for screening of green pellets before using the kiln. Since the appropriate size of a green pellet is -16+9 mm, there are different gaps between rollers that make green pellets classified in three categories: -9 mm (undersize), -16+9 mm (onsize) and +16mm (oversize). The efficiency of a roller screen is specified according to the weight percent of undersize in onsize as a fine material, and weight percent of onsize in oversize (loss). This efficiency is influenced by different operational parameters such as roller diameter, roller speed, and roller gap, material type of rollers and inclination of roller screen. This study investigates the effect of different material types of rollers in efficiency of Ardakan roller screens, located in the Yazd province of Iran. The rollers of the existing roller screens in this pelletising plant are made of polyurethane which according to this investigation, has a maximum lifetime of about six months. Operating the polyurethane rollers beyond its lifetime generates serious problems such as high wear of rollers, and consequently, material buildup on the roller surface which then significantly decreases the roller screen efficiency. So, after examining different roller materials, stainless steel 304 with higher surface roughness to help pellets move properly on the roller screen surface was selected as a solution to this problem. The new roller screen was constructed by Fakoor Meghnatis Spadana (FMS) and replaced the previous one. In this way, the maximum capacity of the roller screen was increased about 17% and the roller screen efficiency was increased about 15%. Keywords: Roller screen, green pellets, efficiency, onsize, operational parameters

Jan 1, 2020

By J. L. Havenga, L. J. van der Walt, J. T. Nel

"SynopsisThe development of plasma technology at Necsa started in the early 1980s, when the applicability of high-temperature plasmas in the nuclear fuel cycle was investigated. Since 1995, this plasma expertise has expanded to other industrial applications, for example mineral beneficiation, nanotechnology, fluorocarbon production and waste treatment, all of which are also of relevance to the nuclear industry.Necsa has demonstrated the manufacture of plasma-dissociated zircon, zirconium metal powder, carbon nanotubes, silicon carbide (SiC), zirconium carbide (ZrC) and boron carbide (B4C) at the laboratory and pilot plant scale. These materials are commonly used in the nuclear industry. Zirconium alloys are used as fuel cladding material for nuclear fuel assemblies.Necsa manufactured the monomer tetrafluoroethylene (TFE), using 150 and 450 kW DC plasma systems, from which the polymer polytetrafluoroethylene (PTFE) was synthesized for use in filters and as seals in nuclear plants. With the nuclear renaissance at hand, it was demonstrated that plasma technology can be used to produce hydrofluoric acid (HF), which is used in the manufacture of fluorine gas (F2) for the production of uranium hexafluoride (UF6) directly from the mineral calcium fluoride (CaF2) without the use of sulphuric acid as in the conventional process. The recovery of valuable uranium from nuclear waste such as filters, oils, and solids with plasma processes will also be discussed. The destruction of low-level nuclear waste by a plasma gasification system can reduce the volume of this waste by several orders in magnitude, resulting in huge savings in the storage costs. Another product of plasma technology is the encapsulation process for nuclear waste and the production of vitrified product, which could be used as filler material for medium-level nuclear waste.IntroductionDuring the 1980s, a plasma research and development programme was launched at the erstwhile Uranium Enrichment Corporation of South Africa (UCOR) at Valindaba outside Pretoria. The main purpose of this programme was to develop alternative and more economical processes for the processing and manufacturing of uranium compounds used in the nuclear fuel cycle. The conversion of UO2 (as received from uranium mines) to UF6, which is needed for enrichment, conventionally involves several laborious, expensive, chemical processing steps. Plasma processes can eliminate several of the intermediate steps. Enriched UF6 is converted to UO2, which is pressed into pellets that are used in nuclear power plants. Plasma technology could also be used in a modified and optimized conversion process."

