Search Documents

By G. M. Evans, S. Mitra, G. J. Jameson, M. M. Hoque, E. Doroodchi, R. Moreno-Atanasio

In this study, the detachment behaviour of 314 μm diameter silica particles from a single 3 mm diameter bubble rotating in a confined cavity connected to a cross-flowing water channel was investigated. The liquid cross-flow generated a rotating flow inside the confined cavity, which was quantified using 2D particle image velocimetry (PIV) measurements. The fluctuating (x-y) velocity components inside the cavity for each cross-flow velocity, U, were then used to estimate the corresponding time/volume average turbulence intensity values, Ti. Turbulence intensity ranged from 9.3-16.2%. In the absence of a bubble, the rotating vortex within the cavity created a pressure field which decreased towards the centre of the vortex; wherein the lowest pressure zone was located at the centre of the cavity. The vorticity into the cavity was found to increase with increasing the turbulence intensity. A bubble, both without and with particles attached, was introduced into the cavity under different flow conditions and its motion was tracked using the shadowgraphy technique. Experimentally, it was found that the bubble-particle aggregate was trapped at the centre of the cavity (low-pressure region) following a spiral trajectory. An interface resolved 3D computational fluid dynamics (CFD) model was developed to predict the particle detachment conditions within the confined cavity. CFDpredicted vorticity in the absence of a bubble agreed well with experimental observation. The CFD analysis indicated that the vorticity inside the cavity was not significantly changed when a single bubble was introduced. On this basis, the computed vorticity was utilised in describing the force balance applied to the attached particle. Computationally, it was found that the critical turbulence intensity, beyond which the particle was detached from the bubble, was 14%. This value was consistent with the experimental observation of detachment at Ti at 15.7%, and above, but not at lower values. Keywords: Bubble, particle, turbulence intensity, vorticity, particle detachment, CFD, PIV

Jan 1, 2020

By O. Barron, C. Felix

In 2023, polymer electrolyte membrane fuel cell membrane electrode assemblies accounted for about 62% of the global fuel cell market share and this demand is expected to grow. Commercialisation requires technologies capable of cost-effective, high-volume manufacturing. The membrane electrode assembly is crucial and represents a significant cost to polymer electrolyte membrane fuel cell manufacturing. Manufacturing the electrode components for membrane electrode assemblies at high volumes can reduce production costs while delivering on the forecasted industry demands. Roll-to-roll is a mature coating technology applied in various manufacturing industries such as batteries, printed electronics, microelectronics, photovoltaics, printing, paper consumables, etc., with significant potential for polymer electrolyte membrane fuel cell manufacturing. While the high-volume production process for membrane electrode assembly manufacturing differs from laboratory-scale, the membrane electrode assembly structure remains unchanged. Roll-to-roll is a continuous coating process with speeds of 10 m/min being achieved. In this work, MicrogravureTM and slot-die coating methods have been adopted and have shown promising outcomes for producing gas diffusion electrodes for membrane electrode assemblies. An overview of the MicrogravureTM and slotdie coating methodologies is provided, and a discussion on preliminary results and challenges are presented. Work on MicrogravureTM gas diffusion electrode manufacturing has already achieved comparable performance with spray-coated gas diffusion electrodes. The influence of coating parameters and drying on the coated catalyst layer quality is discussed.

May 27, 2025

Excessive dust generation from unpaved mine haul roads is a problem common to most surface mining operations. While optimal road wearing course material selection parameters reduce the inherent dust generation potential, they do not totally eliminate fugitive dust. Many different classes of suppression or palliative treatments are available for mine haul roads and this paper initially ascertains basic selection guidelines, using a set of ideal dust palliative product, application and performance parameters based on mine road-user requirements. An evaluation and modelling methodology for truck generated fugitive dust emissions is developed as a basis for the comparative assessment of dust control strategies. For water-based spraying, a watering model was developed to estimate individual mine road watering frequencies for characteristic site parameter combinations during summer and winter operating conditions, for a required level of control or maximum dust defect. This forms the base-case scenario with which to compare the performance of other types of dust palliatives under the same conditions. Finally, a basic palliative economic evaluation model is introduced with the aim of identifying and costing the establishment, application and maintenance rejuvenation activities associated with the use of chemical palliatives. While palliative cost and performance is generally site specific, it is shown that under certain combinations of conditions, the use of dust palliatives has the potential to deliver cost savings when compared to water-based spraying.

