Search Documents

By Jack D. Ramsdell

Electrorefined, magnesium-reduced, and sodium-reduced titanium samples were evaluated for recrystallization behavior, effect of cold rolling on tensile properties, and bend ductility. Curves were determined for the softening of 2.5 to 80 percent reduced cold-rolled metal that was annealed over a temperature range of 300° to 800° C. Upon annealing, coarsening of the grains was found to occur for reductions in thickness of less than 20 percent in titanium made by all three processes. The presence of metallic impurities greatly inhibits coarsening for reductions in thickness below 20 percent, but for reductions in excess of 20 percent grain size is essentially constant at each annealing temperature. The three grades of titanium did not harden excessively from cold rolling; both tensile and bend ductility were good for reduction in thickness up to 80 percent. Upon annealing, softening occurs between 400° and 600° C., and, based on microstructure and property studies, full annealing is accomplished after 30 minutes at 700° C. for the magnesium-reduced and electrorefined titanium and at 800° C. for the sodium-reduced titanium.

Jan 1, 1960

By M. D. Carver

This investigation was undertaken by the Bureau of Nines to determine the effects of impurity levels on the mechanical properties of columbium at low temperatures. High-purity, electron-bombardment-melted columbium was purchased and used as a basis material. Variations in impurity levels were obtained by arc-melting charges containing definite amounts of added impurities. Tensile tests were conducted at low temperatures. Results showed the almost pure basis metal to be ductile at minus 194° C., the lower limit of the range used, Ductility of less pure columbium appeared to depend on interstitial element content. The ductile-to-brittle transition temperature appeared to be raised by increasing carbon content in the range of 50 to 730 parts per million, nitrogen content in the range of 50 to 200 parts per million, or total interstitial element content in the range of 240 to 1,380 parts per million. Some evidence was obtained indicating that decreasing cold work also raised the transition temperature, but recrystallization appeared to have no effect on it. Variations in interstitial element levels appeared to have little or no effect on ultimate strength of columbim in the range of room temperature to minus 194° C, Physical metallurgy studies of massive arc-melted and electron-bombardment- melted columbium were included in the columbium-tantalum research work assigned to the Albany Metallurgy Research Center in fiscal year 1959.

Jan 1, 1961

By J. R. Long

The Federal Bureau of Mines has pioneered the work of preparing ductile titanium on a large scale and has also determined the basic properties of this new and most interesting metal. A number of reports (1, 2, 3: 4, 5) have al-ready been published, and considerable interest has been aroused in a number of industrial and research laboratories. Some of these laboratories have also published results of their work on the pure metal. Although the properties of titanium itself are quite promising, it is apparent that considerable improvement may be expected by alloying titanium with other metals. That is, pure metals in general have shown relatively large improvements in properties when alloyed with other metals and titanium is not considered to be an exception to the rule. Therefore, the emphasis of the investigations now under way in the Federal Bureau of Mines Laboratories has been placed on the study of the alloys of titanium, particularly the titanium-rich alloys. While the main interest is in the properties of such alloys, proper direction and evaluation of the work require at least a rough outline of the phase boundaries of the alloy systems involved.

Jan 1, 1949

By C. J. Thompson

This Bureau of Mines study describes the preparation of sulfur compound concentrates boiling from 225° to 400° C, and reports the sulfur types detected in these concentrates by low-voltage mass spectrometry (LVMS). Existing LVMS methods were extended; the procedures described should be generally applicable to high-boiling petroleum distillates and concentrates as a preliminary means of narrowing the number of factions to be considered for more detailed separation and identification studies. The following major sulfur compound constituents of petroleum are indicated by the data: benzothiophenes, dibenzothiophenes, naphthanothiophenes, naphthenobenzothiophenes, and homologs and isomers of these. Cyclic and chain sulfides comprise a significant portion of the gas-oil range sulfur compound types. The presence of some classes of sulfur compounds containing two sulfur atoms per molecule was indicated.

