Search Documents

The Silvermines area of north County Tipperary in Ireland has experienced mining activity for over a thousand years, with lead, zinc, copper, barite and sulphur being extracted from a series of Carboniferous limestones. The last mine to operate in the area was closed in 1993. A legacy of contamination and derelict surface structures remain. Following the death of cattle in the vicinity in 1999, a governmental Inter-Agency Group was established to conduct an investigation. The ?Silvermines Rehabilitation Project? resulted, and included a proposal for the development of a Mine Waste Management Facility (MWMF) to act as a repository for waste materials from problematic sites across the area. The nature of the setting supported an effective solution from both a cost and performance perspective; and with limited maintenance requirements. Locating the MWMF where most wastes were identified would help minimise handling and relocation of materials. This position coincided with an area of artesian groundwater pressures. The resulting MWMF design consisted of a perimeter engineered embankment with the crest elevation designed to just exceed the groundwater piezometric surface. The base would remain unlined and groundwater permitted to rise up into and saturate the contained in-situ tailings deposits and imported mine wastes. The proposed system thus benefited from the ?wet cover? approach to minimising further oxidation of wastes and metal leaching, but without the usual accompanying outward hydraulic gradient and leachate management issues. A sub cap drainage layer with downstream outlet was incorporated to prevent any possibility of hydraulic rupture following an unexpected rise in groundwater heads. Leakage rates from the MWMF were deemed to essentially be driven by surface infiltration rates alone (characteristic of a ?dry cover? approach), with the proposed composite capping system simulated to perform at an infiltration rate of less than 1 mm per year. A toe drain was incorporated with the perimeter containment system, and this collection together with diverted neighbouring drainage was directed under gravity to a dedicated Passive Treatment System (PTS). Overall, effluent water quality from the PTS has been predicted to reflect an annual mass metals removal in the order of 95% below baseline.

Aug 1, 2013

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By Magella Pelletier

"IntroductionDepuis une vingtaine d'année, les nombreux travaux de géochimie effectués par l'industrie privée et les milieux gouvemementaux ont permis:• de découvrir de nombreuses zones minéralisées a valeur économique;• d'identifier et de vérifier certains patrons de dispersion géochimique au-dessu s de secteurs minéralises déjà connus;• de favoriser le développernent des techniques analytiques;• de forcer le développement d'une mise en carte des résultats d'analyse, qui soit plus adéquat afin de permettre une meilleure interprétation géochimique.L'une de ces cartes géochimiques qui permet le mieux de mettre en valeur les données analytiques et qui fut instaurée au debut des années 80, est la carte d'interprétation géochimique par pondération.Cette carte numérique semi-quantitative, qui est construite à partir des données de base et de l'importance des éléments indicateurs pour une substance donnée, permet d'identifier et de définir des zones possédants de fortes probabilités pour la recherché de sources minéralisées."

Jan 1, 1987

By Ralph V. Stewart

"The asbestos orebody is contained within ultrabasic rocks of Precambrian age, being located in the continuous permafrost zone of the Quebec Ungava Peninsula, some 300 miles north of the tree line at approximate latitude 61'49' and longitude 73°58'.The asbestos deposit is at the western tip of a folded ultrabasic sill complex which trends northeast and covers an elliptical area 4.5 miles wide by 15 miles long. Locally. the asbestos occurs in. a completely serpentinized dunite rock. The principal rock types in the vicinity of the ore-body originally consisted of dunite, peridotite and pyroxenite, all of which have experienced at least two periods of alteration, so that no fresh rock now remains.The main ore zone in the open pit is approximately one quarter mile in length, 150 to 200 feet in width, and plunges at 25 to 30 degrees in a northeast direction below surface, to a vertical depth of at least 1,200 feet, Consider¬able tectonic activity resulted in favourable structural conditions which culminated in the formation of the ore zone in its present form.The deposit consists principally of cross-fibre ""gash type"" veins which vary in length from several inches to several feet. The principal fibre vein direction is parallel to the dip of the enclosing serpentinized dunite and sill complex.Some of the problems encountered during diamond drill¬ing in permafrost are briefly discussed."