Jan 1, 2015

By B. S. Agbenuvor, R. Morrison, V. Jokovic, C. Antonio

Body breakage usually involves breakage of particles by compression between two surfaces or impacted against a rigid surface, with the latter of interest in this current study. This mode of breakage has been identified to be the most elementary size reduction process and the most effective breakage process in comminution devices. It has been found in the literature that the progenies produced from this form of breakage possess a residual velocity at which they move, after the breakage event. In the pursuit of efficiently utilising applied comminution energy, a laboratory-scale breakage device has been developed to deliver precise specific impact breakage using the concept of a fast-moving hammer and a slow-moving particle to effect breakage. The residual velocities of the progenies from the breakage event may be used to generate secondary breakage without further addition of energy if the particle encounters a stiff obstacle such as a steel plate at right angles to its path. To measure the extent of secondary breakage, the steel wall of the device was lined with a rubber material to suppress the second set of breakage events. The performance of the new device is analysed, based on calculated t10 values and measured residual velocities of the moving daughter particles. Testing involving anvils showed a much finer PSD and higher t10 compared to the test involving rubber lining. This finding is corroborated by the measured residual velocities of the progenies. The resulting energies calculated from the measured residual velocities of the progeny were found to be approximately 42-88% of the primary specific impact energy. This retained energy was found to be sufficient for secondary breakage. Keywords: Impact breakage, residual velocity, secondary breakage, energy utilisation

Jan 1, 2020

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

By M. Splaine, W. Davison, D. C. Atkinson

"Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year L.P. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efffciency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations.Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system."

Jan 1, 2014

By D. Odendaal, S. Bharat, R. D. Cromarty

The aim of this investigation was to determine the effect of high-temperature heat treatment on the electrical resistivity of charcoal. Samples of two different wood types (eucalyptus and black wattle) were pyrolised in a retort at a temperature of 700°C and the resulting charcoals heat-treated in an induction furnace at temperatures from 800°C to 1800°C and residence times from 60 to 120 minutes. After cooling, the resistivities of the samples were measured at room temperature using the four-point probe technique. It was found that as the heat treatment temperature increased the electrical resistivity of the charcoal decreased, approaching an asymptotic value at higher temperatures. Longer residence times decreased the resistivity, but this effect was not pronounced.

Oct 3, 2023

By E. Arghavani, S. H. Amiri, S. Zare, F. Sepehri, M. Ramezanizadeh

Mineral processing plants include different stages like crushing, grinding, classification and concentration, all of which have partially affect the final product. To identify and solve the related problems of each stage, process audition should be carried out continuously to find the major solutions of improving product and decreasing the maintenance and operating costs. The Iranian Gohar-Zamin iron ore beneficiation plant consists of equipment such as gyratory and cone crushers, high pressure grinding rolls (HPGR), ball mill, dry and wet double-deck vibrating screens, hydrocyclones cluster, magnetic drum separators, thickener and horizontal vacuum belt filters. The defects of initial design as well as current non-standard operating conditions of equipment were monitored and detected and the opportunities for process optimisation were presented as follows: establishing the control loop of power draw for cone crushers, the modification of feeding chute in cone crushers to minimise the non-uniform wear of parts, removing segregation in the fresh feed bin and screen’s circulating load chute in order to provide the proper feed to HPGR, reducing wear rate on HPGR rolls surfaces, decreasing the amount of rejected materials in screen, equalising the solid content and particle size distribution (PSD) of feed in all magnetic drum separators and equalising the PSD of hydrocyclones overflow. This paper provides a guideline for the mineral processing industry to focus its efforts on process design to deliver the efficiency with minimum capital costs. Keywords: Process audition, gyratory crusher, cone crusher, HPGR, screening, hydrocyclones, magnetic drum separators

Jan 1, 2020

By B. Mbuya, A. F. Mulaba-Bafubianda, J. M. Mvita

The paper explains the main effects of input leaching parameters, such as addition of a reducing agent, acidity, agitation, temperature, and leaching system potential, in relation to observed and predicted yields of sought-after cobalt. An artificial neural network coupled with graphical probability networks was developed wherein the abovementioned input parameters were used to predict the percentage of dissolved cobalt. Furthermore, similarities and differences between the Bayesian and neural network approaches in terms of their key outcomes are compared with respect to study of the dissolution of cobalt in sulfuric acid. Key results indicate that there is a need to use neural network results to predict conditions for dissolution of cobalt, while using Bayesian network to explain inferences about conditions of the input parameters, thereby achieving realistic predictions.