Jan 1, 2007

By D. Moses, J. A. Onyango

Carbonatites are generally competent rock masses with rock mass rating class II rating 60–74. In spite of their competency, they tend to be affected by weak features like manganese-iron veins and/or in situ rock damage due to brecciation associated with carbonatite complexes. Rock slope failure in such hard rocks is complex since such structures within the rock mass form weak links that could potentially control slope instability. In this contribution, a numerical simulation using phase2 v 7.0 was carried out to investigate the influence of in situ rock damage on the stability of mine pit walls. The outcome reveals that, the existence of breccia in the competent rock mass has the capability to reduce the slope stability performance particularly at gentle dipping angles of emplacement in close range to the slope toe. However, as the emplacement position of breccia moves away from the pit wall, the stability performance increases at gentle dipping angle <50º. On the contrary, at the dipping angle of 50° the performance of slope reduced, and at steeper angles >50° the impact becomes negligible. Thus, from a series of analyses, mine design in brecciated rock masses, the ratio of 1:5 between the breccia distance from slope toe and pit depth should be implemented to counter its impact, and if the breccia is within or close to the pit limit, a deliberate effort must be made to mine it out.

Sep 1, 2025

By K. Isaac, S. O. Bada

This research focuses on the co-firing of discard coal with refuse-derived fuel (RDF) to utilize this abundant resource in South Africa for energy generation and reduce the volume of waste disposed of at landfills. The potential of a coal with a high ash content (> 40%), which is a grade used in some power stations in South Africa, and its combustion compatibility with two different RDFs in terms of emission reductions has been established. Gaseous emissions and ash residues from the combustion and cocombustion of the coal, two different RDFs and coal/RDF blends of different proportion were analysed. One of the RDF samples contained mostly paper (PB) and the other mostly plastic (PL). Co-combustion ash from the discard coal and RDFs showed a decrease in chloride and alkali metal contents as the coal ratio in the blend increased. The slagging propensity of the co-fired blends was found to be very low, while the propensity for fouling decreased from high to medium for all the blends with < 75% RDF. Cocombustion of RDF with coal showed a decrease in SO2 emissions from 387 ppm (discard coal) to 50 ppm for the sample containing 25% coal discard plus 75% PL. A 15% PL to 85% coal blend also reduced NOx emissions from 145 ppm (100% PL) to 88 ppm. The lowest CO2 emission observed was 6000 ppm for the blend of 85% discard coal plus 15% PB. It was established that the most favourable fuel blend that can produce the lowest sulphur emissions if used for power generation is the 25% coal discard plus 75% PL sample.

Aug 2, 2022

By P. P. Kim, M. Tangstad, T. A. Larssen

"The kinetics of MnO and SiO2 reduction in SiMn slags based on Assmang/Comilog ore and HCFeMn (highcarbon ferromanganese) slag were investigated between 1500 and 1650°C under a CO atmosphere. The results showed that charges containing HCFeMn slag had relatively faster reduction rates than those without. The difference in the driving force for MnO reduction was insignificant among the SiMn slags at 1500°C, which implies a low contribution of the driving force for reduction rate. The slag viscosities were also rather similar, around 1 poise at 1500°C, which could not explain the different reduction rates. Instead, the different charges containing various sulphur contents are believed to give rise to the varying reduction rates. The estimated activation energies for MnO reduction were around 500–920 kJ/mol for charges containing HCFeMn slag, and between 250–300 kJ/mol for those without. Based on the estimated kinetic parameters, the considered rate models were able to describe the reduction of MnO and SiO2 in SiMn slags between 1500 and 1650°C. IntroductionManganese ferroalloys such as ferromanganese (FeMn) and silicomanganese (SiMn) are important ingredients in steel production due to the beneficial effects of manganese on the physical properties of steel. Mn enhances the strength, toughness, and hardness of steel products, and both Mn and Si are used as deoxidizers to prevent the development of porous structures (International Manganese Institute, 2014; Olsen, Tangstad, and Lindstad, 2007; Subramanyam, Swansiger, and Avery, 1990; Tomota et al., 1987).The thermodynamic background of manganese ferroalloys is well established (Olsen, Tangstad and Lindstad, 2007), but kinetic information is rather scarce, especially for the SiMn process (Tranell et al., 2007; Tore-Andre Skjervheim, 1994). The absence of kinetic information makes it more difficult to understand the reduction mechanisms of MnO and SiO2. It is not clear how different raw materials affect the SiMn process. The main metal-producing reactions in the SiMn process are described by Equations [1] and [2]:"

