Search Documents

By Vernon C. Davis

In initial attempts to mine taconite by conventional open-pit methods, the material tended to break into tabular blocks that were too large to be handled by conventional shovel dippers and were unsatisfactory in an ordinary crusher feed. A great amount of secondary blasting was necessary, which added considerably to the cost of mining. The Bureau of Mines and others are engaged in studies designed to contribute to the solution of taconite-mining problems. These studies concern problems related to drilling techniques and patterns, types and methods of use of explosives, and other factors relative to effecting maximum fragmentation at minimum cost. This report, is concerned with study of the application of shaped charges in drill holes, the effectiveness of shaped charges as compared to capped charges in secondary blasting, and the merits of different drilling patterns and methods of detonation of conventional-explosive charges. Fragmentation of taconite at or near the surface is controlled or strongly influenced by joint and bedding planes. Since all tests in this study were made in a jointed and bedded area, a definite conclusion as to the relative effect of a shaped charge in a drill hole, as compared to a conventional charge at greater depths and tighter ground, is precluded. However, application of shaped charges in primary blasting of taconite appears to be of no advantage. In secondary blasting of taconite, conventional, capped charges produced better breakage than shaped charges of the designs tested. Based on the results of conventional blasting practice in horizontal-, inclined-, and vertical-hole tests, no better fragmentation is obtained from blasting either horizontal or inclined holes, compared to vertical holes. Holes drilled in staggered parallel rows that intersect both series of joint planes at the greatest possible angle, give maximum breakage compared to rows paral-lel to one of the series of joint planes. Methods of detonation made little difference in breakage; but the milli-delay caps produced the best conditions for moving the broken rocks.

Jan 1, 1953

By R. HOLROYD

The Ludwigshafen and Oppau plants are largely independent I. G. factories situated some 23 miles apart on the west bank of the Rhine facing lannheim. The former factory is a general organic chemical works specializing in dyes, dye intermediates, plastics and synthetic rubber,. while the latter is a heavy organic chemical factory producing ammonia, methanol, higher alcohols and their derivatives. Before the war much of the I. G. research and development work was carried out at Ludwigs- hafen; in particular the high pressure research section directed by Dr. Mathias Pier played a very active part in all hydrogenation developments. Apart from the possibility that a full scale hydrogenation or Fischer Tropsch plant had been erected at Ludwigshafen/Oppau during the war, the main objectives of an oil team investigation were: - (a) To obtain from Dr. Pier and his staff an advance general picture of German fuel production processes. (b) To study the fuel developments still in the research and pilot plant stage. (c) To examine any new developments in hydrogen or synthesis gas manufacture. (d) To look for new processes for production of high anti-knock fuel constituents and for new fuel additives. (e) To investigate new chemical syntheses based on raw materials obtainable from oil. The Ludwigshafen and Oppau factories were first visited by the large team listed in Appendix A during the period 25-31st March. The investigation revealed that no large plant for synthetic fuels or lubricants had been operated at this target. All the important members of the Fuel Research Section staff had been evacuated to Heidelberg and information on the work of this department was therefore limited to that contained in seized documents, the greater part of which have still to be examined in detail. Valuable information on synthesis gas production from hydrocarbon gases was obtained as well as interesting data on a num- ber of chemical syntheses. Two members of the above team Holroyd and Faragher accompan- ied by Major Tilley (interrogator) went on to Heidelberg, contacted Dr. Pier and the chief members of his staff on April 1st and obtained from them the hydrogenation information given later in the body of the report. Later, after visiting Leuna, Holroyd, Faragher and Ellis paid a second visit to Heidelberg and to Ludwigshafen/Oppau on 27th-30th May to check a number of details, particularly with respect to hydrogenation costs, and to obtain information on the pressure.conversion of water gas to hydrogen and on the manufacture of Wickel pressure vessels.

Aug 1, 1943

By J. P. Connell

The U.S. Bureau of Mines awarded a contract to Morrison-Knudsen, Inc., to evaluate the use of roadheaders in underground mining operations. Road-headers were found to be widely used in mines as construction support units, as development miners, and as stoping machines. However, road-headers were found to have mechanical and electrical problems, to suffer reduced productivity when integrated into the mining cycle, and to create dust problems. Also high capital costs and low utilization and avail-ability cause high amortization costs per ton. This report identifies the roadheader operating problems and offers suggestions for improved mechanical and electrical design as well as manufacturer and owner responsibilities for improved availability. The development of a complex integrated excavation and ground support sys tern is no t warranted until the roadheader itself is made much more reliable.