Jan 1, 1976

By Marvin E. Lane

Viburnum, located in the foothills of the Ozarks in south-east Missouri, is the site of a modern lead mining and milling operation. Two mines are currently producing a total of 5,000 tons per day and a third mine is in the final development stage, with full production scheduled for late this year (1964). These mines will supply the tonnage required to keep the Viburnum mill operating at a full capacity of 7,000 tons per day for many years. The efficient underground mining operation is completely trackless. Drill jumbos are used to break the ore in a room and pillar method of mining. Transloaders, or St. Joe shovels, and trucks do the loading and hauling. The Viburnum mill has a world-wide reputation as a most efficient operation. This is due to the extensive use of automatic process controls, and labour saving materials handling facilities. Introduction THE St. Joseph Lead Co., has operated lead mines in southeast Missouri for 100 years. These operations have been confined largely to the area called the

Jan 1, 1964

By Finley A. Campbell

THE Quemont and Horne mines are located at Noranda in north-western Quebec. As shown in Figure 1, the Noranda area lies between the Cadillac-Bouzan fault zone on the south and the Porcupine-Destor fault zone to the north. Both of these major structural lineaments appear to be geometrically, and possibly genetically, related to the Grenville Front. The regional geology has been discussed by Wilson (12), Cooke et al. ( 2), and others. The geology in the Noranda vicinity, as compiled by Dugas and Gilbert ( 3), is shown in Figure 2. The Cadillac-Bouzan fault zone separates the dominantly Temiskaming-type sediments in the south from the Keewatin-type canic rocks to the north. These volcanics, which vary in composition from rhyolite to andesite, form a broad anticlinorium with a general eastward plunge. A succession of dioritic stocks, sills and dikes have been mapped in the area. The principal granitic rock masses include the Powell, Flavrian and Dufault stocks.

Jan 1, 1962

By R. F. Tylecote

"The closure of the iron and steel making plant at Consett in Durham in 1980 marked the end of an era-a long era in the world's iron and steel making history. Iron had been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century.The paper describes sites in the area that first worked the bloomery process and then, in the 16th century, as did most of Europe, graduated to the blast furnace process. The main emphasis is on the early introduction of coal to iron making at the end of the 18th century and the use of the steam engine to render integrated sites possible.IntroductionIron has been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from clear evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century. Like many other countries, the United Kingdom benefitted from the visits of foreign observers, such as Jars, Svedenstierna, de la Houliere and Dufrenoy, who left detailed records. In modern times, information gained from excavations of iron and steel making sites has supplemented the historical record.Natural ResourcesUp to the end of the 19th century, the industry was wholly dependent on its own resources. Iron ore, limestone, wood, coal and water power were all found a short distance away from the main valleys of the Tyne and Wear. The main sources of iron ore were the coal measures, with rider ores from the lead vein s in Alston and Weardale, and carbonate ores from shale horizons in the Carboniferous limestone. Good coking coal was available from West Durham and reasonable coal from the Tyne valley and Northumberland limestone. Limestone was plentiful."

Jan 1, 1983

By George W. Bain

Summary During the last three years the discovery of gold in the belt of volcanic and sedimentary rocks extending eastward from the Porcupine and Kirkland Lake gold-fields has caused a great deal of excitement in mining circles. The area is heavily drift covered, and every aid to the location of veins is eagerly grasped. A knowledge of the physiographic history of the area is of the utmost importance in the application of many of these aids. Evidence is presented to show that glacial erosion has lowered the general elevation very little below the pre-glacial level, and that many glacial erratics have been carried less than three miles southward. Probably a knowledge of the general geology of a: region was never more necessary to the understanding of the distribution and continuation in depth of the mineral veins than in this area. Four distinct granites occur in the region, and gold-bearing veins are genetically associated with only one of these. Two types of quartz-feldspar porphyries have been found, only one of which has any bearing on the locus of the mineral veins. Many other examples of this complexity of associations might be cited, but everyone goes to show that in most cases the economic importance of the deposits can be realized only after the regional geology is understood. A series of sandstone, limestone and shale intruded by granite lies unconformably below the Keewatin lavas. The latter are intruded by a gneissoid granite and are overlain unconformably by the thick series of Timiskaming greywackes and silts. These are intruded by carbonated syenites and syenite porphyries which have since been rendered somewhat schistose.

