Search Documents

By F. Göktepe

Flotation gases and conditioning of the pulp with them are one of the important parameters of flotation and should be taken into account especially in the flotation of sulphide ores. In this study, flotation of pure chalcopyrite and pyrite samples were investigated with air, oxygen and nitrogen as flotation gas and the effect of conditioning with these three gases also were performed. Flotation gas was introduced for 5min, 10min, 15min and 20 min. For chalcopyrite flotation there was no drastic change in recovery when air, oxygen and nitrogen were used as flotation gas but conditioning the pulp with oxygen for 10 minutes increased the recovery about 8% where pulp potential has been approximately 25 mV with chalcopyrite and 150 mV with platinum electrodes. Conditioning with all three gases decreased the pyrite recovery by about 20% with 20 minutes conditioning. Pulp potential decreased in the presence of nitrogen while conditioning with air and oxygen increased the pulp potential for both electrodes. Generally potential increased for both minerals with oxygenation and aeration time but it was stable or slightly decreased with nitrogenation. Comparison of the gases showed that the different flotation gases do not effect flotation recovery but conditioning the pulp with these gases at pre-flotation effects chalcopyrite and pyrite flotation recovery, most dramatically pyrite.

Jan 1, 2014

By M. Surracco, M. C. Tilocca

"Mineral comminution is often a costly process which also requires high level of energy. In the course of the studies carried out by the researchers of the Department of Civil-Environmental Engineering and Architecture at the University of Cagliari, aiming at the optimization of the reduction processes, it has been experimented, among of others, the effects of high-speed water jets on minerals grinding. As far as coal is concerned, some of the solutions initially adopted are presented in this paper, which essentially relied on the water jet power only, with secondary use of mechanical actions, to reach the most modern solutions that envisage the use of mechanical energy, normally used in traditional grinding machines, in synergy with hydraulic energy transferred by water jet.INTRODUCTION Mineral comminution can be rather expensive and demand a high-energy consumption, especially for fine sizes (Austin, 1979). Further interesting perspectives in this area may be offered by comminution means aided by high pressure water jets (Ciccu 2007), whose crushing potential is currently used for several operations such as cutting different materials, rock digging and industrial cleaning. The crushing action of water jets may induce a traction stress in materials where substances of a mineral nature, especially if characterised by permeable porosity, oppose a minor resistance (Griffith, 1920). The first solutions to this purpose essentially relied on the sole energy of water jets, with a secondary use of mechanical actions (Ciccu, 1993). Results were encouraging, despite the high values of specific energy for the low capacity of treatment. However, due to the difficulty in making the techniques mainly based on hydraulic energy practically applicable to solids comminution a solution was experimented, with some interesting results, consisting in the combination of mechanical energy, normally used in traditional grinding devices, with hydraulic energy transferred through water jets, in a synergic relationship (Ciccu, 1998; Tilocca, 2016)."

Jan 1, 2018

By M. D. Vilarinho, W. Xuan, F. Vasconcelos Guimarães

"This article summarises the efforts to reduce the energy consumption in grinding in a magnetite ore beneficiation plant. ArcelorMittal Kryvyi Rih ore beneficiation plant produces magnetite concentrate at 65% Fe and 8% SiO2, of which the D80 is approximately 44µm after three stages of grinding with ball mills and magnetic separation. Characterisation and laboratory scale bench tests performed on samples from the beneficiation plant indicate that the industrial flowsheet could be simplified. After the first stage of grinding and magnetic separation, a significant size fraction of the intermediate concentrate is already well liberated. Therefore, it can be directly concentrated in a second stage magnetic separation without further grinding. If a screen of 150µm size can be implemented after the first stage of grinding-magnetic separation, only the oversize of screening, representing 35% of the material, requires secondary and tertiary grinding and magnetic separation. The combined concentrate from the two fractions already meets the industrial specifications. This new route can provide the same final product, with fewer mills; it saves around 30% in energy consumption only in the grinding step without changing the main structures of the processing plant.INTRODUCTION Comminution, including crushing and grinding, is responsible for at least 40% of total energy usage in mining and mineral processing. This paper shows an example to reduce grinding cost, by changing the flow sheet design strategy in ArcelorMittal Kryvyi Rih (AMKR).AMKR is one of the most important mining and steel complexes in Krivoy Rog basin in Ukraine, which has been studied over 100 years because of mining of iron ores. The iron ores are associated to Banded Iron Formation of the Saksagan suite, with an average iron grade of around 36 percent Fe. The total thickness of the Krivoy Rog Supergroup reaches 5-6 km, whereas that of the iron-ore Saksagan Group comprises up to 1400 m. High-grade iron ore extends to more than 2,000 m below present surface"

