Search Documents

By W. B. Gallup

"The Athabasca Bituminous Sands have been subject to sporadic investigations since the beginning of the century. It is probable, however, that much of what has been learned and achieved concerning the deposit has been accomplished in the last few years.Current exploratory techniques, generally speaking, involve a moderate amount of coring. Electrologs and often radioactive logs are run on most holes and certain types of these archieved excellent qualitative analysis when backed up by some core analysis for calibration. Exploration - is moving back from the river and consequently a permanent network of access roads has been developed within the last few years. Most of the operations take place in the winter time. There are about 90 permit holders at the present time.Some exploratory techniques are set up to go into recovery experiments where rich tar beds are found. It is probable that in the final analysis there will be several successful methods of extraction and that both mining and various in situ techniques will be applicable depending upon the problem locally."

Jan 1, 1960

By A. J. Baer

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE EXPOSED PART OF THE GRENVILLE PROVINCE is the southeastern part of the Canadian Shield, characterized by crystalline rocks with K-Ar ages of about 1,000 million years. Its Canadian portion is bounded on the southwest by Georgian Bay •and by Paleozoic sediments south of a line passing through Orillia and Kingston, on the southeast by the St. Lawrence River valley and the north shore of the Gulf of the St. Lawrence, on the east by the coast of Labrador and on the northwest by the Grenville front, a linear tec-tonic feature that is a metamorphic transition zone and/or a fault. Rocks located to the southeast of the front have younger K-Ar radiom€tric ages than rocks located to the northwest of it.The region is formed of complexly deformed and highly metamorphosed crystalline rocks and in part differs from other areas of the Canadian Shield by the presence of large amounts of crystalline limestone and bodies of anorthosite."

Jan 1, 1970

By Roger Francis

There is increasing use of acid leach extraction methods at elevated temperatures and pressures by the mining industry. In many locations there are limited supplies of fresh water, and waters with higher chloride contents must be used, making conditions more corrosive. The fluids downstream of the main autoclave are hot, acidic, oxidizing and contain chlorides and present a challenge to the mining community to ensure reliable operation. Zeron 100 is a high strength superduplex stainless stee, that offers high corrosion resistance at a cost effective price. The paper presents a combination of laboratory data and service experience, particularly in the aggressive fluids found in downstream processing.

Jan 1, 2010

By D. Atkinson

"Porphyry molybdenum-tungsten mineralization on the east flank of Hudson Bay Mountain crops out over 5 km2 and is intersected to depths of 2 km. Features such as a hornblende-biotite aureole, mineralogical zoning and dike, vein and fracture geometries within lithologies of the Middle to Lower Jurassic Hazelton Group and Cretaceous Skeena Group reflect an intrusive complex, the Upper Cretaceous to Early Tertiary Hudson Bay Mountain stock which has been intersected by drill holes. The stock is believed to be the mineralizing agent. A southeast-dipping granodiorite sill has been outlined by drilling within the Hazelton Group. Molybdenite and scheelite veins cut all rock types; however, the granodiorite sill hosts a higher density of fine-grained, banded, quartz-molybdenite and pegmatitic quartz-molybdenite veins reflecting a competency contrast between the intrusive sill and other country rock. Due to the relative abundance of these veins, grade is higher within areas of the sill. Above the 15000£ cross-cut 20.6 million tonnes grading 0.401% MoS2 and 0.041% W03 have been defined. During exploration of the deposit sampling procedures had to be adjusted because of the nugget effect attributed to drill intersections of banded and pegmatitic veins.IntroductionMolybdenite was discovered in outcrop at the foot of Kathlyn Glacier on Hudson Bay Mountain and first reported by the Geological Survey of Canada in 1944. The deposit has several names: Hudson Bay Mountain or Glacier Gulch, both after its location, and Yorke-Hardy after the original staker.The deposit is on the east flank of Hudson Bay Mountain, 9 km northwest of Smithers, west-central British Columbia, within NTS area 93L/14 (54° 49' North, 127° 18' West, Fig. 1). Hudson Bay Mountain, on the southern edge of the Bulkley Valley, is a dominant topographical feature reaching 2590 m elevation. Mineralization is partly overlain by the Kathyln Glacier which is visible from Highway 16. Access to the 3100 m of underground development is from a portal at 1066 m elevation on the east slope of Hudson Bay Mountain."

