Search Documents

The members of the Institute living in the lower Mississippi Valley, I extend a hearty and cordial invitation to their fellow-members to meet with them nest October, in St. Louis. They believe that it will be a meeting of singular interest, inasmuch as the district in question can show in active production almost all of the more useful metals and non-metals. Perhaps too few know that the Southeast Missouri District, about 80 miles south of St,. Louis, and to which a special trip is planned, is the largest lead district in the world. It was that before-the European war, and, now that the production of lead has greatly increased abroad, and has correspondingly increased in the United States, this is one of the most interesting of all lend districts. In 1913, the production of the world was 1,270,000 tons, the last world figures obtainable. In that same year the production of the United States

Jan 5, 1917

By J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation, sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher. The

Jan 1, 1976

By Donald A. Brobst

The minerals barite (BaSO4) and witherite (BaCO3) are the chief sources of the element barium and its compounds needed for many industrial processes and products. Barite, the principal ore mineral, is found the world over and is abundant and widely distributed throughout the United States.3 Witherite is much less common than barite, though more desirable in many ways as a raw material for the production of barium chemicals. England is the chief producer of witherite. Witherite is not mined in the United States at the present time, but it has been mined with barite from a deposit at El Portal, California. Barite is also called barytes, tiff, cawk, or heavy spar. Ordinarily it is a heavy mineral that crystallizes in the orthorhombic system. It is colorless, white, or gray, and transparent to opaque. In some deposits barite is black, yellow, brown, red, green, or blue because of included impurities. The streak is white and the luster vitreous to resinous or pearly. The specific gravity of pure barite (65.7 pct BaO and 34.3 pct SO3) is calculated to be 4.5, but inclusions and impurities in natural barite may reduce this value considerably. Well-formed crystals are generally tabular and have three cleavages. The barite of many deposits, however, has an uneven fracture and an apparent cleavage caused by separation along planes between successively deposited layers. The hardness is 2.5 to 3.5 on Mohs' scale. Commercially the terms "hard" and "soft" are used to refer to ease of grinding. Barite is relatively insoluble in water and acid, and thus can be used as a chemically inert material. Witherite, the natural carbonate of barium (77.7 pct BaO and 22.3 pct CO2), crystallizes in the orthorhombic system. The fracture is uneven and the luster is vitreous to resinous. The hardness is 3 to 3.5. The specific gravity of the pure mineral is calculated to be 4.29. It is transparent to opaque. The color is ordinarily white, gray, yellow, brown, or green. Geology and Distribution of Deposits Workable deposits of barite are widely distributed throughout the world in many geologic environments in sedimentary, igneous, and metamorphic rocks. Most deposits can be classified into three main types: (1) vein and cavityfilling deposits; (2) bedded deposits; and (3) residual deposits. 1. Vein and cavity-filling deposits are those in which barite and associated minerals occur along faults, gashes, joints, and bedding planes, and in breccia zones and solution channels. They also occur in various collapse and sink structures in limestone. Sharp contacts of the veins and cavity fillings with wall rocks are common. Barite cements fault and collapse breccia by replacement of the matrix or by filling voids. Large-scale replacement of the wall rocks beyond ore-controlling structures is rare. Barite in vein and cavity filling deposits is generally dense, "hard," and white to gray. Associated minerals are fluorite, calcite, ankerite, dolomite, quartz, and many sulfide minerals, especially pyrite, chalcopyrite, galena, and sphalerite. Gold, silver, and rare earth minerals occur with barite in some deposits in the western United States. Barite is also a gangue mineral in metallic ore deposits but production as a byproduct from such deposits will be affected by many economic factors. The host rocks are igneous, sedimentary, and metamorphic rocks of pre-Cambrian to

Jan 1, 1960

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose moulding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956, p. 15). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat, abrasion, corrosion, and oxidation-resistant, and high strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, :hemica1 process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present economic-political conditions, he U.S. and for that matter, North America, has virtually insignificant ore reserves of chromite. There are chromite deposits, as will be described, but they would only be used under highly abnormal conditions if all outside sources were cut off. All chromite used in the U.S. is imported from the eastern hemisphere in which are contained the principal world reserves. As the main suppliers in 1971-72 were the USSR, Turkey, Republic of South Africa, Philippines, and Rhodesia, the strategic nature of chromite is obvious.

