Search Documents

By L. Adler

Two basic cases involved in the design of an opening in bedded rock are: 1) where the beds deflect from each other so as to be separated; and 2) where the beds deflect onto their lower neighbor, loading the latter while reducing their own load. Analysis of case 1 is relatively simple, while the interference of the original deflection curves in case 2 complicates analysis of the latter. Figures and formulae are presented for determination of interference loading in this situation. The design of an opening in bedded rock involves two basic alternatives.1'2 In one case the beds deflect away from each other, so as to be separated from their neighbors; in the other case the beds deflect onto their lower neighbor, loading it, while reducing their own load. This is shown in Fig. 1. The first case lends itself to a simple analysis, since the upper and lower boundaries of each beam remain a free surface. In the latter case, however, due to the interference of original deflection curves, the analysis is more complex. Earlier investigators of this interference problem solved it by making the tacit assumption that this type of loading was uniformly distributed along the beam's length. While there is no intuitive justification for this assumption, its use does lead to an approximate solution. Still, a more exact solution does not require this apparently unrealistic restriction. To achieve initial simplicity, the analysis will at first be limited to a two-bedded sequence, as in Fig. 2. Since both beams have identical end conditions and spans, the original deflections of their center lines are members of the same family of curves, as shown in Fig. 3. Therefore, if interference occurs at one point along their center lines, it will occur at every point. For convenience, the midspan point is that usually examined. Deflection at midspan for a uniformly loaded beam regardless of end conditions is: where c is a constant depending on end conditions; w is the body load and equals yh, lb per ft; y is the specific weight of rock, lb per ft'; L is the span, ft; E is Young's Modulus, lb per ft2; I is moment of inertia (for a rectangular section), I = bh3/12 = h3/12, (ft4); b is the width of beam and equals one; and h is the thickness of beam, ft; or 3U > yB an Substituting the appropriate values into Eq. lb, interference between the two beds can be predicted. Should it occur, the additional loads along the lower boundary of the upper bed and the upper boundary of the lower bed must be determined. From the principle of action and reaction, these added loads are known to be equal and opposite, as indicated in Fig. 4. Since the final deflection curves for both beds are identical (Fig. 3), their successive derivatives of y with respect tox must also be identical. That is:

Jan 1, 1961

By G. Thodos, W. F. Stevens

The point-source function introduced by Horner' us a solution to the general unsteady-state equation for the flow of fluids through porous media has been utilized to calculate pressure profiles for adjacent wells as a function of time. By trial and error, the time at which the pressure waves meet to cause interference can then be calculated. For this calculation, the time of interference is arbitrarily defined as that time when both pressure waves exhibit a pressure decrease of 25 psi ar the same point within the formation. To illustrate the method, an example involving two adjacent wells producing at different rates has been worked out and is presented in detail. INTRODUCTION The initiation of production of a new well is usually accompanied by pressure drawdown measurements in order to establish the extent and characteristics of the formation. The interpretation of such pressure drawdown data is based on mathematical developments involving a single well in an infinite reservoir. If more than one well is present in a reservoir, the possibility of interaction between wells exists. Therefore, care must be taken in interpreting the pressure drawdown data. It becomes important to be able to determine when this interaction, or interference, becomes significant. This paper presents a method for the prediction of the approximate time of interference between two such adjacent wells. The basic differential equation describing the pressure distribution existing during unsteady-state flow of a slightly compressible fluid has been solved by Hor-ner.' for a constant production rate from a circular homogeneous reservoir of infinite extent. The solution utilizes the point-source function to define the pressure at various points within the formation as a function of time. The resulting expression is: q = production rate, STB/D ,;= formation volume factor, dimension-less µ = fluid viscosity, cp k = formation permeability. md H = formation thickness, ft C - fluid compressibility, psi' F = formation porosity, dimensionless R = distance from centerline of well, ft T = production time, hours Ei(—u) = Ei-function of U Eq. 1 may be used to calculate the pressure profiles generated during production from a single well in an infinite reservoir.

