Search Documents

By B. P. Mulcahy

When the phrase "selection of coal for carbonization" is used, there is always the implied continuance of thought "to make good coke.'' The reason for this, of course, lies in the fact that, in almost all instances, when coal is carbonized coke is the principal product. Under certain conditions the yield of gas may also be a factor, but even here it must be secondary to the coke yield, for in every instance coke represents the largest single product of the process. The importance of coke to the byproduct industry has been considerably enhanced during the past 20 years because of the continuously decreasing financial returns of all the by-products. This fact will account, in part, for the rebirth of interest and investigation in the carbonization process during the past 10 years. Many papers have been written on this subject, with naturally divergent thoughts because of the diversity of interests, but in each instance the common aim was the same—the making of better coke. Scope of Investigation In perusing this literature, the writer was struck with the constantly recurring imposed condition of asking for better coke, but with the distinct unwillingness to make any concession to temperature of carbonization. When there is a high demand for coke, the only means by which the industry can increase the quantity is to shorten the coking time by an increase in temperature, or to increase the quantity of low-volatile coal, or both; and since in many instances the percentage of low-volatile coal can be increased only in small quantities, because of factors to be discussed later, the big increase must come from shortening the coking time. When this is done most of the improvement accomplished by the selection of the coals in the mixture is lost. It is not felt necessary in this paper to discuss the advantages of minimum ash and sulphur and other materials in coal. The value of minimum contents of these materials in coke is well established. When the use of coals high in these contents is dictated, the selection of coals, as we will consider it here, cannot apply to full advantage. The scope of this paper, then, will be to discuss the factors of inherent coal characteristics and operating procedures that influence coke quality, for they are fundamentally related and both must be considered if we are to attain our objective of better coke. A study of either must embrace a study of both simultaneously. To properly evaluate the influence of the coal and to help in the selection, we must first be able to appraise the coke, and interpret fairly the influence of the process in all of its aspects. Appraisal of Coke To refer simply to the quality of coke gives no indication of what is meant, for the term is too general in its implication. An analysis of a coke is divided usually

Jan 1, 1944

By Forbes Rickard

Gilpin County, the cradle of mining in Colorado and the Cornwall of North America, is too well known to need much introduction; get, for the benefit of those not familiar with the district, it may be well to premise that it comprises a tract of country of about 122 square miles, lying between the counties of Jefferson, Boulder and Clear Creek, and hounded on the west by the main range of the Colorado Rockies. It is located centrally in the State, 40 miles west from the city of Denver. During the 38 years since the first gold-discovery, Gilpin county has contributed about eighty million dollars in gold and silver to the world's supply of these metals. Many mining districts have had their rise and decline in half this time; but, very far from being exhausted, this mining district is still in the ascendant; its output is increasing (it was $3,600,000 for the year just closed), and it was never more prosperous nor productive than to-day. Taken generally, there does not exist anywhere in the world so great a number of permanent veins within so small an area as in this district. Gilpin is practically a " poor man's camp." Its veins, with few exceptions, outcrop at the surface. In the oarlier---days of the camp these outcrops were worked in many instances by sluice-mining; particularly is this the case with regard to the veins of the Russell gulch. Discoveries are still made in the heart of this district, and the productive area is every year extending its limits. The districts of Yankee Hill, Hawkeye and Pine Creek, which used to be isolated, are now part and portion of the one gold-field of Gilpin county. Within the last year sensationally rich gold-discoveries have

Jan 1, 1899

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By H. H. Stoek, G. W. Harries

The term " Anthracite Coal-Field " is generally used to refer to a comparatively small territory lying in the eastern-central part of Pennsylvania. This territory includes about 3,300 sq. miles of area, located chiefly in five counties in which anthracite-mining is the dominant industry. Although an area of 3,300 sq. miles is embraced in the region, less than one-fifth of this area, or only 484 sq. miles, is underlain by workable coal-seams. Moreover, this prorluctive portion is not a continuous area, but consists of a number of detached basins. These are known as the Northern, containing 176 sq. miles; Eastern-Middle, containing 133 sq. miles; Southern, containing 181 sq. miles; and western-Middle,containing 194 sq. miles. From the standpoint of business and trade, the region is divided into three districts, known as (1) the Wyoming, which includes the Northern field and the small Bernice basin; (2) the Lehigh region, which includes all of the Eastern Middle field and that part of the Southern field east of Tamaqua; and (3) the Schuylkill region, which includes the WesL ern-Middle field and that part of the Southern field west of Tamaqua. The relative commercial importance of these districts at the present time is shown by the coal-shipments as given in the following table :