Jan 1, 1966

By T. A. Evans

The Bureau of Mines conducted a Laboratory and pilot-plant investigation of the flotation of iron sulfides from zinc-lead mill tailings near Platteville, in south-western Wisconsin, at the North Central Experiment Station, Minneapolis, Minn. The procedures used and the results obtained in this investigation are described in this report. Samples for laboratory tests were obtained from each mill in the district, namely, Calumet & Hecla, Inc., Eagle-Picher Co., Vinegar Hill Zinc Co., and Tri-State Zinc, Inc. The sample fat pilot-plant work was obtained from the Davis Mining Enterprises mill.

Jan 1, 1957

By R. J. Heemstra

A continuous flowing paper electrophoresis cell was used to separate petroleum and petroleum extracts into characteristic patterns. The electrophoresis of Bachaquero, Lagunillas, Boscan, and Gibson petroleums in nitro-benzene and acetic acid-based electrolytes was investigated. The extent of separation in the patterns was studied by measuring the metal and porphyrin contents of the effluents. Qualitative separations were achieved in some systems, whereas either system demonstrated only a high degree of electrophoretic migration.

Jan 1, 1967

By P. A. Richardson

The current Bureau of Mines active list of permissible explosives includes 76 brands. Eleven are gelatinous and the rest are the granular type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1970

By J. Ribovich

The current Bureau of Mines active list of permissible explosives includes 71 brands. Eleven are gelatinous, 56 are the granular type, and four are water-gel explosives, an entirely new type of ammonium nitrate-based explosive for use in coal mines. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1973

By W. C. Wahl, M. M. Fine

Leonardite , a naturally occurring , partially oxidized form of lignite with a high content of humic acids , was investigated as a binder for iron ore pellets . Although insoluble in original condition , leonardite forms watersoluble salts with good binding properties when treated with certain alkalis such as sodium hydroxide . Soluble leonardite imparts excellent dry strength to pellets , but green strength is somewhat lower than that obtainable with bentonite . However , green strength can be improved by adding a small amount of calcium hydroxide to the leonardite - concentrate mixture . Leonardite binders were used successfully on three of the four different concentrates tested .

Jan 1, 1964

By A. L. Engel

The Bagdad-Chase copper-gold mine south of Ludlow, Calif., was visited by an engineer of the Bureau of Mines in July 1955 to determine the mine's status of activity and to obtain a bulk sample for metallurgical testing. The deposit was discovered in 1903 and has been worked intermittently. It has a production record of about 273,000 tons of ore. The first production of about 150,000 tons was treated in a cyanide plant 2 miles west of Barstow, Calif. The extraction of gold was not satisfactory because of the presence of copper minerals. Since 1910 the ore has been shipped to various smelters in Arizona and California for use as a flux.

Jan 1, 1957

By A. Viksne

A series of tests were conducted by the Bureau of Mines to determine the best means of reducing noise generated by the detonating cord that is utilized for trunklines in quarry blasting. Ten different types of detonating cord were tested and evaluated for their acoustic qualities. The results of the investigation showed that noise levels produced by "low-core-load-per-foot" detonating cord "not covered" were lower than those produced by "high-core-load-per-foot" detonating cord covered with 6 inches of unconsolidated material.

Jan 1, 1972

By E. G. King

THIRD-LAW entropy data for zirconium-containing compounds are sparse. Kelley a lists entropies at 298° K. for the oxide, tetrachloride, nitride, and silicate, as well as for the metal. The present paper presents heat capacities between 51° and 298° K. and entropies at 298.15° K. for the zirconates of the alkaline-earth metals-calcium, strontium, and barium. The authors believe magnesium zirconate does not exist as a stable compound at room temperature. Entropies of formation from the constituent oxides also are given. MATERIALS The materials used in this investigation were synthesized and analyzed in the Berkeley Laboratory of the Bureau of Mines. Calcium zirconate was prepared by heating an intimate mixture of reagent-grade calcium carbonate and pure zirconia for 30 hours between 1,200° and 1,300° C. and for 32 hours between 1,400° and 1,500° C. As part of the heating schedule, the sample was ground and mixed seven times. Periodic analyses and minor adjustments of composition were made. Analysis of the final product gave 31.19 percent calcium oxide (theoretically 31.28 percent) and 68.67 percent zirconia (theoretically 68.72 percent). The X-ray diffraction pattern agreed with that in the ASTM catalog.