Jan 1, 2018

By Ricardo Montero

At this time, over 300 tons of Au are used in electronic equipment each year with other precious and strategic metals such as Ag, Pt, Pd, Cu, Nb, Ta, etc. After the use-phase, the electronic devices become electronic waste (e-waste); consequently it is important to consider e-waste as a secondary supply for recovery of these metals. One of the most important components is the printed circuit boards (PCBs) because the amount of their precious metals is ten times higher than rich precious metals bearing ore. This paper presents the recovery of Au, Ag, Cu and Nb from PCBs of discarded computers using leaching column technique. The amount of these metals in used PCBs was: 613 g/ton of Au, 1515 g/ton of Ag, 36 g/ton of Nb and 23.4 % of Cu. The PCBs were crushed with a hammer mill until reaching a particle size between 3.33 mm to 0.43 mm. Then, it was leached with sodium cyanide solution in a glass column using the following conditions: sodium cyanide concentration 4 g/L, flux 20 L/kg PCBs day, pH between 10.5 to 11 and leaching time 15 days. Every day, after leaching, the pregnant solutions passed through a column with activated carbon to complete the closed loop system. The following recoveries were obtained: 46.6% of Au, 51.3% of Ag, 47.2% of Nb and 62.3 % of Cu. The products obtained are: a) loaded carbon that contains the desired metals and b) processed PCBs with precious metal contents. A preliminary technical-economic study shows the feasibility to create a small-scale PCBs recycling plant. The initial investment is on the order of US$ 155 639, considering the recovered metals from loaded carbon. The internal rate of return for 10 years period (IRR) and net present value (NPV) estimated are 27% and US$ 105 926 respectively. Keywords: printed circuit boards, recovery, precious metals, niobium, leaching column

Sep 1, 2012

By Mauricio Guimarães Bergerman

At the regrind or secondary grinding stages of base metal ores, the concern about energy efficiency is usually extremely important. In general, the specific energy consumption at this stage is higher than during the primary grinding stages. In addition, a tendency of finer grinding has been observed in the new projects of metallic minerals, due to the finer mineral liberation, which leads to increasing capital and operational costs. At Vale?s new copper projects in Brazil, regrind sizes with a P80 of approximately 40 to 20 µm have been necessary. Conventional ball mills, adequate for primary grinding, usually bring about low energy efficiency with products bellow 50 µm. Vale is using the vertical mill on its copper projects ? Sossego and Salobo, in order to optimize the regrind of rougher concentrates and reduce energy consumption. This paper presents the results of industrial surveys carried out on the Vertical mill circuits of Sossego plant during its initial years of operation, and compares these results with the design criteria and laboratory regrind tests used for the mill scale up. Keywords: grinding, regrinding, copper, vertical mill, stirred mill

Sep 1, 2012

By Y. De Gao, C. Gang Zhong, X. Yang Qiu, Li Wan

The chelating reagents are used as effective collectors in wolframite flotation, and certain metal cations need to be added using chelating collectors so as to activate valuable minerals and obtain good flotation indexes. Different metal cations will result in different reactivity with collectors, in order to select the effective activator in BHA flotation of wolframite, the activation effectiveness of different metal cations on wolframite ((Fe,Mn)WO4) flotation were studied using pure minerals. The results showed that the wolframite activation by Pb2+was the best among the selected cations. The maximum flotation recovery of wolframite was found to be 95.58 % under conditions of 100mg/LBHA and 1×10-4mol/L of Pb2+at pH 9. The dosage of Pb2+needs to be controlled in an optimum range. Also, the activation mechanism of Pb2+ on BHA flotation of wolframite was investigated by measurements of contact angle, zeta potential, adsorption capacity and IR spectroscopy. It was found that Pb2+ could chemically adsorb onto the wolframite surface improving the flotability of wolframite and enhancing the adsorption of BHA on wolframite. When the dosages of BHA and Pb2+ were 100 mg/L and 1×10-4 mol/L, the adsorption quantity of BHA on wolframite sharply increased up to 0.30 mg/L at pH 9 compared with wolframite treated with only BHA.

