Search Documents

By D Kilkenny

This paper discusses the use of a mechanised shaft sinking machine Herrenknecht Vertical Shaft Sinking Machine (VSM) – to conduct the 93 m presink for the Wira Hoisting Shaft at the Prominent Hill Mine in South Australia. This technology has been widely used in the global construction industry, however, this was the first time it had been used in Australia and the second time in a mining application. The non-entry shaft sinking system eliminates risks associated with a traditional manual method and allows all shaft construction operation to take place from surface. The geology in the upper 100 m at the Prominent Hill mine is conducive to mechanical excavation, with expected rock strengths below 130 MPa. This enabled an alternative shaft construction methodology to be considered. The Herrenknecht VSM system was selected due to its extensive work history and demonstrated performance in similar ground conditions. In collaboration with the operations and design team, the shaft collar and surface configuration were modified to suit the requirements of the VSM, additional equipment, and loading jacks that support the pre-cast lining. Dedicated concrete moulds were designed in Germany and built in Italy. The concrete segments were cast in Adelaide and road freighted to site. This paper outlines each stage of the presink – refurbishment, transportation, logistics, establishment, operation and demobilisation. Selecting this shaft presink excavation methodology, delivered through positive collaboration and communication despite some challenges, shows the benefit to the mining industry of applying new technology and innovation to improve safety and productivity.

Mar 29, 2023

By D Baas, J Le, R Braun, R Chandramohan, K Hollis, G Lane

The Phu Kham Copper-Gold Operation (Phu Kham) is located in northern Laos, approximately 140 kilometres from the capital, Vientiane. The operation is a producing asset for Australian-based copper and gold producer, PanAust Limited (PanAust) and is operated by Lao-registered company, Phu Bia Mining Limited (Phu Bia Mining). PanAust holds a 90 % interest in Phu Bia Mining. The Government of Laos owns the remaining 10 %.The Phu Kham Operation has recently undergone a series of process improvements to treat the anticipated competent ores scheduled for 2017 and 2018. The operation’s comminution circuit, which comprises a semi-autogenous (SAG) mill and two ball mills, each with 13 megawatts (MW) of installed power, was expected to be SAG mill limited when treating competent basement rock. Ausenco Services Pty Ltd (Ausenco), was engaged to help optimise and enhance the productivity of the Phu Kham comminution circuit over an eight-month period. The work involved participating in and overseeing the redesign of the SAG mill liner systems and developing operational strategies for maximising throughput through to the end of mine life. Ausenco’s comminution optimisation tool, Ausgrind, was used to benchmark and analyse plant data with empirical models, predict circuit performance for varying ore characteristics and evaluate liner wear and predict the life for varying operating parameters. Variances between the actual and the predicted values were assessed in detail to identify missed opportunities, and guiding operating parameters were redefined to maximise throughput and productivity. In combination with the redesigned liner system, optimised process controls for varying ore competencies, and improved operational practices and troubleshooting strategies, increased Phu Kham overall production, exceeding the milling capacity when treating competent ores. CITATION:Chandramohan, R, Braun, R, Lane, G, Hollis, K, Le, J and Baas, D, 2018. SAG mill optimisation and increasing throughput at the Phu Kham Copper-Gold Operation – a success story, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 113–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L Schürmann, R Kendall

Social licence to operate is becoming part of a mining company’s DNA in the same way as health and safety. Consequently, mining companies are receiving increasing pressure from their shareholders to ensure that they add enduring value to the local communities in which they operate. Apart from the shareholders, a company has responsibility to suppliers, customers, employees, the government and the community, which means under the social responsibility model they must be accountable to the other stakeholders. External and internal challenges in mining are increasing the difficulty and complexity of mines to operate. The external mining environment has a big impact on mining operations and is driving matters such as the focus on safety, responsible mining and resource management, sustainability issues, profitability and productivity. Considering this, it is expected that the widespread implementation of Environmental, Social and Governance (ESG) related practices across the mining industry in the next ten years will increase, not just for the big players but for juniors as well. Companies, investors, governments and insurers who fail to act on ESG matters are to likely face greater risks. Demonstrating leadership in ESG will ultimately become a differentiating factor and market participants have much to gain from embracing ESG stewardship as part of their competitive advantage. Stock Exchanges have an important role to play in advancing sustainability in the capital markets. It is for this reason that the Sustainable Stock Exchanges (SSE) initiative was founded to serve as a global platform for exploring how exchanges can enhance performance on ESG issues and encourage sustainable investment. The SSE initiative provides an effective platform for dialogue between the United Nations, stock exchanges, investors, companies and regulators in the mining industry. The paper will explain why ESG reporting is crucial for the survival of a mining company and how the lack of transparency could be detrimental to its public image and shareholder relations. The paper will also identify bodies that regulate ESG reporting, as well as the available tools that provide guidelines on reporting ESG matters. Key ESG reporting parameters (at a global scale) will also be highlighted.

