Search Documents

By Volker Vogt, Wolfgang Sand, Eberhard Gock

"For about 20 years, the use of bacteria to control the flotation process for the production of raw material concentrates has been the subject of worldwide scientific and engineering efforts. The objective is to reduce the consumption of biologically non-degradable toxic reagents. The principle idea is to use the activity of bacteria in natural leaching processes – known since the middle of the last century – for controlling flotation processes.It was discovered that the selective activity of bacteria during the extraction of raw material concentrates by means of flotation could also be achieved with extracellular polymeric substances (EPS), excreted by bacteria. EPS, which is extracted by means of centrifuging bacterial cultures, can help to significantly reduce the use of cyanides, approximately 200,000 t/a are used for ore dressing today.The bacterium used was Acidithiobacillus ferrooxidans. In order to identify the bandwidth of the oxidation activity, 21 bacterial strains of the strain collection of the University of Hamburg were attracted to iron(II) sulfate and pyrite under defined conditions. All strains oxidized iron(II) sulfate ten times faster than pyrite.EPS has so far been derived from four strains. In general, EPS extracts are divided into a hydrophilic and a hydrophobic fraction. The hydrophilic fraction is composed of e.g. fucose, rhamnose and glucose; fatty acids such as dodecanoic acid, hexadecanoic acid, octadecanoic acid and nonadecanoic acid were found in the hydrophobic fraction. Pure mineral phases and mineral mixtures were used for the flotation tests. The outcome was reproducible results with technical flotation machines. The research results known so far are mainly based on investigations with micro flotation devices, which are usually used for the characterization of reagents and which do not allow a direct translation to the technical scale."

Jan 1, 2003

By Seoul National University, Ki-Ho Kim, Jong-Pyo Kim, Sung-Min Joo, Hee-Chan Cho, Hyung-Seok Kim

Aragonite was synthesized in addition of Mg2+ ion and SrCO3 seed by carbonation process, and the best condition and mechanism of the synthesis was studied by analysis of continuous pH change, ICP, XRD, and SEM. As MgCl2•6H2O addition increased, aragonite phase increased at condition of CO2 flow rate of 100 mL/min and stirring rate of 250 rpm. It was the dissolution of Mg(OH)2 that determined overall reaction time. As SrCO3 seed addition increased at 0.2 mole MgCl2•6H2O, the amount of aragonite increased and the aspect ratio was from 5 to 9. And it was thought that Mg2+ ion prohibited calcitetransformation of aragonite formed by SrCO3.

Jan 1, 2003

By O. Güven

In recent years, there is an increasing demand on manganese consumption which stems from the important role of manganese in carbon steel production. And the growing need for manganese ores makes the beneficiation of low-grade manganese ores more economical. In this study, the characterization and beneficiation studies were carried out to propose a flow sheet for typical low-grade Turkish manganese ores. For this aim, different gravity separation methods were applied. According to the mineralogical analysis, the major mineral phases are pyrolusite (MnO2) and psilomelane (MnO2) while the major gangue mineral is radiolarite. Gravity separation tests were accomplished by using jigs, shaking table, MGS (Multi Gravity Separator) and in order to obtain products with high Mn ratio, high intensity magnetic separation was also performed. As a result, different combinations of flow sheets were utilized and a concentrate assaying 56.5% Mn with 85 % recovery was obtained.

