Search Documents

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996

By David E. Albus, Bidjan Ghahreman

A single-family home constructed on the side of a slope in Los Angeles, CA, was subjected to lateral forces due to soil slope creep on the pile foundation supporting the home. Impacts to the property included cracking and separations in the street, retaining walls, exterior concrete flatwork, and decorative concrete features in the rear yard area. The home was supported by concrete piles that penetrated the surficial soil mantle and were embedded in underlying bedrock. However, the home exhibited minor distress that suggested even the home was being affected by soil creep. Selected points on the home were monitored with an optical survey method and manometer over a period of two years to assess if the home was undergoing vertical or lateral movement. Monitoring data indicated the home was in fact moving down slope in a manner consistent with slope creep. As a result, the authors were concerned that continued movement due to slope creep could result in over-stressing of the piles that support the home and ultimately lead to failure of the foundation system. An evaluation was then undertaken to evaluate the behavior of the foundation system due to forces from slope creep. Research was performed during the course of evaluating the conditions to consider various approaches to modeling pile behavior of the piles supporting the home. Some research has been performed to field measure creep displacement of soils and rock in slopes. These previous works have found a diverse behavior of the soil displacement with depth (velocity profile) indicating the process is very complex. An example of various velocity profiles measured in field experiments is depicted in Figure 1. Other research focused on theoretical models of velocity profiles and exhibited similarities to some of the field measured cases.

Jan 1, 2018

By John D. Nelson

Foundation underpinning is a common component of remediation schemes for distressed foundations on expansive soils. For many applications in expansive soil, micropiles have distinct advantages over other techniques. This paper will concentrate on the design and construction of micropiles in expansive soil. It discusses the nature of building distress and the relationship between foundation movement and soil heave. It presents methods for determining the factors that are required for the design of micropiles. Such factors include calculation of expected free-field heave, depth of soil wetting, and prediction of pier movement. A finite element program developed by the authors and others to determine pier heave and internal forces is presented. The input parameters that are required for pier analysis are discussed, and the nature of the output and the sensitivity of the results to the output are described. A case example illustrates the advantages of micropiles over other methods.

Aug 1, 2013

By Zhang Jiaju

For the highrise buildings with deep foundstion of irregular plane shape, an appropriate calculate model to the heave of foundation soil after excavation is proposed and studied using analytic method and FEM (Finite Element Method) respectively to provide an effective way for solving this kind engineering problem. Also combined with the practice of construction deep foundation of Capital Mansion, calculation of the heave of foundation soil after excavation is given. Compared these results from above two methods with the results measured in situ, it is conformal on the whole, and the results by FEM are much closer with the measured.

Jan 1, 1991

By Jean J. Abiassi

The Boston Marine Industrial Park (BMIP) VENT 6 project is a cut and cover tunnel, part of the Central Artery / Tunnel (CA/T) in the city of Boston. The BMIP job will serve as the south approach to the Third Harbor Tunnel crossing. The alignment is approximately 2500 Ft long and is made up of four sections starting from west to east: 1. West Tunnel 2. Boat Section 3. East Tunnel 4. Tunnel inside Vent 6 Cofferdam and connection to the Third Harbor Tunnel. The support of excavation (SOE) system for the West Tunnel, Boat Section, and East Tunnel are all a part of this project whereas the SOE for Tunnel inside the Vent 6 Cofferdam was a part of the contract for the Third Harbor Tunnel.

Jan 1, 1994

By Derrick Dasenbrock

Two DFI committees independently organized two complimentary panel sessions for the recent American Society of Civil Engineers' (ASCE) Geo- Risk 2023 "Advances in Theory and Innovation in Practice" Conference in Arlington, Virginia, July 23-26. The Geo- Institute (GI) specialty conference welcomed more than 200 professionals and students interested in risk from around the world to the Washington, D.C., area for three full days of plenary keynote lectures, papers and no-paper sessions. The GI Risk Assessment and Management Technical Committee organized the event, which is the third in a series planned on a 6-year cycle. The previous two events were in 2011 in Atlanta and 2017 in Denver.

Sep 1, 2023

By David A. Staab

Numerical modeling was used to investigate the feasibility of using two geophysical imaging techniques, cross-borehole ground penetrating radar (XBGPR) tomography and electrical resistivity (ER) tomography, for detecting and characterizing defects in deep-mixed soil columns. XBGPR modeling was accomplished with a three-dimensional numerical forward modeling code and a two-dimensional inversion routine. Spatial variations in apparent dielectric constant (Ka) and attenuation (a) were mapped. Electrical resistivity modeling was accomplished with a three-dimensional numerical forward modeling code and a three-dimensional inversion routine. Spatial changes in electrical resistivity were then mapped. Three different types of defects were simulated, in addition to a defect-free column. The computer simulations suggest that XBGPR tomography and ER tomography might be useful, non-destructive methods for detecting and estimating the extent of defects in deep-mixed soil columns. The results show that small, isolated defects might be difficult to detect, but defects approximately equal to or larger than the sampling interval (for XBGPR) or vertical electrode spacing (for ERT) should be detectable.