Jun 22, 2022

By F Weir, B Estrada

The impact of seismic loading on open pit slope stability in Australia is often only considered where the slopes are located adjacent to tailings facilities or other major infrastructure. The debate regarding application of seismic loading in open pit design in Australia is usually founded on limited reporting on significant damage of open pit operations during earthquakes, the common perception that earthquakes do not occur in Australia or that they are unlikely to occur during the mine life of the mine. It is frequently overlooked that pit slopes that have withstood strong earthquakes in highly active seismic regions are often designed under strict seismic guidelines. This paper discusses the factors that impact earthquake performance of open mine slopes. These factors include topography, slope geometry, rock material and mass properties, water management and intrinsic pit design. Further, the paper presents insights into the characteristics of earthquake activity in Australia such as magnitude distribution, earthquake depths, areas prone of earthquake activity and general seismic hazard that are relevant to pit design. Guidelines are provided on the conditions and circumstances under which earthquake design in open pit mining should be considered. In addition, this paper provides recommendation on the applicable methods for assessment of the impacts of earthquake loading on pit slope stability.

Jun 22, 2022

By X Feng, X Zhang, W Sun, Y Zhe, K Hou, B Zhao, H Liu

Pulang Copper Mine, being China's largest newly built mine using block caving, boasts an annual production capacity of 12.5 million tons. Production level and roadway stability hold the key to the successful application of block caving. However, with Tong Kuangyu being the only mine in China which has applied such a method, we currently lack relevant experience in the successful application of the method. This paper has studied the influence of different rock mass zonings, fault thickness, fault dip angles, on-site construction quality on the production level, roadway stability of block caving through numerical simulation and analysed the roadway stability in different kinds of support solutions so as to ensure the successful application of block caving in Pulang Copper Mine. The results have shown that the existing support method in Pulang Copper Mine can meet the requirement of roadway support in zone II and III, but could not satisfy the demand in terms of support strength in the relatively fragmented zone I area. When roadway passes through the fault, the deformation of surrounding rock and plastic zone of roadway will gradually decrease with the increase of fault dip angle; the deformation of surrounding rock and plastic zone of roadway will gradually increase with the increase of fault thickness. An ideal support effect can be achieved through the joint support of grouting and bolting when roadway passes through the fault. In the measured model of on-site construction, there is stress concentration in the intersection between the access and transverse drift of ore removal. Therefore, the stability of the roadway can be improved by improving the construction quality. CITATION:Sun, W, Hou, K, Zhang, X, Feng, X, Liu, H, Zhe, Y and Zhao, B, 2018. Research on supporting technology for production level roadways of block caving in Pulang Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 95–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Tiihonen, J OÆCallaghan, T Haakana

Outotec is today capable of providing technologies, process equipment and engineering for the construction of pressure oxidation leaching (POX) plants in any location in the world. Outotec works with customers from mine to pure metal, participating in plant design from the process development phase (including test work execution/supervision) to plant commissioning and operations. Either key equipment technology packages with basic engineering or entire POX plants can be supplied.The addition of pressure oxidation equipment to OutotecÆs product portfolio adds to and complements already existing significant experience in general hydrometallurgical process and proprietary equipment design and supply.In addition to providing key pressure vessels, piping and valves to a POX plant, Outotec can offer an enhanced and proven autoclave agitation system that maximises oxygen mass transfer and utilisation. Novel energy and water recovery technology can also be tailored to a customerÆs specific needs. Importantly Outotec owns and operates extensive test work facilities and can provide test work to ensure the optimum POX flow sheet and materials of construction. Outotec ensures that best available technology (BAT) concepts are used in POX design to improve the availability of the process and minimise unpredicted shutdowns.CITATION:Tiihonen, J, Haakana, T and OÆCallaghan, J, 2013. Outotec pressure oxidation - more out of sulfide ore, in Proceedings World Gold 2013 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Eggleton R. A, Taylor G