Jan 1, 2014

By N. P. Haran

A detailed study was undertaken to beneficiate sub-grade iron ore sample from Kenojhar District, Orissa, India containing 57% Fe (T), 7.7% SiO2, 4.8% Al2O3, 4 % L.O.I. 0.4% TiO2,1.3 % Mn and traces of S(T) to make it suitable for the user industry. The mineralogical study indicated that it predominantly consists of haematite with subordinate amounts of goethite and clay. Quartz, Cryptomelane / Psilomelane, Pyrolusite, Gibbsite, Feldspar and Muscovite mica were present in very minor to trace amounts. The Denver grind ability tests indicated, that the sample could be categorized as ?medium soft to medium.? The Bond ball mill work index was determined to be 14.19 kwh per short ton. The beneficiation process involved classification followed by tabling of the classified sand, ground to minus 48 mesh size. The table slimes were subjected to Wet High Intensity Magnetic Separator (WHIMS). The developed process yielded a composite concentrate from tabling and WHIMS operations assaying 65% Fe(T), 2% SiO2, 1.8% Al2O3, 2% Mn and 0.9% LOI with a recovery of 60.1% Fe (T), amounting to 52.5 wt.% yield. To meet the size specifications for pellet making, it was further ground. Dewatering studies were also carried out on the ground combined concentrate and rejects. The thickener area of ground combined concentrate using 0.02 kg/t of Sufloc A 1115 flocculant was 0.02 m2/tonne of dry solids per 24 h. And for the combined rejects using 0.12 kg/t of flocculant, it was 0.035 m2/tonne of dry solids per 24 h. The moisture content, in the pressure filtration cake, in the ground combined concentrate product was 10.0%, and productivity was 506.7 kg/m2h. Thus, by thickening and filtration of process products, 90% of water used in the process could be recovered. The study highlights the development of a simple and cost effective flowsheet with almost complete water recovery for a subgrade iron ore sample. Keywords: tabling, WHIMS, thickener, filtration

Sep 1, 2012

By Robin B. Batterham

"Since the 1970?s we have seen a marked corporate response in terms of the environment. In part this has come from regulation but it has largely come from stakeholders and the community. Rising expectations have in general been met. We now see a similar trend towards sustainability. At the same time, the importance of mining to the share market has decreased drastically and with that decrease has come the requirement for the mining sector to show returns similar in manner to other sectors. While rationalisation can achieve some progress towards these goals, the long-term requirement is for innovation, as it always has been. This paper looks to the logical goal of innovation within a sustainable mining framework and targets the removal of the desired metal values with minimal environmental footprint. It is suggested that broad ranging alliances will be necessary, particularly amongst the R&D suppliers, to achieve this goal. Industry will need to take an active role given the recent global restructuring.THE MARCH TO SUSTAINABILITYSince the 1970?s there has been an increasing corporate response on environmental matters. We have moved from matters environmental being issues relevant only to minority groups through a series of attitudinal changes by management. Whilst there have always been examples of excellent environmental performance, for many in the 70?s spending money on improving the environment beyond some minimal level was seen as a distraction from production or treated in a similar way to donations to the community. There is little of that attitude these days, as most mining companies have long since regarded the environment as a core business direction. Indeed, for some years one could note an escalation in matters of environmental reporting to the extent that the environmental performance of companies is now very public. In some cases, NGOs have even been invited to help certify and audit the reporting standards. Similarly with health & safety.There is now a rising expectation on the part of the community that social matters will also be given the same level of support as health, safety and the environment. This time around it would appear that the mining industry is at the leading edge of sustainability. The Global Mining Initiative (Global Mining, 2002) and the contributions to the Rio World Summit on Sustainable Development (Rio +10, 2002) suggest that sustainability is being taken very seriously by the mining industry. For sustainability it is convenient to use the Brundtland (1987) definition. This definition has widespread acceptance with governments, industry, environmental groups, financial institutions and individuals as a direction against which our activities and plans can be measured."