May 1, 2019

By and M. V Roper, H. N. Engelbrecht

Quality control interventions emanate from process upsets and trends that move product quality beyond the natural variation expected in a stable process. The ability to detect upset conditions and react in an effective manner protects both resource utilisation and compliance to specifications. Product quality control on coal processing plants traditionally relies on the reference (combined sampler and laboratory) system to measure product qualities. The introduction of online analyser (OA) technology, applied in different configurations, creates a second source of measurement information for control decision making. The case study was done on the primary sample stream of the final product stream at Exxaro’s GG7 and 8 plants, part of the Grootegeluk complex. It explores the OLA system’s ability to meet the OEM performance guarantee, perform equally to the reference system without analytical delay time, and assesses the effort to achieve this performance in a by-line analyser (BLA) configuration. In the paper, a conceptual comparison of the two measurement systems is done and the theoretical and practical comparison of measurement performance is discussed. Results demonstrate that the OA outperformed the OEM’s performance guarantee and achieved similar levels of performance to the reference system without the response delay. Keywords: Online analyser (OLA), by-line analyser (BLA), coal quality measurement, measurement performance

Jan 1, 2020

By D. Visser

This paper is based on the Townlands Ore Replacement Project whereby the concept of conventional sinking of one large diameter shaft was declined and replaced with three smaller raise bored shafts. A wire line geophysical survey was done and the results indicated that a single shaft larger then 4 m diameter unsupported would not be suitable. The shafts were placed 28 meters apart measured from centre to centre. To ensure that the skin to skin pillars between the shafts remained regular and to minimise any deflection, the pilot holes were drilled with the Rotary Vertical Drilling System. The different shaft sinking methodologies are discussed explaining the risk associated with each method.

Jan 1, 2009

By D. Visser

This paper is based on the Townlands Ore Replacement Project whereby the concept of conventional sinking of one large diameter shaft was declined and replaced with three smaller raise bored shafts. A wire line geophysical survey was done and the results indicated that a single shaft larger then 4 m diameter unsupported would not be suitable. The shafts were placed 28 meters apart measured from centre to centre. To ensure that the skin to skin pillars between the shafts remained regular and to minimise any deflection, the pilot holes were drilled with the Rotary Vertical Drilling System. The different shaft sinking methodologies are discussed explaining the risk associated with each method.

Jan 1, 2009

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached to remove base metals from a concentrate containing platinum group metals (PGMs). We investigated the atmospheric leaching process to develop a better understanding of the leaching behaviour of the base metals (Cu, Fe, and Ni) and the PGMs, in particular Ru, Ir, and Rh with respect to key process variables, acid concentration, and Cu concentration under oxidative and non-oxidative conditions. With oxidative leaching, a higher initial acid concentration resulted in higher Cu, Ni, and Fe extractions, as well as faster leaching reaction rates. A higher initial acid concentration also resulted in faster precipitation of Cu, Ru, and Ir under oxidizing conditions. Under non-oxidative conditions, Ni and Fe extraction was much slower, and the effect of initial acid concentration on Cu precipitation was less pronounced. The initial Cu concentration had a slightly smaller effect on the leaching behaviour of Fe and Ni, as well as precipitation of Ru, Ir and Rh. Moreover, a higher initial Cu concentration suppressed both Ni and Fe leaching and had a slight inhibiting effect on the precipitation behaviour of Cu, Ru, and Ir.

