Search Documents

By Reed M. E, Cloutt B

Particulate samples were taken from the gas space in the settler of the Kalgoorlie nickel smelter using a vertical sampling probe and a specially designed isokinetic sampling probe which also quenched the samples. The vertical sampler was found to give unrepresentative samples. Suction thermocouple measurements of the gas temperature were also made. Using the isokinetic probe samples were taken at four points ranging from near the base of the reaction shaft to the base of the uptake at depths up to 1.5 m into the settler. Dust loadings and the sizing of the samples were determined. These parameters were found to be most affected by sample position and depth. The dust loading decreased along the settler but increased with depth. The loadings varied from zero near the roof to several hundred g Nm 3 near the slag. The dust also became coarser with increasing depth into the settler. Examination of the samples showed them to consist of spherical particles the largest of which were about 500 microns in diameter. The dust was mainly composed of mixed iron/nickel oxides with a little sulphide.

Jan 1, 1991

By A Takahashi, Y Uchisawa, M Hayashi, T Watanabe, M Susa

Owing to the deterioration of iron ore, the Al2O3 concentration in iron ore increases, and thus it is important to investigate the effect of increment in Al2O3 concentration on the microstructures of iron ore sinters. During the sintering process, a melt is present in the sinter for only a few minutes, and therefore the microstructure of the sinter doesn’t reach thermodynamic equilibrium. Nevertheless, the formation process of the microstructures can be interpreted and predicted to some extent from the equilibrium phase diagram. This study investigated the liquidus isotherm in the CaO-SiO2-Fe2O3- 5 mass% Al2O3 system at 1240°C in air and the phase equilibria of silico-ferrite of calcium and aluminium (denoted by SFCA) and SFCA-I by XRD (X-ray diffraction analysis) and electron probe micro analyzer (EPMA). The following results were obtained: 1. The ferrite melt region with a high Fe2O3 concentration shifts to the lower Fe2O3 side than the liquidus isotherm in the CaO-SiO2-Fe2O3 system. 2. The compositional region of SFCA extends in the CaOꞏ3Fe2O3-4CaOꞏ3SiO2 direction than the silico-ferrite of calcium (denoted by SFC) composition region with a 0 mass% Al2O3. 3. SFCA-I is observed in the present system, which suggests that the increment in the Al2O3 concentration contributes to the stability of SFCA-I. These results imply that an increment in Al2O3 concentration in iron ore leads to a decrement in the volume fraction of the bonding phase and that the fraction of the SFCA phase increases, and those of 2CaOꞏSiO2 and slag phases decrease in the bonging phase. The SFCA-I phase is also precipitated from the slag with an Al2O3 concentration around 5 mass%.

Jun 19, 2024

By E S. Weiss, S P. Harteis

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) has conducted full-scale explosion experiments, to evaluate the strength characteristics of various seal designs, used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests conducted within the multiple entry section of PRLÆs Lake Lynn Experimental Mine (LLEM) is currently the only accepted test method used by the Mine Safety and Health Administration (MSHA), for deeming a seal design suitable for use in American mines. These explosion tests are labour intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. The PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in situ testing of seals in an operating mine. Two chambers within LLEM and one within PRLÆs Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from these chamber tests compare favourably with those from the large-scale explosion tests in the multiple entries. In addition to testing seal designs at the required 20 psi static pressure level, the chamber test approach also allows for the determination of the sealÆs ultimate design strength. Size-scaling relationships for predicting the strength of seal designs as a function of entry size are also presented.

Jan 1, 2005

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By D Morgan, D Sato, B Lumsden, S Senanayake