Sep 1, 2012

By A. P. Chaves, D. Jose Neto, M. G. Bergerman, E. S. Mano

"More complex ore comminution and concentration operations have found increasing application in the mining industry due to lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. They allow removing a significant mass of material with little or no content of the relevant mineral before the ore is fed into the processing plant, with the consequent reduction in the mass to be processed in downstream operations. Significant benefits arise out of the use of pre-concentration, such as higher contained metal output without the need to increase the grinding or flotation capacity, and longer mine life. The grade of marginal ores could be enhanced to a level that would make their exploration economically feasible, which would result in increasing exploitable reserves. Nevertheless, few studies to date have assessed the resulting impacts on ore grinding energy consumption and wear after the gangue is removed through pre-concentration operations. This study evaluated the energy consumption and wear of grinding circuits in Brazilian mining operations in which the feed has gone through a pre-concentration stage. Such assessment was based on different samples of sulfide and oxide ores. Laboratory tests were carried out to investigate the power consumption and wear of grinding circuits with and without a pre-concentration stage. Laboratory test results were used to simulate industrial grinding circuits based on both alternatives and illustrate the environmental and economic benefits of each one.INTRODUCTION Increasingly complex ore concentration operations in several stages have found broadening application in recent years in view of lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. Different ore processing technologies can be used for that purpose, such as magnetic separation, density segregation, and separation methods based on high-tech sensors (ore sorting). Currently, the most common methods are gravimetric processes, in view of their low cost, particularly jigging and dense medium separation methods, such as the drum and cone separators manufactured by Western Machinery Company, Teska, Drewboy, Norwalt, Dynawhirlpool and Tri-flo, and dense medium cyclones (CAMPOS; LUZ; BRAGA, 2010). The use of dry ore sorters has also grown significantly in recent years (Jose Neto et al. 2017). The selection of the separator type depends essentially on the ore particle size, required flows, and operating density ranges. All these methods may even be used after preferential blasting in mining (Grigg & Delemontex, 2015)."

Jan 1, 2018

By U. A. Peuker, T. Mütze, F. Shayo, A. Wikedzi

"Buzwagi Gold Mine (BGM) is operated by Acacia Mining and located in the Lake Victoria Goldfields of central Tanzania. The mine treats a sulphide copper-gold ore to produce gold in form of doré bars and a concentrate containing gold, copper and silver. The BGM comminution circuit includes a primary crushing stage with a gyratory crusher and two grinding circuits using a Semi-Autogenous Grinding (SAG) mill and a ball mill. Currently, the grinding circuits are inefficient in achieving the aspired product fineness of xP,80 = 125 µm even at low to normal throughputs (450-600 t/h). An optimization study of the circuit performance was conducted to improve product fineness through circuit surveys, experimental lab work and simulations. The analysis of survey data revealed inefficient grinding operation characterized by ball mill product (xP,80 > 400 µm) coarser than designed and higher hydrocyclone cut sizes (xT > 200 µm), too. In MODSIM several options were simulated such as reduction of vortex finder and apex diameters, reduction of SAG screen aperture, and modification of cyclone feed density. An improvement of product fineness could be achieved by simulation of the cumulative changes but it was also concluded that the current equipment cannot achieve the target. Further simulations showed that a second ball mill might help to achieve the desired fineness as well as an increase of grinding throughput by up to 26 %. INTRODUCTION Simulation of comminution, particularly grinding and classification, has received great attention for many years, due to the fact that the unit operation is by far the most important both in terms of energy consumption as well as overall plant performance (King, 2001; Wills et al., 2006). The use of simulation is advantageous due to low cost as well as its ability to consider many variables simultaneously. Moreover, there are some benefits for optimizing grinding operations by simulation like decreased unit operating costs, increased capacity, and improved performance of downstream processes due to improved feed size distribution. This paper presents an optimization study for the grinding efficiency at Buzwagi Gold Mine. This was achieved through three full scale circuit surveys, lab work and simulations with MODSIM."

Jan 1, 2018

By D. R. Nagaraj

The traditional (popular) approach to reagent development and optimization, which has become entrenched in both research and practice for many decades, is highly reductionistic, incremental and costly, does not produce robust chemical solutions, and is not sustainable. There are also several other key drivers and changes in the mineral industry that clearly warrant a new approach. In response to these, an intense effort was made at Cytec over the past fifteen years to develop a meaningful, efficient, and sustainable approach to develop new reagents and robust chemical solutions in mineral separations. This effort culminated in three important outcomes: a) development of the holistic approach, called FLOTATION MATRIX 100? process, b) novel reagents, and c) enhanced application knowledge for reagents. In this paper, the efficiency, utility and power of the holistic approach will be demonstrated with examples using both existing and new reagents in the processing of Cu-Au, Au and Cu-Mo ores.