Jan 1, 2023

By I. B. Fernandes, M. A. Reuter, A. Abadias Llamas

Metallurgical simulation and evaluation of the resource efficiency of whole production processes are of key importance for impact assessment, in terms of environment and resources. Exergy is a measure of resource consumption, taking into account energy, raw materials, water, and chemicals; which allows for the evaluation of different technologies to find the most resource efficient and environmentally friendly process. This paper compares the sustainability for production of rare earth magnets from primary and secondary resources through an exergetic evaluation of the production process, in addition to traditional life cycle assessment (LCA). The methodology makes use of simulation tools for tracking material flow and resources used, based on thermodynamic laws, from ore exploitation to magnet production and recycling. It highlights areas with the greatest potential for improvements in terms of resource consumption and environmental impact generation, having a thermodynamic-validated flowsheet for primary and secondary production of NdFeB magnets, present in several low-carbon technologies, such as wind turbines, electric vehicles, and cooling systems. It demonstrates the minimum exergy destruction for magnet production, through an irreversibility breakdown chart, showing where irreversible material and energy losses occur. Results show that CO2-equivalent emissions for producing NdFeB permanent magnets from primary resources could be twice as high when compared to magnets produced from recycling technologies. The theoretical maximum exergetic efficiency for primary production is 57.61%, whereas for permanent magnets produced from secondary resources, the exergetic efficiency reaches up to 82.89%. Two magnet recycling technologies were evaluated, i.e. in acidic medium and via hydrogen decrepitation, and it was observed that their exergetic efficiency and environmental impact performed better than production from primary resources. Keywords: Resource efficiency, exergy analysis, permanent magnet recycling, process simulation, system design

Jan 1, 2020

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By C. Banff, E. C. F. Hamman, J. Venter

Open pit slope stability analyses for large scale instabilities are often carried out using limit equilibrium, finite element or finite difference computer programs. All of these require empirical estimates of rock mass shear strength when calibrated values are not available, which is a common occurrence. A common method of estimating rock mass shear strength is the Hoek-Brown failure criterion, which often over- or underestimates rock mass shear strength when used in limit equilibrium or elastic linearly plastic slope stability analyses, resulting in published alternative estimates for the coefficients of the Hoek-Brown failure criterion. This paper investigates the differences between limit equilibrium and elastic linearly plastic slope stability analysis based on the Hoek-Brown failure criterion. The investigation consisted of a comparison of 3840 RS2 finite element analysis models completed with strain softening, and 216 Slide2 limit equilibrium models. The models were used to evaluate a methodology to determine equivalent limit equilibrium and elastic linearly plastic shear strength parameters that provide the same stable slope angles and instability back break distances as the more representative strain softening stress analysis methods. This paper presents the methodology and compiles the results into design charts and equations for equivalent limit equilibrium Mohr-Coulomb shear strength parameters, that simplify calibration against actual case studies. The results compare well with older empirical shear strength estimates, however, a detailed calibration of the results against case studies will need to be carried out. The analysis also did not consider pore pressure effects; this is left for future publication.

Sep 1, 2025

By C. Liu, F. Ye

"To extend the variety of lump ores that are used in the COREX shaft furnace and to optimize iron ore blending, the original evaluation method for iron ores that was proposed by Voestalpine AG has been improved. Physicochemical and metallurgical properties of iron ores, including Sishen lump ore and CVRD pellets, which are currently used in the COREX process, and three other lump ores, were assessed and compared. Ore matching principles were proposed and five optimized iron ore blending schemes designed and verified by laboratory experiments to prove the effectiveness of the improved evaluation method. The replacement of Sishen lump ore by the alternative L2 and L3 lump ores without varying the proportion of CVRD pellets could improve the degree of reduction and rate of metallization, and decrease the bonding index. Based on the results of laboratory test work and industrial- trials, an ore blending scheme of 60% CVRD, 20% L2, and 20% L3 is recommended for use in the COREX process. IntroductionIn recent years, problems such as environmental pollution and a shortage of coke and coal resources for blast-furnace ironmaking have become increasingly apparent. Based on sustainable developments in the iron- and steelmaking industries, the environmentally friendly COREX smelting-reduction process with low energy consumption was developed and introduced (Zhou and Du, 2013; Song, Lv, and Yin, 2015; Xu et al., 2016; Kurunov, 2010). The evaluation system for lump ore that was proposed by Voestalpine AG recommends that only Sishen lump ore from South Africa be used in the COREX process, because of the stringent physicochemical and metallurgical property requirements. This situation significantly hampers improvements to the technical and economic aspects of the COREX ironmaking process, especially in China (Eberle, Siuka, and Bohm, 2006). No theoretical or technical basis has been provided for the evaluation system, and the assessment approach for iron ores also presents problems that need to be discussed and resolved.The COREX process consists of two reactors: the prereduction shaft furnace and the melting gasifier as shown in Figure 1 (Wu et al., 2017). Pellets and lump ores which are charged to the prereduction shaft should have a good reducibility and metallization with a low degradation index (Li et al., 2016; Wu et al., 2011; Kumar et al., 2009; Kang, Gupta, and Sahajwalla, 2007). The properties and microstructure of the iron ore pellets which are required to achieve a high productivity and a lower fuel rate in the COREX process have been investigated (Umadevi et al., 2011). Some efforts have also been made to investigate the behaviour of lump ores in the COREX shaft furnace, including the disintegration characteristics and the reduction degradation (Umadevi et al., 2011; Zhou et al., 2015; Xu et al., 2013; Li, Feng, and Zou, 2013; Hou et al., 2014). However, few studies have focused on the optimization of ore blending for partial or total substitution of the expensive Sishen lump ore by other, cheaper lump ores to reduce the production cost. The technology for the utilization of blended lump ores in the COREX process is still in its early development stages (Zhou et al., 2017; You et al., 2017)."