Nov 1, 2021

The Annual General Meeting of the Branch was held in the Witbank Golf Club on Thursday, 28th August, 1969 at 5.00 p.m. Mr C. G. Sowry (Chairman) was in the Chair. There were also present: Ten Members: Messrs J. Meintjes (Vice-Chairman), J. E. van Aswegen, A. C. Hofmeyr, I. Botha, B. F. v. d. Merwe, C. H. Coxon, R. Canny, R. C. J. Goode, A. Bain, G. E. Carlyon. Six Associate Members: Messrs B. T. Hosking, R. E. Powell, W. Weber, T. Bulloch, E. J. Jackson, P. J. Muller. Fourteen Visitors. Total Present: 31. The Chairman declared the meeting open and extended a welcome to all visitors including Mr R. C. J. Goode, President of the Institute. MINUTES OF PREVIOUS GENERAL MEETING The Minutes of the General Meeting held on the 26th June, 1969, were read and adopted. CHAIRMAN&apos;S REPORT The Chairman presented a report outlining the activities of the Branch during the past year. Membership of the local Branch had increased from 80 to 99 during the year. DECLARATIONOF OFFICEBEARERS The Chairman announced that owing to his transfer out of the Witbank area, he was unable to accept the nomination as Chairman for a further year of office. The outgoing committee had elected Mr J. Meintjes Chairman and Mr A. Bain Vice-Chairman for the ensuing year. Mr J. Meintjes then took the chair. Mr J. Meintjes thanked Mr C. G. Sowry for his successful steering of the Branch during its period of inauguration. ELECTION OF COMMITTEE MEMBERS The Chairman then read the Scrutineers&apos; Report and declared the following eight members elected as Committee Members for the 1969-1970 year: Messrs I. Botha, A. W. Brereton, G. E. Carlyon, B. T. Hosking, E. J. Jackson, B. D. McNeice, P. J. Muller, B. F. van der Merwe. TALK The Chairman then called upon Mr A. Bain to present his talk and film show on &apos;Impressions of the mining and metallurgy congress tour to Australasia&apos;. CLOSURE After thanking the speaker for an interesting talk, the Chairman declared the Meeting closed at 8.40 p.m.

By L. A. Jordan, D. van Vuuren

A two-dimensional finite difference model has been developed to describe the reduction of kilogram quantities of dehydrated phosphogypsum. The model’s scope has been limited to focus on the heat transfer and reactions that occur within a mass of material contained in a vessel inside a furnace rather than also including the effects of heat transfer to the vessel. Changes in the heat transfer properties (k, ρ, and Cp) are incorporated as the composition of the mass changes as the chemical reactions progress. The model is validated against experimental data, with samples heated to 1000°C at 3°C min−1 while purging with nitrogen gas. A sensitivity analysis of model predictions to the pre-exponential factor of the reaction rate constant of the main chemical reaction and the thermal conductivity of the powder bed indicated that, at the envisaged process conditions, the behaviour of the system depends much more on the rate of heat transfer than on the rate of the chemical reaction. The model demonstrated a significant increase in accuracy when the thermal conductivity was modelled to increase linearly with temperature compared to assuming a constant value.

