Search Documents

By D. H. Gieskieng

THE advent of curved jaw crusher wearing plates made an approach other than segmental layout analysis desirable for prediction of capacities. For some time it had been known that the drawing board capacities of crushers using these plates had to be considerably modified by complicated experience factors to achieve agreement with results. Because these apparent capacities could be readily increased severalfold by minor crushing chamber shape changes, it was necessary that the utmost precaution be taken in predicting capacities of jaw plates modified for nonchoking, special wear characteristics, or any other reason. To this end the laboratory and field tests outlined by the author in a previous paper1 were made on Blake-type jaw crushers. The results of these tests were summarized in a simple first degree equation applicable to crushers using either straight or curved jaw plates. This equation first outlines the maximum capacity potential of a given crusher, then reduces this figure in accordance with installation circumstances by means of a realization factor. It was found subsequently that this equation, with the addition of an eccentric throw factor, is applicable to standard types of single-toggle or overhead eccentric jaw crushers as far as maximum capacity potential is concerned. However, these crushers have realization factor curves somewhat different from those outlined for the Blake type. While this paper is concerned principally with standard type single-toggle crusher capacities, the evaluation of data obtained with these machines is simplified by comparative reduction to the 10 x 7 in. Blake-type equivalents upon which the summary of the preceding paper was made. Convertibility of data from one type of crusher to the other also tends towards confirmation of both. The agreement of these data is sufficient to be considered complimentary. Consequently the feed factors, f, previously reported for Blake crushers are slightly adjusted to an average with the single-toggle crusher results. Blake-type equation: C = f.d.w.y.t.n.a.r [I] Single-toggle type equation: C = f.d.w.y.t.n.a.e.r [21 where C is the capacity in short tons per hour through the crusher, f is a feed factor, dependent upon the presence of fines in the feed, and the surface character of the jaw plates used. Values of f : Smooth Plates Corrugated Plates With normal fines 0.0000414 0.0000319 Fines scalped out 0.0000368 0.0000252 Large pieces only . 0.0000312 0.0000215 d is the apparent density of the broken product in pounds per cubic foot. (If the true specific gravity of the feed is known, 40 pct voids may be assumed and d becomes 37.4 times sp gr). w is the width of crushing chamber in inches. y is the openside setting of the crusher, in inches. In the case of corrugated jaw plates it is measured from the tip of one corrugation to the bottom of the valley opposite. t is the length of jaw stroke in inches at the bottom of the crushing chamber. It is the difference between open and close-side settings. n is rpm, or crushing cycles per minute, a is the nip-angle factor. It is unity for 26" and 3 pct greater for each less nip-angle degree. A nip-angle of 20" has an a value of 1.18, and an angle of 30" has an a value of 0.88, see Fig. 1. r is the realization factor. It is unity for perfectly uniform choke feeding and usually less for actual operating conditions according to the method of feeding used and the probabilities of hang-ups involving the size of feed and crusher opening. Approximate values are given by the curves in Fig. 2. These values are further reduced by intermittent feeding, e is the throw or diameter of gyration of the single-toggle crusher eccentric in inches. As evident in Fig. 1A, variation of feed size will generally have little effect on nip-angle if both jaw plates have flat areas. Jaw plates having continuous curvature, as in Fig. 1B will have different nip-angles, depending upon the size of feed. For test work as described in this paper this effect was accounted. For general compilation of capacities for average feeds it is suggested that the nip-angle be taken at the various settings computed, at an arbitrary level, such as is indicated in Fig. 1C. Data Evaluation To bring the Blake and single-toggle type crusher capacity test results to common terms for evaluation, all data are converted to terms of 10 x 7 in. Blake-type performance at conditions of 100 lb per cu ft, 10 in. chamber width, 250 rpm, 0.65 in. stroke, 3-in. openside setting, and 18° nip-angle. (The nip-angle of the 10x7 in. Blake is 18° at 3-in. setting.) The single-toggle crusher performances are also divided by the eccentric throw to bring this effect to unity. As outlined,' laboratory and field tests made on Blake-type crushers ranging from 10 x 7 in. to 60 x 48 in. were summarized along the foregoing conditions of speed, stroke, etc. This resulted in groups of data which correspond to feeds with fines, feeds

Jan 1, 1952

By Newell G. Alford

With the workable area of coal prospected and known as to workability and quantity and sampled and tested for desired quality comes the determination of the projection and method of working. The best method will be the one supplying the greatest degree of safety, the most merchantable product, the minimum average cost per ton with the largest yield of recoverable coal. Based on coal elevations, taken at the bottom of the seam on all known outcrop exposures, prospect openings or drill holes, coal contours are made on the map to be used in developing the mining plan. The contour interval should be as close as available information will permit. For general utility in layout of mining, haulage, drainage and ventilation, a map scale of 400 ft. per in. is preferable. In mountainous sections, location of the main out- crop opening or hoisting shaft is often limited by the available railroad route and amount of land level enough for a plant site. In level country, where a tipple and hoisting shaft may be placed at will, choice of the plant site should depend on the minimum average underground haul for the total coal to be worked to the new