Jan 1, 1975

By D. A. Farmen

INTRODUCTION In early 1978, engineering personnel at The Carter Mining Company began using photogrammetry coupled with a computer modeling technique to aid in mine planning efforts. The decision to develop this approach was based on the following needs: 1. A method to accurately capture excavated quantities for reporting purposes, 2. A method to produce accurate up-to-date maps for planning purposes, and 3. A computer-based mine-planning technique that would be compatible with techniques used in the past. The system developed utilizes a photogrammetric contractor to provide thousands of aerially-surveyed data points for input into the computer system. Each month the Rawhide and Caballo mines are flown by the photogrammetric contractor. The terrain of the active pit area is digitized and punched out on computer cards. This information is read into The Carter Mining Company's computer facilities, and an updated two-dimensional topographic grid model of the pit is generated. This surface is used to generate quantities moved during the month, to update isopachs, and to update quantities contained in fixed block progression polygons used for forecasting purposes. The system has greatly reduced the amount of manhours spent in field surveying and provides a useful tool for expeditiously evaluating many different forecast cases. It also provides the

Jan 1, 1983

By T. L. Fritzlen

EXTRUSION of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact' that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relationship between the temperature of the material being extruded and the pressure required to extrude. According to Schishokin,2 this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. CHARACTERISTICS OF THE EQUIPMENT The capacity of the press determines the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1945

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By John V. Beall, William F. Haddon

A long the mighty Andean Cordillera, there is splendor beyond imagination-in the natural beauty of the mountains and in daring engineering and lavish investment in the mines. This is the story of the great copper mines of Chile and Peru. Each mine has a special quality which has tested the physical and spiritual resources of the founder. In the early days of the older mines, the mining engineer of song and story was more the rule than the exception. He was physically tough, ingenious and a leader of men. In the current political and social environment of Chile and Peru, the foreign contract mining engineer is still needed; but he must be a different type of man. To John J. Selters at Cerro's Rio Blanco, the principal ingredient is still "toughness," but it is "toughness of mind" that is needed. "He probably should be a teacher." The copper mines are not new. They were, almost without exception, worked by Indians (La Exotica might prove the rule), and later by the intrepid Spaniards. Modern mining began after the turn of the century. In Chile, the first of the big ones was the Braden Copper Co. founded on the El Teniente deposit. This development was followed by Chile Exploration Co. at Chuquicamata and Andes Copper at Potrerillos. These properties have been developed over the years by vast expenditures of money and a monumental amount of labor. None was free of technical problems-metallurgy at Chuqui, marginal grade of the old mine at Andes, avalanches and the great fire at El Teniente. The evolution which has brought the established mines of Chile, and the new ones coming on stream, to their present state of development is in reality the work of wonders of input-money, engineering and responsible management in an atmosphere of political stability. Without any one of these, the result would have been failure.

Jan 11, 1969

By W. R. Johnson

In the spring of 1935 the writers undertook to compare the geomagnetic and direct-current earth-resistivity methods of tracing a concealed dike along its strike. As far as they are aware no such direct test has been attempted.# The area surveyed lies along United States Highway number 15 about one and one-half miles east of Chapel Hill, North Carolina, and northeast of Bolin Creek (Fig, 1). To the south of the highway is the flood plain of Bolin Crook, and to the north is a hill that rises almost to the elevation of Chapel Hill. A diabase dike, which strikes slightly west of north, out-crops in a. gully just south of the highway. Southward it has been covered by alluvium but northward outcrops again on the southeastern slope of the hill north of the highway. South of the highway the country rock is Triassic shale and sandstone, the northern limit of which is slightly north of the road. On the Geological Map of the United States I the pre-Triassic formations are shown as lower Glenarm and assigned a pre-Cambrian age. Since the ago of the Glenarm has been called into question in Pennsylvania 2, the writers prefer not to commit themselves as to the ago of these rocks further than to say that they are definitely pre-Triassic.