By R. W. Gurry, L. S. Darken

The solubility of cementite in austenite is computed by thermodynamic methods from the observed solubility of graphite. It is found that the solubility of cementite is greater than that of graphite in the entire austenite temperature range. Thus the prior discrepancy between this portion of the phase diagram and the observed metastability of cementite is partially resolved. FOR several years it has been apparent that a serious discrepancy exists in certain observations pertaining to the Fe-C system. Direct experimental data indicate: 1-That the curve representing the solubility of graphite in austenite'" crosses that for cementite4 at about 945°C as shown in Fig. 1. 2— That graphite and austenite saturated therewith are stable1 relative to cementite at all temperatures between the eutectoid, about 723°C, and the eutectic, about 1153°C. These observations are mutually incompatible in view of a well-known consequence of the second law of thermodynamics, namely, that the stable phase (presumably graphite at all temperatures) has a lower solubility than the metastable phase (presumably cementite). Hence either 1 or 2 above must be in error; either the measured solubility of graphite or of cementite, or the observation as to the stability of graphite, is in error. Our present purposes are: 1—To collate the available data on cementite and prepare a table of HO — HO° and of (Fa— HO°)/T. This tabular method seems the best and most convenient way to represent the heat and free energy of formation. 2—To determine whether the measured solubilities of cementite and graphite in austenite are in accord with the above table and the measured thermodynamic properties of austenite, in order to resolve, if possible, the existing paradox of these two solubilities. Enthalpy of Cementite The enthalpy of cementite at 273 °K, H279 — HOcem, was computed by integration of the low temperature heat capacity as measured by Seltz, McDonald, and Wells" 68" to 298 °K) and as given by the Debye functions recommended by them (0" to 68°K); the result is included in Table I. At higher temperature HCem — H,,"" is given by Kelley who used the data of Naeser7 (298" to 1037°K) and of Umino8,9 (273° to 1923°K). We have recalculated Hcem — H273 cem from the data of UminoO in the following way. In the equilibrated alloy at temperature the weight fraction of cementite Pct c -Pct cr is PctC -PctCr designated f(C), and the

Jan 1, 1952

By Nathan C. Rockwood

THE title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. DEFINITION OF MINERAL AGGREGATES "Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without portland cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. Mineral aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theoretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. EXPLORATION AND POSSIBILITIES OF DEVELOPMENT The distribution of deposits of mineral aggregate is universal, since almost any part of the earth's crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (1) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engineering talent in its operating branch, but it lacks, to a considerable

Jan 1, 1943

By U. N. Bhrany, N. Arbiter

Over the last one hundred years the problem of assessing the efficiency of energy consumption in producing rock breakage has been studied by many investigators from a variety of viewpoints. Their contributions fall into three main categories: (1) those characterized by a priori assumptions of a relation between the energy required for fracture and the degree of fragmentation produced (e.g. Rittinged(l), Kick(2) Bond(3)); (2) those studying simple systems with controlled energy applications (Gross(4)?(5) ); (3) those treating operating data to develop practical relative measures of efficiency (Coghill(6), Taggart(7)). Closely involved in the efficiency problem is the characterization of size distributions produced by comminution. Unless an experimental size distribution can be approximated by a distribution function and its constants, it becomes difficult if not impossible to develop quantitative energy-particle size relationships. While many such functions have been proposed, none are both completely adequate and convenient. The simpler fonns usually describe only a part of the sizing data, while those which apply to a greater extent are cumbersome(8). The thesis underlying the study here reported can be stated as follows: Size reduction in a tumbling mill subjects ore particles to a relatively constant fracture-producing environment. The intensity of the forces is determined by such factors as the mass of the breaking bodies (rods, balls, rock), and the speed and dimensions of the shell. For a particular ore the extent of size reduction will depend both on the intensity and on the duration of exposure. The latter is the residence time in a batch mill, or is determined by the effective volume and the flow rate in a continuous mill. Size reduction can thus be regarded as a rate process in which the weight of material in size intervals varies as a function of grinding time. Although both the rates of disappearance of coarser sizes and

