Search Documents

By Peter Wells, Adrian Sabau, Turgut Yalcin

"The nickel ores of Sudbury contain substantial amounts of the gangue mineral pyrrhotite (Fe7S&) which causes certain diflculties in the milling of these ores. This paper proposes a process called “magnetoflotation” as an effective means of dealing with pyrrhotite. The method reduces the pyrrhotite content of concentrates by applying a magneticjield on the path product as it leaves the flotation cell.Successful performance of magnetoflotation requires the optimization of several variables. In this study, three of the variables (air flowrate, collector concentration, pother concentration) were investigated by Box- Wilson experimental design, and others (magnet speed, grind size, pulp density, flotation time) were examined individually. The process was tested on a Falconbridge nickel ore, assaying 1.92% Ni, and under the best operating conditions, a concentrate was obtained with 13.56% Ni grade and 74.32% recovery in a single step. Further improvements to grade and recovery were possible by cleaning and scavenging. The same ore was also tested with conventional methods for comparison, and results indicated that magnetoflotation performed better.INTRODUCTION“Magnetoflotation” refers to the process of carrying out magnetic separation and flotation simultaneously within the same device, and is intended to prevent magnetic minerals from reporting to the froth products while non-magnetic minerals are being floated. Typical cases where this method might be beneficial include the processing of magnetite and nickel ores. Its use on magnetite ores has been reported elsewhere [Yalcin, 1992; Yalcin, 19931. This paper describes its application to nickel ores, more specifically to the nickel ore of Falconbridge Limited in Sudbury."

Jan 1, 1999

By Seppo Haapamaki

"Since it started production in 1970, Anderson Lake Mine has experienced several radical changes in mining methods as a result of the physical characteristics of the ore zone along with the need for improved productivity. This paper examines the transition from longhole open stoping to mechanized cut-and fill then to vertical crater retreat at Anderson Lake Mine. The reasons for the need to change mining methods is analyzed taking into consideration the impact of such criteria as improved productivity and ground conditions and how these criteria affected the over-all economic viability of the mine. IntroductionAnderson Lake Mine is one of five producing copper mines in the Snow Lake area and is situated approximately 3 km southeast of the townsite of Snow Lake (Fig. I).The mine production rate at Anderson Lake is 700 tpd and all ore is trucked from the mine to the mill located approximately 2.5 km from the mine site . The mine is serviced by a three-compartment shaft sunk to a depth of 3300 ft with level spacings at 175 ft and 150 ft intervals from the 600 ft level to the 3000 ft level. .The shaft was collared in 1965 and, a year later, the hoist and compressors were installed. By 1969, a crusher system had been built and actual production began in 1970. During 1978, production was suspended for the year to allow for 430 ft of shaft deepening."

Jan 1, 1988

By Jacob Masliyah, Zhiang Zhou, Dharamdat Christendat, Tshitende Kasongo, Kevin Hyland, Zhenghe Xu, Ted Kizior, Douglas Cox

"A novel on-line visualization system, previously developed at Syncrude Canada Ltd., has been modified to characterize rising bubbles, particles and particle-bubble aggregates in a flotation process. With this system, the bubble size and rise velocity in a laboratory flotation cell can be determined. The technique allows the loading of solids on bubbles to be visualized, thereby providing an in-depth understanding of sub-processes of flotation. A step-by-step data processing procedure is presented. The applicability of the developed system to mineral flotation and bitumen extraction is discussed. Under batch flotation conditions in a laboratory Denver cell, three main bubble-particle attachment patterns are observed. They are: i) single particles attached to single bubbles, ii) particle aggregates loaded on single bubbles; and iii) a group of particles aggregated with a group of bubbles. The results demonstrate that the on-line visualization system is a powerful tool for understanding and diagnosing flotation processes.INTRODUCTIONAir (Gas) bubbles are an indispensable component in a flotation system. Both industrial practice and theoretical analysis indicate (Yoon, 1993; Diaz-penafiel and Dobby, 1994) that the size and population of bubbles are two important process parameters in modeling flotation. More recent investigations (Finch, et al., 1999; Gorain, et al., 1997) suggest that for a given flotation system, bubble surface area flux, defined as the air liquid interfacial area per unit time and unit cross-sectional area of flotation cell, showed a better correlation with the flotation rate constant. As a result, the bubble surface area flux is now being considered as a key parameter to account for the combined effect of bubble size and population in evaluating the performance of flotation machines and modeling flotation processes. However, the success of using bubble surface area flux in flotation process modeling largely depends on how accurate it can be determined or estimated (Finch, et al., 1999)."