Jan 1, 1932

By H. O. Hofman

INSTITUTE OF TECHNOLOGY, In deternlining experimentally the fusibility of clays, two kinds of methods may be distinguished—the direct and the indirect. Of the direct methods, that of Seger has found

Jan 1, 1899

By N. O. Gray, John Henderson

Hydrogen-reduction data for naturally occurring single crystals and Prepared polycrystals of dense hematite have been presented. Results cover the temperature range 400o to 1000oC, for particles from ten sources, ranging in size from 0.07 to 10 mm and in shape from spheres to cylinders, cubes, and thin slabs. A consistent pattern of behavior has been demonstrated for single crystals and the reduction mechanism shown to be temperature-dependent. Below 579oC reduction is a simple topochemical process but at higher temperatuves it is complex and occurs in two distinct stages. Prepared particles from these laboratories behave in a similar manner to the single crystals. Data from two investigators showing topochernical reduction of Prepared particles above 575°C are inconsistent with that for other dense hematites. It is concluded that topochenzical reaction should not be used as a model for generalized rate expressions for dense hematites. SINCE 1958, McKewan1-6 has brought to prominence a simple concept of dense hematite reduction. This model is that oxygen is lost from a hematite particle undergoing reduction only from an oxide-iron interface that recedes in such a way that the oxide remaining retains the original shape of the particle, i.e., reduction occurs topochemically. An adjunct to this concept is that any intermediate oxides in the transition from hematite to iron only form thin layers so that oxygen cannot be lost from the particle without movement of the oxide-iron interface. Further, the rate of oxygen loss from the particle is said to be proportional to the area of the receding interface so that the iron layer grows linearly with time and the over-all reduction process can be described by the equation where ro and do are the initial particle radius and density, respectively, R is the fraction of the original oxygen lost, i.e., the fractional reduction, at time t, and K is the rate constant. The idea of an underlying simplicity in hematite reduction is attractive because it gives a tractable basis from which general theories of hematite reduction can be developed and it has received wide support,7-14 based mainly on the large amount of data13 that can be fitted to Eq. [I]. However, despite the fact that this equation has been derived for dense materials, the bulk of the data that have been used to test it13 have been for materials of only about 90 pct of theoretical density (5.26 g cm-3) or less, so that its generality for dense hematites has not been demonstrated. In any case, as will be seen, adherence of reduction data to Eq. [1] does not necessarily imply that reaction occurs topochemically. In this work only data for hematites approaching theoretical density are considered and it will be shown that in only one study besides McKewan's is topochemical behavior observed over the whole range of temperature investigated. For the majority of materials a linear rate of interface advance is observed to complete reduction only when wustite is not a stable intermediate phase in the transition of hematite to iron, i.e., at temperatures below about 575°C. Above this temperature, reduction is an exceedingly complex series of reactions that takes place in two distinct stages and it is only in the first stage that reaction in any way resembles a topochemical process. This means then that, far from representing general behavior as has commonly been supposed, topochemical reaction for dense hematites is only a particular behavior that may be observed under some circumstances. EXPERIMENTAL Hydrogen-reduction data have been collected and cross-checked in these laboratories by three techniques, weight loss, collection of water evolved in the reduction reactions, and direct metallographic examination. Details of these techniques are discussed elsewhere," where it is shown that results obtained by the three methods are in close agreement. The weight-loss method, by which most of the results were obtained, consisted of hanging the sample in a platinum mesh basket from an Ainsworth Model AV-AU-1 vacuum recording balance inside a vertical l 1/4-in.-ID alumina tube furnace. Dry deoxidized hydrogen was flowed downwards through the tube at 2 to 4 liters min-1 (stp). Single crystals from two sources and artificial oxides from three sources have been examined. The single crystals were from hematite deposits at Yampi Sound, Western Australia, and Brazil, the latter being obtained from Gregory, Bottley and Co., London, U.K. The "Yampi Blue" crystals were hand-picked from washed, magnetically concentrated, sized fractions, -200 mesh BSS (mean diameter ca 0.07 mm) and —36 + 44 mesh BSS (mean diameter ca 0.4 mm) while 10-mm cubes were cut from the Brazilian crystals with a diamond saw. The starting materials for the prepared particles were hematites designated, respectively, "Specpure Iron Oxide", Laboratory No. S639 from Johnson Matthey & Co. Ltd., London, U.K., "Calcined Ferric Oxide" from B.D.H. Laboratory Chemicals Division, Poole, U.K., and "Pigment Grade Oxide", EPR-50, from C. K. Williams & Co., Easton, Pa., U.S.A. Approximately spherical particles were prepared from the artificial oxides by rolling the material, moistened if necessary, in a glass jar, and cylindrical compacts approximately 10 mm in diam and of approximately equal height were pressed in a steel die at 200 psi. These spheres and cylinders were subsequently fired in oxygen for 20 to 100 hr at 1370°C. The