Jan 1, 1927

By I. Vazaios, M. S. Diederichs, N. Vlachopoulos

"As rock engineering moves from continuum to more discontinuum approaches for modeling, the engineer must make decisions regarding the degree of complexity to simulate for a given application, balancing the level of structural detail within the rockmass model with computational cost and result accuracy. It is important to consider that model does not need to include all the existent fractures and that representative geometrical properties for a given rock mass volume can be defined including only major structural entities.Within this paper, the scale-dependency associated with the geometrical properties of fractured rock is investigated utilizing a Synthetic Rockmass (SRM) approach with a view to characterize such ground to aid in the design of geotechnical works. In terms of process, the concept of the Representative Elementary Volume (REV) is used to determine the equivalent structural properties of the rockmass in order to justify the applicability of far-field behaviour of such ground. A large size Discrete Fracture Network (DFN) measuring 60m x 60m x 60m has been generated using the structural data obtained from LiDAR scanning of the Brockville Tunnel, Ontario, Canada. A number of DFN samples of varying sizes are extracted from the master network, generated using MoFrac, in order to be used as a the basis of the structural analysis of the rockmass. Volumetric measurements for the density and the intensity of jointing are employed in order to approximate the geometrical REV for the networks.In this paper a complete methodology of how to generate a DFN from LiDAR data and its analysis in order to determine the size of a geometrical REV is demonstrated. For the specific rockmass found in the area of the Brockville Tunnel, a geometrical REV measuring 3.5m x 3.5m x 7m is established. The results are generally in good agreement with the in-situ observations."

Jan 1, 2015

By A. G. Spencer

"The horsepower required to drive large grinding mills has increased dramatically during the past ten years. Limitations on the amount of power which may be transmitted by a single gear and pinion have resulted in the application of multimotor drives, with consequent loadsharing problems. It has also sparked the development of some entirely new drive concepts. In addition, the severe demands made upon the electrical system during the acceleration period have required that the selection of motors and electrical system design be closely coordinated. Moreover, the installation of such large process units results in downtime being very costly. The equipment selected and the plant maintenance philosophy must therefore be such as to minimize the risk of unscheduled downtime."

Jan 1, 1972

By M. F. Lopez, A. J. Mattus, S. B. Magid, D. B. Mobbs

"The use of Caro's acid as a replacement for hydrogen peroxide for the oxidation of vanadium prior to solvent extraction resulted in a 56% reduction in oxidant usage when compared on an equivalent hydrogen peroxide basis. Comparative oxidation tests, using two actual uranium mill raffinates, resulted in premature precipitation of an amorphous ferric vanadate when hydrogen peroxide was used to oxidize one of the raffinates containing a high iron to vanadium ratio. The use of Caro's acid eliminated the precipitation problem, thereby permitting the adjustment of the raffinate pH to a higher, more favourable level prior to solvent extraction.Potentiometric characterization of the raffinates revealed that vanadium is responsible for the inefficiency of hydrogen peroxide compared with Caro's acid, with the oxidation efficiency of iron being the same for both oxidants. A limiting potential between 720 and 740 mV was observed when using hydrogen peroxide, while, when using Care's acid, potentials approaching 1200 mV were achievable.A four-stage, countercurrent extraction performed on the oxidized raffinates did not reveal any operational problems. The extraction efficiency and the extraction coefficient were found to be higher when Caro's acid was used as the oxidant, as opposed to hydrogen peroxide.IntroductionMost vanadium is recovered as a by-product of some other process: leaching of Carnotite uranium ores, oil fly ash, phosphate rock or chromite processing. The major source of vanadium has been from uranium mills incorporating acid leaching of Carnotite ore s at elevated temperatures and pressures. The by-product recovery of vanadium from uranium ores of the Uravan Mineral Belt, located in the Colorado Plateau , is a common occurrence when vanadium recovery is economically viable."

Jan 1, 1983

By A. F. Brock

Introduction During the past ten years, shaft sinking has been going on continuously at Inco and new shafts and shaft extensions have been sunk under a broad diversity of conditions. The Murray mine and the Stobie section of the Frood-Stobie mine have?been opened and a main hoisting and supply shaft has been sunk at each of these mines; No. 2 shaft at Murray was sunk initially from surface to 1,960 feet and is now being extended; No. 7 shaft at Stobie was sunk from surface to 3,105 feet. No. 2 shaft at Garson has been extended from 2,200 feet to 3,200 feet in depth. At Levack, No. 2 shaft is being extended from 1,860 feet to 2,850 feet for ore hoisting from the 2,650 lev el. At Creighton, No. 6 shaft, collared on 52 level, was sunk 1,740 feet to a total depth of 5,563 feet below surface. It is the deepest Inco working. At Creighton, also, No. 7 shaft is being sunk from surface to the 30 level to handle the ore from caving operations. Ail Inco main hoisting and supply shafts sunk during the past twenty years have been vertical rectangular shafts equipped with two cages and two ore skips. The cages are standard and interchangeable for all shafts except Garson No. 2; they are single-deck, 13 ft. 4 in. by 5 ft. 2 in. inside and are designed to carry a maximum material load of 16,000 lb. The man load is 48 men. Skip capacities at the several shafts vary from 8 to 15 tons. Forty-two hundred feet bas been established as the standard vertical lift, and the permanent hoisting equipment at each shaft is designed for eventual hoisting from that depth.