Jan 1, 1904

By D. Harker, E. Epremian

The constitution of the nickel-tungsten system has been studied by a number of investigators, the most recent of which are Ellinger and Sykes.1 On the basis of metallography, electrical resistivity and hardness measurements and some X ray diffraction work, they constructed a consitution diagram (Fig 1). Ellinger and Sykes report a0 for the alpha face-centered cubic phase (nickel saturated with tungsten) as 3.66?.‡ The gamma phase (tungsten saturated with nickel) is given as body-centered cubic, but no value of a. is recorded. At 43 pct tungsten by weight (approximately 20 at. pct) a beta phase is reported, but structure and lattice parameter are not known. Primarily on the basis of metallographic evidence, they conclude that beta is a new phase and rule out the possibility of formation of a superlattice since they- observe a new phase in the microstructure. Grube and Schlecht2 report an ordering reaction in a system similar to the Ni-W (Ni-Mo) and Harker3 has shown that NirMo forms a superlattice upon the pre-existing face-centered cubic lattice of the alpha phase. Elliniger arid Sykes observed a change in the diffraction pattern of a 4.3 pct W alloy upon aging and attributed it to the formation of a new phase. Thus, there appears to be some question as to the character of the beta phase reported by Ellinger and Sykes. The purpose of the present work is to determine precisely the structure and nature of the beta phase in the Ni-w system of X ray diffraction methods. Experimental Procedure One inch diameter ingots of 43.66 pct, 40.15 pct and 34.06 pct .tungsten by weight (19.8, 17.6 and 14.1 at. pct respectively) were melted and cast under vacuum from electrolytic nickel and pure wire filament grade tungsten. The ingots were soaked for 16 hr at 1300°C in a hydrogen atmosphere furnace, then swaged at this temperature and finally drawn to 0.020 in. diam wire. Some of the bar stock was retained in 1/2 in. diam rod for hardness and metallographic studies. Wire samples for diffraction work were sealed in evacuated quartz tubes and subjected to the various solution and aging heat treatments in a hydrogen furnace. X ray photograms were taken in a Debeye-Slierrer camera using copper K radiation filtered by nickel foil. Results X RAY DIFFRACTION The lattice parameters of the alpha and gamma phases at saturation were determined by an X ray photogram of the 19.8 at. pct W alloy after solution heat treatment at a temperature well within the alpha-gamma range above the peritectoid temperature (17 hr at 1150°C—oil quenched). The alpha phase was found to be face-centeted cubic with a. of 3.594 ± 0.001?, while the gamma phase was determined as body-centered cubic with a. of 3.158 ± 0.001?. Exactly the same phases and parameters were ohtained with the 17.6 at. pct W alloy for the same solution heat treatment. Thorough analysis was made of an X ray photogram of a 19.8 at. pct alloy sample in the quenched and aged condition (solution treated 1T hr at

Jan 1, 1950

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By W. A. Forbes

OUR present-day geological surveys show that 36 of our States are underlain with bituminous coal, covering a total area of 496,709 square miles. The North American continent possesses 69 per cent of the world's coal reserves, with the United States alone having an estimated 55 per cent. The American coal reserves, in tons, are calculated to he about 3,500,000,000,000 tons, of which we have exhausted about 1 to 1 1/2 per cent. If this coal were mined at the rate of the 1918 production-a record output of 579;000,000 tons-it would not be depleted for 4,000 years. The more easily accessible and high-grade coals would obviously be consumed much before this; some estimates are 100 years. The natural progress of the nation's industries up to 1910 encouraged on every hand the development of new mines, especially where cheap and easy access to coal measures was coupled with short hauls to the consumer. Over-development resulted, which is perhaps today one of the fundamental causes for the many difficulties faced by the coal industry, which is highly competitive; about 70 per cent of the production cost is labor. Salient statistics for 1930, recently issued by the U. S. Bureau of Mines, follow:

Jan 1, 1932

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By AIME AIME

IT its annual meeting on Oct. 21 and 22, the Engineers' Council for Professional Development announced the selection of J. P. H. Perry. vice-president of the Turner Construction Co. and prominent civil engineer of New York City as its new Chairman. He succeeds C. F. Scott, who becomes Chairman of its Committee on Professional Recognition. S. L. Tyler, Secretary of the American Institute of Chemical Engineers, succeeds A. B. Parsons as ECPD Secretary. R. E. Doherty is Vice-chairman. C. E. Davies remains as Assistant Secretary, as do R. L. Sackett as Chairman of the Committee on Student Selection and Guidance, O. W. Eshhach as Chairman of the Committee on Engineering Training, and Karl T. Compton as Chairman of the Committee on Engineering Schools.

Jan 1, 1938

By Homer W. Riley

ANTHRACITE SMALL power-driven, toothed, cast-iron rolls were used first to break anthracite in 1844. Prior to that time, men with hammers, who stood on perforated cast-iron plates, broke the large lumps into commercial sizes. In order to convert run-of-mine into the various sizes required by the anthracite industry, about 20 million tons must be broken, annually, into smaller sizes. This phase of anthracite preparation is of major importance, because the degradation accompanying reduction in coal sizes should be kept at a minimum. The exclusive use of toothed rolls for that purpose indicates that comminution by rolls is the best solution of the problem. Many improvements have been made in tooth design, but the most important was a reduction of the peripheral speed of the rolls from 1000 to 300 ft. per minute. The higher speed was based upon and approximated the velocity of a falling piece of coal when it entered the rolls, Exhaustive roll tests at the slower speed showed that the same size reduction could be affected with less degradation. The adoption, therefore, of slow-speed, compound geared rolls, especially for breaking the larger sizes, became quite general after 1912. A high-speed roll is shown in Fig. 1 and a slow-speed roll in Fig. 2. Anthracite Crushing Problems.-Crushing anthracite presents the problem of selecting a series of rolls that will produce the greatest percentage of the prepared sizes of nut and over. The size distributions to be expected are shown in Table 1. Coal breaking and crushing practices in anthracite breakers involve the use of equipment for comminuting the following classes of material: 1. Run-of-mine-plus 6 ½ -in. coal. 2. Sized coal-steamboat, broken, egg, stove, nut, and pea. 3. Flat coal--coal that is flat and hence not suitable for the market. 4. Bone--a piece of laminated coal and slate, crushed for the purpose of reclaiming the coal. 5. Breaker refuse, reduced to a size suitable for flushing into a mine for back-filling purposes.

Jan 1, 1950

By Frederic E. Carter

THERE have been many attempts to prove that platinum was known to the ancients, but since no traces of the metal have been found in the relics of early times, it must be concluded that it was not known to them. As far as records go, it was actually first discovered in the 16th century in a Spanish mine on the Pinto River in South America; from which source it received its name of Platina del Pinto (little silver from the Pinto). It was more or less of a rarity and was a subject of interest to a few chemists only, until the year 1822 when the metal was first discovered in Russia. In 1819 there were noticed in the washings of the gold sands of the southern part of the Ural Mountains, grains of a heavy white substance, but it was not until three years later that this substance was found to contain platinum. While at first the amounts of platinum brought from the Urals were meager, prospecting soon disclosed rich deposits extending over a considerable area, and nuggets from 10 to 20 lb. were by no means rare. This discovery assured to chemists an ample supply of platinum for their crucibles, etc. The ore is now found in various parts of the world but the richest deposits are still found in the Ural Mountains. The platinum of commerce is obtained entirely from alluvial deposits at depths varying from 6 to 40 ft. The sand and gravel of former river beds are subjected to a series of screenings and washings to effect the separation of the ore. Actually, probably all gold-bearing gravel beds of the world contain platinum, and it is more than likely that large quantities of platinum ore have been thrown away with the black sand washings from gold placer deposits. This is especially true of the alluvial deposits of the Pacific Coast in California and Oregon. Platinum ore is usually found in the form of rounded or flattened grains of "sand," and occasionally in irregular lumps of the size of peas. Large nuggets are very rare. The ore has a metallic luster and is distinguished by its steel gray color, but shows light gray streak when rubbed on a hard white surface; it has a high specific gravity, 16 to 19; is infusible in the hottest blast furnaces, and insoluble in any single acid. Platinum ore is a complex body consisting of the metal in combination with varying proportions of the other members of the platinum group; iridium,