Jan 1, 1995

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By John T. Ling

"This paper describes the operation of a rope haulage used as the main system of transportation in an underground coal mine. Prince Colliery, which is operated by the Cape Breton Development Corporation, has been in operation for 23 years and produces 1.2 million tonnes of coal annually. The mine extends a distance of 8000 metres under the Atlantic Ocean. All personnel and supplies are transported by means of an endless rope haulage system consisting of a train of rail cars that are operated by an electric engine on surface. The wire rope is 15 km long and weighs 63 tonnes. The system is believed to be the longest of its type used in an underground coal mine. The design of the system, safety features of the haulage, and problems encountered during the design and construction are described. IntroductionCoal has been mined commercially in Cape Breton, Nova Scotia since the 1800s. Several coal seams that are part of the Sydney coal fields, dip toward the north and northeast out under the Atlantic Ocean at angles between -4 and -15 degrees. Coal has been economically mined at depth in excess of 1200 m and more than 11 km from the coastline.Traditionally, single and double drum hoists have been used to haul the coal to the surface and also for transporting the workers and the materials required for mining up to 8 km. With the introduction of mechanized mining methods in the late 1960s, conveyor belts began to replace rope hoists for coal transportation. Improvements in hoisting system design also allowed for drums that could wind up to 6100 m of 32 mm wire rope in 15 layers.These hoists are commonly referred to as “drop hoists” because they take advantage of the gradient of the slope to assist in allowing the mine car train to reach the end of travel. The cars travel on steel rails and the rope is guided by rollers to reduce friction in the system."

Jan 1, 1999

By C. Dragusanu, J. Sims, J. Connolly

Based on a statistical analysis of the categorical and numerical data from the established geological model, a geochemical classification of mineralization has been shown to be objective in nature and correlated to the envisioned metal extraction process. Multivariate chemical classification has the potential to discriminate within a combined response from different types of alteration and metal abundances. Distinct domains of chemical response determined by clustering analysis were used as a validating criterion for a geologically driven metallurgical testing program. The groups established are spatially linked to the geological process responsible for their genesis, providing clarity in geometallurgical and resource modeling.

Jan 1, 2011

By Luke Meers

Roadway development rates in Australian underground coal mines are failing to keep pace with modern longwall systems and are unlikely to sustain further improvements in longwall productivity into the future unless step change improvements to roadway development equipment and practices are made. Bottlenecks which limit and constrain improved production and impact the safety of operators have been identified through a series of industry surveys, with the manual installation of strata support materials, consumables delivery, coal haulage and monorail installation being highlighted as major areas to improve development performance. This paper looks at research being carried out at the University of Wollongong in designing an integrated system approach for the fully automated handling and installing of development consumables, and the systems required to support these activities. A series of hard automation manipulation devices have been demonstrated in surface trials and the results indicate that rapid roadway development can be achieved.

Aug 1, 2013

By D. Verhulst

The Altair process digests ilmenite concentrate in high-chloride HC1 solution, with complete dissolution of titanium and iron. The Fe(III) ions are reduced to the ferrous form, and the solution is cooled to produce crystalline ferrous chloride. Titanium is transferred by solvent extraction into a purified, concentrated Ti stream, which is spray-hydrolyzed to produce TiO2 hydrate. The hydrate is further calcined with additives to generate a high-quality pigment. All the chloride streams are recycled. In the original flowsheet, the iron chloride is pyrohydrolyzed by spray roasting to regenerate 18% HCl, which is subsequently converted to HC1 gas and water by pressure-swing distillation. A modified flowsheet includes an alternative to iron chloride spray roasting, producing more concentrated HCl and decreasing the amount of solution to be distilled. Improvements in digestion, solvent extraction and final pigment production are also introduced. A 100 t/y pilot plant is being built and will test the new concepts and confirm the overall water, acid and impurity balances of the process.