Laboratory flotation tests on fresh cyclone overflow samples are a useful tool to troubleshoot and indeed to improve plant performance; however, reproducibility between laboratory flotation test and plant performance is important for interpretation of the laboratory tests and hence their usefulness. Chemical reproducibility can be achieved with the addition of the required reagents; however, reproducing the physics of forces and energy in a 5 L cell compared to a 50 000 L plant cell or a 500 000 L plant cell is not generally studied or discussed. For some tests such as collector evaluation the physics of the flotation process may not be critical, but for some evaluations in the laboratory, it can be important.All flotation plants suffer from losses of valuable <20 µm mineral. Selective mineral aggregation has long been recommended to improve the poor flotation recovery of <20 µm sulfide minerals; however, successfully testing any type of selective sulfide mineral aggregation’s effect on flotation recovery in the laboratory on practical plant samples requires reproducing plant cell physics. The energy input per litre and the forces in a laboratory cell are vastly different to a plant cell. Reproducibility between laboratory and plant tests requires that these differences be minimised. The physics of the laboratory flotation cell is particularly important when fine mineral aggregation tests are carried out.This paper outlines a modified laboratory aggregation and flotation method that closely reproduces plant performance in a laboratory test.CITATION:Sato, D, Lumsden, B, Senanayake, S and Morgan, D, 2014. Development of a laboratory flotation method to test plant mineral aggregation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D McLaughlin

This paper points to the timely importance of commencing a centrally recognised perpetual collection of mineral specimens in the Northern Territory which has as one of its objectives the collection and preservation of Northern Territory minerals of scientific, educational and heritage value. Currently in the Northern Territory there is no government department or institution that has a resourced coordinated state-wide objective to collect and document collectable mineral specimens. Specimens held in storage by the Department of Mines and Energy and the Museum and Art Galleries of the NT are not catalogued and owe their existence to fortuitous circumstances, not as a result of a planned systematic scientific approach to mineralogy. Northern Territory mineral species and unique specimens have and will continue to be driven to extinction while no central and active, recognised repository exists. This situation persists despite the fact mineral production is the Territory's largest income earner. The paper presents the arguments that hopefully will assist decision-makers to commence development of a state mineral collection lodged within an appropriate institution in the Northern Territory.

Jan 1, 1994

By J Zhou, L Crompton, K P. Galvin, J L. Sutherland, C P. Lowes, C Bezuidenhout, J Bijzet

Platinum Group Metal (PGM) bearing ores from the Upper Group 2 (UG2) reef often contain significant concentrations of chromite which can potentially be upgraded to produce a saleable product. A common approach is to implement gravity separation on the PGM flotation circuit tailings. However, where the particle size range of interest is broad and the lower size limit ultra-fine, the challenge is how to maximise the recovery at a saleable product grade without compromising throughput. This study was concerned with the performance of a REFLUX™ Classifier for beneficiation of a PGM bearing chromite ore and the benefits of size classification. The sample had a nominal top size of 0.5 mm and was processed over the complete size range and in two discrete size classes following classification at 106 µm. The primary goal was to produce a concentrate exceeding 40 wt. per cent Cr2O3, ideally approaching 42 wt. per cent Cr2O3, with minimal PGM losses above 106 µm. A major challenge was to process at the required solids throughput in a single stage with the feed pulp density constrained to a nominal upper limit of 30 wt. per cent solids. It was found that varying the controller density set point of the REFLUX™ Classifier produced strong control of the product grade. Products as high as 41.1 wt. per cent Cr2O3 were produced at 78.6 per cent recovery for the +106 µm material, while in the −106 µm portion the product grade was as high as 41.4 wt. per cent Cr2O3 at 83.2 per cent recovery. Processing the feed in discrete size classes enabled the volumetric feed and fluidisation rates to be optimised for a given application; hence, superior performance was achieved at the finer sizes. This work has demonstrated the value in considering feed preparation as well as technology selection in developing a robust process solution.