Jan 1, 1961

By A. C. Fieldner, W. A. Selvig

For purposes of coal classification it is desirable to know the composition and calorific value of the pure coal substance; that is, of the coal free from its ash-forming minerals. Two methods suggest themselves: (1) To free the coal from most of the ash-forming material previous to the analysis; and (2) to analyze the coal as received and calculate the analysis, with certain more or less arbitrary corrections, to the pure-coal basis. Calculation methods are obviously more apt to give correct results with low-ash than high-ash coals. With coals of unusually high ash it would appear preferable to remove, previous to the analysis, as much of the inorganic matter as possible, by float-and-sink or acid-treating methods. Effect of Ignition on Inorganic Constituents of Coal The need of corrections in calculating analysis to the pure-coal basis is due to the fact that the ash, as determined by ignition, is not the same, in either weight or composition, as the inorganic mineral matter in the coal. On ignition a number of changes occur in the coal such as loss of water of hydration of the shaly material, conversion of pyrite (FeS2) to ferric oxide (Fe203) with evolution of the sulfur as sulfur dioxide or possible fixation of more or less of the sulfur in the ash as calcium sulfate (CaSO4), and decomposition of calcite (CaC03) to calcium oxide (CaO). The amount of sulfur from pyrite which remains in the ash as calcium sulfate depends on the amount of calcite and pyrite in the coal. Certain coals high in both calcite and pyrite show relatively large amounts of sulfate sulfur in the coal ash. The determination of total carbon and hydrogen in coal includes, besides the organic carbon and hydrogen, the carbon of inorganic carbonates such as calcite, and the hydrogen of the water of composition of some of the ash-forming minerals. For detailed discussion of corrections proposed for calculations of coal analyses to the " pure "

Jan 1, 1930

By John B. Hastings

THE reconnaissance of the Goldfield mining-district, described in this paper, was made in May and June, 1905, and, though this time was too short for a complete report, the work accomplished may serve as a basis for more thorough future research. Dr. Berkey has examined the rocks collected by myself, and I am using his classifications. As a result of further field-work, and Dr. Berkey's examination of the rocks, this paper is an elaboration and correction of my views expressed in the Gold-field Sun, May 12, 1905. The sketch-map, Fig. 1, illustrates the geology of the Goldfield mining-district. Goldfield is an eruptive complex, consisting of alaskite (binary granite), hornblende-andesite, hornblende-dacite, rhyolite, pyroxene-andesite, pyroxene-dacite (sometimes containing, a small quantity of olivine), quartz-felsite, olivine-pyroxene-ande¬site, and basalt. Considering this list to be arranged in the order of eruption, the age-sequence of the rocks conforms to Richthofen's law, formulated in 1868. From his observations in Europe and America, propylite, andesite, trachyte, rhyolite and basalt, occurring together, succeed one another. In a general way, the medium and more acidic rocks precede the most asic-a result supposed by some to have arisen from their relative position beneath the surface, and due to a rude stratification by gravity in the original cooling magma during the older history of the earth, or to the same differentiation occurring during a quiescent (molten ?) period preceding eruption, being aided by the ease with which acidic rocks, mixed with water vapors, become fusible. In effect, the more basic and less re-