Jan 1, 2006

By H. G. Harper, R. C. Hart

"The Mississagi quartzite is the basal formation of the Quirke Lake trough. As it is traced around the rim, a gradual change in dip is observed, as follows:Northwest corner 50 degrees south.Algom Quirke mine 34 degrees south.Quirke Lake 25 degrees south.Whiskey Lake 22 degrees west.Pecors Lake 25 degrees north.Algom Nordic mine 18 degrees north.Elliot Lake 11 degrees north.Pistol Lake 5-7 degrees west.Thus the apparent synclinal axis is a curving east-west line lying closer to the north limb than to the south. The axis appears to plunge west at about 5 degrees.The Huronian sediments lie on a basement of granites, gabbros, and volcanics. Diamond drill evidence indicates that this basement has a surface of peneplanation, and that the areas of soft basic rock have a smoother topography than the granite. For the most part the orebodies at the Quirke and Nordic mines overlie a basement of soft basic rock.The Mississagi formation is the host rock of the deposits, and its primary structures are suggestive of the conditions under which the conglomerate beds were deposited. Cross-bedding is common, although normal bedding varies from thick to thin to essentially lacking. Grain gradation is not common. Where coarse and fine grains occur together, the coarse tend to be more rounded than the fine. These features are characteristic of shallow-water deposits, laid down above the lower limit of wave action. Therefore, the quartz-pebble conglomerates probably represent ancient water courses, bays, beaches, and bars.The causes governing the creation of the trough can only be conjectured, but there is evidence that both subsidence and compressive stresses played active roles. Drag-folds in argillite beds near Whiskey Lake indicate compressive stress. On the other hand, gentle crumpling in thin-bedded limestones on Quirke Lake is probably due to pre-induration slumping and folding. If strong compression had been widespread within the trough, one would expect drag-folding and shearing of the incompetent beds to be more general. Two large-scale, fold-like structures were mapped by Collins, but their axes do not parallel the trough axis, and they are therefore not related to the major structure."

Jan 1, 1949

By R. Bruce Graham

The formation, evolution and classification of peat bogs is discussed. Factors resulting in the internal and external morphological changes in a bog are described. The fibrous, absorptive and sterile properties of peat moss account for its widespread use in horticulture and related fields. These properties also account for its usefulness as a binder in pelletizing, as an insulating material in bat tons and in panel construction. Peat, the humijied product of peat moss is used in market gardening and sod growing. It is utilized in Europe as fuel. It is a source of activated carbon and gas. Potentially peat can be used to produce waxes, resins, tannins, cellulose, hemicellu/ ose, humic acids, lignin and hymatomelanic acid. At present other cheaper sources are available.

Jan 1, 1984

By Peter F. Pullen

The need to apply the latest available technology to develop better tools and methods to meet problems in the mining industry was recognized by six of Canada's leading mining companies. As a result, MIROC (Mining Industry Research Organization of Canada) was chartered to identify problem areas in Canadian mining and to have research carried out to develop the tools and equipment to meet these perceived needs. The initial activity of MIROC has been in the environmental field, with improved clothing and protective devices being developed by contractors. Work clothing for miners is now being field tested. Respiratory protection and a new personal light source combined in a new "space-age" helmet are about to be issued for testing. Further developmental work is being carried on to offer these units and probably other personal protective devices on an individual basis as well as in a combined package.

Jan 1, 1979

By M. S. Millman

Close monitoring of performance at each process stage, from raw material through to finished product, is vital for operational consistency and the production of high quality steel. However, many of the integrated iron and steelmaking process route stages operate under such severe conditions of temperature, dust, water, thermal radiation, vibration, pressure, vacuum, extreme dynamic events, high material flows, corrosion, erosion, electrical-noise, electromagnetic-noise, or audio-noise that, in general, it is a very difficult challenge to obtain useful information for control. Thus, state-of-the-art non-contact and remote sensors are applied to help monitor and control specific process operations. Often, these sensor systems have been developed especially for the steel industry and they are based on four principal technologies: Laser, Microwave, Electro-Magnetics and Thermal Imaging with supporting technologies such as: X-ray Fluorescence, Audiometry, Digital Image Processing, Radio Telemetry, GPS and many others. These advanced sensor technologies are reviewed with respect to their application at various stages along the integrated process route.