Aug 24, 2022

By K R. Vining, T E. Norgate

A study was carried out to compare the environmental impacts of the two major iron ore agglomeration processes, sintering and pelletising, using life cycle assessment (LCA) methodology. The following agglomeration processing routes, with the fuel options shown, were investigated:sintering with combined natural gas/coke breeze or charcoal as fuel, grate-kiln pelletising with combined natural gas/coke breeze as fuel, and straight-grate pelletising with combined natural gas/coke breeze as fuel. Inventory data for each process derived from the literature, and in some instances supplemented by additional simulations and calculations, were used in the study and the environmental impact categories considered were gross energy requirement (GER), global warming potential (GWP) and acidification potential (AP). The results of the study showed that the GER, GWP and AP for a sinter plant are higher than those for a pellet plant for the same amount of metallic iron in the agglomerated products. These results are partly due to higher consumption of solid fuel and flux in the sintering process. However, it should be pointed out that the study only compared substantially fluxed sinters with acid pellets that may require additional flux (and hence potentially more greenhouse gases emissions) to be a balanced blast furnace feedstock. Extending the LCA to the blast furnace process stage was beyond the scope of the current study. Within the sinter plant, the sintering stage itself is the largest contributor to the GER, GWP and AP. In the case of pellet plant, the pellet induration stage is the largest contributor to the various environmental impacts. The GER and GWP of a straight-grate pellet plant are marginally higher than those of a grate-kiln pellet plant due to the higher electrical power required by the straight grate system. The substitution of coke breeze with charcoal in the sintering process results in an increase in GER but a decrease in GWP. However, a substantial proportion of the GER is derived from renewable sources (wood), resulting in a decrease in the non-renewable components of this environmental impact. Given the source of the inventory data and the assumptions and approximations made in carrying out the LCAs, it is emphasised that the results presented in this paper should be considered as indicative rather than as definitive results for the two iron ore agglomeration processing routes considered.

Jan 1, 2006

By J Joy, D Griffiths, A Bye, G V. Kizil

Poor standards of electrical installation and maintenance continue to contribute to electrical related fatalities and injury risk in the mining industry. Electrical isolation has the potential to initiate major unwanted events (MUEs) and as such requires thorough analysis to demonstrate adequate management. There have been 719 incidents related to accidental contact with electricity over the past five years in the Queensland mining industry (Queensland Government DME, 2012a, 2012b) with the last fatality being recorded in 1997 (MESA, 2012).A project funded by the Australian Coal Association Research Program (ACARP) has developed a form of a safety case using the four-layered æCoal Mine Safety Regime (CMSR)Æ approach. The CMSR is transparent and robust as it includes full site risk assessment and special issues risk assessment to be demonstrated as part of the process.The practical application of the CMSR has been demonstrated using a longwall mining case study site, where a unique 11 kV armoured face conveyor (AFC) is in operation. The case study has involved progressive application of the requirements of each layer of the CMSR (see Figure 1) to high voltage (HV) electrical isolation related issues. The project has specifically concentrated on understanding and analysing two high priority MUEs, electric shock and unplanned movement of equipment, through Layer 1 analysis. These two MUEs are an important part of the project as they have demonstrated the steps that may be taken to satisfy the risk management processes at Layer 1 of the CMSR and have contributed to resolving issues at the other three layers of the CMSR.The analysis of HV electrical isolation has been used as an exemplar to demonstrate the CMSR process and its practical application. The CMSR is applicable to major/principal hazards management as identified by the New South Wales and Queensland jurisdictions.This paper provides an overview of the development of a form of safety case using the CMSR and introduces the case study application for HV electrical isolation risk management at underground coal mines focusing on the major unwanted event of electric shock.This project provides the mining industry with a documented, publicly accessible, form of safety case using the CMSR approach for the first time.CITATION:Kizil, G V, Griffiths, D, Bye, A and Joy, J, 2012. Using a coal mine safety regime approach to the management of high-voltage electrical isolation, in Proceedings International Mine Management 2012, pp 59-74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By M I. Pownceby, S Bhargava, F Charalambous, S McMaster, R Ram, J Tardio

"A key component of any geometallurgical investigation involves being able to predict element or mineral recoveries from simplified input data such as bulk chemistry and/or mineralogy. This relies on the metallurgist having access to accurate information regarding the chemistry of the ore and gangue minerals as well as the likely impact on processing/extraction caused by the impurities (present either as gangue or as substitutional impurities). In this study the chemical properties of two commercially important uranium minerals, brannerite (U4+Ti2O6), and uraninite (U4+O2), were characterised using X-ray diffraction (XRD), scanning electron microscopy (SEM), and electron probe microanalysis (EPMA). Significant levels of impurities were present in both samples with the uranium minerals deviating significantly from their ideal chemical formulae. Differences in chemistry were due to: cationic substitution decay of the uranium isotopes into radiogenic lead and other daughter products mixed uranium oxidation states post-depositional alteration.As well, the brannerite sample showed evidence of significant radiation-induced metamictisation. Leach tests to measure the ease of extraction of uranium from both samples were conducted over a wide range of conditions (temperature, acid concentration and oxidant concentration). For uraninite, the lower U dissolution rates observed in the natural sample compared to a synthetic UO2 sample were directly attributed to the presence of impurities. For brannerite, significant metamictisation of the natural sample led to enhanced U extraction rates compared to a heat treated fully crystalline sample. This study highlights the importance of detailed mineralogical characterisation studies in any uranium process mineralogy investigation as the compositional, textural and microstructural aspects of the main uranium phases present will likely play an important role in any process to extract uranium.CITATION:Ram, R, Charalambous, F, McMaster, S, Pownceby, M I, Tardio, J and Bhargava, S, 2013. Chemical and microstructural characterisation studies on naturally occurring uranium minerals - implications for processing, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 325-334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By D Flint, O Rindriatmoko