Mar 1, 1906

By P. K. Guerrero, N. Arbiter

The correlation of power consumed by a tumbling mill with the dimensions, speed, and load has been attempted by three principal methods. One of these, the torque formula, has been reviewed critically elsewhere.' This approach, while analytical, disregards the individual motion and speed of the tumbling bodies and assumes that the gross geometry of the entire load is sufficient to establish the power requirement. A more general approach, using dimensional analysis, has been applied in this laboratory by the present authors1'1, and more recently by Rose.3 This disregards the internal conditions within the mill entirely and in effect is an empirical procedure for correlating data. Finally, the complete analysis of tumbling mill dynamics as first made by Davis' attempts to develop the power requirement from individual ball and rod paths and velocities. Although Davis' result is applicable only at a single speed for a given size and load it could be useful, since his optimum speed is at the upper limits of conventional tumbling mill practice. Where power values predicted by the Davis equation were compared with actual mill requirements, they were found too low for small mills and much too high for the largest mills. This suggested that the agreement with actual intermediate range requirements might be fortuitous, and the development of the equation was examined critically. The probable source of error was found to lie in an erroneous assumption made by Davis in converting the energy of ball or rod motion to power. With the same approach, but with different assumptions, a modified equation has been obtained which predicts results that are usually consistently high. This is to be expected, since it is assumed that there is no slip between load and shell and no interference among tumbling bodies. Both these effects should account for the difference. Development of Equation: When a cylindrical shell charged with a substantial weight of rods or balls is slowly rotated about a horizontal axis, the load surface first assumes an inclination that gradually increases to a maximum. Continued rotation results in failure within the load, characterized by a sliding of the top layers down the slope and a reduction in the angle of inclination. Further rotation again increases the angle, and the cycle repeats. If the speed is increased, there is continuous load failure and build-up and a continuous stream of rods or balls descends over the upcoming mass, which moves in circular arcs. At higher speeds the up-

Jan 1, 1961

By J. C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert,1,2 Russell,9 Le Conte,4 Spurr,5 Louderback,8 and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea. More recent syntheses of the geologic history have been prepared by Lindgren,7 Ransome,8 Nolan,9 Bill-ingsley and Locke,30 Longwell,11 and Eardley.12 The tentative nature of the present interpretation, which treats the structural evolution of the Utah and Nevada area, must be considered in light of the scarcity of geologic information from the province as a whole. The methods of interpreting tectonic history from stratigraphy are based largely on the concepts of Marshal Kay.23 Discussions with Hoover Mackin also have aided in organizing the Tertiary history. TECTONIC AND STRATIGRAPHIC SETTING Two approaches to the subject of the tectonic history are possible; they correspond to looking through opposite ends of a pair of binoculars. One involves an expansion and extension of detailed work and the other an interpretation based on regional geological relationships. It is believed that the second approach, used here, is not in disagreement with detailed observations. The area of the Basin and Range Province is shown in Fig. 1. Within this area middle Tertiary to Recent high-angle faulting has controlled development of mountain ranges and valleys. Only the part of the area north of Las Vegas, Nev., and south of the Snake River in Idaho will be considered in this article. Within this part of the province most of the ranges trend north-south. Approximately two thirds of the area is covered by late Tertiary to Recent valley fill and lake deposits.