As the search for major orebodies continues, the regolith dominated areas of the Broken Hill region remain one of the major exploration frontiers. The past exploration philosophies emphasising bedrock related characteristics have been limited in their ability to effectively explore in the regolith dominated areas, that are a feature of most of the Broken Hill region (Figure 1). If mineral exploration is to be more effective across all of the Broken Hill region, particularly in the regolith dominated areas, an appreciation and increased understanding of the regolith and landscape features are a necessity. Ironically, there have been very few studies of the regional regolith and landscape features of this region. Owing to the previous lack of an established regolith-landform framework, this study initially concentrated on the general characterisation and variation in regolith types corresponding to the area of the Broken Hill Block, within NSW (Willis, 1989; Stevens, 1986). The approach has been to produce a regional regolith-landform map at 1:100 000 scale and conduct a complimentary program of regolith sampling and site descriptions. This was a basis to identify areas for more detailed regolith-landform mapping (1:25 000 scale) and for producing a regional stratigraphic framework and models for landscape and regolith evolution. This information can then be used to provide a basis for regional mineral exploration models and strategies. This paper highlights some of the regionally significant regolith-landform features and their general significance to mineral exploration. More detailed information on specific regolith-landform features and study sites may be found in Hill et al (1994; 1996; in press) and Hill (in prep).

Jan 1, 1997

By G M. Mudd

The growing popularity of platinum and platinum group metals (or PGMs, including palladium, rhodium and others) for a wide range of applications leads to some interesting issues for mining and sustainability. The uses for PGMs includes catalytic converters for air pollution control in vehicles, growing jewellery use, catalysts for various purposes (especially petroleum and chemicals processing), hydrogen fuel cells and many others. Given the growing importance of most of these PGM uses in more sustainable technologies or in making industrial processes more efficient, it is critical to understand the complex sustainability issues which surround platinum and PGMs. At present, South Africa is the dominant PGMs producer and holds about 88 per cent of estimated global resources, with important but relatively minor production and resources in Zimbabwe, Russia, Canada and the United States. Given the concentrated location of PGM resources, what are the likely trends in PGM mining with respect to environmental sustainability? That is, what are the costs in terms of energy, pollution, greenhouse gas emissions, water, land use impacts, social impacts, economic aspects associated with this globally important industry? This paper compiles and analyses a range of data on platinum-PGM mining, focusing primarily on South Africa. It synthesises a unique combination of data which relates typical production aspects such as ore grade and scale with sustainability aspects such as greenhouse, energy and water costs. The findings are critical in understanding the debate about the increasing environmental and social costs of some materials and technologies which are considered crucial for sustainable industries based on PGMs. Overall, the paper represents a valuable insight into the platinum-PGM sector, providing a range of useful data for understanding the environmental sustainability of this particular group of precious metals.

Jan 1, 2009

The traditional measure of Lost Time Injury Frequency Rate (LTIFR) as a measure of improvement in safety performance is recognised as inadequate and misleading, lulling managers into believing that safety is improving. It is a reactive measure, and steadily declining LTIFRs around the world have failed to be accompanied by a similar reduction in the fatality rate. This paper confronts the industry with the attitudes of some mining managers, such as one that allowed fatalities to occur in the case of a gold mining company at a rate of one death per 150 000 ounces of gold produced while claiming their safety record has improved, as shown by a falling LTIFR, and viewing fatality reductions as a long-term goal instead of an immediate priority. A quantum shift in management attitudes is required to focus on proactive measurements to detect the indicators of an impending disaster, and to predict conditions conducive to fatalities. Corporate CEOs are challenged to attend the funerals of all workers killed in the workplace. CEOs who fail to attend such funerals send a message to employees that the CEOÆs priorities lie elsewhere, and that profits take priority over workersÆ lives. The dichotomy of whether mining companies are run for the benefit of shareholders or whether companies owe social responsibility to the community is examined. The role of individual responsibility for personal safety is examined, together with the psychology of employees in the mining industry. A number of proactive measurable indicators are suggested to stimulate discussion on developing robust measuring tools to predict and therefore prevent fatalities.