Jan 1, 2003

By Venkataramana Runkana, Aditya Pareek, Vishnu Masampally, Nagaravi Kumar Varma Nadimpalli

"Recovery and grade of the ore produced are two important metrics, which define the profitability of a mineral processing plant. Achieving high grade and high recovery at the same time in a mineral processing plant is difficult due to conflicting nature of the two objectives. To explore the operability limits of the plant operations and find the set of operating conditions that can help achieve the best possible recovery and grade, there is a need to solve a multi-objective optimization (MOO) problem. Past research focused on building a plant-wide simulation model or on optimization of individual units or a part of a mineral processing plant like grinding circuit, crushing circuit, etc. However, it is necessary to consider optimization of the complete plant in order to optimize the plant performance. Here, we have formulated the mineral processing plant performance optimization as a MOO problem. We have applied machine-learning algorithms such as random forest to build models to predict the recovery and grade of the ore. A non-dominated sorting-based multi-objective evolutionary algorithm called NSGA-II (Non-dominated Sorting Genetic Algorithm II) was employed to solve the MOO problem. Since the number of parameters that influence recovery and grade are quite large, we have applied machine-learning algorithms for feature selection or identification of key process variables. Pareto optimal conditions were determined for manipulated variables like grinding mill throughput, speed ratio at SAG mill, speed of centrifugal pump, water addition at different locations etc. The results obtained are useful in identifying the operability of a mineral processing plant to achieve the optimum grade and recovery for a given feed grade and the processing circuit. INTRODUCTION Copper is majorly mined or extracted as copper sulfides from large open pit mines in porphyry copper deposits. Among all the available ores, sulfides are the most commercial ores, especially chalcopyrite (Greenwood and Alan, 1997). Copper grade in these ores generally lies between 0.4 to 1.0%. In order to perform smelting operation, the grade of copper has to be improved to around 30% (Biswas et al. 2013). This targeted copper grade is achieved through two stages of mineral processing. Firstly, the copper in the ore has to be liberated by crushing the mineral rock. Secondly, the liberated copper in the crushed ore is then physically separated from other minerals like nickel by froth flotation techniques."

Jan 1, 2018

By X. P. Guo

In this paper the test results of flotation of the kyanite ore from a Chinese mine are described. The objective of this work is to determine effective recovery process to obtain kyanite concentrate with high quality and high recovery for a new concentrator design. The valuable minerals of the ore are kyanite, garnet and magnetite, contents of them are 14.0%, 5.9% and 1.2%, respectively. The gangue minerals are mainly biotite, feldspar and quartz, contents of them are 33.8%, 17.8% and 25.6%, respectively. The kyanite in the ore contains a little iron. In laboratory flotation tests the factors affecting the flotation such as slime, alkalinity of pulp, and flowsheet configuration are studied. The interference of biotite on kyanite flotation as well as selective flotation of garnet is examined. On the basis of above-mentioned results the flowsheet of ore treatment comprising de-sliming, mica flotation, low intensity magnetic separation of magnetite, high intensity magnetic separation of garnet and coarse biotite as well as flotation of kyanite is pre-sented for comprehensive recovery of kyanite, garnet and magnetite. The kyanite concentrate con-taining more than 59% Al2O3 is obtained with a kyanite recovery of 70.0%. The contents of Fe2O3and biotite in kyanite concentrate decreased from 2.02% and 5% to 1.30% and 1%, respectively. The disadvantage of low kyanite grade in raw ore is compensated by accessory recovery of garnet and magnetite in the ore.