Jan 1, 1961

By R. H. Atkinson, R. N. Rhoda

An improved technique has been developed for the deoxidation of palladium with aluminum which is especially suitable for use in making small castings with an induction-melting and casting machine. The effect of various crucible linings on the efficiency of the residual deoxidizer and accompanying oxide film in protecting palladium against oxidation during remelting also has been examined; the preferred crucible lining consists of zirconia cement. THE objective of this work was to develop a simple method of deoxidizing induction-melted palladium which would be suitable for use by manufacturers of jewelry and other small castings. In a common method of deoxidizing torch-melted palladium a piece of aluminum foil is dropped on the surface of the molten metal. If a film is present, which is usually the case, it must first be removed by oxidizing the molten metal thoroughly because it would interfere with the entry of the aluminum into the melt. Removal of the film is probably facilitated by a mild fluxing action of the silica crucibles which are used for torch-melting. However, removal of an alumina film from molten palladium in the crucibles normally used for induction melting is a much slower process and it became necessary to modify the de-oxidation procedure. In the modified procedure the charge is simply melted and the desired amount of aluminum, crimped to one end of a tungsten wire, is plunged through the film into the palladium and the wire immediately withdrawn. The trace of tungsten which dissolves along with the aluminum can be avoided, if considered objectionable, by using a palladium wire. In view of the persistence of the alumina film under the conditions of induction-melting it also was decided to ascertain the efficiency of this film in protecting palladium against oxidation during repeated remelting and casting. Melting Equipment and Materials The equipment used for melting and casting consisted of an Ecco GC:6, 6 to 8-kva high-frequency converter and an Ecco M34B centrifugal casting machine. This unit is being increasingly used for making jewelry and dental castings and it also has been found useful in making exploratory melts of a variety of nickel alloys, for which purpose it is well suited on account of its speed of melting and economy of material. A description of the machine and its operation will be published elsewhere.' A common palladium jewelry alloy, 95.5 palladi-um-4.5 ruthenium (referred to as "palladium" in the trade), was selected for the deoxidation tests. It was available as melting stock which had been melted in air to free it from oxidizable impurities, and also as clean scrap from previous melts which had been deoxidized with aluminum. The latter was thought to be typical of clean "palladium" scrap to be found in a manufacturing jeweler's establishment and it is also similar to one brand of "casting palladium." By the same token, the oxidized melting stock corresponds to "casting palladium" after the latter has been melted and thoroughly oxidized: Pure aluminum wire (99.9 pet), 0.032 in. diam; 1 in. = 0.036 g. Scrap tungsten wire, 0.014 to 0.020 in. diam. Argon, commercial water-pumped; 99.9 pet pure Experimental Procedure Samples of about 50 to 75 g of the palladium alloy were melted in a crucible lined with a proprietary refractory alumina cement. Some charges were melted in air, others in argon. The oxidized melting stock was melted and solidified a number of times in order to remove as much oxygen as possible before deoxidizing, but this treatment was unnecessary in the case of scrap. In either case the metal was deoxidized with aluminum (0.01 to 0.05 pet) by the

Jan 1, 1959

By Edna A. Dancy, Gerhard J. Derge

Jan 1, 1963

By A. W. Fahrenwald

Flotation practice in Idaho is now about 13 years old. The advance has been steady during these 113 years. The operators have been alert to take advantage of the newest developments and they have themselves made a constant effort to improve their work. The metallurgical improvements are due to the development of (1) better equipment, (2) better reagents, and (3) better understanding and control of the process. During the eight years the writer has been in this district, there has been continuous experimentation by several companies to improve the ore dressing by flotation methods. Gravity concentration has fought hard to hold its place, and although it is true that gravity processes have been improved during this period, nevertheless, in several of the important mills of the district the few tables that managed to hang on have finally given way. On the straight-lead ores, tables and jigs are still used; and, due to better classification, their hold on this job has been strengthened. Ores of the District The ores of the district are of two general classes: (1) clean lead ores, such as those from the Bunker Hill and Hecla mines, and (2) complex lead-zinc ores. The general impression prevails that the clean lead ores, class 1, are simple and that it is easy to obtain high recoveries and good grade products. This, in a way, is a false impression; there is quite a high percentage of locked middling in these ores at 100 and' 150-mesh sizes. Improved classification preparatory to table treatment of this type of ore has made it possible to segregate effectively a high-grade middling which is further comminuted and floated. The complex lead-zinc ores of the district, of which the ore from the Morning mine of the Federal Mining & Smelting Co. is a typical example, always have presented a difficult problem. It always has been comparatively easy to make a clean lead concentrate, but it never has been possible to concentrate sphalerite with a specific gravity of 4.10 from siderite of gravity 3.88. Also, a large percentage of the galena and sphalerite of this class of ore refuses to separate out until the crushing has been carried