Jan 1, 2003

By E J. B van Etten

This paper reports on the results of several years of monitoring rehabilitation at a silica sand mine on the Swan Coastal Plain, south of Perth. Mining here occurs below the regional watertable and leaves a post-mine landscape of dredge pond voids (pit lakes) with surrounding battered slopes. The restoration we recommended was to develop the pit lakes as wetlands of regional analogue and value. Several different restoration techniques have been applied to re-vegetate pit lake slopes over many years which have enabled an evaluation of reasons for success/failure of different restoration approaches. Learning acquired clearly showed the benefits of using fresh topsoil for restoration over topsoil that has been stockpiled for several years. Most topsoil used in restoration was from seasonal wetlands and consequently restoration was most successful in the riparian zone from the edge of pit lakes to about 2 m vertically above the water table. Topsoil restored areas above this level remained poor in plant species and cover. Conversely, remedial seeding/planting proved largely unsuccessful. Permanently and seasonally flooded pit lake margins recolonised relatively quickly and successfully with native sedges and rushes. Development of rehabilitated upper slope plant communities over time was evident with loss of typical wetland species and greater growth and survivorship of upland and dampland plant species on mid to upper rehabilitated slopes. Plant communities of lower slopes showed a converse pattern of development, with a shift towards a more typical wetland composition. We believe matching topsoil to site and development of topographic profiles similar to natural wetlands of the region are the keys to optimising restoration success of sand mines with shallow water tables.

Oct 5, 2011

In February 1995, Falconbridge Limited approved the construction of a nickel mining and milling facility on its Raglan property situated in the Nunavik region of northern Quebec, Canada. The construction period successfully terminated with the commissioning and start-up of the plant and concentrator in early-December 1997. The estimated life of the project is 20 years with an annual mining rate of 800 000 tonnes of ore, producing 21 000 tonnes of nickel per year. This paper discusses the subject of æRemote Mining in the Canadian ArcticÆ as it applies to the Raglan mine process and people. During the feasibility stage of the project, many assumptions were made which influenced the design and operating parameters of the facilities and the equipment. Transportation, communication, remote logistics techniques and standard industry practices required to support a æfly-in/fly-outÆ operation were reviewed and either adopted or rejected for use at Raglan. These assumptions were æmade to fitÆ the uniqueness of our planned operation. It was also acknowledged that many of them would ultimately impact on the people required to staff the operation following construction. Therefore, their suitability and applicability were examined from an economic, operational and human perspective. In a continuing effort to improve the quality of life for Raglan employees, as well as the economics of our mine operations, these assumptions are under constant review and scrutiny. There is no doubt that experiences gained, and willingly shared by other North American arctic mining operations, proved invaluable and are a big reason for RaglanÆs overall success thus far. The mining industry is being challenged technically to develop lower grade orebodies at the lowest possible cost. In addition to environmental constraints, serious social, political and moral questions are being asked and added to this list of challenges. Miners throughout the world must improve their operating standards and public image if we want to attract the best possible employees. Remote mining operations provide a unique opportunity to experiment with various human resource concepts as well as demonstrate the industryÆs commitment to environmental and community concerns.

Jan 1, 1998

By A Halim

"There is still debate about who should ultimately be responsible for the ventilation system in anunderground mine. The Queensland Coal Mining Safety and Health Regulation 2001, states that adedicated ventilation offi cer is the person, while Western Australian Mines Safety and InspectionRegulation 1995 states that it is the mine manager who is responsible; the ventilation offi cer actsas the managerÆs principal ventilation advisor. This paper outlines a comparison between bothapproaches."

Jun 1, 2012

The Fosterville Goldmine in Victoria employs bacterial oxidation (BIOX« Process) to liberate gold from its flotation concentrate. Gold occurrence is primarily as submicron particles in pyrite and arsenopyrite and has been described as being in æsolid solutionÆ and therefore not amenable to direct cyanidation even with fine grinding. Once liberated by the oxidation process, the gold is then available for cyanide leaching. While the oxidation process is very effective, it has been found that a portion of the liberated gold can become suspended in the liquid phase in what appears to be a colloidal state. This liquid becomes a waste stream during washing of the oxidised solids and the suspended gold is therefore lost. This paper discusses investigations into the causes of the loss and also describes the successful use of quebracho tannin in reducing colloidal gold loss. Laboratory and subsequent plant trials, showed a gain of 2.6 per cent in overall gold recovery based on mill feed and waste stream data.

