Search Documents

By G. Chisakuta, P. Bwando, G. Mitshabu

By the end of 2022, the south-eastern Copper Belt region of the Democratic Republic of Congo was host to more than 40 small, medium, and relatively large sized copper solvent extraction sites. To date, solvent extraction reagents supplied in this region have never exceeded 50% of ketoxime content. We generated laboratory extraction and strip isotherms and used these with the BASF IsocalcTM modelling software to assess the benefit of using higher ketoxime blends on the main metallurgical performance indicators such as copper recovery and net transfer. Pure ketoxime extractants combine a relatively low strip point and a decent loading capacity, which are most effective as the pH of the pregnant leach solution gets closer to 2.

Jan 1, 2023

By A. V. S. Meyer

The Colloquium held at Iscor, Pretoria, on 28th June, 1988, had as its objective the need for Quality Management Systems in the industry. Case studies of how problems were identified and solved by the use of such systems were submitted.

Jan 1, 1988

By R. Trammell, O. Eterigho-Ikelegbe, S. O. Bada

In response to the enormous amounts of coal discard generated during coal mining and preparation, the development of an efficient and sustainable strategic use of this resource is essential. Furthermore, the rising urban population over the next decades is confronted with the depletion of quality raw materials for building components. To this end, this study reports new information on the morphology, water absorption, and flexural strength properties of ceramic composites produced from three different coal discards and polysiloxane pre-ceramic polymer (PCP) resin. In addition, test results relating to the continuous operating temperature, chemical resistance, and efflorescence potential of the composites are presented. The results show that the water absorption and flexural strength of the coal composites, up to 1.94% and 36.46 MPa respectively, exceed the requirements for ceramic and clay roof tiles. The continuous operating temperature of composites is found to be more thermally stable than conventional roofing tiles (concrete and ceramic) between ambient temperature and 600°C. In addition, the excellent chemical resistance of the composites (94.43%−99.98%) compared to conventional roofing tiles (67.82%−99.97%) eliminates the need for additional external coatings. The interesting results documented so far suggest that this technique could be used to produce low-temperature application building products such as bricks, panels, roofing tiles, etc. This new recycling technique offers an excellent opportunity to eliminate enormous volumes of coal discard and to advance the circular economy in the coal industry.

Aug 2, 2022

By D. F. Malan, J. A. L. Napier

This paper describes some important aspects associated with historical underground measurements in South African gold and coal mines. Deformation measurements were used to confirm the use of elastic theory to simulate the rock mass behaviour in the Witwatersrand gold mines in the 1960s. Although a prominent time-dependent component of stope closure was measured as early as the 1930s, it was ignored owing to the benefit of adopting elastic theory. Neglecting the time-dependent response of the rock for many decades resulted in important aspects such as the effect of mining rate, the effect of advance per blast, and the need for enhanced design criteria not being explored. Recent work is only now starting to address this gap in knowledge. In-situ measurements of large coal specimens in the 1960s and 1970s indicated that a linear formula may possibly be a better approximation of coal pillar strengths. This alternative formulation was never adopted, however, as the power law strength formula was already deeply entrenched in the industry at that stage. In spite of these apparent failures to continuously generate and adopt new knowledge, a key lesson learnt is that major advances in rock mechanics will not be possible without careful monitoring of the rock mass behaviour in experimental sites. Areas requiring further research, such as pillar strength formulae for the Bushveld Complex and enhanced design criteria for the gold mines, can only be developed using extensive undergroundmonitoring programmes.

May 1, 2021

By J. Guerrero, O. Pavez, N. Toro, A. Nazer

In the 19th century, mining in northern Chile was of great economic importance. Today, the ruinsof the copper smelters and abundant fragments of refractory bricks from their furnaces remain. Therefractory materials have not been previously studied. the origin, physical and chemical properties, and compressive strength of 10 different samples of historical refractory bricks collected on-site were investigated. The characterization results showed that the bricks are silico-aluminous, unlike the magnesium-chromium bricks used by current foundries. It was determined that 90% of them were produced in the UK and 10% were manufactured in Chile. The phases present are mullite, quartz, cristobalite, and tridymite, and the chemical composition corresponds mainly to SiO2. The compressive strength of the historical bricks is similart to those currently used,. These results may contribute to the knowledge of the 19th century mining and metallurgical historical heritage of Chile and the UK.