Jan 1, 1950

By Ali Montaser

Hauling trucks are important part of equipment fleets for large earthmoving operations such as those encountered in dams and highway construction projects. This paper presents an automated methodology for tracking and estimating productivity of hauling trucks fleet operations in near-real-time. Recent advancement in automated site data acquisition technologies made their use in tracking and monitoring of construction operations feasible. However, these technologies fail to track hauling truck fleets due to the change in the cut and fill locations from one cycle to another; making tracking and progress reporting difficult and inaccurate. In addition, there is very little work done utilizing data sensed directly from equipment, for example sensing when truck dumping bed is raised during the dumping process. The technologies deployed in the developed method are Radio Frequency Identification (RFID) and equipment control sensors. Low cost passive RFID tags are attached to hauling trucks and fixed RFID readers are attached to loaders or excavators. The read range of the used RFID tag is centimeters, to be activated only when a loader with an attached RFID reader is loading a truck. On the other hand, control sensor is connected to the truck control system and operated by the motion of its movable bed. The function of control sensors is to record the signal time when the truck operator gives order to the truck control system to raise or lower truck bed. The captured data is then transferred wirelessly from the RFID reader and control sensor to a computer housed in one of the temporary offices onsite and subsequently to the main server in the contractor?s head office. Fusing the data captured from RFID reader and control sensor is used to identify loading, travel, dumping and return time that constitute the hauling truck cycle time. The collected data is analyzed and processed automatically, without human intervention, to calculate the productivity of the hauling truck and to report it directly to onsite personnel. Relational database is developed to support the implementation of the proposed method. The developed database is used to process the data captured by the RFID and the control sensor to calculate the productivity achieved in cutfill operations in near-real-time. The developed methodology is expected to facilitate early detection of discrepancies between actual and planned performances.

Aug 1, 2013

By E. T. Turner

Introduction 1n assembling material for this paper on Wood Refuse Burning 1 turned first to the records of our early studies of the problem in order to learn how and why certain basic decisions were arrived at and also how it came about that the completed central steam plant differed so much from the original plans. It may be of interest, therefore, to outline the engineering problems as they presented themselves in the early part of 1948, and to indicate the economies involved. Although the principle of using wood refuse as boiler fuel instead of burning it to waste was quite sound, and in fact the practice had been in use for a long time in the boilers of many lumber companies, there was some guesswork as far as Hollinger was concerned in deciding how best to handle the large quantities of wood refuse involved and as to the type of boiler equipment necessary to .burn it efficiently. These problems will be examined first. Hollinger Boiler Equipment in 1948 Hollinger had four separate boiler houses, at Main, No. II, and No. 19 shafts, and a small unit at the compressor plant for heating purposes. Main and No. Il boiler houses operated all the year round; No. 19 and the compressor plant only in the winter. At Main there were four 36-year-old HRT boilers with total available h.p. of 500, at No. II, three 30-year-old HRT boilers with 195 available h.p., and at No. 19 two old field-type locomotive boilers capable of producing 95 h.p.

Jan 1, 1951

By W. Dingley, G. R. Hoey

"Thirteen Canadian sulphide ore mines were surveyed for corrosion control. The mines visited were a small, yet representative, proportion of this segment of the Canadian mining and metallurgical industry. Information on metallic corrosion and methods used to control it in underground workings and mills was gathered (a) by discussing corrosion problems with company personnel, (b) by examining equipment and structures during under-ground and mill tours, (c) by photographing corrosion sites, and (d) by collecting and analyzing mine water samples.The corrosion survey, which is summarized in the re-port, leads to the following general conclusions. Mine environments are corrosive, particularly when the mine w1a-ter is acidic. Because of a lack of good corrosion control measures, excessive deterioration of equipment due to corrosion occurs in mines. Mill environments are also corrosive, but in some cases good preventive measures are being taken to effectively control corrosion losses.Ways to reduce corrosion losses in sulphide ore mines and mills are discussed. The main areas for more corrosion research and development are selection of materials of construction, protective coatings, cathodic protection, inhibitors, equipment design, and mining and milling practices."