Jan 1, 2009

By M P. Sandy, V Louchnikov, V Eremenko, M Orunesu, O Watson

"Surface support is a key component of most ground support systems which are applied as a means of reducing the risk of rockfall occurrence and maintaining serviceability of mine development. Surface support has two primary functions: distributing the applied load throughout the system by providing connection between rock bolts retaining smaller rocks that unravel between rock bolts.Confinement is also provided to the rock mass, which may increase its capacity to resist further degradation or loosening.Surface support has been routinely installed in most underground mines around the world for many years, yet the operators are still not always certain which type is best suited for deformable ground conditions. A number of factors need to be taken into consideration prior to selecting the type of surface support liner, such as its capacity, availability, practicality of installation, manual handling and loading conditions (static or dynamic) to ensure the system’s optimal performance in terms of safety and costs.This paper presents an overview of the surface support types currently used in underground mines in Australia. Shotcrete, weld mesh, high-tensile chainlink mesh, reinforced weld mesh and high energy absorption (HEA) mesh are discussed. A detailed description of each system is provided in terms of capacity, energy absorption, installation cycle and costs. The cost of each system has been normalised to the units of energy absorbed. The information presented in this paper can be used by underground operators as a reference guide when deciding on suitable surface support type for deformable ground conditions.CITATION:Louchnikov, V, Sandy, M P, Watson, O, Orunesu, M and Eremenko, V, 2014. An overview of surface rock support for deformable ground conditions, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 57–66 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By M Weeks

Melbourne Water Corporation, through the Pipelines Alliance, has commenced construction of a new drainage pipeline to provide additional flood protection within the Sandgate Avenue Main Drain catchment, in order to mitigate against the risk of flooding of Frankston’s central activity district (CAD).The project involves the construction of a 1550 m long, 2.5 m internal diameter tunnel, commencing upstream at the Monash University Peninsula Campus and traversing approximately west to the outlet located at Kananook Creek. The tunnel was excavated by a dual slurry-earth pressure balance tunnel boring machine (TBM), with the depth to tunnel crown ranging from 0.7 m to 14 m below the natural surface level. The TBM navigated 500 m radius curves, with a maximum drive length of 608 m. The tunnel lining consists of 2.5 m internal diameter, 250 mm thick reinforced concrete jacking pipe.The geotechnical conditions along the tunnel alignment consisted of mixed face ground conditions, predominately clay, with clayey sand and sandy clay and some sand deposits near Kananook Creek.This paper presents the challenges associated with the operation of the slurry separation plant during tunnel construction. In particular, the paper focuses the impact of slurry separation on tunnel advance rates, the lessons learnt during construction with regards to slurry separation and on the decision to adopt a dual slurry-earth pressure balance shield TBM. In addition this paper highlights the importance of having a thorough understanding of the slurry separation requirements on a slurry TBM project prior to selecting the necessary plant.

Mar 8, 2011

By H Kurth, L Balzan

On-belt analysers have been used since the early 1980s in the coal sector to measure ash content in real time for diverting material on conveyors to remove waste, bypass beneficiation and allow suitable material to proceed to the wash plant for processing. Since 2008, a GEOSCAN-M elemental analyser has been used on an overland conveyor in South Africa to divert direct-shipping quality iron ore to bypass a jig plant. This paper focusses on recent evaluation work to determine the suitability of an on-belt analyser to upgrade the processing plant feed in a copper-gold operation.Copper-gold ore samples from New Gold’s New Afton Mine near Kamloops, BC, Canada were tested to assess measurement accuracy over short time increments. A two-minute measurement increment has been used in the minerals sector as a compromise between good measurement accuracy and a useful tonnage (haul truck equivalent size or smaller). At New Afton, this increment represents approximately 35 t of material. Segregation decisions are currently made after visual and sometimes analytical determination, at increments of approximately 500 t to designate material as ore or waste at the drawbell in the cave.Results of test work including the composition range and expected accuracies by element are shown. The operation, which is not mine constrained, was evaluating the potential for ore upgrading through waste and low grade increment diversion to upgrade ore quality feeding the mill. Prompt-gamma neutron activation analysis (PGNAA) was considered as the company recognised that it would measure through the full conveyed cross section continuously and produce multi-elemental measurements unaffected by particle size, dust, moisture content, layering and segregation, mineralogy and belt speed.GEOSCAN analyses over various analysis periods will be collected to identify variability in the conveyed material quality and used to generate tonnage-grade curves so that an optimal diversion (bulk sorting) tonnage increment can be determined. Measurement increment time can be customised to suit site requirements. CITATION:Kurth, H and Balzan, L, 2017. Assessing bulk sorting suitability at the New Afton mine, in Proceedings MetPlant 2017, pp 315–323 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By R G. Richards