Jan 1, 1967

By Michael J. Bailey, Peter M. Douglass

INTRODUCTION Spoil pile slope failures can have costly consequences. In- stability in the form of a single major event or as a recurring problem can 'mean lost production, lost resources and damaged mining equipment. In extreme but not uncomnon cases, a major spoils slide can force the closure and abandonment of a pit. Slope stability is affected by mine operating practices as we1 l as geologic conditions and material parameters. Mine operators can enhance spoil pile stability through constructive changes in their operations. Attention to the causes of in- stability can lead to development of operating practices tailored to site specific problems. Action aimed at limiting future instability is frequently more cost effective than continually "coping" with unstable spoils. The effect of mine operations on material properties is often overlooked because the "data" are not easily quantified nor input directly into stability analysis equations. We have found, however, that miners' experience with their own operation, as well as data pooled from similar operations, yields relation- ships which can be utilized to solve stability problems. The repetitive nature of area type surface coal mines with successive spoil pile rows further enables the development of useful site specific relationships. Stability problems can be mitigated by applying these relationships.

Jan 1, 1983

By L. L. McDaniel

Copper smelters of various kinds have operated in the Morenci district since 1872, but all have been abandoned with the exception of the present Morenci Smelter of Phelps Dodge Corporation, which was completed in 1942. During the five-year period starting in 1937, the Morenci ore body was prepared for open pit mining, pilot mill test work was carried out, and a complete reduction works, of which the Smelter is a part, was designed and erected. Actual construction work on the Morenci Smelter was started in the fall of 1940, and warming up of the units began on April 1, 1942. Charging of the reverberatory furnaces commenced on April 18, 1942, and the first anode copper was produced on April 26, 1942. The smelter was originally designed to handle the production of the Morenci Concentrator on a 25,000 ton per day program, but by the time the smelter was in operation, plans were already underway to increase the smelter capacity to handle the production of the concentrator which was being enlarged to 45,000 tons a day capacity as a war-time necessity. This extension to the smelter was completed and the new units were put in operation toward the beginning of 1944. The original smelter consisted of a smelter crushing plant, bedding plant, two direct-smelting reverberatory furnaces with two waste-heat boilers on each furnace, three converters, an anode department, a stack, and all of the usual accessory smelting equipment. The extension consisted of increasing the bedding plant from three to five beds, the reverberatory department from two to four furnaces, and from four to eight waste-heat boilers, and the converter department from three to six converters. A third converter aisle crane was added and additions were made to the flue systems and conveyor systems throughout the smelter; but no change was made in the smelter crushing plant or the anode department, and the same stack was used for all additional Smelter units. A blister casting machine was installed at that time in the south end of the converter aisle to handle excess and emergency production above the capacity of the anode department and in 1947 a converter aisle skull breaker and a lime burning plant were added as the final units for a complete plant. The choice of direct smelting over calcine smelting for the Morenci Smelter was made after careful study by members of the Western organization of Phelps Dodge Corporation and after test runs on direct smelting of Morenci concentrate had been made at the Douglas Smelter of Phelps Dodge Corporation. The Morenci furnace charge is made up of comparatively high grade concentrate with no ores of smelting grade available and with only flux, a small amount of copper precipitate and the usual amount of smelter secondaries to be smelted with the concentrate. The simplicity of direct smelting for this charge and the large amount of waste-heat steam available from direct smelting operations were factors influencing the decision to adopt direct smelting for Morenci. The design of the Morenci Smelter and the type of units selected followed best experience at the Douglas Smelter of Phelps Dodge Corporation. A description of the original smelter before operations started was given in an article in the May 1942 issue of Mining and Metallurgy. The purpose of the present article is to describe the enlarged Morenci Smelter, with a discussion of metallurgy and operating practice and to show tabulations of operating and metallurgical results obtained. Because of beginning operations during the early years of World War 11, many problems caused by labor shortage were encountered, but no major difficulties developed in starting the new plant. However, because of labor shortage, full scale Smelter production was not reached until the fall of 1946. Fig 1 shows a general plan of the Morenci Reduction Works. The arrangement of the smelter equipment is shown in Fig 2, a sectional view of the smelter is shown in Fig 3, and the smelter flow sheet is shown in Fig 4. Metallurgy The metallurgy of direct smelting, being more or less fixed by the character of the charge, is not subject to the control available in calcine smelting. Slags may be modified by the addition of suitable fluxes, but the grade of the matte is determined almost entirely by the iron:copper ratio of the concentrate. The direct smelting operation involves distributing the wet concentrate along the sidewalls and in the bath of a reverberatory furnace by means of some suitable feeding device and raising the temperature of the charge so that first the moisture is driven off, then the first-atom sulphur is eliminated, and finally the sulphide portion of the charge melts and runs into the bath, carrying with it the non-sulphide portion which has been partially fluxed to form a suitable slag. The fusion of the non-sulphide portion is completed by contact with the irony converter slag which is regularly being poured into the reverberatory furnace. The smelting rate of the charge is influenced by the mineralogi-cal composition of the sulphide portion of the concentrate and by the composition and amount of the non-sulphide portion including the fluxes added. The copper in Morenci concentrate is chiefly in the form of chalcocite, intimately associated with pyrite, and non-sulphide content is very low so that