Jan 1, 2014

By Nicholas Enraght – Moony, Alvin Johns, Zhonghan Zhang, Zhang Xianhua, T. Choo

"The tungsten (WO3)-rich ores from King Island Scheelite (KIS) Mine, Australia, containing scheelite(CaWO4) were previously recovered by gravity separation and flotation of fine scheelite (1978-92) with an overall recovery of 76% when both circuits were operating. Recently extensive test work has been conducted both in China and in Australia on KIS ores, assaying from 0.50%-1.34%WO3, and tailings assaying 0.2%WO3(GZRINM 2009; 2011a; 2011b). A new approach, which aimed at improving both recovery and grade of concentrate by means of an innovative all flotation route WOF (Whole Ore Flotation), achieved excellent results: 90%-92% recovery to concentrate grade of 66%-70%WO3for the ores. The process is characterized by the use of selective reagents in flotation, including a newly developed collector for scheelite, GYWA. The WOF process also embraces the "Improved Petrov Method" in the cleaning of scheelite rougher concentrate. Earlier investigations found that the removal of sulfides by flotation prior to scheelite flotation was not necessary. It was also found that recycling of process water did not influenceresults. Two main ore types were tested as well as tailings from 2009to 2001(0.20%WO3). In addition a flow sheet using wet high gradient magnetic separation (WHGMS) in tandem with flotation was also investigated for the tailings."

Jan 1, 2014

By Grant C. Lukey, Jannie S. J. van Deventer

"The environmental effects of the mining and mineral industry include destruction of natural habitats, changes in river regimes and water tables, and other serious ecological impacts. In this century, it is likely that water will become a critical resource, and in most countries the mining industry competes for a share of this resource. The Kyoto Protocol may at first seem only relevant to the coal mining and power industry, however, it should not be forgotten that the mining and mineral industry is a significant consumer of power. Therefore the ratification of the Kyoto Protocol by most developed countries and the introduction of a carbon credit trading scheme will impact on the industry by potentially increased costs in utilities and waste discharges. It is clear therefore that the mining industry faces many challenges in the coming years. The mining industry?s commitment to sustainable development needs to continue to evolve, in order to meet these challenges effectively. With the advent of globalisation of the industry, it is now an opportune time for the industry to gain international agreement on how they want the industry to achieve sustainability in future years; such a progressive approach is necessary, otherwise government will force the industry to change, which may not necessarily be the best outcome for the industry.INTRODUCTIONThe Earth Summit in Rio de Janeiro in 1992 was an opportunity for world leaders to assemble and discuss strategies and initiatives that provide for further industrial growth without adverse effects on the environment. The World Summit on Sustainable Development held last year in Johannesburg, South Africa, was an opportunity to evaluate those initiatives implemented over the past 10 years, and to set a new and sustainable direction for the future. It is clear that industrial and technology development will continue at a rapid pace in order to serve the needs of a growing world population, but it is essential that the course of this development is well planned, well executed, and that it is sustainable. In reality, while government officials and politicians continue to debate policy and international protocols, the environment continues to suffer and the effects of climate change and global-warming become more real each day."

Jan 1, 2003

By S. M. Javad Koleini

Processing of phosphate ore sample was investigated for increasing phosphate content and reduction of its gangue minerals such as carbonates and silicates. Experimental designs were per-formed using Taguchi method. Different flotation methods were investigated for Moundon phosphate ore sample and three methods were used as follow: direct cellophane flotation, reverse calcite flotation and reverse quartz flotation. Because of the sensitivity of cellophane flotation to slime content, prior desliming was carried out before the experiments. Direct flotation experiments carried out and a concentrate contained 23.80% P2O5, 6.88% SiO2 and 72.33% recovery were produced. The achieved P2O5 content in the produced concentrate from reverse flotation of calcite was 26.44% and the recovery was 82.56%. The concentrate products obtained at optimum conditions by direct flotation of phosphate and indirect flotation of calcite were subjected to indirect flotation of calcite and direct flotation of appetite and final concentrates with P2O5 grade of the order of 24.19% and 26.96% were obtained, respectively. It was concluded that one stage direct flotation is unavoidable to achieve a product with low SiO2 content.