Jan 1, 2000

By M. W. Bartley

DURING the field season of 1938, the Ontario Department of Mines assigned a combined geological and geophysical survey patty to the investigation of the location, genesis, structural relationships, and economic possibilities of the hematite deposits at Steeprock lake. The investigation was carried out by detailed mapping of the rock exposures and a magneto-metric survey of the drift-covered portions of the area. This was supplemented during the winter of 1938-39 by further geophysical work conducted on the ice. Dr. A. A. Brant, of the Department of Physics, University of Toronto, was in charge of the geophysical work for the Department of Mines in the summer and for the Sterola Exploration Company in the winter. The writer supervised the geological examination. Scope of the Paper The present paper is an attempt to acquaint the members of the Institute with the structure and mode of occurrence of the deposits, since many people are of the erroneous opinion that they are analogous to the Mesaba and Michigan deposits. It is hoped that, from this discussion, they may be able to draw some conclusions of their own regarding the nature of the deposits, and the importance and future possibilities of the region.

Jan 1, 1939

By K. Gie Tan, Frank Wright

"Misty Mountain Gold Limited (MGL - TSE VSE, MGLCF - NASDAQ) of Vancouver, owns the Harmony Gold Project located in the Queen Charlotte Islands of British Columbia. The deposit contains a mineable reserve of 2.3 million ounces of gold, at a 1.2 g/t cut-off and an average grade of 2.1 1 g/t Au.Discovered in 1970 and frequently investigated by previous owners, full-scale production has not yet occurred because of the complex metallurgy of the deposit. Recent process studies that were completed in six months at Process Research Associates Ltd. (PRA) of Vancouver resulted in significant improvements to the project viability. The work involved detailed mineral processing studies aimed at achieving a marketable concentrate. An option for bio-oxidation and cyanidation to allow on-site dor6 production was also investigated.The main findings at PRA followed the front-end recovery of finely divided free gold (Au) by gravity concentration. Approximately 20% of Au reported to less than 0.2% of the mass, resulting in a grade exceeding 500g/t Au. The resulting gravity tailing provided a uniform feed for flotation evaluation. The optimization of this step allowed for a reasonable primary grind size of 80% passing (&) 50pm. Efficient slime’s rejection was made possible by flotation at a reduced pulp density, and pre-oxidized sulphides were reactivated with Na,S. The regrinding of the bulk flotation concentrate followed by up to five stages of cleaning resulted in a combined gravity + flotation product of 50g/t Au with 82% recovery in less than 4% of the feed mass.Further studies indicated that the flotation concentrate was amenable also to tank bio-oxidation. At 65% sulphide oxidation the gold recovery improved from less than 70% to 90% by cyanide extraction using CIL (carbon in leach). This compares to less than 45% gold recovery from whole-ore cyanidation in several previous studies. Heap leaching may also be considered for lower grade material. PRA’s methodical approach and consistent results dispelled the uncertainty about predicting the material behavior for the Harmony Property."

Jan 1, 2000

By Murray Wood, Michael Schaffer, Makat Katom

"An expert system applied to the control of mineral process unit operations is, by its nature, the site best operating practice, having been designed by the local experts in conjunction with consulting metallurgists. The “common sense” layer in a MET (MinnovEX Expert Technology) solution determines an appropriate action for the current operating conditions through a developed heuristic model of the process (expert system). The magnitude of the setpoint change that is made is proportional to the confidence that the system has in its interpretation of the current conditions (fuzzy logic). The solution is always striving to take the process to a constraint and thereby optimise the operation. An accepted limitation of the solution is that the only way the system can determine if a constraint has been reached is to exceed it and then withdraw – essentially “experimenting” with the process. By leveraging a model, which can accurately ""simulate"" the process, this restriction can be circumvented by pre-testing the set point change through a ""what if"" analysis and then modifying the solution as appropriate.At Ok Tedi, the introduction in 1999 of a MET expert system for SAG milling resulted in significant improvement in circuit throughput. Yet, with the additional inclusion of an accurate model of the process there was still more that could be achieved. Hence, in 2002 a MET Neural Network model was developed and deployed to enhance the existing expert system solution. The principal objective of this model was predicting the effect that changes in SAG tonnage and density would have on the power draw of the mill - essentially a power predictor. The results have seen a decrease in process variance with an associated increase in average circuit performance.This paper describes the methodology by which the Neural Network model was implemented, the considerations and limitations when applying this technology and ultimately the results that were achieved."