Jan 1, 1960

By J. L. Shultz

The investigation of organic compounds in respiratory coal dust by high-resolution mass spectrometry has shown that the organic components differ (1) with particle size, (2) with rank of coal, (3) in coals of same rank from different coal seams, and (4) in respirable mine dust and respirable coal dust (prepared) from the same mine. The eight respirable mine dusts studied are from coal seams in the Appalachian region where the incidence of coal workers' pnumoconiosis is relatively high. The molecular weights of the major organic components vary greatly among these respirable mine dusts; three show strong concentrations of polynuclear aromatic hydrocarbons.

Jan 1, 1972

By R. K. Koch

The Bureau of Mines developed a zircon sand molding process for static casting of small titanium or zirconium shapes. Castings with unfinished weights up to 3.5 kg (7.7 lb) were produced in an inductoslag furnace and castings up to 7 kg (15.4 lb) were poured in a consumable electrode skull-casting furnace. Molds and cores were made by ram-molding, foundry-grade zircon sand (AFS gfn 93 to 95) bonded by grade D waterglass and tempered with water. Molds and cores were cured either at 250° C (482° F) or 900° C (1,652° F). Castings from the higher temperature molds broke cleanly from the sand while the lower temperature molds produced castings that had to be cleaned by sand-blasting. However, low-temperature cured molds and cores have a number of advantages as follows: (1) A faster, less energy-consuming curing cycle is used; (2) expended cores are water soluble which greatly facilitates core removal; and (3) enough of the binder in crushed expended molds is reactivated by temper water so that the molding mix can be reused five times without any fresh binder additions and up to twenty times without exceeding a total cumulative binder addition of 52 ml/kg dry sand. Crushed used molds that had been cured at 900° C had no detectable binding strength when mixed only with temper water. A large number of oxide and silicate mold washes were studied for improved casting integrity. The most effective wash found for zirconium or titanium casting was monoclinic zirconia (325 mesh).

Jan 1, 1977

By M. J. Lempel

A theoretical study of the heat-transfer characteristics of a dilute gas-solids mixture in an externally heated tube is reported. Detailed equations are developed describing the system, and a numerical method is presented to solve the equations using a digital computer. The methods are applied to a system containing fine coal particles entrained in hydrogen, flowing through a hot tube. Heat-transfer coefficients and several other physical constants are evaluated in detail.

Jan 1, 1967

By Robert E. Meredith, Thomas T. Campbell

An investigation was undertaken to examine the feasibility of employing low- temperature nonaqueous baths for electrodepositing some of the refractory metals of the ferroalloy group . To date , such metals as tungsten , molybdenum , and vanadium have been produced only by high - temperature processes that are technically difficult and sometimes cumbersome in operation . Deposition studies were performed in a wide variety of organic solvents , including amides , ammonia derivatives , ketones , polyhydroxy alcohols , and ethers . Compounds prepared and used as solutes included the chloride and bromide salts of vanadium , tungsten , and molybdenum . Studies were conducted over a temperature range of 20 ° to 200 ° C under inert atmosphere . Conductivity and current potential data were obtained for all baths that contained reasonable solute concentrations . Qualitative solubility data were obtained for compounds of ferroalloy metals in a variety of solvents . In general , all solutes showed low solubility in ethers and ketones but reasonable solubility ( in excess of 20 grams per liter ) in alcohols , amides , and ammonia derivatives . No successful metallic deposits that would encourage further study were obtained with any of the systems that were examined .