Jan 1, 1980

This report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the ore handling stream. Oversize ore causes much additional labor, creating work stoppages and is a principal cause of accidents in metal mines. This report includes data on block caving, back cut and fill room and pillar, shrinkage stoping, and sublevel stoping.

Jan 1, 1974

In 2005, a total of 7,111 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA). ? Sand and gravel mines were the largest mining sector, comprising 48.5% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Sep 1, 2008

By Lars Skogsberg

Work with hand-held power tools can be found in most industries all over the world. This type of work exposes the operators to different kind of loads like gripping-forces, feed-forces, exposure to vibration and noise, holding hot or cold surfaces and the exposure to dust. Designing a power tool with good ergonomics is a matter of finding the best compromise. As a simple example, increasing the mass is not acceptable because it will increase the forces needed to handle the tool. At the same time increased mass will in most cases reduce the vibrations. Vibration disorders related to the use of hand-held power tools has been known and reported since long. It is therefore essential that low vibrating tools are developed and used. The new vibration regulations in Europe, based on the Physical Agents (Vibration) Directive, have put increased focus on the vibration control in industry. Forces acting on the tool cause vibration Tools for industrial use must be of very robust design to withstand the very hard use they are exposed to. Industrial tools are therefore normally designed with the main parts made of metal. From a vibration point of view this means that most tools can be regarded as rigid bodies, especially because the dominating frequency normally is equal to the rotational frequency of the tool spindle or the blow frequency for a percussive tool. These frequencies are with few exceptions below 200 Hz. Handles however can not always be regarded as rigidly connected to the tool. There are several examples of weak suspensions designed to reduce vibration transmitted to the hands of the operator. There are also examples of designs where the handles just happened to be non-rigidly connected and in some cases even in resonance within the frequency region of interest. Oscillating forces act on the tool and the result is vibration. Design principals In all cases forces are the source of vibration. This leads to the three basic principles to control vibration: • Control the magnitude of the vibrating forces. Examples are the balancing unit on a grinder or the differential piston in a chipping hammer. • Make the tool less sensitive to the vibrating forces. Examples can be when the mass of the guard on a grinder is rigidly connected to the tool to increase the inertia of the tool. • Isolate the vibrations in the tool from the grip surfaces. Examples are vibration-dampening handles on grinders or pavement breakers, the air-spring behind the blow-mechanism in a riveting hammer or the mass spring system in a chipping hammer.

Jan 6, 2006

By Diana K. Schimmelpfennig

Assessment of revegetation success on mined lands is a difficult, time consuming task and has been the subject of a number of controversies. Present regulations require that both plant cover and aboveground plant biomass be measured for use in making that assessment. Of these two variables, biomass is the most time consuming to measure and requires destructive sampling, a most undesirable requirement on fragile, recently revegetated areas. On the other hand, plant cover can be estimated using the point-frame method which is relatively nondestructive. In addition, vegetation can be sampled more uniformly with the point frame and in less time if species composition measures are to be made. A study was done to evaluate the predictability of aboveground biomass production on revegetated mined sites and adjacent native prairies using plant cover estimates made with the point frame method. The predictability of biomass production by cover estimates bears on the need for both measurements in assessing revegetation success. In general, a positive, statistically, significant correlation was demonstrated between plant cover (estimated by the point frame) and aboveground biomass (estimated by the harvest method) regardless of community type (mined or native), species composition, diversity or level of biomass production. However, the latter did have their effects on the relationship and must be accounted for in any predictive equations (that is to say, the predictive equations must be considered site-specific). Considering the relationship observed between the two parameters, cover estimation may be a sufficient indicator of revegetation success, especially where time and minimization of disturbance are critical.

Jan 1, 1982

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958

By Lloyd L. Farnham

This paper is one of a series describing the mineral resources of the Nation, including location, history, production, ownership, geologic setting, and mining methods for most of the known manganese deposits in New Mexico, With few exceptions these descriptions are the result of field examinations by the writer. Of 32 counties, the 12 which occupy the western half of the State contain all the known manganese deposits, These counties are Catron, Dona Ana, Grant, Hidalgo, Luna, Rio Arriba, Sandoval, Santa Fe, Sierra, Socorro, San Juan, and Taos. (See fig. 1.)