Jan 1, 2014

By M. L. Cao

In this study, a montmorillonite organo-intercalation compound (MOIC) was synthesized by using a Na-modified bentonite (NaB) as a matrix and hexadecyltrimethylammonium (HDTMA) bromide as an intercalating reagent under microwave irradiation. The synthesized products were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), organic carbon content measurement, and adsorption density determination. The results show that, at 10% suspension concentration and 10 minutes irradiation in a 130-W microwave oven, the basal spacing d(001) of the synthesized MOIC increases to 2.209 nm from the original 1.218 nm of NaB. The MOIC has much higher adsorptive densities to nitrobenzene and aniline from aqueous solution than the NaB. The adsorption isotherm of nitrobenzene on the MOIC is linear, and the adsorption is mainly the result of nitrobenzene?s preferred partition in MOIC over aqueous solution due to MOIC?s hydrophobicity. The adsorption isotherm of aniline on MOIC follows the Freundlich equation and the increased adsorption is not only the result of aniline?s preferred partition in MOIC over aqueous solution but also that of the MOIC?s surface adsorptions.

Jan 1, 2014

By A. R. Hasankhoei

Water recycling is of prime importance in mineral processing due to consumption of large amount of water. This issue is vital in areas with a low rainfall such as Shahre-Babak (Kerman, Iran). Deep cone thickeners, unlike conventional thickeners, have a low diameter to height ratio where large amounts of flocculants are used to increase particles settling rates. The high bed heights (over 10 m) produce enough pressure to create a paste type underflow indicating maximum water recovery. Flocculent preparation, conditioning, and distribution along with the bed height are among the important factors affecting the performance. Four deep cones are used to recover water from the tailings of the plant. Plant data indicated that the thickener never reached the target underflow percent solids (63%) and the average underflow concentrations were between 49 and 57%. By modification and optimization of flocculent preparation and distribution methods the underflow percent solids increased by 3-4%. This translated to an increase of water recovery from 67 to 73%. This was equivalent of 53000 m3 saving in monthly water consumption. Keywords: deep cone thickener, water recovery, flocculant, copper tailings

Sep 1, 2012

By Antony Amberg, Gonzalo Saldías, Romke Kuyvenhoven, Catherine Souza, Heriban Soto, Francisco Soto

"Vizcachitas is an advanced stage copper–molybdenum porphyry deposit, fully owned by Los Andes Copper and located in Central Chile. The property contains an indicated resource of 1,038 million tonnes grading 0.37% Cu and 0.012% Mo, and an inferred resource of 318 million tonnes grading 0.345% Cu and 0.013% Mo (Coffey & Alquimia, 2014). The deposit occurs in the same geological belt as several other giant copper-molybdenum porphyry deposits including Río Blanco-Los Bronces, Los Pelambres-Pachon and El Teniente. In 2018, the original Preliminary Economic Assessment (PEA) study from 2014 was updated; this paper presents the geometallurgical testwork that was performed to support that update. The testwork focused on the metallurgical characterization of 40 DDH samples and the development of a more profound orebody knowledge by relating geological features with metallurgical performance. The scope of work included complete chemical and mineralogical QemSCAN characterization; SAG, ball mill and abrasion testing; complete rougher and cleaner kinetics including locked-cycle-test; environmental ABA and settling tests on rougher tailings. The results show that the ore can be classified as medium-hard, with a hardness that is slightly below the average for large Cu/Mo deposits in the region. A good correlation was found between lithology and breakage characteristics, implying that the specific energy consumption (kWh/t) is well correlated to rock type. The results of the flotation tests were very encouraging and did not show significant variability. An overall Cu recovery of 91% can be expected for the flotation circuit. The use of a relatively coarse primary grind size gave good final recovery and grade for both Cu and Mo, and deserves further attention in future work, as this impacts positively both energy consumption and water recovery.INTRODUCTION Los Andes Copper Ltd. is a Canadian exploration and development company focused on the acquisition, exploration and development of advanced stage copper deposits in Latin America. The company owns 100% of the Vizcachitas project in Chile, the largest copper deposit in the Americas not controlled by the majors. Vizcachitas is a copper-molybdenum porphyry deposit, located 120 km north of Santiago, in an area of very good infrastructure."