Jan 1, 2003

By L. Betteridge, A. Marks

"An OK 300 cu. ft. Skim - Air cell was installed at the HBM&S concentrator in Flin Flon in 1987. Since that time, 3 additional OK Skim - Air cells have been installed in HBM&S concentrators. The cell treats a coarse 70% solids slurry with a residence time of 2.5 minutes. The product from the cell (a unit cell type application) is a final grade copper concentrate with high precious metal values. Since its installation, the cell has improved gold recovery by 10 - 15%. Process variables such as circulating load, pH, froth depth, feed size, and reagent additions all have an effect on the operation of the cell. Maintenance on the cell has been minimal. Initial operating problems involving level control have been significantly reduced and operations are now relatively trouble free. Although very successful at Flin Flon, site specific operating circumstances will determine the suitability of this cell. INTRODUCTIONHudson Bay Mining and Smelting operates four concentrators in Northern Manitoba. Three treat copper-zinc ores, the fourth mills a copper-nickel ore. The Flin Flan concentrator operates two circuits in parallel which treat copper and zinc ores from the Trout Lake and Callinan mines. Both circuits in the Flin Flan mill have Skim-Air cells integrated into the grinding circuits.The Trout Lake cell was installed first and had a payback period of a few months. Required modifications to the cell were made to enhance its performance. These included changing the discharge valve size, tuning the level controller, and installing an insert into the rubber valve sleeve to increase its wear life. The payback period on the Callinan cell was significantly reduced because these modifications were completed prior to its installation.The cells produce a final grade copper concentrate and since their installation gold and silver recoveries to the final copper concentrate have increased significantly. Operating parameters such as coarseness of cell feed dictate the metal recoveries and froth depth determines the selectivity of the cell and therefore the grade of the concentrate.The Skim-Air cell can be suitable in applications where a final product is generated. However, when a bulk concentrate, which requires further separation, is produced, the coarseness of the product may not make it amenable to conventional flotation.The Flin Flan mills Skim-Air cells have worked exceptionally well with little maintenance required."

Jan 1, 1991

"The Key Lake mill was commissioned in 1983 to process the two Key Lake ore deposits. With the depletion of these ore bodies in 1999, the plant was converted to mill the exceptionally rich McArthur River deposit located seventy eight kilometers northeast of the Key Lake mine site. This paper describes in detail the Key Lake milling process. The mill consists of a grinding circuit, a leachkounter current decantation circuit, a solvent extraction circuit, a yellowcake precipitatiodcalciner circuit, an ammonium sulphate crystallization circuit, and a waste treatment circuit. The paper also describes process changes to handle McArthur River ore, including the ore receiving stationLOCATIONThe Key Lake mill is located 78 kilometres south of the McArthur River mine. It is located at latitude 57' N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pine House, located 240 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYAND DESCRIPTION OF OPERATIONThe Key Lake mill was commissioned in October 1983 to process ore from the Gaertner and Deilmann ore bodies. The mill was designed to produce twelve million pounds of uranium oxide (U308) a year from a feed grade of 2.4% U3O8.Following grinding, the uranium is leached in a two stage leach circuit using oxygen and sulphuric acid. An eight-thickener counter current decantation (CCD) circuit is used to separate the uranium bearing solution from the solid waste residue. The uranium is further purified in a solvent extraction circuit and then precipitated using ammonia. It is then calcined at 840' Celsius, and packaged into drums for shipping to refineries. There is a crystallization circuit to recover ammonium sulphate produced in the process and a waste treatment circuit."

Jan 1, 2001

By C. O. Aksoy, H. Kose, K. Heasley, E. Yalçin

"In Turkey, the growing demand for lignite has resulted in increased lignite production and an emphasis on improving underground recovery. This has resulted in a gradual increase in the application of the retreat longwall mining method and also in the extraction of the safety pillars protecting permanent underground structures (drifts, shafts) in mines prior to their abandonment.Extracting these safety pillars presents a special hazard to mine employees and the stability of the mine. Often subjected to high stresses, the behaviour of these pillars is not always predictable. Special care must be taken to ensure that infrastructure does not collapse prematurely, and that working conditions remain safe. Otherwise the extraction must be halted, and the remaining coal lost.This investigation reports on a study of the stability of safety pillars during the final extraction phase of the Hustas mine in Soma, Turkey.” The model construction was based on mine plans, and material properties were derived from physical properties testing. Observed subsidence effects from other mining events were used to calibrate the overburden lamination thickness.The model results compared well with surface physical disturbance occurring as a result of mining, as well as with conventional longwall stress redistribution theory and underground observations. The study has shown that properly calibrated models can be useful in assessing mine safety during remnant pillar extraction. The LAMODEL results demonstrate the convenience of this easy to use software."