Jan 1, 1928

By Robert H. Merrill, David W. Wisecarver, Raymond M. Stateham

The US. Bureau of Mines, in cooperation with US. Borax and Chemical Corp. and Kennecott Copper Corp., has investigated the use of the microseismic method to evaluate the stability of large, open-pit slope walls. The method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. This report briefly describes the three different types of micro-seismic apparatus, the procedures, and the results of microseismic investigations in the slope walls of the Boron mine near Boron, CaL, and the Kimbley, Liberty, and Tripp-Veteran open-pit mines near Ely, Nev. Microseismic monitoring within a frequency band of SO to 5000 Hz indicates noise rates in stable, inactive mining areas are between 0 and 10 noises per hour; the rates in stable, active mining areas are between 10 and 50 noises per hour; and the rate in unstable areas is as high as 2500 noises per hour. High microseismic noise rates in the Liberty pit correlate with the time of nearby earthquakes, indicating that the earthquakes affected the slope wall. The results provide evidence that the microseismic technique is applicable to large pit walls, and that the wide-band, wide-range microseismic equipment appears to be suitable for open-pit investigations. The microseismic method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. The method has been used for many years to detect incipient failure in roofs or pillars in underground mines. In 1963 the U.S. Bureau of Mines (USBM) started an investigation of the microseismic method in large, open-pit slope walls. The purpose of this investigation was to evaluate the method in open-pit slopes where the rock may be fractured and broken and where the size of the rock mass under investigation is much larger than normally encountered underground. In addition, both the stresses in the rock and the strength of rock near pits are lower than usually found underground. Consequently, there was some doubt concerning the feasibility of the method for open pits, and the economics of such an investigation may have been prohibitive especially if large walls had to be monitored with closely spaced geophones. The successful application of the microseismic method to underground operations has improved safety at little, or no sacrifice, to production or extraction ratios. The anticipated reward in open-pit mining would be the improvement of safety with a minimum sacrifice to mining operations. There is also a possibility that the method could be used to optimize the unloading (stripping) of potential failure areas by the removal of intact rock from the slope wall rather than the cleanup of a slide from the bottom of the pit. This report contains a brief description of three types of microseismic apparatus used in four different pit walls, each of which is different in height, slope, rock types, or has different planes of weaknesses, such as faults, fractures, or joints. Because the geologic features of the pit walls are varied and complex, for brevity, this report dwells mostly on the microseismic apparatus, techniques, the rock noise rates, and the slope movements measured at the various sites. PROGRESS AND DEVELOPMENT The microseismic method was developed over 20 years ago; and the method and examples of investigations in underground mines are summarized by Obert and Duvall. 1 In more recent years, the method has been applied in several underground mines, and an in-situ test under controlled stress conditions is described by Morgan and Merrill. 2 Experience has shown that, on occasions, the microseismic noise rate and amplitude reach a peak value and then start to decrease before a failure occurs in an underground mine; on other occasions, the noise rate steadily increases to a maximum at failure. The method has been applied to slopes by Goodman and Blake,3 and by Paulsen. 4 Goodman and Blake found that the noises corresponded with failures in the slope