Jan 1, 2018

By Zhou Junwu, Han Long, Song Zhenguo, Sun Chuanyao

The deposit genesis, the ore property, and the mineral characteristics, which has a close relationship with the beneficiablity, could be regarded as the “Genetic Properties”, actually are the determining factors for beneficiation process development. However, in conventional concentrator’s process development and engineering, there have been lack of systematic research and test on those genetic properties, also lack of well-established collecting, statistics and analysis system for those huge amount of data such as the historical mineral processing technique research, process mineralogy study, practical operating and engineering data. Obviously it is far less than enough for profound integration combining modern IT together with traditional mineral processing technology, as a result there are a number of disadvantages in mineral processing R&D and engineering, such as long term, high cost, low efficiency as well as repetitive testwork not making full advantage of previous experiences. Aiming to make utmost of those Genetic Properties and overcome above disadvantages in mineral processing R&D and engineering, the concept of “Genetic Mineral Processing Engineering (GMPE)” is put forwarded, and the strategical study has been conducted on this regard, with the main focus on following aspects: a) Testing and extraction of the “Genetic Properties”; b) Establishment of data base and data warehouse of GMPE; c) Intelligent decision making system for beneficiation process; d) Verification testwork; e) Virtual concentrator. The technical route proposed is to firstly conduct research and test on those Genetic Properties mentioned above, based on that the specific data base will be set up and applied for intelligent process recommendation and simulation with a few verification testwork conducted in the meantime, finally achieve a fast, high efficiency and precise determination of technology and process for ore beneficiation. The systematic study on the three-in-one GMPE would make an innovative breakthrough in conventional mineral process testwork research and engineering methodology, and provide technical support for the concentrator’s design and upgrading.

Jan 1, 2018

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"Expert Online is a software system that makes use of novel artificial intelligence technology, known as the Interpreting Expert System (IES), to mimic an informed expert on a minerals processing plant. Previous implementations of the IES were only capable of explaining the controller actions. Expert Online will also take on the more difficult task of explaining the complex process behaviour to the operator in simple language.The primary functions of Expert Online are to serve as a training tool and an online assistant to operators. However, it is also expected to be of value to supervisors and plant managers.A number of additional features are envisaged, including different operating modes, fault detection, speech synthesis and advanced message filtering. Expert Online will increase the operator’s knowledge of the process and his/her understanding and acceptance of the complex control systems. Users would be supplied with relevant and timeous information required to make informed decisions to ensure smooth plant operation.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

By Susanna G. de Jager, Francis W. Petersen

"The aim of the project was to develop a methodology applicable to different South African coal types to be able to predict with a high degree of certainty what kind of reagent will be suitable for flotation of a certain coal type.The study included 5 coal samples from different collieries and included Highveld seam 3 and 4 coal (as one sample), Waterberg coal (zone 10 -11), Highveld seam 5 upper coal and Witbank seam 2 and seam 4 coal. Seam 3 and 4 (mixture) coal, Waterberg and the seam 5 upper coal were all found to be vitrinite rich coals. The coal characterisation study included petrographic analysis, proximate analysis, float-sink analysis, oxygen-containing functional groups, surface extraction, flotation release analysis and contact angle measurements.The flotation tests showed that the best reagents to float all of the coal samples studied are iso-decanol and dodecene. These reagents produced flotation products that are near to the release curve. Statistical relationship for predicting ash content and yield that can be expected for a certain coal type and selected collector was obtained. From the relationship, the accuracy of the yield is above 95% (p-value below 0.05) with a linear regression of 0.9289. The accuracy of the ash is slightly lower with a linear regression of 0.7841 but also above 95%."

Jan 1, 2003

By J. A. Venter

Mineralogical studies indicate the Pt-Pd-Bi-Te class to react poorly on the flotation stimuli and indications are that these minerals are slow floaters. However, recent studies performed on a number of minerals from this class indicated strong interactions with potassium ethyl xanthate resulting in the formation of dixanthogen (only one of several xanthate species). The poor flotation response is not a result of poor interaction of xanthate with the surface. It is proposed that the oxidation products of sulfides in the process water interact with the PGM surface. To test this, the effect of thiosulfate (an important oxidation product of sulfides) was investigated by employing electrochemical measurements and FTIR spectroscopy. The electrochemical investigations indicate no strong effect of thiosulfate on the interaction of xanthate with the minerals surface as well as the reduction of oxygenthiosulfate is likely not responsible for the poor flotation response of these minerals in industrial plants.