Jan 1, 2014

By P. Braga, A. Chaves, S. França, A. Luz

"In Brazil, there are no official reserves of molybdenum, and the unofficial reserves are modest. Therefore, the molybdenum ore (molybdenite) produced as a co-product or by-product of emerald mining in the region of Campo Formoso, BA, has arisen as the only economic option. The flotation process is commonly used in Brazil for the recovery of molybdenite from emerald mining tailings, but it produces low-content molybdenite concentrates, thereby resulting in a product with low economic value. The molybdenite concentrate produced in Campo Formoso contains 83.5% MoS2 (50% Mo), which is less than the international standard product that contains > 90% MoS2 (54% Mo).This low value is due to the presence of talc, which is a naturally hydrophobic mineral that is also floated with the molybdenite during the flotation process. Separability studies were done in a Partridge-Smith cell using dextrin and quebracho as a molybdenite depressor in solution at different concentrations and pH values to produce a technical-grade concentrate (i.e., 90% MoS2). These basic studies were accompanied by measurements of the zeta potential and contact angle, which was determined by the capillary rise method. The results of these floatability studies were used in bench flotation tests, which were performed in a Denver laboratory flotation cell. A molybdenite concentrate of 93.4% MoS2 was obtained when dextrin was used at a concentration of 100 g/t."

Jan 1, 2014

By Takashi Furuyama, Sukeyuki Mori, Takafumi Okuma, Norio Hashiguchi

The Tower mill KD-3 is an improved version of the laboratory mills VD-1, KD-1 and KD-2 in which the classifying column has been modified to ensure a quick discharge of products from the comminution section and, on the other hand, a better separation of coarse and fine particles; the latter being collected in a cyclone with a central spiral ribbon. To level the circling airflow through the classifying column and have a strict control over the maximum size of collected particles, a series of experiments was carried out, modifying the internal structure of the column: insertion of a vertical plate, a cone, or a horizontal net. The relationship established between the maximum size of products collected in the cyclone and the duct airflow rate indicates that, independently of the latter, the insertion of a cone in the classifying column could stabilize the maximum size of products collected in the cyclone around 15.1 - 17.5µm. With a horizontal net, the maximal size could be reduced to 8.4 - 11.3µm. This occurrence might result from the collision of coarse particles blown from the comminution zone with the base of the inserted materials and their settling down the bottom of the classifying column.

Jan 1, 2003

By Bisweswar Das, Barada Mishra, Hrushikesh Sahoo, Swagat Rath

Banded hematite jasper (BHJ) containing 45.2% Fe, 32.64% SiO2, 0.63 % Al2O3 and 1.25 % LOI is found difficult to beneficiate either by magnetic or flotation techniques due to fine intergrowth of jasper with hematite. Phase transformation by reduction roasting with activated charcoal followed by low intensity magnetic separation to achieve a suitable iron concentrate has been attempted in this study. The mineralogy of the ore and different roasted products has been studied by X-ray powder diffraction (XRD) and scanning electron microscope (SEM) to understand the reduction mechanism. The magnetite formation is observed at 850ºC while metallic iron appeared at a higher temperature. The effects of reduction variables such as reduction time (30-270 min), temperature (750-1050ºC), and reductant (1-12 %) using activated charcoal are studied. An iron concentrate with 64.65% Fe and 55.8% recovery could be obtained under optimum conditions of temperature: 850ºC, time: 1.5 h, and reductant: 6% by weight.