PT FreeportÆs Deep Ore Zone (DOZ) Mine is the latest block cave mine within the East Ertsberg Skarn System (EESS).Issues with undercutting and stress concentrations at the extraction level were experienced, leading to reduced pillar strength.The extraction level-related issues became more pronounced, leading to local panel drift collapse, in an area that was over 100 per cent extraction. A review of ground conditions, panel collapse descriptions, and factors contributing to panel collapse are presented in this paper.

Jan 1, 2005

By S McKnight, L Koroznikova, S Hall

Mineral sands represent an important new resource being developed in the Murray Basin, including parts of western Victoria. This paper will outline a simple methodology for mineral sands characterisation, developed as part of the AMIRA-managed project P777 æThe Development of Heavy Suspension Techniques for High Density Separations (Replacement of ClericiÆs Solution)Æ. This project is currently sponsored by three multinational mining companies (De Beers Consolidated Mines, Iluka Resources Limited and Rio Tinto Limited) and is developing an innovative laboratory mineral characterisation procedure that will allow the replacement of the currently employed highly-toxic chemicals.Mineral sand resources almost always contain more than one valuable (and relatively heavy) mineral. Titanium minerals are found with a large range of titanium contents, giving rise to density variation and often subjective mineralogical descriptions. Companies tend to rely on laboratory heavy liquid separation in the evaluation of samples arising from exploration, mining or metallurgical processes. Unfortunately, there are only a limited number of high density (æheavyÆ) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. However, beyond this value currently only organic liquids can be used. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used; however, this presents significant health and safety hazards. Mixtures of thallium formate and thallium malonate were found in the early 1900s by Clerici to provide liquids having specific gravities between 4.0 and 5.0, hence æClericiÆs solutionÆ. For the characterisation of the heavy components of mineral sand deposits (eg anatase sg 3.9, rutile sg 4.2, ilmenite sg 4.4 û 4.7 and zircon sg 4.6 û 4.8) there is currently no heavy liquid alternative to ClericiÆs solution. ClericiÆs solution is highly toxic and testing is now conducted by very few laboratories worldwide with costs reflecting the chemical costs (though extensive efforts are made to recover and reuse the liquid, plus the requirement of its removal from the mineral samples), the infrastructure costs and health and safety regimes (eg blood testing of exposed staff, inventory management). A simple laboratory technique of density fractionation is being developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions, that can replace ClericiÆs solution in the evaluation of fine mineral sands samples (eg -250+150 microns). The developing methodology that can achieve low-cost, low-toxic separations at relative densities above 5.0 will be outlined and the comparison of results with ClericiÆs solution presented.