Jan 1, 2014

By Indrajit Paul, Atanu Pal, Kapil Modi, Sanjay Chandra, Chandra Sekhar, Srinivas Dwarapudi

"High alumina content in the Indian iron ore fines (2.5% Al2O3) resulted in poor quality pellets at the recently commissioned 6 MTPA pelletizing plant and a study was under taken to establish suitable pellet chemistry through proper fluxing agents. Limestone fluxed pellets were prepared at varying basicity (0 to 0.8) and pyroxenite fluxed pellets at varying MgO contents (0 to 3%) to study their effect on the metallurgical properties. Fired pellets were tested for their strength, RDI, reducibility and swelling. Microstructural studies, optical and SEM-EDS, were carried out to quantify different phases and their chemistry. Acid pellets exhibited poor quality whereas limestone pellets at 0.8 basicity and pyroxenite pellets at 1.5% MgO exhibited optimum metallurgical quality. Formation of widely distributed silicate melt in limestone pellets and high melting point slag & magnesioferrite in pyroxenite pellets found to improve their quality. However during commercial production of MgO bearing pyroxenite pellets, their room temperature and low temperature properties found to be inferior, but exhibited better high temperature properties, viz. softening-melting behavior. Contrary to this, commercially produced limestone pellets, comprising CaO, exhibited better strength and RDI but showed poor high temperature properties. To yield the benefits of both CaO (for good strength and RDI) and MgO (for low swelling and high softening), a dual flux combination was established by using both limestone and pyroxenite/olivine together that resulted in optimum metallurgical properties. Coke rate at the blast furnaces found to be reduced by 1kg for every1% increase of dual flux pellets in the burden.INTRODUCTION Iron ore agglomerate quality plays a vital role in decreasing the reducing agent consumption and increasing the productivity of blast furnace. In most of the integrated steel works, the burden mix for blast furnace is decided as per the availability of the iron ore agglomerates like sinter and pellets. More attention has been given in recent years to the use of fluxed pellets in blast furnace due to their good strength and improved reducibility, swelling and softening melting characteristics. Generally, quality of pellets is influenced by the nature of ore or concentrate, associated gangue, type and amount of fluxes added and their subsequent treatment to produce pellets. These factors in turn result in the variation of physicochemical properties of the coexisting phases and their distribution during pellet induration. Hence properties of the pellets are largely governed by the form and degree of bonding achieved between ore particles and the stability of these bonding phases during reduction of iron oxides (Panigraphy et al., 1990). It is important to note that conditions and parameters of pelletizing are specific to given ore or concentrate; the present study is undertaken for typical Indian hematite ore fines high in alumina. Except authors earlier work on quality of pellets from Indian iron ore (Dwarapudi et al., 2008, 2010), there is no considerable literature reported on the effect of pellet basicity and MgO content in the basicity range of 0 to 0.8 for Indian hematite ore."