Jan 1, 2004

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By Leslie F. Sawatsky

Each potential oil sands developer deals with the question of optional sources of raw water to supply large water demands that range from 50 to 80 million cubic metres per year for each of six existing and planned developments. The Athabasca River currently supplies nearly all of the water to the existing mines via conventional bank intakes, which has resulted in some concern over the effects of reduced river flows. This paper describes the various water supply options, and the likely scenario for future oil sands water supply projects. Various water supply options have been suggested including Athabasca River water via infiltration galleries, groundwater, combined Athabasca River water and alluvial groundwater using wells (i.e. bank filtration systems), diversion of tributary rivers, utilization of large lakes in the region and pumping from other large rivers in the region. Investigations show that the size of river catchment needed to support raw water usage by a typical oil sands mines exceeds 5,000 km2 eliminating all tributary rivers that are located in the oil sands region except those rivers with large drainage areas like Firebag and MacKay Rivers. Lakes cannot be used as a source of supply due to large water deficits for smaller lakes and the large cost of sourcing water from a lake as large as Lake Athabasca. A groundwater source alone would not likely meet the large water demands. River intakes on the Athabasca River will likely continue to be the most practical water supply option for oil sands mines north of Fort McMurray, although various types of Athabasca River intakes are possible. Existing intake systems include screened riverbank intakes, forebay intakes, and river bottom intakes. Infiltration galleries are not feasible for most sites, though some bank-filtration-type systems using high capacity wells may be an option if there is sufficient thickness of high-permeability alluvium at a suitable location in the Athabasca River valley.

May 1, 2004

By Sibabrata Patnayak

A major problem during shovel excavation in oil sand mining is the variability of material diggability resulting in varying mechanical energy input, cycle time, energy consumption, wear, and stress loading of shovel dipper-andtooth assembly. This variability greatly influences the mining equipment performance. Different approaches such as empirical ground classification systems, analytical methods, and performance monitoring that are used to determine diggability of groundmass are reviewed. It is concluded that the existing empirical diggability classification systems are site specific and mostly based on rock and therefore, cannot be used for shovel excavation in oil sands. The O&K wedge test is a simple and useful index test for establishing correlations between cutting resistance and geotechnical properties of coal and other soft rock overburden material. But this test, when performed on small size unconfined oil sand samples, may not give reliable indication of diggability because of the boundary conditions on the specimens. Digging predictions made using analytical and laboratory digging models need to be verified with performance monitoring data to better understand the digging effort in oil sands.

Apr 1, 2005

By A. C. Wilson

In 1991, local prospector C. ?Mickey? Clement recovered at least three alluvial diamonds from the Michipicoten River. Two of these stones were sent to the Department of Mineralogy, Royal Ontario Museum, where they were identified as industrial grade diamonds with weights of 1.05 and 1.13 carats. Both stones were described as frosted and graphite-inclusion riddled. In 1995, prospector Sandor Surmacz and geologist Marcelle Hauseux discovered diamonds in bedrock approximately 20 km north of the Michipicoten River. An 18.1-kg bulk sample of a xenolith-rich lamprophyre, taken from an outcrop at the side of the Trans Canada Highway north of Wawa, yielded 1 macro diamond and 5 micro diamonds. All but one was gem quality (Sage 2000). Since then, more than 36 occurrences of diamonds in bedrock have been reported in an approximately 30 km2 area centred 20 km north of the town of Wawa. The occurrences are hosted within a sequence of unusual, Archean-aged, heterolithic breccias previously considered to have no economic significance. Ten kimberlite occurrences also have been confirmed in the Michipicoten greenstone belt in the last 5 years. Two of these kimberlites are diamondiferous. To date, expenditures on property acquisition and diamond exploration in the Wawa are estimated at $120 million (CAN). This paper summarizes the geological observations made on these occurrences and discusses including the relationship between the occurrences and the regional geology.