Oct 1, 2022

By M. H. Dehghanpoor, M. Zivdar, M. Torabi

"A hydrometallurgical route was developed to extract metals such as gold, silver, copper, and selenium from anode slime from Sarcheshmeh Copper Complex in Iran. For the extraction of copper by leaching, the anode slime was heated and stirred with 4 M sulphuric acid in the presence of oxygen. Optimal conditions for recovery of copper were temperature 80°C, mixing time 5 hours, and oxygen flow rate 2 L/min, resulting in a copper recovery of 94.47%. Silver and selenium were dissolved by leaching anode slime from which the copper had been removed with nitric acid. For gold extraction, anode slime was heated with aqua regia at 90°, and the gold then extracted with 2-ethyl-hexanol at a concentration of 0.5 M and phase ratio of 4. The extract was then stripped with soda solution at pH=10.5 and a phase ratio of 5. Finally, gold was recovered by precipitation with oxalic acid at a ratio of mass to volume 10 g/L. Total gold recovery was 80%. IntroductionDuring the electrorefining of copper, some metals are accumulated in the byproduct anode slime, which is an important source for recycling and recovery of these metals (Petkova, 1994). In this paper, a hydrometallurgical route is described for the recovery of precious metals from copper anode slime of Sarcheshmeh Copper Complex, which is located in southeastern Iran .Copper anode slime is black or gray powder with a particle size less than 200 mesh. Approximately 2 to 20 kg of anode slime is produced per ton of copper cathode. The slime is characterized by higher amount of Ag, Se, Pb, and Cu compared to other metals and a very low Au content (Khaleghi and Ghader, 2013).The copper anode slimes are composed of 11.69% selenium, 3.93% copper, 5.26% silver, 0.13% gold, and 45% barite, plus lead, tellurium, antimony, sulphur, and silica with small amounts of nickel, iron, zinc, and bismuth. Gold is one of the most important noble metals due to its wide applications in industry and economic importance, so recovery of gold from slime is more appealing than that of other metals. According to the World Gold Council (2013), the demand for gold has increased during the last decade. This increase is due not only to the increasing demands of the jewellery market, but also to the increasing demand for gold in industrial as well as medical applications (Ranjbar et al., 2014)."

Jan 1, 2016

By E. Govender-Opitz, L. Lelia

The South African mining industry plays a significant role in the economy of the country. Nonetheless, the negative impacts on the environment continue to prevail. In regions where mining exists in proximity to communities, mining activities have led to the disruption of modality. Rural communities are mostly affected as they depend on land use for agriculture to sustain their livelihoods. The conversion of land for mining activities often leaves the communities vulnerable when mines close because of the limited life span of mines. An ongoing discourse focuses on how the mining industry can contribute to sustainable development of the communities in which they operate. Post-mining transformation offers an approach for the mining companies to contribute to sustainable livelihoods post-mine closure by strengthening rural-urban linkages, which ensures inclusive development of both rural and urban areas. The paper employs a case study approach to Richards Bay Minerals and the adjacent rural communities of Sokhulu and Mbonambi. It sets out to understand the post-mining transformation employed by RBM and explore the rural-urban linkages that manifest as a result. Findings show that sand dune rehabilitation employed by RBM is successful in restoring soil fertility and establishing the natural ecosystem. The casuarina planted to rehabilitate the dunes is used to spur an alternative charcoal industry post-closure. The main rural-urban linkages that manifest are flows of people due to job opportunities and flows of goods from the sale of charcoal produced. However, there is a lack of communication and lack of authority to ensure responsible management of the casuarina plantation and equitable sharing of benefits. The paper recommends that other post-mining transformation strategies such as eco-tourism should be explored and that the government, at both national and local level, the community and the mine should be involved to ensure overall success and sustainability of the strategy. Keywords Post-mining transformation, rural-urban linkages, alternative land use

Jan 1, 2020

By Tian Yingzhong, Guo XIN, Wei Peihe

The intention is to solve a series of problems in the flotation and desiliconisation of complex bauxite; aiming to achieve monomer dissociation of target minerals based on process mineralogy. According to the mineral surface, there are differences in physical and chemical properties and the molecular design theory of flotation agents. Designing the polar and non-polar groups of the bauxite flotation collector to make the reagent group easily combine with the mineral to form a cyclic chelate, will enhance the collection performance, and strengthen the drug selection performance. Developing a new type of positive flotation collector for bauxite with small dosage, strong selectivity and low foam volume. Keywords: Process mineralogy, monomer dissociation, molecular design, new positive flotation collector

Jan 1, 2020

By G. J. McTeer, D. J. Rioux

Teck Metals Ltd operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Since 1997, KIVCETTM flash smelting technology has been utilized for the treatment of zinc plant residues and lead concentrates. Trail Operations’ furnace uses four water-cooled jackets for bullion tapping. This paper provides an overview of KIVCET bullion tapping for the past 16 years, and discusses successes and challenges encountered with respect to operations, training, and monitoring.