Jan 1, 1971

"6.1. Mineralogical Techniques ApplicableTo the Platinum-Group Elements6.1.1. IntroductionThe named platinum-group minerals (PGM) usually occur as grains smaller than about 200 microns and, even when present as larger grains as in nuggets, these are often complex multimineral intergrowths. Therefore, the PGM must be examined by microscopic techniques and, because all named PGM are opaque, they are suitable for microscopic study by reflected light. Special techniques for concentrating PGM and preparing suitable polished sections are detailed in Chapter 5. Another characteristic of the PGM is that the majority have very high reflectance at 589 nm, i.e., over 450Jo, but they range from about 38 to 74%. In contrast, micro-indentation hardness has a wider range from - 60 to - 3,000 kg I mm, and the PGM range from brittle to malleable.The small grain-size of PGM imposes certain limitations, or complications, on the usual mineralogical determinative methods of reflectance, micro-indentation hardness and X-ray diffraction. In addition, certain combinations of elements in some PGM render electron-probe analyses difficult. The usefulness and shortcoming of these methods, as applied specifically to the PGM, are discussed in the following sections. These are not, however, meant to be exhaustive descriptions of the techniques, which are fully described in other texts.6.1.2. Micro-Indentation HardnessDetermination of the Vickers Hardness Number (VHN) is discussed in detail in recent publications, such as Bowie and Simpson (1977) and Craig and Vaughan (1981). In addition, the recommendations of the Commission on Ore Microscopy (COM) of the International Mineralogical Association (IMA) are given by Criddle (1980). The usual small grain-size of the PGM, however, precludes the widespread use of this technique and very few PGM have, in fact, had their VHN determined at the COM-recommended standard load of 100 gf (cf. Cabri, 1981b, in Chapter 7). Examination of VHN data reported in the literature reveals that the few PGM whose microindentation hardness has been measured have incomplete VHN data, measured with loads other than 100 gf (Chapter 7). The small grain-size may also result in unreliable VHN data because, even though the correct load may have been applied, a thin grain will give erroneous data due to the matrix, or the grain may even shatter or pop out of the section. On the other hand, micro-indentations may give useful qualitative diagnostic clues. Moncheite, for example, shows fractures near the indentation (Chapter 7, Plate 1). In other cases, intergrown PGM produce different-sized indentations: e.g., froodite-michenerite-gold in Cabri (1972); isoferroplatinumtulameenite in Cabri et al. (1973); michenerite-moncheite in Cabri and Laflamme (1976) and Chapter 7, Plate 1; altaitemichenerite- testibiopalladite in Hudson eta/. (1978) and Plate 1, Chapter 7."

Jan 1, 1979

By Marcio Luis S. Godoy

The Salobo Project will be the first Vale operation to use an HPGR mill to process copper-gold ore. The mine is located in Para state, southeast of the Amazon region in Brazil. The circuit was designed to treat 12 million metric tons per year of finely disseminated sulphide ore with high hardness. The comminution circuit comprises a gyratory primary crusher, secondary crushing utilizing two cone crushers, two 2 x 1.5 m HPGR operating in closed configuration with 6 mm screens, followed by two 26 x 40 ft ball mills. The concentration circuit consists of two rougher flotation stages using mechanical cells, regrinding with vertical mills, three cleaner stages with columns and one cleaner scavenger stage in mechanical cells. The concentrate is dewatered, filtered and transported by trucks and train to the port, to be exported. The circuit was designed on the basis of data obtained from a comprehensive laboratory and pilot plant campaign. The ore variability was assessed through simulation using data from a drilling core characterization program. The start-up of the industrial plant is planned for 2011. This paper describes the main aspects of circuit design, as well as information related to the beginning of the project construction.