Jan 1, 1961

By L. A. Neumeier

A refinement of the tungsten-cobalt phase diagram is presented for compositions to 85 at. pct cobalt and for temperatures to the solidus. Preparation of alloys by powder metallurgy methods is described, and the results of studies made by a combination of techniques involving microscopy, X-ray diffraction, thermal analysis, and dilatometry are discussed. The existence of u-W6Co7 is confirmed (rhombohedral D85 structure). The W6Co7 phase forms periectically at 1,685'115° C by reaction of liquid with primary W; the peritectic melt is at 71 at. pct cobalt. The homogeneity range of u-W6Co7 extends to both sides of the ideal stoichiometric ratio, through a compositional range of about 5 at. pct. The compositional limits for u-W6Co7 vary slightly below 1,471°±5° C, the temperature of the eutectic reaction forming u-W6Co7 plus a. The eutectic composition is at 79 at, pct cobalt. The existence of WCo3 is confirmed (hexagonal D019 structure). WCo3 forms peritectoidally at 1,093°±5° C by reaction between a and u-W6Co7 and exists over a narrow homogeneity range of 0.5 to 0.6 at. pct. The solid solubility of cobalt in tungsten is low (maximum 0,9 at, pct cobalt) and results in contraction of the tungsten lattice. Tungsten is extensively soluble in a-Co at higher temperatures; the a-Co lattice is expanded by the presence of tungsten in solid solution. There was no indication of the formation of a o-phase nor of any intermediate phases other than WeCo7 and WCo3. The WeCo7 and WCo3 phases are compared with similar phases in other systems.

Jan 1, 1967

By D. A. Paice

Direct current electrical systems are used in most coal mines primarily to power the main haulage trains and secondarily to feed other equipment and passageway lighting. Electrical power is supplied from rotary machines or static rectifier equipment and is distributed through the mine by open trolley wires and feeder cables. The rails of the haulageway are used as a current return path. This exposed power distribution system is very vulnerable to conditions which lead to undesired leakage currents and short circuits and, consequently, the possibility of fires or other hazards to personnel. Present techniques and equipment have been utilized in so far as practical to improve the safety of the dc electrical system; however, there still appears a need for further improvement. Because of this need, this program was sponsored by the Bureau of Mines to investigate two specific technical areas related to improvement of dc electrical system safety. One area included the determination of the characteristics of mine electrical systems and their protection requirements and the verification of the adequacy of available protective devices for mine service. Despite the widespread application of industrial protective equipment in mines, there was little detailed technical information available related specifically to the performance of this equipment in service. Our task was not only to develop useful information regarding mine system protection, but also to define and verify the adequacy of the protective devices available. The second area of investigation called for development of a practical technique for detecting low level electrical fault or leakage currents. Conventional protective devices

Jan 1, 2012

By J. K. Whyatt

During the past 2 years, U.S. Bureau of Mines (USBM) researchers reviewed an in situ stress investigation conducted in 1977 at a test site on the 4250 level of the Lucky Friday Mine, Mullan, ID. Although the field measurements of over core strain were found to be useful, significant deficiencies were found in the stress field estimation procedure. The stress field estimate was then updated to incorporate recent progress in statistical capabilities and new understanding of stress concentration factors for doorstopper cells, as well as to correct an error in the original stress solution procedure. Simple models were used to examine the possibility that systematic variations in material properties and stress fields existed at the site. These models succeeded in reducing the sum of squared error somewhat, but fell short of completely describing stress variations throughout the test site. This overcore measurement will be supplemented by two other measurements described in the second and third reports of this series. Other observations of stress field characteristics are discussed in the fourth report The final report will also characterize the natural in situ stress field in the vicinity of the Lucky Friday Mine. This work was undertaken to support USBM research on mining method design and rock-burst control for deep mines.

Jan 1, 2010

By Frank J. Wiebelt

Under a general program to extend the resources of mineral deposits, the Bureau of Mines examined the Quien Sabe antimony mine in October 1948. The preliminary evaluation demonstrated that a diamond-drill program was warranted co establish the tenor and persistence of the veins and permit an estimation of antimony reserves. The Bureau of Mines conducted a diamond-drilling program on the property from December 1949 to May 1950. Ten holes aggregating 2,483 feet were drilled. Nine of the holes encountered antimony-bearing vein material.