Jan 1, 2004

By Vasileios A. Drosos

The response of pile foundations to lateral loads is an important factor for the successful performance of several critical structures. A new numerical code for the analysis of single piles under lateral load is outlined. The code can simulate (through appropriately chosen parameter values) not only the non-linear behavior of soil, but also the inelastic structural response of the pile itself under lateral load. Emphasis is given on the calibration of model parameters and the verification of the code. For the calibration of the parameters, data is used (a) from the well documented in the literature p-y curves, and (b) from experiments conducted either in full scale or in the centrifuge. Results are compared to those of well known published codes for inelastic analysis of single piles under lateral load.

Jan 1, 2006

By Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments on soft soils was introduced some 20 years ago and is now considered State-of-the-art worldwide.The GECs consist of compacted granular fill, similar to common gravel columns, with one decisive difference: they are confined in a high-strength low-strain flexible geotextile “cylinder” (encasement). This engineered element provides a very efficient tool to control and optimize the behavior of the system. GECs perform very well even in extremely soft soils ensuring bearing capacity (stability) and reducing settlements. Due to the encasement, they a lso provide high lateral ductility. A wide range of fills including sands can be used.The remarkable reduction of vertical stresses in the soft soil surrounding the GECs results in a decrease of lateral pressure as well. Such reduction combined with the lateral ductility allow GECs to be also used for lateral pressure-relief adjacent to sensitive foundations, e.g. rigid piles. The application of GECs as lateral pressure relief was recently used in Brazil and Germany where bridge abutments were built on concrete reinforced-piles. The GECs below the bridge approaches and adjacent to the piles decreased the lateral pressure to acceptable values.This paper presents two case studies for which the most relevant parameters, the geotechnical conditions, specific problems, engineering philosophy, final solution and lessons learned are discussed. Furthermore, instrumentation programs were applied in both projects. The most important results in terms of displacements and stresses are shown, evaluated, summarized and commented upon, focusing on the lateral stress-relief, followed by conclusions and recommendations."

Jan 1, 2016

By Paul J. Axtell

Two new railroad bridges in Kansas City, Missouri are founded on drilled shafts embedded into the soil and underlying shale. The uncertainty arising from the non-homogeneous, anisotropic nature of most shales, and the variability of shales across the U.S., makes it a difficult material to assign appropriate design properties. As was the case on this project, the uncertainty of foundation performance in shale can lead to overly conservative designs, particularly with drilled shaft foundations. An extensive Statnamic axial testing program was performed to verify that the load-settlement behavior of the drilled shafts would be acceptable for the intended railroad traffic. Axial Statnamic testing was applied in three increasing cycles of 927 kips, 1007 kips, and 3177 kips, respectively. The maximum movements recorded at the shaft head during each of the loadings were 0.052 inches, 0.062 inches, and 0.257 inches, respectively. The loads applied in each of the respective Statnamic tests were not sufficient to reach the capacity of the shaft; so direct comparison of measured and calculated capacities is not possible. However, evaluation of the estimated design capacity can be accomplished based on results from the Statnamic testing program by utilizing normalized load transfer relations presented by O?Neill and Reese (1999). Such comparisons necessarily require extrapolation of the data measured in the Statnamic tests following typical load-displacement response. Results indicate the Kulhawy and Phoon (1993) method for estimating side resistance in Pleasanton shale rock sockets, assuming a smooth socket, appears to agree well with observed behavior during Statnamic testing. Accordingly, the O?Neill and Reese (1999) method for estimating the toe resistance in intermediate geomaterials, assuming cohesive rock with Rock Quality Designation (RQD) between 70 and 100, appears to agree well with observed behavior during Statnamic testing. Finally, based on Statnamic testing at varying load magnitudes and normalized curves developed by O?Neill and Reese (1999), the contribution of side resistance to the capacity of a deep foundation can be determined assuming no load is transferred to the base of the foundation during lower magnitude testing. Furthermore, higher magnitude testing can provide a means to evaluate the accuracy of design end bearing calculations.