Jan 1, 1963

By F. P. Haver

The Bureau of Mines is developing a leach-electrolysis procedure to produce Special High Grade (SHG) zinc from sulfide concentrate without the generation of sulfur oxide gases. Chlorine-oxygen leaching of the concentrate yields zinc chloride (ZnCI2) which, after purification, is electrolyzed in a fused-salt cell to obtain molten zinc metal and chlorine gas for recycle. This paper describes a laboratory-scale investigation made to develop a procedure for electrowinning zinc metal from ZnC12. Zinc chloride by itself is not a suitable electrolyte because it fumes badly above its melting point and is a poor conductor of electricity. Other salts therefore must be added to prevent fuming and improve the conductivity. Optimum results were obtained with a KC1-LiCl-ZnCl2 bath at 500° C, using a current density of 5 amp/in2 and an electrode spacing of 0.5 inch. Under these conditions, SHG zinc was produced at a current efficiency of 94.3 pct and an energy requirement of 1.16 kwhr/lb. Fused-salt electrowinning eliminates the need to handle and melt cathodes and increases the production of metal per unit cell volume through the use of higher current densities than are possible with aqueous electrolysis.

Jan 1, 1976

By Stephen D. Hill

The Bureau of Mines devised and constructed a modified Knudsen effusion apparatus, permitting a constant measure of the weight of effusing vapor, to determine the equilibrium vapor pressure of metal halides at temperatures up to 1,200° K and over the pressure range 10-5 to 10-2 torr. The reliability of the apparatus was established by determining the vapor pressure of potassium chloride. After correcting for partial dimerization of the vapor, data obtained on solid KCl between 750° and 950° K can be expressed by the following equation:

Jan 1, 1966

By C. C. Popoff

The development of glass-making industries in the Pacific Northwest as well as other industries that use pure silica has been retarded by lack of local supplies of low-cost raw material. Several quartz deposits along the Skagit River constitute the only known source of relatively pure silica within the range of cheap transportation to the Seattle industrial area. Although some silica has been mined from these deposits, very little information regarding their size, grade, and other physical characteristics has been available to the general public. As a part of its program of investigation of the mineral resources of the Pacific Northwest, the Bureau of Mines assigned the writer to examine the Skagit River silica deposits in October 1946. This report presents the factual data obtained from an examination of the so-called Stoner, Bacon Creek, and Pressentin deposits. These deposits are the largest and most easily accessible known to exist in the area. The deposits are near Marblemount, which is on State Highway 17A. They are within 1 mile to 1-1/2 miles of the Skagit. River Railway, which provides transportation to Seattle, a distance of 130 miles. None of the deposits has been developed thoroughly. The Stoner deposit, however, has been developed by a quarry about, 5,0 feet square and has been exposed by hydraulic removal of the overburden throughout a distance of 180 feet along the hanging wall of the vein

Jan 1, 1949

By E. G. Erspamer

Laboratory investigations were made by the Bureau of Mines on ore containing the sulfides of both mercury and antimony to develop a method or methods for the economic recovery of mercury metal and the concurrent recovery of antimony as metal or salts,. If standard mercury-recovery techniques are applied to such ores, the antimony content interferes with the effective production of mercury metal; further-more, the antimony is lost. This report presents the results of tests on a sample of cinnabar-stibnite ore from the Red Devil mine near Sleitmute, Alaska. Red Devil ore was chosen for the investigation because it is purported to be typical of ores of the Kuskokwim River area, which, in their aggregate, constitute large potential reserves of mercury and antimony. Studies included petrographic, spectrographic, and chemical analyses, gravity-separation tests, bulk flotation of mercury and antimony sulfides, differential flotation, leaching, and furnacing of crude ore and of flotation concentrate.

Jan 1, 1956