Jan 1, 2018

By R. P. Bhagat

The paper reports results on sinterability of iron ores from the mines of Tata Steel Limited. The objective was to improve tumbler index (TI) of sinter and its reduction parameters, reduction degradation index (RDI) and reducibility (RI) while maintaining strand productivity same or to improve. Pot sintering experiments were carried out with Joda and Noamundi mines having LOI 3.8% and 2.9% respectively. Sinter basicity (CaO/SiO2) was varied in the 2.1 to 2.5 range and its MgO content was kept in the 1.4% to 1.8% range according to the blast furnace requirement. The ignition condition and vacuum was maintained according to the plant practice. The effect of variables namely, granulometric composition of ores vis-à-vis that of sinter mix, bed height, solid fuel, moisture content of green mix on the sintering indices was studied. The productivity with Noamundi ore (26 %+6.3 mm) was lower than that with Joda ore (45% +6.3 mm) at 4% coke in the mix and sinter basicity (CaO/SiO2) 2.1. However, with 4% coke (ash 22%) the RDI value was significantly high in case of Noamundi Ore, which decreased significantly to 29% with 5% coke. The size parameter of ore fines and its LOI content do influence the sintering speed and the sinter properties significantly. At 2.1 basicity ratio, the sinter with the Joda ore having coarsergranulometry had highest TI (=70.2%). The RDI (27%) in this case was inferior to that (23.2%) when Joda ores with finer size was sintered. Better RDI with finer sized ore could be attributed to better assimilation of CaO/ MgO with more balanced and uniformly distributed hematite minerals. The size parameter has been inter-influenced by the coke requirement. With the lower mean sized Joda ore the sinter RDI decreased significantly to 23% and the productivity improved to 42.9 T/(sq m*d) when the coke in the mix increased from 4% to 5%. An attempt to reduce the coke in the mix from 5% to 4% with respect to both the ores was not successful as it resulted higher RDI and lower strand productivity. The present study has revealed that sinter RDI improves (decreases) with decrease in the sintering time, while such correlation was absent between TI of sinter and speed of sintering. Corollary to this observation, one can take advantage of other stronger parameters to increase the sintering speed (and hence sinter productivity) without affecting the sinter strength. In the present study higher FeO sinters has displayed excellent RDI, however cold strength of sinter was not correlated with its FeO content. The TI and RI parameters of sinter improves marginally with increase in its MgO content while RDI got worsened. Keywords: LOI content, iron ore, reduction properties, sinter, noamundi, joda

Sep 1, 2012

It is well known that the crushing and grinding steps in the mineral processing of ores represent a substantial proportion of total energy, cost and carbon emission in mining. For instance a recent study calculated that 36% of the energy consumed by gold and copper producing mines in Australia was attributable to comminution (Ballantyne et al, 2012). Understanding this component of a business is essential in a world seeking to lower production costs, improve earnings and reduce its carbon footprint. The issue commands the attention and support of industry leaders in the mining sector, government, equipment manufacture, engineering design and research organizations. Furthermore, several researchers have often stated that globally, comminution processes consume between 3-4% of the world?s electrical energy production (Daniel and Lewis-Gray, 2011). In 2009-10, Australia?s Federal Government Energy Efficiency Opportunity (EEO) participants in the mining sector used 336.5 PJ, representing approximately 6 percent of Australia's total energy use. It is evident that the current practices of breaking rocks in tumbling mills are relatively inefficient (Fuerstenau and Abouzeid, 2002). Research and improved engineering design has established that a range of improved blasting, crushing and grinding techniques and flow sheets may lower project costs and carbon footprint. These include relatively simple process flow sheet strategies such as gangue rejection or pre-concentration prior to size reduction, a better combination of grinding technologies (both current and new systems), and selection of coarser grind sizes where ore and waste mineralogy allow. Yet, despite this systematic and detailed research, the industry remains somewhat reluctant to implement these strategies. CEEC (Coalition for Eco-Efficient Comminution) was established in 2011 to support knowledge sharing and change in an area of high-energy consumption for the global mineral industry. CEEC is a not-for-profit industry company, funded by grants from world wide industry companies, whose mission is to accelerate knowledge and technology transfer in the field of energy-efficient comminution. The key benefit to the mining sector arising from CEEC?s activities will be an increase in the rate at which more energy-efficient comminution data sets, processes, and technologies are developed, demonstrated, shared and applied. This will contribute directly to the industry?s target of reducing operating costs and carbon emissions. CEEC International Ltd and JKTech Pty Ltd teamed together to facilitate the inaugural CEEC Workshop, in June 2012. The purpose of the workshop was to produce a roadmap to provide guidelines for how (1) operations can achieve best EEC practice in the short to medium term, in collaboration with vendors, engineering companies and other service providers, and (2) what R&D is needed to achieve paradigm change in EEC in the medium to long term, e.g. 75% reduction in comminution energy in 10 years.

Sep 1, 2012