Although most New Zealand coals are low in ash, there are situations where high ash coals could be won. Not all high ash coals can be upgraded by physical means, since the ash is either inherent in the coal or bound in such a way to make its physical removal either impractical or uneconomic. Nevertheless, the authors believe, the situations where high amounts of ash can be economically removed by physical means to make a saleable product are considerable.

Jan 1, 1979

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill, considering mainly the role and specifications of the fill used but including brief description of fill preparation and placement. Data resulting from a Portland cemented hydraulic fill sampling, curing and cesting campaign covering about 18 months of operating practice are presented, analysed and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented, involving both Portland cemented hydraulic fill and altei._acive, cheaper, additives for cementing hydraulic Fill.

Jan 1, 1980

By M Ireland

Extensive use of diesel-powered mobile equipment in modern mines for materials handling, such as load-haul-dump machines, constitute a significant source of heat, exhaust gases and diesel particulate matter. Provision of sufficient quantities of fresh, cool air are required to remove such atmospheric contaminants from the environment for miners, particularly at depths where ventilation constraints and associated operating costs have an increasingly adverse impact. An alternative solution to diesel equipment to combat economic, environmental, social and health challenges, are battery electric vehicles (BEV), with the potential to expand production and substantially reduce ventilation and cooling demand, subsequently reducing operating costs. In this context, this paper focuses on the introduction of a battery electric loader to a diesel fleet at one of the deepest underground mines in Australia, the CSA Mine, a high-grade copper operation in Cobar, New South Wales. Analysis of a trial battery electric loader compared to existing diesel machines is performed with regards to infrastructure, technical and operational issues. Key benefits of battery electric vehicles over conventional diesel-powered vehicles are discussed, including lower energy consumption and greater efficiency, reduction of emissions and heat, reduced need for ventilation and lower operating costs. Challenges of introducing BEVs into an operation, along with the results from the comparative study are addressed under impacts to energy consumption, equipment selection, effects on ventilation and cooling, mine design and economic viability for future fleet implementation scenarios whilst meeting production targets.

Mar 29, 2023

By H Rossiter, C Simpson, J Market, P Jeanneau

Downhole Assay tools are a geophysical method to collect an instigated response from the material surrounding a drill hole and deliver a multielement proxy-assay. They were first tested in the Pilbara at the turn of this century, however since 2011 they have seen a more focused testing and implementation regime with multiple companies across multiple Pilbara mine sites. The increase in the volume of data has led to advances in the measurements and significant improvements to the efficiency of the calibration process. Pulsed Fast and Thermal Neutron Activation Analysis (PFTNA) downhole assay tools collect gamma photon spectra which are characteristic of elemental signatures. One of the key components of the technique is calibrating the spectral signatures to lab assays. Each tool is slightly different due to the organic nature of the crystal detector and therefore responds slightly differently. Environment and hole conditions as well as ore characteristics are among other external influencing factors. Thus, a unique calibration is required for each tool. In addition, not all elements are measured directly, but some are actually characterised by proxy, meaning that if the signal-to-noise ratio for an element is small, it may be easier to identify the mineral or geology in which that element is found and thus infer the concentration of the element. These proxies may differ for each site or geology type within a site. There is a large advantage to build a unique calibration per tool at each site rather than a universal one to be used across the whole province. This then delivers the accuracy and precision of measurements that mining companies require for modern operations. Early work with the tool required several thousand metres of calibration data and several weeks of analysis to build each calibration. This process has now been streamlined to significantly reduce the amount of data required and the analysis time to make it much easier to introduce new tools to a site with an existing model or to create new models. This paper details the calibration process, illustrating the increasing accuracy of the models as training data are acquired as well as the methods for transferring a calibration from one tool to another.

Nov 8, 2021