May 1, 2003

By S. E. Daniel

"Due diligence reviews are an essential part of mineral property acquisitions. One of the primary reasons to complete an environmental review prior to exploration property acquisition is to assess the potential environmental liability. It is critical to identify the potential reclamation costs or existing environmental liability associated with the exploration property. A review of the existing condition of the property and its history can allow prioritization of exploration targets and ease future expenditures for historic damages. IntroductionIn Canada and some other jurisdictions, the purchaser of a property is assumed to know, and is (in the absence of deceit or fraud) financially responsible for, what is purchased. A plea of ignorance, at least from the perspective of environmental liability, is not an acceptable excuse to avoid responsibility (Nelson, 1994). Therefore, if an exploration company (for the purposes of this paper, any organization conducting exploration work) purchases a property that has environmental contamination, the new owner is liable for the cost to reclaim the site to an acceptable level. The cost to reclaim the site is the environmental liability. The new owner is responsible for existing environmental liability of the property, even if the exploration company’s personnel were not aware of the problem. In simplest terms, buyers beware. Therefore, in order to protect the exploration company’s interests, the exploration manager should determine the characteristics of the property of interest prior to purchase or other involvement, and exercise due diligence.The term “due diligence” is often used in the mining industry. To ensure clarity, in this paper’s context, the author has chosen to use the following meaning: “… due diligence is used to describe a detailed data review, generally in connection with the purchase or sale of a mineral property, the approval of a large capital expenditure, or the borrowing of a large sum of money” (Smith, 1997).Directors of the exploration company are held liable for the decisions made, unless they have relied in good faith on,“…a written report of the auditor, or a report of a lawyer, accountant, engineer, appraiser, or other person whose profession lends credibility to a statement made by any such person” (OBCA, 1994)."

Jan 1, 2003

By W. J. Dick, K. G. Kress

A pipeline syphon can be a simple and reliable alternative for water conveyance as compared to otherwise more complex pumping systems or low-level outlet conduits through earthfill dams. In a simple form, it consists of a pipeline constructed over the top of a dam or other high topographic feature, connecting a source pond to a receiving pond or channel (Fig. 1). The syphon action is initiated by removing air from the pipeline (priming) using water pumps, vacuum trucks, or simple devices that can be purchased “off-the-shelf.” Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate, or other devices. Repriming is not required even if the flow is stopped, provided the syphon was not drained. A limiting factor in considering a pipeline syphon as a design option is the maximum lift (i.e. vertical distance from source pond water level to summit of pipeline syphon) which is approximately 9 m or less, depending on pipeline syphon features and site conditions. A pipeline syphon can be quickly constructed from readily available materials including steel, concrete, polyethylene, or PVC pipe. It is particularly well suited to many of the unique conditions often encountered at mine sites. This paper identifies situations that can sometimes be best resolved using a pipeline syphon. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

Jan 1, 2005

By Lawrence Winter

why are these deposits significant? (i) economically and (ii) in a VMS/geological context. ?Significance of the tectonic setting. ?New understanding of the regional geology: volcanic stratigraphy, first geochronologic data. ?Deposit geology: paleomorphologyof the seafloor setting. ?Lessons and conclusions ?Regional Potential

May 1, 2006

By T. Chong, R. Pesalj, B. Marchant, Z. Nikic

"The Mount Polley copper/gold project is located in central British Columbia and is currently being developed by Imperial Metals Corporation. Extensive laboratory and pilot plant testing was required to develop acceptable metallurgy for recovery of both sulphide and oxide copper-gold mineralization. Copper recovery is highly sensitive to oxide copper content of the feed whereas gold is primarily associated with the copper sulphide minerals. A conventional flowsheet where sulphide flotation is followed by sulphidization and oxide scavenging is described. The conventional flowsheet was used in a feasibility study which resulted in a favourable production decision at Mount Polley. Detailed engineering and permitting are in progress.More recently, laboratory and pilot testing of a new flotation reagent, S-6493*, an oxide specific collector, has indicated that improved copper recovery can be accomplished with reduced reagent consumption, including elimination of the sulphidization step, using S-6493 compared with the conventional flowsheet. The comparative metallurgical results using S-6493 and conventional sulphidization methods are presented, from both bench scale and pilot testing. Comparative economics of the conventional flowsheet and that using S-6493 are also presented. Advantages of S-6493 include reduced reagent costs, increased revenues from additional copper recovery, and overall reduction in capital and plant operating costs due to the simplified flowsheet. INTRODUCDONThe Mount Polley copper/gold property is located in Central British Columbia, 56 air kilometres northeast of Williams Lake. The first recorded exploration was in 1964. By 1989, a total of 238 diamond drill holes, totalling 27, 522 meters, was completed to detail reserves on the Mount Polley prospect. A number of drill core composites were submitted, containing a variety of oxide copper levels, for metallurgical flowsheet development. Six bulk samples were collected from surface trenches for additional bench scale testing and for pilot plant testing."