Jan 1, 1956

By Lloyd Williams

1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sewanee, has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although same coal has been produced from them. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By D. E. FOCG, A. E. Wells

When the United States entered the World War governmental agencies found little definite knowledge available as to the exact capacity of each sulphuric acid plant in the United States to manufacture acid under the stress of a great emergency. It is true that on account of the demand for acid for the manufacture of munitions for the Allies, prior to the entrance of this country into the war, most of the acid plants near industrial centers in the Eastern and Northern States were running at or nearly their maximum capacity, but, . for various reasons, many plants in these States and plants in other districts were not. For a number of years statistics as to the production of acid by the plants of the country were compiled by the United States Geological Survey, but obviously such figures did not give information as to the maximum capacities that might be available for meeting the he.a vy war ·requirements, or as to the steps that would have to be taken to bt-ing these capacities into use. During the summer and early fall of 1917 various attempts were made to obtain the desired information, but no satisfactory or complete data were obtained. Late in 1917, under the authority granted to the Bureau of Mines by the explosives act, the Director of the Bureau of Mines directed A. E. Wells, metallurgist of the bureau, to uiake a complete survey of the situation. Mr. Wells personally conferred with officials of the acid companies and visited most of the acid plants in the North that are east of the Mississippi River. The information obtained through this personal survey, together with that obtained through the ready cooperation of the subcommittee on ncids, and the subcommittee on fertilizers of the Committee on Chemicals of the Council of National Defense, enabled the preparation of a report containing the desired data concerning the sulphuric acid industry. This report was made immediately available to the War Industries Board and to those offices in the War and Navy Depart- ments that were most directly concerned in planning the explosives program and in obtaining the necessary supplies to produce the explosives. Beginning with this survey and report, the sulphuric acid section of the war minerals investigations of the Bureau of Mines took an active part in all matters pertaining to the sulphuric acid industry during the remainder of the war. Mr. Wells, the chief of the section, was appointed an associate chief of the sulphur, pyrite, and sulphuric acid sections of the War Industries Board. .Also, by this direct contact with the War Industries Board, the data obtained by Messrs. R. R. Hornor, H. A. Buehler, a.nd 0. Lindstrom, who were in charge, for the bureau, of the investigations concerning the supplies of pyrite and sulphur, were constantly made available to all interested Government agencies. D. E. Fogg, of New York City, was appointed chemical engineer to the sulphuric acid section to make special investigations relating to the acid industry, especially the possible utilization, in an emergency, of those sources of raw material.not then being used. Mr. E. E. Corbett, of Brooklyn, N. Y., was appointed chemical engineer to make investigations concerned primarily ,vith the conservation of acid. Direct and intimate contact with the industry was had through the close cooperation with the committee on acids of the Chemical Alliance, this committee during the greater part of 1918 occupying rooms with the acid section of the bureau. With the ending of the war and the close o:f the active work of the acid section of the bureau, the suggestion was made by many interested parties that a bulletin be prepared giving some qf the fun. damental and most important facts regarding the sulphuric acid industry, including a discussion of the technical :features of the manufacture of acid. During the war the bureau received -a vast number of inquiries in regard to various phases of the industry, a.nd this fact also made such a bulletin seem desirable. Therefore, the present bulletin was prepared to cover the main facts in regard to the industry in this country, including a discussion of the supplies of sulphur-bearing raw materials, the situation of the acid plants, the principal points in regard to manufacturing processes, and the uses of the acid. No attempt has been ma.de to discuss at length the manufacturing processes, as details differ more or less at the different plants and in general are carefully guarded by the acid ·companies. A great deal of the data given in this bulletin may be found in various pub]ications, but this is the first publication in which such data have been assembled and made readily available. Most of the data were obtained directly from observation and from cooperating acid companies or from individuals who had been or are now engaged in acid manufacturing and were liberal and generous in making their information available for publication. Care has been exercised to publish no data that were obtained as confidential by the bureau's representatives. The average acid manufacturer may be already more or less acquainted with most of the information presented in this bulletin, yet it is believed that the bulletin will be of value to those who wish to obtain a. general review of the present condition, both the economic and technical, of the sulphuric acid industry in the United States.