Jul 5, 2023

Notices THE FEDERATION OF SOCIETIES OF PROFESSIONAL ENGINEERS It is expected that the National Institute of Personnel Research will be conducting a project, at the request of the Federation, to establish the relationship, if any, between the academic and professional achievements of engineers. co-operate with the researchers. INFACON 74 The National Institute for Metallurgy, the South African Institute of Mining and Metallurgy, and the Ferro Alloy Producers' Association of South Africa will hold an International Ferro-alloys Congress in Johannesburg from 22nd to 26th April, 1974. INTERNATIONAL PLATINUM SYMPOSIUM OF THE SOCIETY OF ECONOMIC GEOLOGISTS The above symposium is to be held at the U.S. Geological Survey, Denver Federal Center, Denver, Colorado, from 13th to 17th October, 1975. Papers up to 40 doublespaced THIRD MEETING-CANADIAN HYDROMETALLURGYGROUP The Hydrometallurgy Group of the Metallurgical Society, Canadian Institute of Mining and Metallurgy, will hold its Third Annual Meeting, October 1 and 2, 1973, at Edmonton Alberta. COLLOQUIUM ON THE CONSTRUCTION OF SLIMES DAMS The Institute has arranged a two day colloquium on the above topic, to be held on November 14th and 15th, 1973, at Kelvin House. The following Programme has been arranged:

By S. K. Murphy

A partial shaft pillar extraction project was embarked on at a mine in the West Wits mining region in South Africa. Prior to the extraction, a rock engineering assessment was conducted with the main objective being to establish which areas of the shaft pillar could be extracted without unduly affecting the stability of major infrastructure within the shaft pillar. Standard numerical modelling methods were used to conduct this assessment and several areas were identified for extraction. However, during the extraction process, it was found that the infrastructure was affected more than was originally predicted by linear elastic modelling. In addition to this, several large events resulted in far more large aftershocks than would normally be predicted. In order to gain an understanding of this phenomenon, seismic data was integrated with numerical modelling as follows: > The seismic data in the form of displacements was integrated in 3D space within the model to assess the effect of static stress changes associated with seismic activity > Data from large events was integrated onto specific structures, where displacements associated with large events were integrated onto the plane of structure in question. This paper describes the methodology and results obtained from each of the above processes and include insights into the mining process that were previously unfathomable using standard linear elastic numerical modelling. The way forward for this rock engineering assessment of partial shaft pillar extraction is also discussed.

Jan 1, 2012

By M. Z. Emad, A. Hassan, M. A. Raza, M. U. Khan, S. A. Saki

Digital modelling of a surface is crucial for Earth science and mining applications for many reasons. These days, high-tech digital representations are used to produce a high-fidelity topographic surface in the form of a digital terrain model (DTM). DTMs are created from 2D data-points collected by a variety of techniques such as traditional ground surveying, image processing, LiDAR, radar, and global positioning systems. At the points for which data is not available, the heights need to be interpolated or extrapolated from the points with measured elevations. There are several interpolation/extrapolation techniques available, which may be categorized based on criteria such as area size, accuracy or exactness of the surface, smoothness, continuity, and preciseness. In this paper we examine these DTM production methods and highlight their distinctive characteristics. Real data from a mine site is used, as a case study, to create DTMs using various interpolation techniques in Surfer® software. The significant variation in the resulting DTMs demonstrates that developing a DTM is not straightforward and it is important to choose the method carefully because the outcomes depend on the interpolation techniques used. In mining instances, where volume estimations are based on the produced DTM, this can have a significant impact. For our data-set, the natural neighbour interpolation method made the best predictions (R2 = 0.969, β = 0.98, P < 0.0001).

Feb 6, 2023

By R. van Heerden, T. R. Stacey

In the challenging environments of deep-level, narrow tabular orebody gold mines in South Africa, rock mass classification offers a potential method for predicting hazardous areas and optimising rock support systems. This study evaluates the applicability of various rock mass classification systems, with a focus on the Modified or Mining Rock Mass Rating system tailored for high-stress, deep-level mining conditions. Extensive data collection was conducted at Kusasalethu Mine, involving underground mapping and analysis of the 2020/2021 fall of ground database. The Mining Rock Mass Rating system was adapted to the unique geological and operational conditions, providing a simplified, user-friendly approach for rock engineering and geology personnel. Results indicate that this adapted Mining Rock Mass Rating system effectively quantifies rock mass conditions and influences proactive mining adjustments. The study’s findings highlight the system's capability to enhance understanding of rock mass behaviour and substantially mitigate the occurrence of rockfalls and ground collapses. Further application and refinement of the system are recommended to continuously improve mining safety and efficiency.