Jan 1, 1950

By John J. Cioston

THE steadily rising flood of gold production from all parts of the world has created an avalanche of rumors regarding the stability of the present price of this metal. Markets have been unsettled from Johannesburg to London from New York and Toronto to Melbourne, despite repeated denials from, American and British authorities of any immediate intention to alter the price. Various economists and financial writers have blossomed forth with predictions that the price would be set at the old level of $20.67 per oz.; some have even been so brash as to state That a price of $15 would be necessary to bring production within control. These effusions, based entirely upon monetary theories and with no regard to production costs, serve to confuse rather than clarify the situation.

Jan 1, 1937

By Robert A. Rapp, Ronald L. Pastorek

Solid-state electrochemical measurements by three alternative experimental procedures were made with the cell FeO, Fe3O4 |Zro.85Cao.15O1.85 |Cu| Zr0.85CaO.15O1.85 | FeO, Fe304 to establish the solubility and diffusivity of oxygen in solid copper in the temperature range 800" to 1030°C. The solubility of oxygen in solid copper and the diflusivity of oxygen in solid copper Dgu = 1.7 X 10-2 exp(-16,000/RT) Cm2/sec were determined and confirmed in alternative experiments. The enthalpy of solution of oxygen in solid copper equals —10,000 cal per mole; the partial excess entropy of the oxygen atoms in the Cu-O dilute solution is approximately the same as that found for interstitial atoms in other metals. The diffusivity of oxygen in solid copper is consistent with that expected for an interstitial atom. RELIABLE values for the saturation solubility N(s) and diffusivity DO of oxygen in solid copper have not been unambiguously established in the literature. Following three early determinations by others,1"3 Rhines and Mathewson4 reported that the solubility of oxygen in solid copper increased from 0.007 at. pct 0 at 600°C to about 0.015 pct at 1050°C. Phillips and skinner,, using essentiially the same analytical procedure, reported that the solid solubility increases from 0.0018 at. pct 0 at 550°C to about 0.0075 pct at 1050OC. The only previous value for the diffusivity of oxygen in solid copper was reported by Ransley.6 Ransley deoxidized Cu-Cu2O alloys in an atmosphere of carbon monoxide gas to yield a solubility-diffusivity product. He used the solubility data of Rhines and Mathewson to calculate the diffusivity values. Another method for obtaining the solubility-diffusivity product (N(s) DO) is by measuring the widths of internal-oxidation zones in copper alloys as reported by Verfurth and Rapp.7 However, the calculated N(S)Do products depend upon the alloy content of the specimen, so that the internal oxidation of copper alloys does not follow ideal internal oxidation kinetics. As a result, unequivocal values for the N(s) DO product were not obtained by this procedure. A solid-state coulometric titration technique similar to that employed in this work was introduced by C. Wagner8 to study the dependence on silver activity of the Ag/S ratio in silver sulfide in the temperature range of 160" to 300°C. Similar experiments have been carried out by C. Wagner and co-workers9-11 to study the stoichiometry range of silver and copper tellurides, cuprous sulfide, and cuprous selenide. Numerous authors have carried out electrochemical measurements with a solid oxygen-ion-conducting electrolyte to determine the solubility and/or diffusivity of dissolved oxygen in several liquid metals.12-l6 Rickert and Steiner17,18 have used solid-state electrochemical measurements to determine the diffusivity of oxygen in solid silver from 760" to 900°C. Two different cell geometries were used. In the cell of linear geometry Fe, FeO | ZrO2 + (CaO) | Ag + [0 (dissolved)] [1] oxygen diffused from the interior of the silver electrode to the silver/electrolyte interface where the oxygen activity had been lowered from a fixed initial value to practically zero by the application of voltage to the cell. The diffusivity of oxygen in solid silver was determined from the solution of the diffusion equation and the time dependence of the cell current. However, this determination of the diffusion coefficient depended upon a knowledge of the solubility of oxygen in solid silver. A cylindrical geometry was used for the cell Pt, O2(Po2 = 0.21 atm) | ZrO2 + (CaO) | Ag + [0 (dissolved)] [II] which also allowed the diffusivity of oxygen in solid silver to be determined. These values were in agreement with other available data.l9 Recently, Raleigh20,21 used a method involving the measurement of diffusion-limited currents in a cell involving the AgBr solid electrolyte to determine the diffusion coefficient of silver in Ag-Au alloys at 400°C. Diffusivity values on the order of l0-14 sq cm per sec were measured in the alloy composition range 10 to 60 at. pct Ag in a single experiment. From numerous electrical conductivity and galvanic cell measurements,9'22"26 the solid solution Zr0.85 Ca0.15 O1.85 has been established as an electrolyte with predominant oxygen ion conduction over a wide range of intermediate and high oxygen activities. For interrelating the thermodynamics and the kinetics of the dissolution of oxygen in solid copper in this investigation, a galvanic cell was constructed with FeO-Fe3O4 as the reversible reference electrode, the Zr0.85Ca0.15 O1.85 electrolyte, and a pure copper specimen under-saturated in oxygen as the other electrode. THEORETICAL ANALYSIS Three variations of a high-temperature electrochemical technique were used in this study to provide two determinations each of the solubility and diffusivity