Jan 1, 2014

By Z. S. Abisheva

Rare and rare earth metals use quite often is an indicator of national economy development. The world structure of the rare-earth metals manufacturing countries in 2015 was presented as follows: China – 94.2%, India – 2.0%, Russia – 1.8%, the USA – 1.2%, Brazil – 0.5%, Malaysia – 0.3%. In Russia, large reserves of rare-earth metals, which reach nearly 28 million tons, are revealed. Kazakhstan, possessing a raw materials source of rare-earth metals, has all prerequisites for development of branch. Rare metals are manufactured in Kazakhstan incidentally by non-ferrous metals production. The production of indium, thallium, cadmium, selenium, tellurium, bismuth is made at the Ust-Kamenogorsk lead plant; tantalum, beryllium, niobium and molybdenum – at the enterprises of “National Atomic Company Kazatomprom” JSC. Production of a titanium, magnesium and vanadium is adjusted on “Ust-Kamenogorsk Titanium-magnesium Plant” JSC. Capacities for beryllic production yield are available on “Ulba Metallurgical Plant” JSC. The main producer of perrhenic production and osmium-187 is "Zhezkazganredmet" RSE. The single producer of gallium in Kazakhstan is “Aluminium of Kazakhstan” JSC; the capacity of enterprise is 25 t a year. In Kazakhstan innovative technologies for rare and rare earths mineral raw materials processing are created. The technology has been developed and a vacuum distillation apparatus has been created to purify crude selenium, which makes it possible to obtain a metal with a main component content of 99.9-99.99%. Technologies for processing of technogenic wastes and byproducts of the copper industry are developed. Implementation of technologies allow to obtain ammonium perrhenate, perrhenic acid, osmium isotope -187, tribasic lead sulphate, silver-concentrate. The technology of complex processing of black shales of Balasauskandyk deposit with the production of gold, vanadium, rare earth elements, uranium and ferrosilicon has been proposed. The processing was carried out using methods of autoclave leaching, sorption, extraction, precipitation. A highly profitable sorption technology for recovery of rhenium from solutions of underground leaching of uranium ores containing 0.2-0.4 mg/L of Re has been created. The organization of ammonium perrhenate production from solutions of uranium ore will significantly increase the volume of its production in Kazakhstan.

Jan 1, 2018

The relative abundance of coal in India compared to other fossil fuels makes it a natural choice as the primary source of fuel, be it for steel making, power generation or for other uses. The wide variations in nature and type of Indian coals formed during lower Gondawana period and categorized as difficult-to-wash due to its typical mineral matter association with the organic matrix call for suitable beneficiation techniques as the preferred option for quality upgradation. The good quality coking coals of the upper seams are fast depleting leaving behind the inferior quality lower seam coal. The lower seam coals presently being mined are mostly low volatile coking coal (LVC). They constitute about 50% of the total coking coal reserves in India. The beneficiation of Low Volatile Coking coals pose a major challenge and detailed R & D studies was taken up to study the beneficiation characteristics of these coals. The studies revealed that the liberation characteristics at coarser sizes are very poor and the coal is to be ground to finer sizes for liberation. The most important factor that determines coal cleaning efficiency is liberation of organic matter from mineral matter. To achieve liberation grinding is necessary as a result range amount of ultra fines (-0.063 mm) coal is generated. Presence of these large amount of ultrafine in the coal fines, often impose severe technical constraints affecting not only its floatability but also in the downstream treatment of the products like dewatering and cake formation particularly when it is beneficiating through froth flotation. In the present paper optimization of ultra fines (-0.063 mm) has been tried for a LVC coal of Jharia coal field for the better liberation and beneficiation of the above coal fines. It is observed that by optimized, combination of size and number of balls generation of fines can be controlled with liberation. Keywords: coking coal, liberation, floatability, dewatering

Sep 1, 2012

By Dianyin Liang, Hongxiang Ran, Xiaoming Wang, Xiaoou Xia

"This paper presents a new magnetic separator, which can be applied to increase the grade of fine magnetite ore feeding of ball mill. This innovative equipment possesses a rotating magnetic system and has a magnetic field of rapid polarity change which can strengthen the destruction of magnetic agglomerations and the dispersion of minerals to improve the quality of separation. Now this type separators have been successfully applied in several large concentrating plants such as Shuichang Iron Mine under Shouang Mining Company in China. Finally, this paper outlines practical results focused on feed grade and tailing yield, the results are showing that the quality of feeding can be improve tremendously. Hence, a new generator of rotating magnetic field has been paved. INTRODUCTION Jidong region in China is the important origin of iron ore, the characteristics of the iron ore in this region is low grade and complex, the iron mine discharges fine powder tailings reaches tens of millions of tons each year, in the wind action easy to form sand, this poses a threat to the atmosphere environment of Beijing. In order to reduce the mixing of large amount of useless ore and reduce the energy consumption of mill operation, a high efficiency pregrinding equipment is needed. Rotating magnetic field separator (RMS) is an advanced equipment, the main advantage of RMS is the significant reduction in particle entrapment and can easily break magnetic agglomeration. This reduction is so significant that RMS is capable of operating very close to theoritical limit for separator precision and can increace efficiency in selection process.Some expenrimental work on dry rotating magnetic field separation has been carried out in July 1998 in the company Ka Pty Ltd, then in 2008 BGRIMM developed industrial separation XCTG0816 in Shandong province . The wet RMS was researched in1960s in Former Soviet Union and the first industrial equipment was developed by BGRIMM in 1970s,then in 1990s wet RMS was applied in Ansteel group corporation. In 2017,6 units large wet RMS (SXCT1230)which were the largest RMS was applied in Sichuan province. No matter wet RMS and dry RMS, although they are used in differenct applications, they have some common research.in addition ,they all have good use effect."