Oct 24, 2025

By S. Michael, T. E. Moongo

Electrowinning consumes a substantial amount of electrical energy, and owing to the ever-increasing unit cost of electrical power there is a need to improve current efficiency in the process. This research was carried out to design a continuous quality improvement framework for improving electrowinning current efficiency by applying statistical process control (SPC) on an online industrial copper electrowinning operation. A sequential mixed research methodology was applied and a statistical software package utilized for analysing data. It was concluded that metallurgical short-circuits (hotspots) had the most significant effect on current efficiency. Bringing hotspots under statistical control resulted in a 5.40% improvement in current efficiency, which is equivalent to approximately 74 t of 99.999% pure grade A copper cathode production over a period of 1.5 months.

Jan 1, 2021

By D. Paktunc, S. P. du Preez, J. P. Beukes, P. G. van Zyl, A. Jordaan

"The chromium (Cr) content of stainless steel originates from recycled scrap and/or ferrochrome (FeCr), which is produced mainly by the carbothermic reduction of chromite ore. The oxidative sintered pellet production process is one of the most widely applied FeCr processes. The supplier of this technology specifies that recycling of chromite-containing dust collected from the pellet sintering off-gas and fines screened out from the sintered pellets (collectively referred to as pre-oxidized chromite fines) should be limited to a maximum of 4 wt% of the total pellet composition. However, the results presented in this paper suggest that recycling of such fines up to a limit of 32 wt% of the total pellet composition may improve the compressive and abrasion strengths of the cured pellet. In addition, electron microprobe and quantitative X-ray diffraction (XRD) analyses demonstrate that chromite grains present in the pre-oxidized chromite fines consist, at least partially, of crystalline phases/compounds that will improve the metallurgical efficiency and specific electricity consumption (i.e. MWh/ton FeCr produced) of the smelting process. Introduction Stainless steel is a vital modern-day alloy that is well-known for its corrosion resistance, which is mainly due to the inclusion of chromium (Cr) (ICDA, 2013). Stainless steel is mostly produced from recycled scrap and ferrochrome (FeCr), a relatively crude alloy of Cr and iron (Fe). FeCr is predominantly produced by the carbothermic reduction of chromite, a mineral belonging to the spinel group characterized by the unit formula [(Mg,Fe2+)(Al,Cr,Fe3+)2O4] (Haggerty, 1991; Paktunc and Cabri, 1995; Tathavakar, Antony, and Jha, 2005). Although Cr can occur in 82 different minerals, chromite is the only source of new Cr units that can be exploited in commercial volumes (Motzer and Engineers, 2004). Approximately 95% of mined chromite is used in the production of various FeCr grades, of which high-carbon and charge grade FeCr are the most common (ICDA, 2013)."

Feb 1, 2019

By L. Diko-Makia, N. Rembuluwani

Artisanal and small-scale mining is crucial for the mineral sector in South Africa, but it also presents both opportunities and challenges. This paper presents an overview of the South African artisanal and small-scale mining sector, the socio-economic significance of artisanal and smallscale mining, the regulatory environment, and the environmental impacts, which are currently the status quo of this sector in South Africa. The paper identified ways in which artisanal and small-scale mining can support local development, create employment opportunities, and reduce poverty. The case of informatisation, ecological damage, and social insecurity has shown social conflicts, potential land degradation, and criminal behaviour. Finally, the paper discusses the future of artisanal and small-scale mining in South Africa, which will largely depend on improved legislation, enhanced personnel capacity, and more sustainable practices to ensure that the positive outcomes of the industry outweigh the negative ones. These propositions include recommendations to all stakeholders, including the government, industry, and civil society, such as stricter environmental regulations, improved working conditions for miners, and the promotion of responsible mining practices.