Jan 1, 1920

By Lincoln A. Stewart, P. S. Haury

"INTRODUCTION AND RESUME Arizona asbestos mines are the only sources on the American continents of iron-free chrysotile spinning fiber that meets the Navy specifications for asbestos fiber for use in covering electrical cables. Rhodesia normally supplies the bulk of this grade of asbestos at about half the Price of Ari zona spinning fiber. The acute submarine menace in 1942 focused attention on the danger that imports might be cut off and that a sudden demand for greatly expanded production might fall on the Arizona mines to supply the tonnage of this essential material needed for war production.A joint preliminary investigation of Arizona asbestos deposits was made in August 1941 by J. R. Thoenen, senior mining engineer of the Bureau of Mines and A. E. Granger, a geologist of the United States Geological Survey. A more extended investigation of the numerous asbestos mines and prospects, which are scattered over 25 townships of difficult terrain in Gila County, was begun by the senior author in August 1942.The Geological Survey assigned two geologists (Newton Chute and A. F. Shride) a few weeks later to study the geology as an aid in selecting the mines for the Bureau's exploration projects. Six mines were selected for exploratory work because it was desired to prove reserves of ore where production could be started quickly if urgent demand should arise. Acceleration of production is normally slow because of adverse operating conditions. First, the mines are at distances of 35 to 100 miles from Globe, the shipping and supply point, and the roads are few and poor. The mine openings start in steep canyon walls, so that mining supplies usually have to be packed in and the product packed out over 0.5 to 5 miles of burro trail. Second, most of the ore deposits are small, and the ratio of rock broken to spinning fiber recovered is very high, usually exceeding 200."

Aug 1, 1947

In 2006, 14,885 mining operations reported employment data to the Mine Safety and Health Administration (MSHA).1 Almost half (48.2%) were sand and gravel mines, followed by stone mines (30.7%), coal mines (14.2%), nonmetal mines (5.0%), and metal mines (1.9%).

Jan 1, 2008

By T. D. Hackett

Multislice mining methods were analyzed by the U.S. Bureau of Mines to determine their application to western United States thick coal seams; ground control, geology, and costs were considered. Multislice mining is used in widely varying seam conditions worldwide, including flat seams too thick to mine in a single pass, pitching thick seams, and seams containing a rock parting. Longwall multislice methods predominate, but room-and-pillar variants also exist. The initial use of the method in western seams is planned at a deep Colorado mine where a rock parting will be used to separate two slices mined by longwall. Ground control and spontaneous combustion are major hazards associated with multislice mining. A well-consolidated upper slice gob can reduce ground control problems and provide a seal against spontaneous combustion. Geologic analysis indicates that the consolidation of the gob depends on the composition of the upper slice roof, the presence of water, and sufficient overburden pressure. A geologically competent intermediate rock parting can also reduce ground control problems and seal against spontaneous combustion. To compete in western coal markets, the cost of multislice mining must be within the range of normal longwall costs. Analysis indicates that multislice operating costs should be within this range, and that multislice mining costs decrease as panel width increases. Relatively wide (600 to 800 ft) panels also provide increased coal recovery.

Jan 1, 1990

By H. E. Harris

It has long been recognized that one of the principal ways of combating dust in coal mines is by means of water sprays. However, spray systems, currently in use, clog or plug frequently, thereby reducing the effectiveness of dust control aid, in turn, possibly increasing the health hazard to mining personnel. Moreover, the maintenance and replacement of spray system components, e.g., nozzles and filters, can be expensive in terms of direct costs of labor and material, and the consequent loss of production. Recognizing these problems, the Bureau of Mines sponsored a research project on the "Development of a Non-Clogging Water Spray System"; this project was carried out by Eastern Associated Coal Corp. The overall objective of this project was to develop a non-clogging water spray system suitable for use in underground coal mines. Since most of the dust formed is at or near the working coal face, emphasis was placed on face equipment such as a continuous mining machine. To accomplish this objective, a two-phase project was carried out. The first phase involved determining the causes of spray nozzle and spray system clogging, determining the availability of spray nozzles or systems that could be modified to be non-clogging, and developing a non-clogging water spray system. Phase two was concerned with the fabrication and the laboratory and field testing of a non-clogging system. In each phase, there were both laboratory and field investigations, and the results of these investigations are presented in this report.

Jan 1, 1975

By Y. Miron

'This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, g the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2).

Jan 1, 2010