Jan 1, 2014

By E. M. Sacris

The semi-autogenous grinding mill is the bottleneck whenever treating hard and finely fragmented ore at Benguet Corporation&apos;s Kaline Concentrator. Low milling rates result from very high and fluctuating mill power draw. Attempts to use a mill horsepower control loop to regulate feed rate were unsuccessful because of operational upsets caused by fluctuations in feed rate on downstream operations. The objective of the computer control was to maximize tonnage throughput by stabilizing the power draw at a high but safe level without upsetting subsequent operations. The semi-autogenous mill is operated in closed circuit with a stationary screen. Instrumentation consists of a feed weightometer, a power transmitter to measure mill load, a headwater flowmeter and an ultrasonic level sensor to measure the mill discharge sump level. A 64 k-byte FOX-3 Foxboro computer processes field data from various sensors and manipulates the input control variables. These variables are the fresh feed rate and the headwater flowrate. Feed rate is controlled through a supervisor-type computer program aimed at maximizing and stabilizing power draw. The control scheme was according to how the operators responded during an operator-directed automatic control mode. Mill dilution is similarly controlled. Results achieved reflect a 3% increase in tonnage milled because of the reduction in control variability that ensued.

Jan 1, 1987

By T. Szendrei and S. Tose

Historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques, are inherently incapable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study.

Dec 13, 2022

By M. Karsten

Platinum mines in the Bushveld Complex are located in areas with a high geothermal gradient. This means that, compared to, for example, gold mines of the Witwatersrand region, high rock temperatures are encountered at relatively shallower depths. Thus air cooling and refrigeration need to be considered at early stages in mine development. Another factor that influences air cooling and ventilation requirements is the use of trackless diesel equipment for loading and hauling broken rock. At shallower depths it will be more cost-effective to locate the cooling and ventilation equipment on surface, whereas for deeper mines the more cost-effective option is to locate cooling equipment underground. For intermediate depths, trade-off studies need to be undertaken to determine the optimum mix between more cooling and less air or more air and less cooling, as well as the optimum location for this cooling equipment. Factors that are taken into account include power requirements, positional efficiency, and additional infrastructure requirements. Traditionally the approach has been to ventilate ?all of the mine all of the time?. However, with increasing power costs and growing pressure to ensure sustainability, this strategy must be modified to apply ventilation and cooling on demand. In other words, both cooling and ventilation equipment should be operated only when needed and should be adjusted to the demand at the time. Obviously there will be areas that will need to be ventilated (and cooled) continuously (for example, for dilution of flammable gases), but this can be built in to the overall strategy. In addition, in devising ventilation on demand (VoD) strategies, occupational criteria relating to exposure to gases, noise, and heat need to be taken into account. This paper discusses options available for implementing energy-efficient ventilation and cooling systems and suggests ways of changing traditional thinking in the overall ventilation and cooling of mines. Efficient ventilation and cooling designs can play a major role in improving sustainability and reducing energy costs and carbon footprint.

Jan 1, 2012

By A. Chuma, K. J. Nyembwe, H. Simonsen, J. H. Potgieter

Different concentration techniques were evaluated for preconcentration of a mineral ore at a coarser size to avoid energy and resource wastage. Specifically, the aim was to reduce milling costs and energy required in the beneficiation of tin. In this study, cassiterite (0.17% Sn) was the mineral of interest in a pegmatite ore body associated with quartz (SiO₂ > 60%) and alumina (Al₂O3 > 20%). Three concentration techniques, namely dense media, shaking table, and flotation, coupled with characterization analysis, were used to assess the concentration response. The results confirmed that particle size and mineral liberation impact the separation process. High recovery and grade were obtained with gravity concentration methods (dense media and shaking table) for coarser (+300 to +212 μm) and intermediate (+150 to +53 μm) particle sizes. Lower recovery and grade were identified for much finer sizes (−53 to −38 μm). Flotation produced a high-grade product at a relatively low recovery and appeared to be only applicable to finer grains. Separation efficiency based on Schulz’s equation measured a segregation performance of 74.8% for dense medium separation and 60.7% for the shaking table for the coarse and intermediate particle sizes. Flotation only achieved a separation of 30%–40%. The results suggest that use of dense media separation as a rough preconcentration method prior to further grinding, and the utilization of a more advanced concentration technique for mineral recovery and upgrade, constitute a successful approach to improve process economics.

Apr 14, 2024