Jan 1, 2006

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989

By Howard A. Perko, Melinda J. Hummel

"Hydraulically jacked piles, herein referred to as jacked piles, are commonly used for underpinning existing structures to arrest settlement or augment an existing foundation for higher loads. They consist of steel pipe segments coupled together and jacked into the ground using a hydraulic ram. Pipe sections can vary in size from 3"" diameter to 18"" diameter or larger. Jacking resistance is typically provided by dead loads of existing structures. This type of piling system has been utilized for foundation underpinning, repair, and augmentation for more than 120 years, yet little has been published on the capacity, installation standards, and reliability of these systems. Pile load tests from a number of projects are presented and analysed. The data show that previous methods of jacked pile capacity and depth prediction are crude at best. Empirical relationships between capacity, depth, soil type, and standard penetration resistance blow count contain a high degree of scatter. Scatter in the data indicate capacity prediction for jacked piles needs further research and refinement.INTRODUCTIONPush pier, resistance pile, steel pier, and jacked pile are some of the names often applied to hydraulically jacked piles used for underpinning. The term ‘jacked pile’ is more common in building codes and will be used herein. Although jacked piles can be installed for new construction, this paper is focused on piles used for support of existing structures.Jacked piles consist of short segments of pipe or structural steel tube that are coupled together and forced into the ground using a hydraulic ram fastened to or beneath a footing, stem wall, or grade beam of an existing structure. In this way, the weight of the structure provides the resistance necessary to force the pile into the ground. A factor of safety can be achieved in design by redundancy, which is consecutively installing more than one jacked pile to support the same portion of foundation. Installing jacked piles consecutively using the same dead load and then releasing the load after each pile installation allows one to continue adding piles to the same general area until a total aggregate capacity is achieved to account for anticipated dead plus live loads and a desired factor of safety for that area.An engineering schematic of an example jacked pile connected to a footing foundation is shown in Figure 1. Modern jacked piles typically incorporate a steel bracket. There are many sizes and styles of brackets available. Some categories include plate brackets that bolt to the outside of an existing foundation wall, wide and narrow angle brackets that extend under existing footings, pin brackets for attachment to structural steel, and reverse angle brackets for attachment to footing and wall. Table 1 lists example brackets and their benefits."

Jan 1, 2017

By Cheng Lin

The Group Equivalent Pile (GEP) approach was proposed by researchers to analyze a laterally loaded pile group. This approach enables engineers to evaluate the behavior of a pile group in single pile analysis software, such as LPILE. A previous study showed that the calculated results using the GEP approach for piles agreed well with field test data. To evaluate the accuracy of the GEP method for analyzing laterally loaded shafts, two case studies with different shaft diameters were performed in this study. The comparisons showed that the calculated results using the GEP method and considering the contribution of the shaft cap if embedded generally agreed with the measured from the full-scale tests.

Jan 1, 2009

By James Green

It has often been said that the best contracts written are by people who are suspicious of each other. The Spanish philosopher, Ortega y Gasset, said: "Every contract is an Act of Distrust." The arena for dispute settlement outside of the courts is increasing day by day - contracts, especially construction and civil engineering contracts, are written containing arbitration clauses for settling disputes - the very drafting of standard forms of contract, do in some instances by their very construction, create an ambiguity as to intent and provide a breeding ground for dispute. I come from a land far across the sea - the most southern land before the South Pole. Being a young country, 150 years old, we are still progressing - being far removed from the trouble free zones of the world and nuclear free we enjoy a lifestyle second to none.

Jan 1, 1987

By Cory J. E. Yacyshyn

Anchored steel pipe piles are being used more frequently in British Columbia for shoreline projects such as public ferries, cruise ship docks, containership terminals and locally in the expansion of the Vancouver waterfront convention center. While a 36? diameter driven pile may provide adequate compression loads it will not always achieve enough penetration to provide the required tension loading. That is why bundles of threaded anchors or strands are drilled through the center, past the pile tip, and anchored into the underlying strata. Drilling up to 250 feet deep through the piles in variable water bearing strata presents challenges. Southwest Contacting Ltd. (SWC) recently completed the three largest anchored pile projects in BC; Vancouver Port and Convention Center Expansion, Vanterm Container Terminal and the new Prince Rupert Cruise Ship Terminal. This paper will present the separate challenges encountered drilling the anchors. At Prince Rupert, the recently completed Northland Cruise Ship Dock ultimately required a cased system to drill and install triple thread bar anchors. When 200 foot long steel pipe piling was unable to penetrate the highly fractured gneiss/schist bedrock to obtain a seal and consolidation grouting was unsuccessful, a modified cased system was advanced deep enough into the rock to eventually seal. The 3-#20 bars were changed to 12-strands since the bars wouldn?t fit through the smaller cased hole. The options were limited because each dolphin only had enough room for a small hydraulic drill rig that wouldn?t have the power to fully case the holes. The Canada Place Pier Extension in Vancouver?s Harbor led to the development of an innovative tip design used later at Vanterm. The 36? diameter steel pipe piles were driven closed end but modified to permit drilling through a concrete plug at the base. The driving of the piles at Canada Place often knocked out the plug so we were faced with 50 feet of sand up inside the pile when the drilling started. This led to discussions on how to safely remove the sand, solidify the tip, and continue drilling to get past the tip without undermining the pile. Finally, Vanterm Berth Extension was completed with a unique drilling system because the pile tips stopped in hydraulic sands, as opposed to the native till. We were faced with advancing the casing to the till without undermining the base of the pile. With 100 psi water pressure at the pile base after we broke through the concrete plug, the trick was to prevent charging the sand with our 250 psi air which liquefies it and forced it up our drill casing. And of course, it has to happen just before Christmas holidays!