Jan 1, 1970

By J. W. Powell, F. H. Spedding

A complete review of the use of chelating agents in the sepa ration of rare earths by ion-exchange is given as well as a concise description of the recent pilot-plant operations of the Ames Laboratory. The two chelating agents which show the greatest promise are ethylenediamine-N,N,N',N'-tetraacetic acid and N'-(2-hydroxyethyl)ethylenediarnine-N,N,N '-triacetic acid. The first successful separations of rare earths by ion exchange were reported in a collection of papers which appeared in the November, 1947, issue of the Journal of the American Chemical Society.1'9 Some of this work was performed at the Ames Laboratory of the A.E.C., the remainder at the Oak Ridge National Laboratory. The processes developed at Oak Ridge, as well as some of the early Arnes methods, employed 5 pct citric acid-ammonium citrate eluant at low pH and were carried out on either H+-state or NH:-state resin beds. These techniques were successful for the separation of small quantities of either naturally occurring or radioactive rare earths and are still used for the isolation of rare-earth activities from fission products. Concentrated citrate is not economical, however, for use in moderate or large-scale rare-earth separations. For this reason, the Ames Laboratory turned its attention to lower concentrations and higher pH's in order to make more effective use of the eluting agent.10-14 Although elutions have been performed successfully over a wide range of conditions, 0.1 pct citrate at a pH of 8.0 is highly recommended for use on H+-state resin beds.15,16 Elu-tion with 0.1 pct citrate in the pH range from 5 to 9 brings about the separation of the constituent rare earths into a series of flat-topped elution bands which progress down the resin bed, head to tail, without actually pulling apart as do the rare-earth peaks which develop when trace quantities are eluted with 0.25M (5 pct) citrate at low pH's. Because of this, elution with 0.1 pct citrate at pH 8.0 do not produce pure rare earths unless sufficient quantities are present to provide developed bands which are at least several inches long on the columns. Although other eluting agents have proved more effective than citrate solutions, articles concerning the use of citric acid for separating rare earths still appear in the literature occasionally. For example, Ketelle and Boyd17 reported some further studies on the separation of rare earths with 5 pct citrate in 1951. They used 270 to 325 mesh Dowex-50 columns at 100°C and a pH of 3.28. vickery18 compared the effectiveness of a number of eluants for the separation of rare earths on NH+4 state Dowex-50 in 1952. He found that citric acid was more efficient than acetic, malic, tartaric, and aminoacetic acids. In 1953, Mayer and Freiling18 reported that citrate was inferior to malate, glycolate, lactate, and EDTA for the resolution of Sm-Eu and Y-Tb mixtures on 250 to 500 mesh, NH+4-state, Dowex-50 at 87°C. pinta20 used 5 pct citrate in the pH range 2.8 to 3.4 to obtain some rare earths for analytical work the same year. Trombe and Loriers21 reported the use of citric acid in their laboratory to separate rare earths in kilogram quantities. Lariers and Quesney22 reported some separations with citrate in 1954. They used 5 pct citrate at pH 2.8 to separate yttrium and the yttrium-group rare earths from the cerium-group rare earths. briers23 used 5 pct citrate at pH 3.2 and 90°C as late as 1956 to isolate thulium in fair purity. For the separation of tracer quantities of rare earths, Mayer and Freiling19 have recommended pH 5.00, 0.24M lactate at 87 °C on 250 to 500 mesh, NH+4-form Dowex-50. Freiling and Bunney24 have also employed lactic acid for the separation of fission-product rare earths. Cunninghame, Size-land, Willis, Eakins, and Mercer25 have reported a 4-hr separation of Y, Eu, Sm, Pm, Nd, and Pr with 1M lactic acid at pH 3.25 on Zeokarb-225 at 87°C. Stewart, et al.,26 reported separation factors for rare earths distributing between Dowex-50 and 0.25M glycolic acid. stewart27 also reported a 30-61 separation of Y, Tm, Er, Tb, and Lu tracers with buffered, 0.25M glycolic acid containing 0.05 pct Aerosol OT. The resin bed was 400-mesh Dowex-50 (X12). The pH of the ammonia-buffered eluant was 3.5. Various aminopolyacetic acids have also been used to obtain varying degrees of separation of the rare earths. In 1951, Fitch and Russell28 investigated iminodiacetic acid (IDA) and nitrilotriacetic

Jan 1, 1960

By Thomas J. Sawarynski

This paper discusses current trends of coarse and fine coal refuse disposal techniques. Emphasis is on site-specific engineering used by coal companies to tailor safe, cost effective, and environmentally sound refuse disposal system to the needs of a particular mine. Geotechnical design considerations will be discussed in relation to system performance, regulatory acceptance, and industry use.