May 1, 2019

By N. V. Moraka

Mining companies are required by law to improve representation of women on their boards. However, progress in this regard has been slow. Boards of directors play an important role in formulating corporate strategy, risk assessment, and effective governance for sustained financial performance. Although some women have successfully maintained board seats, others have been unable to do so. It is difficult to ascertain whether women are being appointed as tokens to satisfy social pressures, as little is known about the experiences of women board members in mining, which may inform or refute tokenism. In-depth interviews were conducted with 20 women and 16 men across six listed mining companies. Thematic data analysis revealed evidence of tokenism where recruitment to mining boards is compliance-based and is informally driven by influential directors. Adverse boardroom experiences that further confirmed tokenism were reported by women, such as disregarding their contributions, condescending behaviour, and limited influence in decision-making, while other women sought to validate their competence and oppose social exclusion. This study recommends that a strong Board Chair and nominations committee is critical to ensure sustainable recruitment of competent and suitably qualified women; and further foster a culture of inclusivity and valuing gender-diverse boards.

Dec 13, 2023

By Z. Botha

Sheryl Sandberg, the COO of Facebook, published a book titled 'Lean In', where she invites women to sit at the table. In summary, to 'sit at the table' entails not only embracing opportunity, but to actively seek out opportunities in leadership positions. Sandberg points out that, unfortunately, apart from institutional obstacles, a woman's own perceived limitations have a negative impact on her leadership ambitions. To create an environment where diversity will flourish, where everyone has a seat at the table and everyone has a voice, safety must be established first. To establish safety within a diverse team, there is power in relationships and connections. This study will first and foremost review theories in literature as to why diversity and inclusion are so important and the value that diversity brings to our industry. The study also recommends a few focus areas for improving diversity and inclusion in the industry.

Sep 1, 2022

By C. J. Lenz

The results of prospecting operations involving geological data and a large number of geochemical determinations of the metal content of soil samples are plotted and evaluated by computer. Anomalous areas are identified in each type of environment by selecting probability or population boundary values from frequency distributions. The anomalies are plotted to permit correlation with geographical or geological features. Ranking of prospecting targets is made using geographic pattern, geology, absolute value and metal ratios. Three short case histories are presented.

Jan 1, 2014

By O. K. H. Sheff

An editorial in the April 1990 edition of Mining Magazine is worth a wider audience in South Africa, particularly as the SAIMM enters its own centenary decade and the process of change in the minerals industry world-wide makes increasing demands on the professionalism of its leaders. The editorial considers the changing status of engineers, who up to the 1880s had been held in high regard by society. Alumina and bauxite Economists forecast a slower economic growth rate in 1990, but expect continued increase in demand for aluminum at a 3 per cent annual rate during the decade. Structural and numerical analysis Struceng & Femcad (structural analysis and finiteelement method) is a conference and exhibition that is to be held in Grenoble (France) on 17th and 18th October, 1990. It is sponsored by the Institute for Industrial Technology Transfer (ITT-International).

Jan 1, 1990