Jan 1, 1937

By M. E. Gershon

A mixed-integer formulation of the mine scheduling problem is discussed and applied for the purpose of optimizing both the mine production sequencing and the mill blending and processing problem simultaneously. Previous attempts at solving these problem separately, although successful, fail to take into account the interrelationships between these problems. Project structure selves as the outline of this paper Generalized in its organization, this concept is useful for long, intermediate, and short range scheduling. Actual applications that show the concept also is applicable to mining a variety of ore are mentioned.

Jan 1, 1984

By William Phillips

THE earliest mention of the sulphur deposits in what is now Culberson County, Texas, seems to be contained in "Explorations and Surveys for a Railroad Route from the Mississippi River to the Pacific Ocean, United States War Department, 1853-54." Captain John Pope (he was not commissioned Captain until 1856) had charge of one of the divisions of the Survey. In his report on the geology of the route, William P. Blake noted the analysis of a greenish earthy powder from the bed of Delaware Creek, at the springs, which contained 18.28 per cent. of free sulphur. The report states: "From the chemical examination of the waters of the spring, by Dr. Booth, it appears that chloride of sodium is the principal solid ingredient, but considerable quantities of sulphide of sodium are present. * * * * * The waters from the springs examined by Dr. Booth were alkaline, but it is possible that some of the springs are acid; and in this case the precipitation of sulphur would ensue on the mixture of the acid waters with those charged with alkaline sulphurets and the origin of the deposits of sulphur would he thus explained." This is the first reference to the existence of sulphur in that region, the first mention of the character of the water found there and the first suggestion as to the' origin of the deposits. The possibility of the existence of acid waters was confirmed by E. M. Skeats, nearly 50 years later.1 In this publication, Skeats says that the water from the sulphur deposits in Section 11, Block 114,, Township 5, contains 79.08 grains of free sulphuric acid per gallon. This locality is about 13 miles (21 km.) south of Delaware Creek and about 35-miles (56 km.) east of the Delaware Springs. The next published reference to the existence of sulphur in Trans-Pecos Texas is in the First. Annual Report of the Geological Survey of Texas, 1889, page 226, where W. H. von Streeruwitz mentions that sulphur is found in that region, but gives no further information. In the

Jan 9, 1917

By Howard Willey

Mining operations of the Charcas unit at present are limited to the Tiro General mine at Charcas, in the State of san Luis Potosi, Mexico. The Tiro General mine was first operated during the Spanish occupation of Mexico for rich silver ores in an oxidized zone along the outcrop of the principal vein. In depth the ore is a complex sulfide with widely varying proportions of sphalerite, argentiferous galena and chalcopyrite ; and until recent years, it was economically impossible to carry on mining otherwise than irregularly in sections of the veins richest in galena and chalcopyrite. The advent of selective flotation brought the orebody as a whole within the field of economic interest, and a flotation mill of 650 metric tons daily capacity was constructed in the year 1925. The mining of partly worked-out sections of the mine, as well as the very heavy ground in most of the stopes opened in virgin ore, presented an unusually difficult problem. This paper describes the so-called "filled top slice" stoping method finally adopted as the standard system. Physical and Geological Conditions The principal orebody of the mine is an oreshoot about 1400 ft ng in a fissure vein striking about east and west and with an average lip of 70" to the north. The footwall of the orebody is fairly cleancu and regular both longitudinally and vertically and generally shows a dell-marked post-mineral slip. The footwall rock varies from a fairly strong limestone to a broken, metamorphosed limestone which requires heavy timbering. In some sections it is an altered, crumbly porphyry, which swells badly and necessitates frequent renewal of drift and raise tirnber. The hanging wall is irregular and frequently an assay wall. The stopina width ranges from a few feet up to more than 90 ft.; it averages about 30 ft. For the most part the hanging-wall rock is a shattered and altered monzonite porphyry, nearly aways requiring heavy timbering. The orebody is greatly fractured by post-mineral movement, which usually followed the footwall and left it as a smooth surface frequently covered with a slippery clay gouge. Two well marked transverse faults