Jan 1, 1982

By ERNEST A. HERSAY

ACCURATE ore-sizing with screens is drawing attention to certain details that now, more than ever before, require attention. There are many tests that must be preceded by careful sizing. The assayer often could profit by a more careful selection of screens. In milling, more attention is given the slimes produced. Cement-manufacturers are pulverizing and screening finer than they formerly did, and others are reducing materials to fine sizes at high cost, with screens used to govern the fine¬ness of the pulverized product. Fine screens are expensive, easily injured by mis-use, are carried in stock sparingly by most dealers, and are handled often by those who know little about them except their designated number. More attention, on the whole, needs be given the actual size of the mesh-openings, and less emphasis placed upon any custom or conventionality in numbering. An effort to classify wire screens, in this respect, leads at once into computations, where one is confronted with details of sizes and standards, of different wires, different gauges, and different customs. There is always uncertainty about the exact working-size of a screen until one gives the matter special attention, and devotes more time to it than its simplicity seems to demand. To know only the number is not sufficient for all uses. Often, in sets, superfluous sizes are used; and sizes are omitted that are of critical importance. In wire screens, the use of different standard sizes of wire makes important differences in dimensions that must be taken into account. The dealer usually grades screens by the number of openings per linear dimensions, regardless of the size of the openings or of the wire. Certain 100-mesh screens in use are found, by measurement, to he actually coarser than others of 90-mesh, a result which is due, of course, to the use of larger

May 1, 1906

By J. F. Abel, F. T. Lee

Subsidence is controlled by a complex com¬bination of mining and geologic factors. For example, a compilation of worldwide data shows that, as the percentage of shale in the overlying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the over¬burden appears to cause a more than twofold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted, the smaller percentage of that thickness shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room-and-pillar panels de¬pends on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1984

P. Herasymenko (New York University, New York) —The authors' experiments on equilibria between water vapor and liquid synthetic slags represent a valuable contribution to our knowledge of the nature of liquid slags. They can be regarded as a proof of ionic splitting of water molecules dissolved in slags. The assumption that water dissolved in slag was com- pletely ionized was made in my report on hydrogen equilibria in steelmaking as early as 194010. In that paper, the first systematic data were given on the content of ionized hydrogen in acid and basic open-hearth slags. The paper probably escaped the notice of the authors, although they mention the articles published later by other investigators who reported erratic and

Jan 1, 1958

By E. Douglas Sethness

The uranium industry is booming. In Texas alone, there are about 22 different companies with active exploration programs. Twelve solution mines have been permitted; three surface mines have been authorized; and two mills are currently in operation. However, the industry also has a problem, and that is the disposal of radioactive wastes. Over the past several years, stories concerning nuclear wastes have appeared frequently in the news. One of the most frequently cited cases occurred in Grand Junction, Colorado. In 1966, after ten years of investigations, the U. S. Public Health Service (PHS) discovered that tailings from a uranium mill were being used as fill material and aggregate for local construction purposes. It was estimated that between 150,000 and 200,000 tons of material had been removed and used under streets, driveways, swimming pools, and sewer lines. In addition, tailings had been used under concrete slabs and around foundations of occupiable structures. Further studies prompted the Surgeon General to warn that the risk of leukemia and lung cancer could be doubled at the measured radiation levels. More recently, the L. B. Foster Company discovered that its building site in Washington, West Virginia, was radioactive. While digging a foundation, the ground erupted and a ball of fire 30 feet high shot out. Evidently, the dirt was laced with radioactive thorium and zirconium, a potentially explosive mixture contained in a Nigerian sand which had been used by the previous site owners in the manufacture of nuclear fuel rods. Just this month we have read about legal suits to stop exploration for a nuclear waste disposal site in Randall County, Texas. The U. S. Department of Energy is trying to locate a deep underground nuclear waste depository for final burial of over 76 million gallons of high-level wastes. The problem is acute, the wastes are accumulating at a rate of about 300,000 gallons per year. Nor do these numbers include the spent fuel elements from nuclear power plants that are in temporary storage facilities. Fortunately, public awareness of these and other related issues is high. Unfortunately, the differences in the waste products from the nuclear fuel cycle are not always apparent to the general public. There are two distinct types of radioactive wastes: "high-level", which consist of spent fuel or wastes from the reprocessing of spent fuel; and "low-level", which, in general, are by-product wastes. There are numerous non-technical definitions that can be applied to help the layman differentiate between high-level and low-level wastes. For this latter purpose, it is best to think of them in terms of what we can see and feel. In general, high-level wastes are physically hot and can cause acute radiation sickness in a short period of time. Low-level wastes are not hot, but may cause chronic health effects after long exposure. The wastes which we are concerned with in the uranium mining and milling industry are low-level wastes. As recently as ten years ago, there were very few controls or regulations governing tailings disposal methods. At the same time, mine reclamation was not enforced through either state or Federal laws and the long-term viability of abandoned tailings ponds was not assured. The regulatory climate has changed significantly in the last decade, however. The low-level radioactive wastes generated by uranium mining and milling are generally contained in a tailings pond. Approximately 85-97% of the total radioactivity contained in uranium ore is present in the mill waste that goes to such tailings ponds. The isotope Radium-226 is probably the most potentially harmful radioactive parameter in the ponds. Radium emits gamma radiation and is also an alpha particle emitter. Because gamma radiation is very penetrating, it presents a potential health problem when a source is located external to the body. Gamma radiation will go through the body, causing damage to each cell encountered on the way. Although alpha particles have very little penetration capability, they can cause extensive cell damage. For this reason, alpha particles are a problem after inhalation or ingestion. Radium creates a health hazard by both of these mechanisms. Radium decays to radon gas which can be inhaled and serve as an alpha particle emitter. Additionally, radium is very soluble and readily enters the natural hydrologic cycle if allowed to leach from a tailings pond. With a half-life of 1620 years, radium has plenty of time to be taken into the food chain and end up in our bodies, emitting alpha particles. Because the potential health problems are better understood today than ten years ago, and because the Nuclear Regulatory Commission (NRC) has developed increasingly stringent government regulations, the uranium mining industry applies a high level of technology to the disposal of nuclear wastes. In most cases, low-level radioactive wastes are disposed of at or near the site where they are produced. There are six commercial burial grounds for low-level wastes, but it would not be economical to ship all mine or milling wastes to these sites. The on-site disposal methods most often used are ponding