Jan 1, 1928

By P. D. White, J. T. Moss, J. S. McNiel

Results of experimental work on the in situ combustion process were first published in this country in 1953' when Kuhn and Koch described results of a three-well test in Jefferson County, Okla. Shortly there-after Grant and Szasz2 described field studies in Nowata County, Okla., in which several modifications of the basic combustion process were investigated by injection of various oxidizing gas mixtures other than air. In the past five years speculation concerning this method of oil recovery has continued, with a number of interesting papers on various aspects of in situ combustion appearing in the literature3,4,5,6,7. However, only one of these' provided actual engineering information on pattern-type field experiments. The primary objectives of the Oklahoma three-well test were to check operation of specially designed electrical ignition equipment and evaluate problems associated with initiation of combustion in a natural oil sand reservoir. Immediately following successful completion of this test in the Pontotoc sand, plans were activated for a second field experiment to be conducted in the same sand a short distance away. The objective of this second field test1 as to establish a relationship between field observations and information derived from laboratory experimentation and computations. Secondary objectives of the test were to develop operating tech- niques and define operating problems, and to obtain information that would assist in the economic and engineering appraisals of the process. Careful planning was required since this test was designed with the hope of providing basic information on the characteristics and operation of a combustion drive. It was necessary to include test facilities which would not only permit precise control and measurement of the process variables but would also provide sufficient flexibility of control to insure that variables in the combustion process could be studied during the course of the test under a wide range of conditions. In order to accomplish these objectives elaborate instrumentation and several control wells were included in the design of the test installation. This type installation was felt to be well suited for an experimental study, but was in no respect intended as a counterpart of a commercial-scale operation. PRELIMINARY LABORATORY WORK An important objective of the field experiment, as stated previously, has been to obtain reliable data on operating variables which might be compared with similar data obtained in laboratory combustion tests. The value of successful correlations between quantities that can be measured in the laboratory and those obtained in a full-scale commercial venture has been well established for other industrial processes. The difficulty of following a process underground should make such correlations even more essential here. Also. approaching the field test phase of development of in situ combustion, it was considered desirable to precede design of test equipment with laboratory combustion studies under a variety of conditions to establish likely ranges of variables. These included temperature, air injection rate, frontal advance rate and produced gas composition.

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1941

By F. Haessner, M. Wilkens, U. Jakubowski

ThOUGH at present there is a wide range of possibilities for the quantitative determination of preferred orientations, pole figures of identical specimen material have not been determined by different methods as yet.''' In this paper a comparison of (Ill), (200), and (220) pole figures is presented which were obtained from a 95 pct cold-rolled high-purity cop- per sheet (99.9998 pct Cu), by three different methods. The three methods are: a) The combined X-ray reflection-transmission technique of plane samples by schulz3 and Decker, Asp, and Harker. 4 A Siemens texture goniometer was used. The experimental details are described elsewhere. 6 b) The X-ray reflection technique of spherical samples by Jetter and Boric.' A Siemens texture goniometer with some modifications was used. The samples were prepared by sticking 140 polished sheets together with an adhesive and machining a sphere (20 mm diam).* Additional

Jan 1, 1967

By Ernest M. Spokes

For bituminous and lignite coals the economic picture continued to improve as it has each year since the low of 1961, with production at 480 mil- lion tons in 1964 compared with 1963's 459 million tons. The anthracite industry produced 16.3 million tons in 1964 and 18.3 million tons in 1963. The industry is looking toward a further expansion; among the new developments will be a mining wheel producing 3 million tons of lignite per year in South Dakota. It is expected that electric power generation will continue to provide the market for most of the increase in consumption, with exports second in importance in the expansion. Improvements in methods of mining and transporting coal underground and in strip mines, and the cooperation of carriers in finding ways to reduce transportation costs to distant markets, have made possible these expansions. Research continues to reduce costs of mining, transportation, steam generation of electric power and production of steam for space heating and manufacturing processes, to retain some markets and expand others. Other research seeks to expand markets by developing fuel from coal which will be more attractive than competing fuels, by reducing sulfur and other sources of air pollution. Public relations efforts of the industry are bearing fruit in a greater acceptance of coal as a modern fuel.