Jan 1, 1931

By Owen F. Devereux

Two discrete types of microstructure me seen in cermets formed by the reaction: 4Al (liquid) + 3SiO2 (glass) — 2A12O3(a) + 3Si (solid) Relatively coarse-grained macroscopically isotropic specimens resulted from reaction with aluminum containing appreciable silicon, while macroscopically anisotropic fine-grained specimens were formed by reaction with aluminum low in silicon. Optical microscopy, electron microscopy, and X-ray diffraction suggest that the anisotropic material contains gross areas in which submicroscopic grains of a A12O3 are oriented along radial lines drawn from the specimen surface. These lines are presumed to originate at defects in an otherwise protecting surface layer. A unique cermet is formed by the reduction of high-silica glass by molten aluminum according to the reaction: 4A1 (liquid) + 3SiO2 (glass) — 2A12O3 (a) + 3Si (solid) The free-energy change accompanying this reaction is -150 kcal at 800°C; the volume change (volume of A12O3 and silicon minus volume of SiO2) is +6 pct. The reaction product, however, contains aluminum metal as well as Al2O3 and silicon because some of the product silicon is dissolved in the aluminum bath and is replaced by aluminum in the structure. The product is a hard gray solid that retains the external dimensions of the original silica article. The system has been studied in the past, the investigations culminating in patents to George1, 2 and Saw-chuk., The former emphasize that this reaction is but one of a relatively broad class of such systems, while the latter demonstrates that a marked improvement in the gross physical properties of the cermet can be obtained by dissolving appreciable quantities of silicon in the aluminum reactant. The system has also been studied by workers at Rolls Royce Ltd.,4-6 who have patented the addition of small quantities of arsenic, antimony, bismuth, or phosphorus to the reactant bath to SO impede the reaction that glass fibers may be metal-coated by immersion in molten aluminum.

Jan 1, 1969

By H. Y. Yancey, B. M. Bird

One of the problems studied by the U. S. Bureau of Mines in cooperation with the University of Washington has been the re-treatment of table middlings. Hydraulic classification has given the best results. Instead of using the classifier to prepare the feed to the tables, as has been the practice for many years in ore dressing, it is used to separate part of a middling product that cannot be re-treated successfully on the table. Middlings are desirable in a table plant because the separation according to specific gravity is incomplete; that is, in the products of the table there is always an overlapping of free particles of coal and refuse that can be distinguished with heavy liquids such as are used in the float-and-sink test. The causes of this overlapping may be divided into two groups, those outside the table separation itself and those inherent in the table separation. The first of these groups includes, among other causes, the following: (1) poor adjustments of the table, (2) overloading or underloading the table, (3) irregularities in the quantity and quality of the feed, (4) irregularities in the power and water supply, and (5) a vertical dancing motion of the table deck due to weak foundations. These causes of overlapping are largely unnecessary in a properly designed and constructed plant; but whenever they are present they materially affect the character of the middling product, and hence the problem of re-treatment. The other group includes three additional causes: (6) small differences in specific gravity between coal and impurities, (7) a size-specific-gravity relationship of the coal and refuse particles in the table feed such that the sizing action of the table opposes the separation according to the specific gravity, and (8) shapes of particles that prevent a separation. The sixth, small differences in specific gravity, may be a very important reason for an incomplete separation. The change in specific gravity from coal to shale is always gradual and the designation of one part as coal and another part as refuse is arbitrary. If some specific gravity, such as 1.45, is chosen as the dividing point between washed coal and refuse,