Jan 1, 2006

By M Zengerer

The Basil Cu/Co deposit comprises a 26.5 Mt Inferred Resource of copper and cobalt, grading 0.57?per cent Cu and 0.05 per cent Co. It lies in the Harts Range, Central Australia, within the Riddock Amphibolite of the Irindina Province. Analysis of drilling within the mineralised zone of the deposit determined a spatial association between pyrrhotite with high magnetic susceptibility and chalcopyrite, following a strong magnetic trend as determined from airborne geophysics. A study was commissioned to examine if geophysical inversion could predict the distribution of sulfide mineralisation based on pyrrhotite from drill hole intersections, as well as predicting further mineralisation at depth or in the vicinity of the deposit. Petrophysical and geostatistical analysis of drilling susceptibility and mineralisation provided a basis of property distribution inside the model. This was followed by 3D geological modelling of mineralisation based on domain kriging of drill hole susceptibility sensitivity testing of signal to source depth, and distribution was performed using 3D forward modelling. Stochastic inversion generated alternative 3D geological models, which were tested for behaviour and adherence to observed drilling data and geostatistical limitations using GeoModeller software. Predicted mineralisation distribution was compared with conventional geostatistical modelling and found to be in agreement in planar behaviour but exhibiting possibly isoclinally folded trends, with reliability increasing closer to the surface. Predictions of mineralisation at greater depth and beneath weaker anomalies were more diffuse due to small model cell size having limited influence on the signal at depth.The Blackbush uranium deposit comprises a 64.5 Mt Inferred Resource, grading 230 ppm U in the Pirie Basin south of Whyalla, South Australia. It directly overlies the radiogenic Samphire Granite and is considered a tertiary unconformity deposit. Sensitivity modelling was performed using high-resolution ground gravity to see if a deposit signature could be detected using gravity. This required 3D implicit modelling of the geology and mineralisation from drill hole data and characterisation of an associated physical property model using domain kriging in GeoModeller. Density models relied on exploiting an observed relationship between logged density and measured uranium oxide percentage. The residual gravity response of the background geology model identified the location of the uranium deposit. Stochastic inversion of the litho/property 3D model has refined the known distribution of uranium from drilling and provided structural insights into the deposit.These projects have become excellent case studies for exploiting the relationship between mineralisation and potential fields and for testing the applicability of using domain kriging of properties determined from drilling to build robust 3D geological models for stochastic geophysical inversion, leading to robust methods for exploration targeting and mineral deposit prediction.CITATION:Zengerer, M, 2014. Use of geostatistically-constrained potential field inversion and downhole drilling to predict distribution of sulfide and uranium mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 281–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By R N. Lamb, A N. Buckley

Experiments have been carried out to establish whether time-of-flight secondary ion mass spectrometry (ToF-SIMS) is able to differentiate monolayer and multilayer coverage of thiol collectors on sulfide minerals. The systems investigated were those for which x-ray photoelectron spectroscopy is able to provide an independent determination of the extent of coverage, and included diethyldithiophosphate (DTP) and 2-mercaptobenzothiazole (MBT) on chalcocite, DTP on Ag2+MS prepared by sulfidising metallic silver, and isobutyl xanthate (BX) and MBT on galena. For monolayer adsorption of MBT on chalcocite, peaks from MBTû but not Cu(MBT)û ions were evident. For multilayer coverage, Cu(MBT)2û ions were clearly present, notwithstanding the fact that other data had identified the principal multilayer species as Cu(MBT). For adsorbed DTP on copper and silver sulfides, DTPû and metal(DTP)Hû peaks were observed for monolayer and multilayer coverage. Although the multilayer species was expected to be predominantly metal(DTP), metal(DTP)2û ions were evident for multilayer (but not monolayer) coverage. For the PbS/BX system, intact Pb(BX)2 or Pb(OH)BX ions were not detected for multilayer coverage, although Pb-containing ions heavier than PbBX were. Indeed, for all the systems studied, ToF-SIMS was able to differentiate monolayer from multilayer coverage. In general, however, the SIMS evidence alone might not be sufficiently definitive to effect the differentiation. In the case of collector adsorption on copper and silver sulfides, if the multilayer species detected had been the metal monothiolate only, and had not involved the formation of some metal dithiolate, then ToF-SIMS might not have been able to provide an unequivocal differentiation of the two coverage conditions.