Jan 1, 1970

By R. J. Cowan

In the art of cementation a controversy has been going on for years as to whether solid or gaseous carbon is the active agent in carburizing steel. More recently opinion has crystallized into a compromise to the effect that carburizing is a gaseous cementation of steel in the presence of solid carbon. The importance of this theory has a particular bearing upon the work to be described. In the art of carburizing, use is commonly made of such words as '' Catalytic" "atomic," "nascent" and "activated," in an attempt to describe the process. These words are used indiscriminately. For instance, the gas is said to be "catalytic" and carbon to be "nascent," or vice versa. In using these expressions, investigators are confirming the acceptance in their minds of the active conditions of both gas and carbon in the cementation process. Reactions at Metal Surfaces For many years attention has been directed to the consideration of reactions that occur on metal surfaces. When heated under the influence of certain metals a complex gas will be broken down and one of the constituents thereof usually found to be very active chemically in combining with the metal. The process of nitriding is an example of this type of reaction. In this case ammonia (NH3) breaks down at the metal surface and the nitrogen which is thus liberated reacts with the surface to form a nitride whereas molecular nitrogen not so liberated is inert and will not react chemically with the metal. Whatever term or terms may be used to describe such reactions, the fact remains that they are highly important and valuable in their commercial applications. Since the metal surface plays so important a part in these reactions, it is evident that any accumulation of reaction products thereon interferes seriously with the progress of the reactions. For this reason it is desirable to remove all such products as rapidly as they are formed in order to bring active gas into contact with the surface and thus facilitate the desired reactions. This is accomplished best by conducting the operation in a continuous manner, thereby causing the reacting gases to pass over the

Jan 1, 1931

By B. H. Caudle, L. G. Davies, I. H. Silberberg

This paper presents a method of predicting the recovery and performance of a five-spot steam injection project, in which a realistic approach to pattern sweepout efficiencies is made. Published methods for radial systems were modified for the five-spot pattern by approximating the stream lines with straight lines radiating from the injection well and then converging to the producing well. In each radial segment, the position of the steam front and the temperature profile ahead of the steam front were determined by heat balance equations, which included an estimation of heat losses to surrounding formations. The location of the saturations behind the cold water front was determined from a Buckley-Leverett solution to the material balance equation. Results from this program show steamflood recovery in a five-spot pattern to be considerably less than that predicted for true linear or radial flow systems. For a specific reservoir containing 900-cp oil, a steamflood in a purely radial flow system was predicted to recover more than 75 percent of the original oil in place when 2 PV of water had been injected as steam. A five-spot steamflood with otherwise identical properties was predicted to recover 10 percent of the original oil in place when 0.15 PV of water had been injected as steam and to recover almost no oil thereafter. A cold water five-spot flood in this system was predicted to recover approximately W percent of the oil in place with I PV of water injected. For a five-spot pattern in an example reservoir with 10-cp oil, steam injection similarly showed lower ultimate recovery than water injection but no improvement in recovery rule. Introduction The thermal recovery method considered in this study is steam injection in a five-spot pattern. Pattern steam injection has been given little attention in the past, possibly because of some rather obvious disadvantages. Unless steam temperature is maintained throughout the entire swept area, the process will revert to simple waterflood with all heat being lost prior to reaching the oil bank. Also, the oil viscosity reduction takes place near the steam front and not around the producing wellbore, so that low producing rates must still be endured. This is the reason for the success of the steam stimulation, or cyclic injection, in which the fluids are produced from the same well used for injection. On the other hand, steamflooding can offer some advantages. Oil displacement is by four methods: (1) mechanical displacement by the condensed water, (2) viscosity reduction of the crude oil, (3) swelling of the crude oil, and (4) distillation of the crude oil in the steam zone. Although dependent upon the crude, laboratory experiments have shown displacements up to 80 percent by steamflooding. In addition, steam is a good heat transport medium, since it is cheap and has a high heat content. Previous Investigations Previous publications have reported methods for predicting recovery in a steamflood for linear and radial systems. Since no pattern sweep efficiency is taken into consideration, the recovery even from a radial system must be greater than from more realistic geometries such as the very common five-spot patterns. Probably the broadest coverage is given by Willman who reported experimental results and offered a method of predicting recovery for a radial flow system. They concluded that both hot water and steam injection recover more oil than an ordinary waterflood, and that steam injection could yield recoveries "as much as 100 percent greater than by water flood." They also concluded that both the heat requirements for a reservoir and the residual oil remaining in the reservoir after steam injection were independent of the amount of oil originally in place, that short exploitation times were desirable, and that a high percentage of net sand in the reservoir with a high initial oil saturation was desirable. The method assumes that the flood occurs in three concentric cylindrical zones: (1) an inner steam zone, (2) a central hot water zone, and (3) an outer cold waterflood zone. Displacement in the steam zone is based on laboratory-determined residual oil saturations while the hot water and cold water zones use the conventional Buckley-Leverett equations. Although the results shown by Willman et al. are for a radial system flowing out from the well to an assumed external circular boundary, their equations did