Jan 1, 2004

This paper deals mainly with the modernization in the coal loading system at the loading piers of the Dominion Coal Company, Ltd., Sydney, Nova Scotia. The history of the operation is briefly outlined, and the construction of the Company's new pier is described in considerable de-tail. Particular attention is paid to the bins and conveyors, and to the loading tower. The paper concludes with a description of the S.S. Cape Breton Miner, built specifically for the coal trade, and the unloading facilities at Lakeview, Ontario. Coal Shipping at Sydney C OAL from the mines operated in Cape Breton by the Dominion Coal Company, Limited, has been shipped from the International Piers, situated on the east side of Sydney Harbour, for over sixty years. There were three piers, of which two were active-ly used in the shipping of coal until 1964. Nos. 2 and 3 were high piers about 600 feet long, of wooden construction throughout. They were founded on' rock-filled cribs and creosoted piles driven into the harbour bottom, and each had two decks which carried standard-gauge railway tracks.

Jan 1, 1965

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By E. J. Burrough

Coal Reserves The Crowsnest Pass coal fields form part of a greater area which comprises the Inner Foothills belt of the Alberta coal fields and the southeastern coal fields of British Columbia. The most valuable and most extensive reserves of the bituminous coals of Canada are concentrated in this?area, of which the Crowsnest Pass fields form an important part. The extent of these coal reserves together with those of the rest of Canada were recently studied by the Geological Survey of Canada for the Royal Commission on Coal of 1946 (1). Quotin from the report, it is of interest to note that, prior to this work, the most widely known, and in fact the only Canadian-wide estimates of, coal reserves of Canada available to the Commission were those prepared by Dr. Dowling in 1913 (2). At that time it was estimated that Canada's reserves of coal were over twelve hundred billion tons. The more recent estimates of mineable coal for the whole of Canada are of the order of 10 per cent of that figure and are reported. as 99 billion tons, which is further reduced to 40 billion tons on the basis of the estimation of recoverable coal. This considerable divergence in estimated reserves is explained in part by the big difference in the bases of measurements. For example, in the original report, seams of one foot occurring at a depth of 4,000 feet were included in the estimates.

Jan 1, 1951

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

By E. Gaucher, D. C. Gagnon

"The paper refers to methods and concepts used in the computer treatment of banks of geophysical, geochemical and geological data, relating to the exploration of massive sulphides. In particular, a data bank of 400 drill holes on independent conductors can be used to calculate probability levels of intersecting a certain quantity of sulphides according to the characteristics of the conductor. Inversely one can, using the data bank and some cost assumptions, simulate and optimize the cost of intersecting a certain quantity of sulphides by selecting drill targets among conductors according to conductivity, magnetism or gravity. Problems of noise, inherent in any simulation, are illustrated in this paper by the results of a study of the nomenclature of volcanic rocks of 27 drill holes by forty geologists. Compilations of data banks are long and timeconsuming, and it would help to standardize to allow exchange of data. We believe that such efforts may result in the discovery of more mineral deposits and at a lower cost. The present study is supported jointly by SOQUEM The New Jersey Zinc Co. and Cominco Ltd."

Jan 1, 1973

By G. H. Montgomery

THE PROPERTY of Aunor Gold Mines, Limited, consists of eleven claims, located in Deloro township, approximately three miles southeast of the town of Timmins. Production began in 1940 and currently the mine is operating at a rate of 485 tons per day. GEOLOGY AND MINE DEVELOPMENT The ore zone at Aunor occurs in altered lavas bounded on either side by soft talc-chlorite schist, locally known as 'soapstone'. The zone has a strike of N.80°E, dips 60° North, and varies in width from 0 to 250 feet. Within this zone the main orebody has a westerly plunge, away from the No. 1 shaft area (Figure 1). The mine is developed by a vertical three-compartment shaft from surface to the 3,082-foot horizon. Working levels are spaced at 125- foot intervals from the 625-foot to the 1,625-foot horizon, from which to tl1e 2,125-foot level the interval is 250 feet.

Jan 1, 1957

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978