Jan 1, 2005

By D K. Weatherley, A N. Mainza, I Govender, L M. Tavares, M S. Powell

It is understood that rocks do not instantaneously transport along a grinding mill and are consequently not perfectly mixed, but this is conveniently overlooked in mill modelling. A lack of understanding of the transport phenomenon and the difficulty of modelling realistic transport in a complex tumbling system, contribute to this. Visual observation of segregation in AG and SAG mills and measured lag time of mill response to changes in feed provide evidence of the influence of axial transport within mills. Incorporating this lag in dynamic models should underpin dynamic simulation of milling circuits for design and for model-based control. Limitations and errors in predicting the influence of increased power via mill length versus diameter, inability to predict pebble production, and a lack of the differential in residence time across rock sizes and competences, all contribute to inadequate design prediction that can be especially acute for large Autogenous mills. Examples of dramatically under – and overloaded pebble regrind circuits and the inability to predict pebble load in AG milling discouraging the application of this energy-efficient option, point to the need for predictive modelling of breakage by competence linked to transport through and out of mills. Incorporating progress in granular flow and mixing, coupled to computational advances enable models to be based on complex breakage and transport models at high spatial resolution. This allows mechanistic models to simulate thousands of times faster than real time, opening the door to more accurate mill design, including dynamics in process simulation and to live simulation for process control – all with advanced mechanistic models. The value of grasping this opportunity is not easily refuted.

Aug 24, 2022

By Richards RG, Cross MS

The development of alluvial mining, processing systems and associated gravity separation technology over the last 30 years is largely linked to the mineral sands industry. Attention has been focussed on Australia in these areas of mineral resource development and technological Advancement.

Jan 1, 1986

By J Herrmann, J Richards, B Hutchison

An extensive trial of laser-based survey and monitoring systems at Hillgrove Resources Kanmantoo Copper Mine in the Adelaide Hills, South Australia, has proved the capabilities of the system in monitoring rock movements on open pit walls. Initially, the trial involved deploying a Maptek I-Site 8820 laser scanner and the proof-of-concept Maptek Sentry software in the Nugent Pit to monitor ductile rock movements located up to 260 m away. The system was proven to be capable of monitoring various rock movements from 1.5 tonne rockfalls up to a 40 m high toppling wall failure. Data collected from smaller rockfalls was used to help build a database for Hillgrove’s rockfall management program. As part of the trial, the laser scanner was deployed to monitor a ramp movement event, as well as the toppling failure, adjacent to an IBIS slope stability radar. Both devices monitored the slump and the slowly developing toppling movements, with similar results. Although the radar was used as the successful ‘critical alarm’ device for the toppling failure, post-failure analysis showed the laser-based system to be capable of performing a similar role in the ductile rock regime; albeit over much shorter distances than the radar capability. A second laser scanner was deployed to monitor Kanmantoo’s Emily Pit in early December 2014, where it successfully provided critical alarm warnings for a block topple event. Sentry software, which takes advantage of Maptek I-Site 3D spatial imaging technology, was first released in November 2014 to meet industry demand for a cost effective, flexible system to detect movement. Sentry has now been re-launched as a fully transportable monitoring system. Deployed in a custom trailer, the system offers a power and communications module, cellular and Wi-Fi networking and a stable bollard for the I-Site laser scanner and Sentry software. This paper will present rock wall movement data from the Sentry trial and a subsequent two years of monitoring of the open pit walls at the Kanmantoo Copper Mine, at distances out to 750m. In addition, examples of remote geological mapping and small rockfall detection, using the laser scans, will be described. The Sentry system has proven to be beneficial for the continual improvement of slope monitoring and risk management at hard rock mines. CITATION:Hutchison, B, Richards, J, Richards, J and Herrmann, J, 2018. Mine rockfall and rock wall failures – proven digital laser-based approach for monitoring slopes at the Kanmantoo Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 463–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Saghaeian, V Sheikhzadeh, R Hejazi

Mining dilution is one of the most important factors affecting the economy of mining projects. Instead of quantifying dilution in mining studies, it is common to assume a general dilution such as 5 per cent for massive deposits. Dilution increases the operating costs in the plant by increasing the tonnage of material to be milled. It prolongs the mine life by reducing plant’s effective capacity. It also reduces the feed grade. In most cases, lower feed grade means lower plant recovery. Dilution also increases the cut-off grade, which in turn reduces the overall ore utilisation of a mine. In this study has been investigated applying pre-concentration by dry magnetic separation for decreasing of dilution impact on reserve estimation and open pit design in low-grade iron ore mine. Based on the preliminary open pit design and assumption 3 per cent as dilution factor, the mineable ore in life-of-mine (measured + indicated) has been estimated with Fe = 25 per cent, SiO2 = 49.7 per cent. Based on the experimental test work on the ore, by dry low intensity magnetic separation of dry HPGR product grinding circuit, it is possible to remove diluted waste material and liberated gangue before concentrate plant, so that around 34 per cent rejected and Fe grade increase from 25 per cent to 33 per cent and by weight recovery 66 per cent. The results of the test work showed that this methodology could decrease largely the impact of dilution in the feed to the plant. It also slightly effect on the reducing of dilution factor impact for open pit design and optimisation and leads to increase the mineable tonnage in the low-grade magnetite iron ore mine.