May 1, 2010

By J. Jerome MacDonald, Stephen B. Flewelling

"In the base metals industry of today, operations required to continuously improve productivity and reduce unit production costs. Consistent with these goals is the improvement of the muck haulage cycle from open stopes with the No. 12 Mine.Existing haulage from open stopes occurs with LHD units experience at Brunswick indicates that LHD units have a higher unit cost per tonne mucked than loader-truck combinations when the haulage exceeds approximately 150 m.The reintroduction of open stoping at Brunswick made existing loader-truck combinations unsuitable. It was recognized that application of recent continuous loading technology could potentially result in significant unit cost savings and productivity increases.A review of the technology resulted in the testing of the Voest Alpine AL60 loader in the open stopes located on the 1000m Le vel. Testing began in January 1988 and finished in late November 1988. The test will provide experience as well as quantified production and maintenenace parameters f or the purpose of quantifying production unit costs and system productivity, ultimately resulting in a decision to further utilize or not utilize the loader as a primarymucking unit at Brunswick .INTRODUCTIONBrunswick Mining and Smelting Corporation Ltd. produces approximately 10500 tonnes per day from the No. 12Mine located 35 km southwest of Bathurst, New Brunswick Mining is the largest (single mine) producer of zinc in the world having mined over 52 million tonnes since 1964. Many years of production still remain with proven and probable reserves in excess of 90 million tonnes. Reserves grade at an average of 3.65% Pb. 8.99070 Zn, 99g/mt Ag and 0.32% Cu . The operation employs 1446 people with approximately 800underground including operations and maintenance staff.In the No. 12 Mine two major mining methods are presently utilized . The primary method is Mechanized Cut and Fill (MCF) accounting for approximately 6500 tonnes per day from four major areas. The remaining 4000 tonnes per day is produced from open stopes with the majority of 2800 tonnes per day being produced by the 1000 level.The 1000Level contains 30 million tonnes segmented into open stope blocks 30 m high, 15m and 30 m on strike , with a transverse width of 10m to 50 m (Fig. I). Stopes are organized on a primary secondary stope arrangement along strike. Primary stopes are undercut and overcut full size with the back fully cablebolted. All stope and lateral development is driven 4.0 m high. All stopes to date are flat bottom (Fig. 2). Primary stopes are filled with cemented rock- fill , secondaries with conventional rockfill, Haulage from the stopes is primarily with 8-yard LHD units ; mucking is approximately 50% conventional and 50% remote. Haul distance to date has averaged approximately 150m with current stope haul distances of approximately 300m. Haulage is presently to a small jaw crusher situated on the 1000 Level. From August 1989on, haulage will be to a set of ore passes feeding to a large gyratory crusher situated on the 1200 Level. Start up of the gyratory crusher corresponds to an increase in tonnage from 1000 Level to 4100 tonnes per day."

Jan 1, 1989

By Werner Unland, Nick Holl

"The paper presents the engineering design and experience gained so far with a dewatering system for an open-pit uranium mine planned at Key Lake in Northern Saskatchewan.The results of hydrogeological investigations preceding engineering exhibit an extensive unconfined overburden aquifer hydraulically connected with the underlying Athabasca Formation and basement rocks, both of relatively low hydraulic conductivity. The overburden aquifer is embedded in a bedrock trough, with the deepest depression between the planned pits. The hydrogeological data were used in a numerical dewatering model simulating groundwater flow atdifferent stages of the pit development.Based on the model results, the engineering design had to provide for different pumping rates, varying between 1.0 and 0.21 ms/sec. This problem was solved by using a double line pressure system. The design concept for the complete peripheral discharge system and the well design used for 26dewatering wells are discussed.Experience with reverse-circulation techniques applied for the construction of the dewatering wells is presented. Theoretical and practical considerations which led to the constructionof wells of different diameters are discussed.The design of the in-pit dewatering system provides for seepage ditches, horizontal drains, pit-bottom sumps and inpit dewatering wells where required."

Jan 1, 1980

By Eddy Dénommé, Deni Villeneuve

"Niobec mine, a producer of pyrochlore concentrates since 1976, became a producer of ferroniobium in 1994 and achieved accreditation to the ISO 9002 standard in 1995. The goal of ISO 9002 is to ensure that the products supplied to clients regularly meet their specifications, through explicit work standards and procedures throughout the production process, from deposit appraisal to ferroniobium production.A key element of ISO 9002 implementation at Niobec consists of the quality control procedures applied to the raw materials: the ore fed to the mill and the pyrochlore concentrate fed to the reduction plant. These controls extend from exploration, deposit appraisal, mine planning and reserves estimation, mining, mineral processing and, finally, ferroniobium production. The implementation of ISO 9002 has allowed more efficient control of the quality of the final product sold to clients. It requires interactive team work, the role of the geologist being to relate all information pertaining to raw material and product quality to the geological framework of the deposits."

Jan 1, 1997