Jan 1, 1930

By Thomas M. Drown

THE means relied on to attain uniformity in Bessemer steel may be enumerated as follows I. The appearance of the flame. II. The appearance of the slag. III. The spectrum of the flame. IV. Examination of the steel itself. At present, I wish briefly to bring forward a few considerations with reference to the last two mentioned, namely, the conditions favoring the employment of the spectroscope and examination of the steel. From the amount of careful investigation which has been devoted to the examination of the Bessemer flame by the spectroscope, both on the part of scientists and practical metallurgists, one might reasonably expect some results definite and satisfactory in their nature, first, as regards the nature of the flame, and second, as to the practical value of the spectroscope as a guide in conducting the process. We find, in fact, however, that uncertainty and confusion still exist. In Germany, where this subject has received the greatest attention, it is now very generally conceded that manganese is the cause of the well-known groups of dark bands that characterize the Bessemer spectrum. Nor is it easy to see how we can avoid accepting this conclusion, when Wedding and Von Lichtenfels have produced the manganese spectrum and found it to correspond closely with that shown by the Bessemer flame. But it is evident, on a moment's reflection, as Roscoe has recently brought forward, that manganese cannot be the only cause of the Bessemer spectrum, for we notice the characteristic bands quite as

Jan 1, 1873

By W. T. Allan

RAW bituminous coal has been in general use as a blast-furnace fuel in Scotland for the last century, and although its use has now been largely abandoned and it has been replaced by coke in the majority of the few furnaces which are at, present in blast in this country, coal-smelted pig iron is not yet a thing of the past; it is still being produced and mar-keted in competition with the more cheaply smelted product of the coke-fired furnace. Various factors have influenced this change in practice; the once plentiful deposits of coal of a suitable nature for the blast furnace are now not so easily obtainable; native blackband and clayband ironstones which are easily smelted in the coal-fired blast furnace, although still far from being exhausted, are not available except at a. cost that is somewhat higher than that of imported ores, making them unattractive to the ironmaster that is compelled by circumstances to smelt his iron at the lowest possible cost. Within the last 15 years overproduction of synthetic nitrogen has led to progressive reductions in the price of sulphate of ammonia, the recovery of which together with the other by-products before that time materially assisted in reducing the working costs of the coal-fired furnace. Now the sale of the by-products recovered yields a diminished profit. When the cost of the product is the only consideration the small, slow-smelting, coal-fired blast furnace cannot compare with its large, modern, coke-fired competitor. Other `considerations do not by any means all support the same side of the argument. In the smelting of pig iron to be used in the manufacture of steel where the quality of the final product depends so largely upon the control of the conversion process and so much less upon the physical quality of the pig iron used, the physical properties of the pig iron do not exert any appreciable influence upon the quality of the steel produced, therefore the methods employed in the smelting of the pig iron matter but little so long as the requisite chemical composi-tion is reached. On the other hand, in ironfounding where the simple melting of the pig iron, which is the only treatment it receives before being cast into its final form, does little or nothing to modify its original charac-

Jan 1, 1937

By Charles N. Bell

The Telluride mining district of southwestern Colorado is defined by the 37" 45' and 38" parallels of latitude and 107" 45' and 108" meridians of longitude. Telluride was never a boom camp, but has had a steady growth. In recent years, notwithstanding the business depression of 1920, the business has been the same as in normal years. The first prospector is said to have appeared in 1875, in which year locations on the Smuggler vein were made. Shipments were made in 1877 and 1878, and in 1879 milling the ores was attempted. While the district produced high-grade ores, it did not become important until 1890, when the Rio Grande Southern R. R. was completed from Ridgway to Telluride. The railroad has since been extended to Durango. In the fall of 1896, 400 stamps were in operation, and the annual production was $3,000,000.00, two-thirds of which was gold. The total production from 1875 to 1923 was: gold $58,274,527; silver 41,-830,920 oz., valued at $31,016,893; copper 15,258,866 lb., valued at $2,533,291; lead 166,056,484 Ib., valued at $8,324,910; zinc 18,141,182 Ib. valued at $1,323,787; or a total production of $101,473,408. All claims are held in fee. Most of them are 1500 by 300 ft. but claims located within the last few years are 1500 by 600 ft. General supplies are obtained at Telluride, Denver, and Salt Lake. The largest mines are within 6 miles of the town of Telluride. Denver is 422 miles and Salt Lake is 439 miles, by rail, from Telluride. One-half of the distance to Denver and one-sixth of the distance from Telluride to Salt Lake is by narrow-gage railroad. The labor is efficient. The best miners are Italians and Austrians, then Slavs, Greeks, and Mexicans follow in the order mentioned. There are no labor unions. There are no serious mine pumping problems, the drainage being through adits. The Tomboy and Smuggler companies pump water from their reservoirs, the former for milling and domestic purposes and the latter for milling, power, and domestic purposes. BIBLIOGRAPHY A partial bibliography of the Telluride District is: Geologic Atlas Telluride No. 57; Preliminary Report on the Mining Industries of the