Jan 1, 1979

By Coolbaugh, Franklin

CRUSHING of Climax mine-run ore is carried out in two plants: No. 1 plant (flowsheet in Fig. 1) has a capacity of approximately 5000 tons per day. It is used as a stand-by except when maximum production is required. No. 2 plant (Fig. 2) has a top capacity of approximately 17,000 tons per day. The No. 2 crusher is more efficient to operate on reduced tonnages regardless of the wide variation in peak capacities. The system of crushing is similar in both plants: Mine ore, of a size which can be drawn through 48 by 96-in. slusher openings underground, is dumped into the crusher bins from ten-ton mine cars and fed into 48 by 60-in. Buchanan jaw crushers by means of chutes and Ross chain feeders. The jaw crushers are set to discharge at approximately 9-in. size. Jaw crusher discharge is conveyed to 7-ft. Symons standard cone crushers where it is broken to minus-2-in. size,

Jan 1, 1946

By A. S. Nowick, E. S. Machlin

ONE of the main criteria used to rate the heat-resisting properties of alloys is stress rupture.1 During a stress-rupture test a tensile specimen is held under a constant load at a constant temperature until it fractures. The chief measurement made during this test is the time required for rupture at the specific test stress and temperature. It was found empirically from a series of stress-rupture tests at a constant temperature that when the logarithm of the time for rupture is plotted against the logarithm of stress a straight line is obtained within experimental error.2~3 This method of showing stress-rupture data has been adopted by many investigators and the KACA.4 By interpolation and extrapolation from these plots, values of the stresses required to rupture the specimens (the rupture strengths) in 10, 100, and 1000 hr are obtained for specific temperatures. Alloys are then rated for a particular application on the basis of their rupture strengths at the rupture life that most nearly represents the application. Inasmuch as stress rupture is an important criterion in rating heat-resisting alloys, it would be advantageous to know the quantitative dependence of the time for rupture on stress, temperature, com- position, and structure. In order to obtain this information, an investigation was made at the KACA Cleveland laboratory during the spring of 1945. The theory of rate processes was used because it has been found to apply to certain processes such as chemical reactions, viscous flow, and creep that occur at a definite rate for given conditions. It was thought that stress rupture was such a process. An equation was derived that gives, for a given com- position and structure, the dependence of the time for rupture on stress and temperature. The investigation is part of a general program to provide information that will lead ultimately to the development of better alloys in order that the efficiency and power output of gas turbines used in aircraft propulsion can be increased. THEORY The theory of rate processes will first be discussed as a general theory. It will then be shown that if stress rupture of heat-resisting alloys can be treated as a rate process, certain equations must be satisfied. Later sections will then show that these equations are satisfied. General Theory of Rate Processes The theory of rate processes5 eveloped by Eyring and others has been applied to chemical reactions as well as to other processes such as viscosity of liquids and diffusion. In every case in which rate- process theory can be applied, there is a small subdivision, so that the macroscopic process is the net effect of all the small processes. This smallest subdivision is called the "unit process.'' For example, in a chemical reaction the unit process is