Aug 24, 2022

By C Simpson, J Market

The process of sampling blasthole cones utilising personnel to manually shovel material into sample bags is a long-standing industry accepted process. However, this method has several drawbacks, including the safety issues around having personnel performing manual sampling in a harsh environment and the variability involved in getting a human to repeatedly get a ‘shovel full of dirt’, and make it always representative. Geophysical blasthole sampling, or utilising a Downhole Assaying Tool (DHAT) has been tested and has now begun implementation at many iron ore sites throughout the Pilbara region, Western Australia. This method uses a geophysical tool to capture data within blastholes, and together with a semi-autonomous logging platform to minimise risks around manual handling, delivers a multielement proxy-assay which can be utilised by the mine geology team to accurately domain the orebodies. Logistically, the combination of a specially designed tool and semi-autonomous truck are the way forward for a safer and more data-robust blasthole sampling practice. The method utilises a neutrongenerating geophysical tool and linked elemental spectroscopy sensor, which measures the response of the material surrounding an open hole. This delivers results at submetre intervals. These results are then utilised, similar to blasthole sample results, to map out areas within the blast pattern that are ‘ore’, ‘waste’, or ‘other suitable grade’. This paper outlines a project that has been in ‘proof of concept’ at selected Fortescue sites over the last few years with testing of these tools carried out on reverse circulation (RC), diamond drill and blastholes. The method is now being implemented at operational hematite mine sites. Fundamentally, the method adds more than enough value to justify its implementation. The aim is that these learnings will enable the greater industry to adapt, implement and improve their mining practices. Ultimately, the outcome will be greater value in mining for the industry by having a larger volume of good quality data to make reliable decisions on material movements, minimising ore-loss and dilution, and maximising the value of our current and future orebodies.

Nov 8, 2021

By C Hoffmann

Given that each year, 30–40 per cent of mining industry deaths are attributable to failures of vehicle interaction controls (EMESRT, 2023), the mining industry is now armed with a growing body of knowledge from EMESRT (Earth Moving Equipment Safety Round Table) and ICMM (International Council on Mining and Metals) global vehicle interaction initiatives over the past years, that enables mining companies, OEM’s and technology providers to work together to develop and implement more effective controls and drive the adoption of capable solutions. Leveraging 20 years of experience as a global technology provider of Proximity Detection System (PDS) and Collision Avoidance System (CAS) solutions for surface mining operations, Wabtec Digital Mine Technology shares key insights for ensuring the effective selection, implementation and integration of these technologies into existing mine site controls and mining operations for effectively reducing vehicle interaction risk enabling mines to drive towards ‘zero-harm’ objectives. Topics covered include: alignment with industry best practice for controlling vehicle interaction risk by EMESRT and ICMM, importance of the maturity of EMESRT levels 1–7 vehicle interaction (VI) control framework, managing expectations that PDS/CAS is a ‘silver bullet’, alignment with industry functional – performance – technical requirements, proximity detection versus collision avoidance, sensor performance and fusion and limitations, rules engine intelligence critical to mitigating nuisance alarms during normal operations, system health monitoring and reporting, human factors engineering and operator acceptance, implementation strategy, installation standards and quality control, change management program, training programs, reporting and data analytics with actionable insights and maintenance strategies. Insights will also be provided on the challenges moving from EMESRT levels 7 (operator awareness) and 8 (advisory controls) to level 9 (intervention controls) as it’s a journey not an out-of-box solution, the growing demand for coexistence of CAS and Autonomous Haulage Solutions (AHS), functional safety approach, value added systems integration and the applicability of new emerging technologies.

Apr 16, 2024