Jan 1, 2018

By N. Pajunen

The basic objectives of current EU waste policy are to prevent waste and promote re-use, recycling and recovery to reduce negative environmental impact (2008/98/EC). In this paper, we focus on drivers and barriers for sustainable development by decreasing amount of waste and increasing material efficiency. Main target is to understand what are the most efficient drivers for environmental friendly decision making for reasonable consumption and use of raw materials. Environmental control instruments usually mean those actions the regulatory authority uses to control and limit environmentally harmful behavior of companies. A major change in the environmental control system took place in the 1980s with the focus moving from specific environmental issues to the environment as a whole. The environmental control system i.e. the legal (administrative), economic and informative instruments focuses on prevention. Before and still, the legislation is one of the main drivers in improving material efficiency. In this paper, we focus on drivers and barriers for effective industrial material use, and mainly on drivers. The objective of this study is to analyze how the drivers are working and are there any possibilities to influence on those. Our aim is also to introduce few examples of the existing supply chains and the drivers for better environmental performance and material efficiency. These examples are also compared with ideal reference scenarios. Our main research question in this article is: ?Are the financial issues the most important driver for environmental friendly strategic decisions?? In addition, retell the story from another perspective: ?The most important barrier for environmental friendly innovations seem to be the investment cost, the high risk involved in committing capital to unproven technology.? Other drivers, like the corporate social responsibility, stakeholder pressure, and general public pressure, will also affect the final decision. This article is based on research projects and literature. Keywords: drivers, decision-making, environmental management, saving primary raw material, material efficiency, sustainable production, critical raw materials

Sep 1, 2012

By Xiaoming Wang

This paper presents an arcuate magnetic separator to remove the grinding ball fragment directly from the mill discharge, which will cause wear to downstream processing equipment such as pump, hydro cyclones and pebble crusher. Furth more this type separator was applied in Wushan mine under China National Group Corporation in China. After months of operation, the equipment has been a success. It removes majority of ball fragments from mill discharge. Keywords: magnetic separator, sag mill, pebble crusher, grinding ball fragments

Sep 1, 2012

"The JKMRC researchers have been redeveloping the suite of breakage testing techniques to more realistically align with the breakage environment in comminution equipment. Computational modelling, especially with the DEM, has highlighted the modes of impact and contact, along with the energies of these interactions in a wide range of equipment. This has driven the need to match these modes in laboratory ore characterisation tests. The objective has been to build a continuum of breakage tests and associated models that span the required range of breakage forces and environments. The ore sample is subjected to a sequence of tests covering: abrasion (surface breakage) of angular through to smoothed particles; single particle impact from high energy single impact breakage down to low energy; incremental breakage covering 60 mm down to 50 µm particles; particle strength distribution; and bed breakage over a range of compression and energy input. These tests are suited to multi-component ores with a distribution of strengths. A modelling technique is also being developed to utilise primary breakage for modelling breakage under different types of confinement. This paper draws together these techniques, previously published by the authors, into a coherent whole. The suite of tests is approaching the point where a fixed set of tests can be used to model the performance of a full range of equipment, removing the need to conduct repeat ore characterisation tests for each different piece of equipment incorporated in a circuit design. This path should open up the application of different circuit configurations and novel equipment in comminution circuit design.1 INTRODUCTION Comminution modelling utilizes a wide range of ore characterisation techniques and methods to deal with the range of comminution equipment available for production use. In general, the tests have been designed to correlate with specific pieces of equipment, using calibration factors to provide the link between the small-scale test and industrial-scale performance. The majority of tests focus on estimating the power requirement of process equipment to achieve a desired throughput and grind size. Overall, this approach has achieved acceptable outcomes in the past, but the reality is that equipment sizing suffers from considerable uncertainty, in excess of ±20% is not uncommon. This uncertainty is covered by safety margins and automatic scaling factors in equipment selection. In striving to improve reliability, the industry tends to add more adjustment factors to the tests, and design margin rather than question the basic validity of the testing process. As the tests are often correlated to production equipment via carefully guarded databases, they are also locked into historic operating inefficiency, not providing direction or revealing opportunities to improve production efficiency in comminution equipment or circuits. Safe in the knowledge that they are achieving the expected production based on test work predictions, a site is unlikely to set their sights on reducing specific energy consumption by 10%."