Jan 2, 1965

By E. J. Wasp, N. T. Cowper, R. A. Davis, W. F. McDermott

On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this $5 million installation climaxed three years of development, testing, and construction. The mine and concentrator are located approximately 30 miles from the town of Waratah in a rugged semi-mountainous terrain. The open pit mine will produce approximately 5 million long tons a year of crude ore, which is ground in autogenous mills, separated magnetically, thickened and prepared for the pipeline. The 53-mile pipeline transports the 2,250,000 tons of concentrate north to Port Latta. The Port Latta facilities include the receiving, storage and thickening equipment for the slurry as well as filtering, balling and pelletizing equipment to produce the 2,250,000 tons of high grade iron ore pellets. Five vertical shaft furnaces are used for pelletizing.

Jan 1, 1969

By R. J. Wensley

THE use of small substations for the supplying of 275-volt energy to the locomotive and cutting machines in coal mines is a well-established practice. A few years ago, when labor costs were lower, these substations were located as near to the load as possible, and an operator was provided for each station. This practice has now become so expensive that substations are being located with reference to other mining machinery, such as hoists or pumps, so that one operator can look after both. Some-times the substation is operated by one whose duties make him traverse quite a large area. In such cases the interruption of alternating-current supply may produce a long interruption in the direct current, as the station cannot resume service until this man reaches it. Such interruptions interfere seriously with production and may easily counterbalance the supposed saving gained by such operating methods. The grouping of substations for convenience in operating may also result in excessive copper loss and consequently poor trolley voltage, with its attendant evils of low locomotive speeds and increased locomotive motor maintenance. The speed of the coal-cutting machines will also be reduced. By relieving the substation of its, burden of the operating labor cost, the most economical location, from an electrical standpoint, may be chosen. The matter of machine insurance should also be considered. If an attendant is caring for several kinds of equipment, he cannot watch the machine continually for signs of trouble; therefore, continued overload, phase failure, low alternating-current voltage, bearing trouble, etc. may result. Some partly automatic equipments have been installed; these have protection against low voltage, reverse current, and bearing trouble and are provided with automatic reclosing circuit breakers. This is a step in the right direction but it does not go far enough to give first-class machine insurance.

Jan 9, 1921

By Samuel M. Shallcross

The principal function of the Bell limestone mine, of the American Lime & Stone Co., at Bellefonte, Pa., is to supply raw material to the company's modern rotary kiln plant at Bellefonte. Because mining costs are naturally higher than many open quarries with more favorably lying strata, it cannot compete, except to a limited extent, in the markets for road material and fluxing stone. In the broad sense, mining does have an advantage over the average open quarry when the end products are designed for and controlled by process and final inspection for the exacting demands of the industrial and chemical markets. Approximately 80 per cent of the output of the Bell mine is sold in the industrial and chemical markets. And as higher standards are set each year for construction and agricultural work, the remainder of the mine output goes to these two classes. Mining produces more fines than open quarries, and these fines are difficult to market; on the other hand, owing to absence of contaminating clay and impure rock, a greater percentage of the output of a mine is marketable. Because of the great production of fines, rotary kilns for lime burning are necessary when the stone must be mined. In 1921 the American Lime & Stone Co. operated 19 quarries and 72 lime shaft kilns spread over an area of 40 miles between Bellefonte and Altoona, Pa. At that time the lime-production capacity of the 72 kilns amounted to approximately 700 tons per day. After 15 years the company operates three rotary kilns and six shaft kilns, with a combined output of approximately 500 tons of lime per day, concentrated in its single Bellefonte plant (Fig. 1). Its only stone-producing plants are now the limestone mine at Bellefonte and a construction-stone open quarry at Union Furnace, near Tyrone, Pennsylvania. Since the middle of 1922, the management of the American Lime R. Stone Co. has been under the direction and ownership of the Warner Company, of Philadelphia. To the Warner Company's experience, gained through successful operation of lime plants in eastern Pennsylvania for many years, and the successful solution of material-handling problems

Jan 1, 1937

By Thomas C. Wilder

Jan 1, 1965