Dec 15, 2025

By X. Chen, F. An, H. Chen, Z. Wang

The bottom drainage roadway plays a crucial role in preventing coal and gas outbursts by using underground gas drainage methods. Therefore, it is essential to select the ideal position of the bottom drainage roadway. In this paper use a combination of geological data and numerical simulation to study the ideal position of the bottom drainage roadway, we taking the gas drainage of the first workface of No. 3 coal seam in the Yuxi coal mine in China as an example. The geological study showed a limestone marker layer at an average vertical distance of 14 m from the first mining face. Using this marker layer, the bottom drainage roadway could be excavated without the risk of accidentally exposing the coal seam, and less crosscutting borehole drilling from the bottom drainage roadway would be required. Based on the needs of gas control, the layout of the bottom drainage roadway was selected as an external stagger type. Combined with the numerical simulation results, when located 20 m outside of the mining workface ‘footprint’ on the horizontal projection, the bottom drainage roadway was a sufficient distance from the stress concentration area during mining of workface 1301, which facilitated roadway maintenance. Furthermore, the length of the crosscutting boreholes is also relatively short, which reduces the amount and cost of drilling. The results of this study are expected to provide a reference for the selection of an ideal position of the bottom drainage roadway in field engineering.

May 2, 2022

By M. Z. Naghadehi, E. Emami, J. Sattarvand, R. Battulwar

In this paper, a methodology for a computerised recognition of joint sets on 3D point cloud models of rock masses is presented. The process starts with classifying joints on a 3D rock mass surface through training a deep network architecture and validated using manually labeled datasets. Then, individual joint surfaces are identified using the Density-Based Scan with Noise (DBSCAN) clustering algorithm. Subsequently, the orientations of the identified joint surfaces are computed by fitting least-square planes using the Random Sample Consensus (RANSAC). Finally, the joint planes are classified into different joint sets, and the dip direction and dip angle for each set are calculated. The performance of the proposed methodology has been evaluated using a case study. The results show that the presented procedure is fast, accurate, and robust.

Sep 1, 2021

By T. J. Otto, G. C. Lindeque

Productivity is improved by increasing the ratio of output to input. In an operating open-pit mine, improving the productivity of heavy mining equipment (HME) enables the unit cost of production to be reduced. To optimize HME productivity, the Kolomela open-pit iron ore mine transitioned to an enhanced short-term mine planning (STMP) process that supports the application of a manufacturing-type operating model. At the core of the enhanced STMP process is a focus on integration across the open-pit mining value chain. The interdependencies between mining activities are highlighted and emphasized, thus ensuring that mining activities are synchronized. The improvements related to HME productivity were monitored from 2019 to 2020. The utilization of mining area in the Leeuwfontein pit improved from 71% to 90%, and the blasting frequency reduced by 14% while the average blast size increased by 17%. The distance travelled during shovel relocations between mining phases reduced by 16%, and the lost time associated with drills relocating reduced by 53%. These productivity improvements resulted in an 11% increase in the loading rate of the main waste shovel at Kolomela from 0.9 Mt/month in 2019 to 1.0 Mt/month in 2020. The enhanced STMP process can be adapted to other open-pit mining operations.

Nov 1, 2021

By N. Coulson, P. F. Stewart

The Mine Health and Safety Act No. 29 of 1996, as amended, embeds an occupational health and safety management system that facilitates communication between representatives of the state, capital, and labour. In underground mines, two communication loops between these role players serve to separate the production chain of command from the political tripartite relations. Worker-elected health and safety representatives are involved in both communication loops, but are severely constrained in escalating their occupational health and safety concerns to the legalpolitical level. This has a direct bearing on the exercise of the Right to Refuse Dangerous Work (RRDW). As previously reported, health and safety representatives were found to primarily consult their production supervisors in preference to their trade-union representatives. This follow-up article presents production supervisor perspectives on the RRDW. The study demonstrates how, for mineworkers, the two distinct communication subsystems constrain, rather than facilitate, implementation of the RRDW.