Jan 1, 1969

By R. L. Wiegel

The two questions considered in this study are: (1) what similarity is there in the liberation of magnetite from various iron formations, and (2) how is this liberation affected by the size reduction technique employed. Twelve sample suites were obtained from commercial concentrators processing magnetite iron formation in the United States, Canada, and Australia. These samples have grades in the range 15 to 45% magnetite iron and approximate mineral grain sizes o f 50 to 2000 microns. Efforts were directed at measuring the liberation characteristics of the samples obtained from the concentrators primary grinding mills. The Davis tube, a laboratory magnetic separator, was used to concentrate individual size fractions of the size reduction product to determine liberation data. These liberation data were compared with relationships calculated from a highly idealized mathematical model of liberation in a binary mineral system. The results of these comparisons have been encouraging for nine or ten of the twelve samples tested. This leads to the conclusion that for most commercial iron formations, at least with conventional rod mill size reduction, it is possible to quantitatively characterize liberation with two parameters: an effective mineral grain size and ore grade. Limited laboratory size reduction tests as well as one of two sets of liberation data from commercial primary autogenous grinding lend some support to the contention that autogenous grinding can affect mineral liberation.

Jan 1, 1976

By Frederick N. Rhines, William A. Anderson

The investigations of Wymanl have demonstrated that copper deoxidized with several of the commonly used agents that confer immunily to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydrogen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxygen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxidizing anneal, but beyond this the mechanism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subsequently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves be reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the subscale may be complex compounds such, perhaps, as SiO2.Cu2O, which are partially reduced by hydrogen. These possibilities have been examined, and it has been concluded that the first three and possibly the fourth are operative collectively or individually under more or less predictable conditions. Effect OF Precipitated Cuprous Oxide and Dissolved Oxygen The literature provides no definite proof that oxygen in solid solution in copper can confer susceptibility to hydrogen embrittlement; indeed, the research of Leiter2 seemed to indicate the opposite—that to produce the effect, cuprous oxide must be present in massive form and in a more or less continuous network along the grain boundaries. To test this point, pure copper has been annealed in hydrogen under conditions designed to ensure the presence in various samples of: (I) precipitated cuprous oxide, (2) dissolved oxygen only, and (3) no oxygen in any form. Very pure copper" said to contain no oxygen and no spectro-scopically detectable traces of any other element (that is, no individual detectable impurity in quantity greater than 0.0001 per cent) was used. Strips of this material cold.-rolled 75 per cent to 1/8 in. in thickness were subjected to the following treatments, the results of which are noted:

Jan 1, 1941

By Frederick N. Rhines, William A. Anderson

The investigations of Wymanl have demonstrated that copper deoxidized with several of the commonly used agents that confer immunily to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydrogen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxygen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxidizing anneal, but beyond this the mechanism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subsequently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves be reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the subscale may be complex compounds such, perhaps, as SiO2.Cu2O, which are partially reduced by hydrogen. These possibilities have been examined, and it has been concluded that the first three and possibly the fourth are operative collectively or individually under more or less predictable conditions. Effect OF Precipitated Cuprous Oxide and Dissolved Oxygen The literature provides no definite proof that oxygen in solid solution in copper can confer susceptibility to hydrogen embrittlement; indeed, the research of Leiter2 seemed to indicate the opposite—that to produce the effect, cuprous oxide must be present in massive form and in a more or less continuous network along the grain boundaries. To test this point, pure copper has been annealed in hydrogen under conditions designed to ensure the presence in various samples of: (I) precipitated cuprous oxide, (2) dissolved oxygen only, and (3) no oxygen in any form. Very pure copper" said to contain no oxygen and no spectro-scopically detectable traces of any other element (that is, no individual detectable impurity in quantity greater than 0.0001 per cent) was used. Strips of this material cold.-rolled 75 per cent to 1/8 in. in thickness were subjected to the following treatments, the results of which are noted:

Jan 1, 1941