Jan 1, 1991

By Neil H. Brown

Outline ? Cameco - Cigar Lake ? Cigar Lake Mine Development ? MDS #1 ? MDS #1 Improvements ? MDS #2 ? MDS #2 Improvements Pending ? Acknowledgements Mine Development System ? Mining methods tested and developed over the years ? Construction began officially in 2005 ? Water inflow events in 2006 and 2008 ? Successful dewatering and re-entry in 2010 ? Remediation continues ? Production target is mid-2013

Oct 1, 2010

By D. Settles, R. Rose, P. L. Dunn

"A new mineral sands operation is being developed in Georgia by Southern Ionics, Inc. (SII). Prevailing mineralogy and certain design constraints required detailed testing and circuit analysis to create a robust separation processes. The floating wet concentrator plant (WCP) and mineral separation plant (MSP) flow sheets were designed based on historical testing information and recent SII test campaigns on various composite feed samples. The flow sheets were finalized through rigorous process and orebody sequence modeling.The process uses traditional physical separation equipment; however a new MT spiral, the MG12, was selected for use on board the WCP for roughing duty. The MG12 spiral is a two-stage, twelve-turn spiral that has been proven to achieve very high recoveries of heavy minerals. The floating plant includes feed desliming operations, a central MT surge bin for optimum spiral circuit feed control and ancillary operations for concentrate and tailings handling. Scrubbed heavy mineral concentrate (HMC) is then transported to the MSP for concentration of the titanium and zirconium bearing mineral fractions.The testing, flowsheet development, and plant design will be described and explained, and a brief summary of the current project status will be given.IntroductionSouthern Ionics Inc. (SII) is a privately held chemical manufacturing company, founded in 1980 by Milton Sundbeck. SII focuses primarily on the sale of specialty and intermediate inorganic chemicals. Core markets include cement and refinery catalysts, molecular sieves, zeolites, pulp and paper, pharmaceuticals, TiO2 and water treatment. SII is built on the four cornerstones of service, quality, technology and delivery with all SII facilities ISO certified and key products used in potable water treatment certified to NSF standards. SII owns and operates its own transportation fleet and is focused on being a low cost producer, committed to safety and the environment."

Jan 1, 2015

By J. Yue

"Mount Milligan mine is located in northern British Columbia. The concentrator employs conventional SABC grinding circuit with bulk sulphide flotation processes. Commissioning started in September of 2013 and nameplate production of 60,000 TPD was reached in the fourth quarter of 2015. As is typical with many mill ramp ups, bottlenecks developed as throughput increased. Since then, plant modifications and new control philosophies in the comminution and flotation circuits have been implemented and evaluated. The mine-to-mill collaboration played a key role in reaching target throughput rates by improving blast fragmentation and implementing temporary pre-crushing. Results of the projects as well as ongoing challenges/bottlenecks and solutions will be discussed.IntroductionMount Milligan Mine is a copper-gold producer located approximately 253 km northwest of Prince George in British Columbia. Production commenced in September 2013 and reached nameplate capacity of 60,000 TPD in December 2015. Average head grades for the mine life average 0.18% Cu and 0.39 g/t Au.Circuit DesignOriginal process design began with run-of-mine ore from the pit crushed through a 60-110 gyratory crusher, conveyed to a live ore stockpile and fed to the mill via four variable apron feeders. The concentrator circuit employs SAG mill - Ball mill - Pebble Crusher (SABC) grinding configuration to grind the ore down to a target P80 of ~200µm. It is then fed to two parallel trains of flotation tanks, each consisting of five 200 m3 tank cells with the first two being roughers and last three being scavengers. Concentrate streams from roughers and scavengers are separately reground with a closed circuit Tower mill and two open circuit ISA mills operating in parallel, respectively.Three stages of cleaners upgrade roughers/scavenger products to 25% Cu followed by a cleaner scavenger stage. The final concentrate is then thickened and filtered to approximately 9% moisture and shipped off site (Figure 1)."

Jan 1, 2017