Apr 14, 2024

By Wei Sun, Ruolin Wang, Wenjuan Sun, Junhao Fu, Haisheng Han, Zhao Wei

Pb–benzohydroxamic acid (BHA) (lead complexes of benzohydroxamic acid) exhibits high selectivity but low collecting efficiency in scheelite flotation. This paper reports the manner in which BHA and sodium dodecyl sulfate (SDS) were employed as ligands to coordinate with the lead ions to obtain a colloidal lead-group multiple ligand complex, i.e., the Pb–BHA–SDS, for improving the collecting efficiency of Pb–BHA. The flotation mechanism of Pb–BHA–SDS with respect to scheelite was investigated from the viewpoint of interface science based on the pure mineral flotation, Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. The results showed that the BHA and SDS coordinated with Pb2+ to form novel leadgroup multiple ligand complexes, which are different from the traditional understanding associated with the mixed collectors. Pb–BHA–SDS was a better collector with stronger collecting ability and excellent selectivity in regard to a scheelite flotation than Pb–BHA. The addition of SDS to Pb–BHA enhanced the latter’s adsorption ability on the scheelite surface and improved the hydrophobicity of the collector’s nonpolar groups, rendering Pb–BHA–SDS as a more efficient collector at a low dosage. Keywords: Scheelite; Pb-BHA complexes; sodium dodecyl sulfate; multiple ligands; Pb–BHA–SDS

Jan 1, 2020

By P. Marinos, G. Tsiambaos, H. Saroglou

The anisotropic behaviour of “Athens Schist” has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the “Athens Schist” were statistically analysed and evaluated. Le comportement anisotropique des roches du système “Schistes d’ Athènes” a été déterminé sur des épreuves avec une orientation différente de la schistosité par rapport à l’axe de chargement sous des conditions axiales, triaxiales et dynamiques. Un grand nombre des résultats a été statistiquement analysé et discuté. Zur Bestimmung der anisotropen Eigenschaften der Athen Schiefer wurden einaxialen, dreiaxialen und dynamischen Kompressionsversuchen an Gesteinskernen durchgeführt, bei denen die Belastungsachse verschiedenen Neigungen gegen die Schieferung hat. Die Messreihen an anisotropen unzerreissbaren Fels Samplen von Athen Schiefer wurden statistisch analysiert.

Jan 1, 2003

Termination of membership In accordance with By-Law 7.6.1. of the Constitution of the Institute, the names of the undermentioned members have been removed from the membership register. Colloquium and General Meeting A General Meeting and Colloquium on &apos;Heavy-medium separation and ore sorting&apos; was held on 18th September, 1974, at 09h15, in Kelvin House, Johannesburg.

Jan 12, 1975

By D. Yu, Y. Thibault, D. Paktunc

"Prereduction and flux-aided direct reduction of chromite provide significant advantages in reducing energy consumption and greenhouse gas emissions during ferrochrome production. In this investigation, a comparative evaluation of the influences of several alkali fluxes was carried out based on experimental observations supplemented by advanced material characterization and thermodynamic predictions. Direct reduction of a chromite ore with alkali fluxes at 1300°C for 1 hour produced (Cr,Fe)7C3 type alloys with Cr/Fe mass ratios from 0.7 to 2.3. Among the alkali fluxes, reduction aided by NaOH resulted in a high degree (85%) of Cr metallization with the ferrochrome alloy being Cr4.2–4.6Fe2.4–2.8C3. The formation of liquid slag, which facilitated Cr metallization, was limited by the formation of NaAlO2 between 800 and 1300°C. This, in turn, restricted the collection and transport of the charged ionic Cr species (i.e. O2–) to graphite particles. Under the conditions studied, ferrochrome particles were often small and largely unliberated, which would make the physical recovery of ferrochrome challenging. At 1400°C, the amount of liquid slag increased, enabling the growth of alloy particles. Direct reduction of chromite aided by NaOH is promising as an alternative technology to conventional flux-based smelting in electric arc furnaces. IntroductionConventional smelting processes are energyintensive (Riekkola-Vanhanen, 1999) with the energy requirements greater than 4 MWh/t (Naiker and Riley, 2006; Beukes, van Zyl, and Neizel, 2015), and the greenhouse gas emissions can be significant, exceeding 10.5 t CO2 per ton Cr in ferrochrome produced (International Chromium Development Association, 2016). These include emissions occurring on-site (smelter), emissions due to electricity production, and emissions due to upstream processes. Overall energy requirements are influenced by the degree of prereduction and smelter charge temperature. Significant reduction in electricity consumption can be realized if the charge is prereduced before feeding to the submerged arc furnace (Niayesh and Fletcher, 1986). This consideration has led to the development of several prereduction technologies, with the most important example being the Premus process. In comparison to the conventional smelting processes, this prereduction process lowers the overall energy consumption and greenhouse gas emissions by about one-third (Naiker, 2007)."

Dec 1, 2018