Jan 1, 2018

By J. Langwaldt

Ammonium-nitrate is a main component in blasting agents and dissolved ammonium residues may be discharged with mine water. The European Union aims to reach a good state of the water quality and recommends ammonium content below 0.5 mg/L for drinking water. Natural zeolites adsorb ammonium from water. In this work, the removal of low-concentration ammonium by commercial natural zeolites was studied in continuous tests. Natural zeolites made up between 83% and 95% of the mineral composition. The major zeolite minerals were chabazite and clinoptiolites and minor amounts of erionite and mordenite were as well present. The five natural zeolite samples, 500~710 µm, were conditioned to obtain zeolites in the Na-form. Ammonium adsorption onto natural zeolites depends mainly on the zeolite mineral type. The chabazite containing zeolite was superior over the four clinoptiolite samples for the removal of low concentrations of ammonium from water (pH of 7.5, flow 5 mL/min, room temperature). The adsorption capacity of chabazite was 48.3 mg NH4+/g zeolites, i.e. 73% of the theoretical exchange capacity 69 mg NH4+/g, during duration over 107 days and almost 6700 bed volumes exchanged. The four tested clinoptiolites had an ad-sorption capacity of 15.7mg to 25.0 mg NH4+/g zeolites. The natural zeolites were rapidly regenerated by an alkaline sodium chloride solution fed to the columns.

Jan 1, 2014

By Arman Ehsani, Ersin Yazici, Haci Deveci

The downstream treatment of chloride leach solutions of WPCB for recovery of base and precious metals by a combination of adsorption and precipitation processes were carried out. A synthetic leach solution (1 M HCl, 116.5 g/L Cl-, 30 g/L Cu2+, 2.5 g/L Fe3+, 5 mg/L Au3+, 10 mg/L Ag+ and 20 mg/L Pd2+), which was prepared based on the composition of the pregnant leach solution obtained in the previous study was used in the tests. The leach solution was initially subjected to activated carbon (AC) adsorption (20 g/L AC, 80°C) in which gold was selectively recovered over silver and palladium i.e., 88% Au recovery at 0.5 h (92% at 3.5 h) compared with only 3-6% for Ag/Pd. Copper and iron were also observed to adsorb on AC as indicated by 1.4% and 17% decline, in their respective concentrations. Following the adsorption and filtration stage, metallic copper was added into the gold-barren solution to allow reduction of Cu2+ to Cu+, and to cement Pd on metallic copper. Over the mixing period (1 h), 93% of the Pd was recovered while only 1.4% of silver was cemented onto metallic copper. Subsequently, the leach solution was gradually neutralised by NaOH to pH 4, 7.5 and 9.5 for the precipitation of copper as cuprite (Cu2O). It was found that 41% and 46% of Cu and Ag, respectively, were precipitated at pH 4 at which iron was almost totally (99.8%) removed from solution. Precipitation of copper and silver was increased further at high pHs. At pH 9.5, cumulative recoveries for copper and silver were 91% and 85%, respectively. XRD analysis of the precipitates confirmed the presence of cupric copper oxides/hydroxides and revealed that copper losses occurred at pH 4 was due to the undesired presence of cupric copper in the solution.

Jan 1, 2014