Jan 1, 1925

By W. J. Reagan

THE problem of increasing output and decreasing percentage of rejections is a vital one in the manufacture of steel of any kind. The making of basic open-hearth steel for use in rolled steel wheels, tires for locomotive and car wheels, and forgings of various kinds, is a highly specialized industry. The increase in weight of railway rolling stock of all kinds, and the high speed that the public demands of transportation facilities, make it imperative that steel for use in this class of material shall be of the highest quality obtainable. During the past few years it has been the writer's good fortune to have opportunity-to study the defects in basic open-hearth steel, and also the results obtained by various changes in open-hearth practice, on such defects. The opportunity for study and the details available are rarely found in the manufacture of steel of any kind. It seems reasonable to assume that many of the results determined here can be applied to the production of steel of other types with a decided improvement in quality, a decrease in the percentage of rejections and an increase in output. All of the material described is basic open-hearth steel with the following range of analysis: carbon, 0.50 to 0.85 per cent.; phosphorus and sulfur, 0.04 coax.; silicon, 0.15 to 0.35; manganese, 0.50 to 0.75. All of this material is bottom-cast, therefore tapping and pouring temperatures are higher than in top-cast production. Ingots used in this type of work are of standard length with varying diameters. The ingot is known as duodecagonal, or twelve-sided. The standard body length is 88 in. and the hot top length, 14 in. Fig. 1 shows a typical ingot of this type. The diameter varies from 13 to 30 in. Ingots for special forgings, which cannot be made in molds of standard size, are made in molds of various sizes and designs. These ingots are sliced cold, into blocks of various lengths, depending upon the weight of the forging to be made. Fig. 2 shows the ingot-after coming from the slicing lathe. Just sufficient metal remains between blocks to hold the ingot in one piece while it is being removed from the lathe; then steel wedges are inserted between the blocks and the blocks are broken apart. This affords abundant opportunity for inspection, as the interior of the

Jan 1, 1930

By R. P. McLaughlin

In most branches of the mining industry it is a well-recognized fact that care must be taken to protect the mineral deposit from undue physical injury. It is comparatively easy to grasp this idea when the mineral is a solid and the lives of workmen depend directly upon the care with which it is removed from its natural position, but when the product is a liquid drawn up from pools several thousand feet beneath the surface of the ground through openings only a few inches in diameter, it requires some imagination to picture underground conditions and the changes which must often occur. The development of the petroleum deposits of California has been attended by numerous accidents, the results of which are readily noticed at the top of the wells and in the profit and loss accounts of the operators. Determination of the cause of these accidents has been the subject of considerable study, which naturally has fallen upon men familiar with technical methods. The greatest damage to the oil deposits of California has resulted from water finding its way into the oil-bearing sands, and it is the purpose of this paper to set forth briefly this phase of the oil industry. Much of the material here presented has previously appeared in publications issued by the California State Mining Bureau, which, under the direction of State Mineralogist Fletcher McN. Hamilton, has investigated the subject and taken steps toward improvement of conditions. The writer, having been in charge of this branch of the Bureau work, has gained considerable knowledge of existing conditions. Generally speaking, the oil-bearing formations of California are soft, unconsolidated sand beds, separated by clay strata, which are also soft. Some of the sand beds carry water instead of oil. All of the beds are more or less separated, probably being of lenticular shape. Very few of the beds in the oil fields lie flat or undisturbed over any great area. Folding and tilting are common, and faulting also occurs in some of the fields. The accumulation of oil is not confined to any single structural feature, such as the anticline, but occurs in many other structural features. Water-bearing strata occur in practically every oil field in the State. Complete data are not at hand for a comparison of the damage

Jan 1, 1916