Jan 1, 1947

By Winston W. Spencer

ALTHOUGH by far the largest A consumer of platinum metals in the world, the United States until recently has been in- significant as a producer. Writing in the "Minerals Yearbook" for 1939, H. W. Davis states that 1938 probably marked the beginning of an- other period of transition in the world production of the platinum metals. In that year, he says, their production in the United States jumped to 49,380 oz., or fourth in the rank of world output. In the ten-year period 1925 to 1934 United States output ,averaged only 8300 oz. Practically all of this sudden in- crease in production is attributable to the introduction of mechanized equipment at the placer deposits in the Goodnews Bay district of Alaska. This district adjoins the Bering Sea and Kuskokwim Bay (accented on the first syllable), and is approximately 120 miles south of the mouth of the Kuskokwim River. The nearest village and post office is Platinum, which lies about eleven miles north- east of the Goodnews Bay Mining Company's camp. A good gravel road connects the mine camp and the village.

Jan 1, 1940

By Peter J. Conroy, Julianne H. Gyarmaty

INTRODUCTION The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. The contract includes monitoring of two adjacent longwall panels. This paper summarizes the surface monitoring work that was performed through February of 1982. Mining of the first of the two panels (3 off 3 north) was completed on February 3, 1982. Results of the surface monitoring through completion of this panel are presented and discussed. SITE DESCRIPTION The mine being studied is located in eastern Ohio. The site is west of the Ohio River, approximately 56 km (35 miles) south of Wheeling, West Virginia. The topography of the unglaciated region

Jan 1, 1982

By L. Adler

The author recently proposed a technique for handling the effect of planes of weakness on failure in geologic material.1 The technique employed an "extended" Mohr's rupture envelope, on which was superimposed a generalized three dimensional stress representation. Subsequently, the method was applied to so-called two-dimensional stress states" which were in reality degenerate three-dimensional ones. Since a two-dimensional stress solution usually refers to a plane stress condition, the terminology was confusing. The distinction between a plane stress state and a degenerate three-dimensional one is shown in Fig. 1. The solution of problems involving a generalized three-dimensional stress state is greatly aided by continual reference to the basic principle that no stress components can act on a plane, oriented as is the weakness plane, which lies outside of the weakness plane's rupture enVelope.2 This is shown in Fig. 2; and if it is also remembered that the radii of the Mohr's Circles give the orientation of such a plane, solutions are easier to follow, and perform. Sample Problem 1: Site Location (generalized three-dimensional case).' Given: 1) Both rupture envelope for the solid and plane of weakness. 2) Existing principal stresses and orientations in space (?12, ?13) obtained from a stress analysis of the proposed structure. Find: Permissible orientations of the weakness plane in order to select a suitable site.

Jan 1, 1963

By H. C. Johnson, J. K. Elliott

One of the primary requirements for successful operation of an enriched gas-drive project is to control the composition of injection gas. This can become a serious and difficult problem, particularly in cases where the enrichment material is being furnished from a number of field -produced gas streams. It is possible to effect control of the injection gas composition through frequent or continuous sampling; however, this can be extremely costly and, in many cases, impractical due to laboratory requirements of time. Another alternative would be to provide a calculation technique which would be flexible and sufficiently accurate to predict composition of the liquid and gas streams of interest at any point in the system. The purpose of this paper is to discuss a technique that was used successfully on an operating enriched gas-drive project for developing information which could be used for controlling composition of the injected gas. FIELD OPERATIONS The particular field (hereafter called Example field) in the example operation being discussed is composed of four oil reservoirs (A. B, C and E) and one gas condensate reservoir (D). Casinghead gas from the oil reservoirs and gas from the gas condensate reservoir are gathered through a field gathering system as shown in Fig. I for injection into Reservoir C. The gas mixture which is recovered from the five reservoirs for injection purposes is composed of gases liberated in 19 individual separators, each operating at a separate temperature and pressure. PROPOSED CALCULATION TECHNIQUE It is well known that vapor-liquid equilibrium calculations in general use throughout the petroleum industry can be used to predict reliably the phase behavior of hydrocarbon mixtures, particularly at pressures less than 1,000 psig. It is then a simple matter to account for the material on a ComPonent basis by m''ing flash and material balance calculations at each separation point in a hydrocarbon system. Accordingly, it was proposed to use vapor-liquid equilibrium and material balance cal- culations with a medium-sized electronic digital computer as a basis for developing a control procedure for use in controlling injection gas composition in the enriched gas-drive project. Although the approach is a simple one, the numerous vapor-liquid equilibrium calculations involved make the problem laborious; in this particular case, it would have been impractical to make sutficiently complete analysis without the aid of digital computing equipment. SAMPLING AND VERIFICATION OF CALCULATION PROCEDURE To obtain representative gas and liquid stream samples and to provide a quantitative measure of overall system Performance for comDarative purpLses, a thorough test of the field and plant system was conducted in the summer of 1957. Oil production at each battery was sta-