Jan 1, 2004

By Arash Khosravifar

The seismic design of extended pile shafts for the combined effects of dynamic shaking and liquefaction-induced lateral spreading is investigated using nonlinear dynamic finite element analyses (NDA). Results of NDA parameter studies are used to illustrate how inertia and lateral spreading loads combine during shaking. The NDA results are used to evaluate equivalent static analysis (ESA) methods. Implications for design practice are discussed.

Jan 1, 2010

By George K. Burke

Single axis soil mixing is a mechanical method of blending soil in situ with a reagent binder to achieve improved character. Generally this achieves a design compressive strength or shear strength and/or permeability, but can be used to immobilize and/or fixate contaminants as well as a treatment system for chemical reduction to a more "friendly" substrate. The reagent binder can be a variety of materials, including cement, fly ash, slag, lime, and an assortment of additives. Usually this reagent is delivered in a slurry form (combined with water), but the Dry Mix Method uses pneumatic conveyance.

Jan 1, 2001

By Eric C. Halpin

"1. Introduction and Backgrounda. In its fundamental form, risk is simply the likelihood of an adverse impact. Expanding on this theme, the Corps of Engineers has broadly defined risk associated with infrastructure as a factor of three distinct elements: a probabilistic assessment of a hazard such as a flood or earthquake; a probabilistic assessment of how the infrastructure performs in the face of this hazard; and a measure of the likely consequences – loss of life, economic damage, environmental impacts – associated with the resulting inundation scenarios.b. The lessons and observations described herein relate to the Corps of Engineers experiences in implementing risk concepts for infrastructure management during the period 2005 through 2013. The Corps of Engineers is a large, decentrally operated and centrally led federal agency that plans, designs, constructs, operates, maintains, and/or manages a portfolio of over 3,000 built dam and levee systems within the United States. The infrastructure in this portfolio is 55 years old on average, and although much of the structures provide for flood risk management benefits, many of the dams deliver multi-purpose benefits. Scale matters – where scale and uncertainty are large, risk concepts provide great opportunity and arrangement for application.c. The amount of organizational change that is demanded for the implementation of risk concepts is considerable and should not be under estimated, but need not be feared if the path others have taken is considered. This paper is, in many ways, an opportunity to step back from the last seven years of implementing risk informed management, check our own azimuth and maturation, and share the purpose and energy behind our own continuing actions. Hopefully, this azimuth check is also beneficial to those that are either considering the use of risk or are in the process of implementing risk concepts.d. Success at managing the massive change related to incorporation of risk concepts will directly affect success of the infrastructure program. The three key organizational elements to consider –human systems such as governance and competencies; policies that outline the who, when, and why of decisions and management; and the processes and technology that outline how work is to be performed - are changed fundamentally. From senior leaders to project team members and all of the people in between, there is a need to discuss, confront, and vet the change and the role people and organizations have in the process. For the Corps of Engineers, with a history of over two centuries, deeply embedded beliefs about infrastructure aren’t transformed over night - the change process is decadal in scope. Given our self imposed “project execution” mantra and corporate objective, risk seemed threatening at first to the cost and schedule of delivering infrastructure projects. In reality, risk concepts have been responsible for savings and cost avoidance of nearly $6 billion over the last three years alone while at the same time justifying increased investment by several fold for the highest risk needs."

Jan 1, 2014

By Pan Shisheng

Amodified load transfer method computing the displacement, axial compression, skin resistance, toe resistance, and other static bearing behaviours of piles, is propoesd in this paper. Through deriving a new concrete computational method with simple integration, many complex factors, such as different soil properties of each layer in layered soil, variation of soil parameters with the changes of the depth, different elastic moduli of piles under different loads, and even different areas in the same pile, can all be easily considered. This method fits in with many types of piles, including friction and point bearing piles, precast and cast-in-situ piles. Observation of static loading test on pile is given, and the computed values from the modified load transfer method are found to agree with practical measured results.

Jan 1, 1991