Search Documents

By Qingsheng Liu

A new method of recycling aluminum dross for preparation Al-Si-Ti alloy was studied in this paper. This was carried out in two processes. first the aluminum doss was pretreated by leaching and calcining process, the fine purity and phase of the intermediate oxide powder up to electrolysis demands, then, could be obtained when aluminum dross after washing have been leached for 2h at 100? in 20% hydrochloric acid and calcined for 2h at 1200?, which was treated by cryoite-based molten salt electrolysis. Finally, the Al-Si-Ti alloy was successfully obtained through electrochemical co-deposition in the cathode shows a typical as-cast microstructure. This new recycling method can produce high quality alloy and may bring remarkable economic and social benefits.

Jan 1, 2010

By J. E. Warren, J. H. Hartsock

An asymptotic solution to the equation that describes the flow of a slightly compressible fluid in an infinite porous medium has been used to estimate the interaction between two adjacent wells producing from a common reservoir. A direct method for approximating the interference time defined by Stevens and Thodosl has been suggested. An alternative definition for the time of interference, based on the minimum pressure change in the interference region, has been proposed; also, a direct method of determination has been prescribed. Examples have been employed to illustrate the use of both methods.

By P. Venter, N. Naude

"Coal mining is a thriving industry and 53% of the coal mined in South Africa is used for electricity generation. Mechanization has made coal mining more efficient, but fines generation has subsequently increased. Up to 6% of the run of mine material can report to the -200 µm fraction. Common problems associated with fines handling include dust formation, storage problems, and high moisture levels. A method to turn this material into a saleable product instead of stockpiling it can add value to a company.Briquetting is a pressure agglomeration method where loose material is compacted into a dense mass (FEECO International, 2014). The briquettes must be able to withstand rigorous handling and transport operations without disintegrating. This study aims to investigate the optimum binder and moisture conditions required to produce a mechanically strong briquette using two different binders - a PVA powder (binder A) and a starch powder (binder B).It was found that for binder A the optimum moisture level was 12% to 14%. At this moisture level the greatest compression strength gains were observed, and low amounts of fines produced in impact and abrasion tests. The minimum amount of binder added while still obtaining a strong briquette was 0.5% binder A. For binder B the optimum moisture level was also 12% and the minimum amount of Binder B to be added was found to be 1%. Briquettes that were dried outside reached their peak strength after about four days, whereas the briquettes that dried inside took about 20 days to reach their strength plateau. Hardly any degradation took place on the surface of the binder A film after exposure of 300 hours of artificial weathering. Thermogravimetric analysis confirmed that neither binder A nor binder B will add to the ash content of the coal fines, as both binders totally decompose above 530°C.Binder B yielded stronger briquettes after 15 days and also generated less fines. It is therefore superior to binder A and would be recommended for further use.Paper written on final year project work carried out in partial fulfilment of B.Eng degree in Coal Beneficiation"

Jan 1, 2015

By John C. Machisak

The National Safety Competition is sponsored and conducted annually by the Bureau of Mines, U.S. Department of the Interior, to give greater impetus to the building of programs safeguarding the employees of the mineral industries from disabling work injuries. The results of the 1960 National Safety Competition are presented in this publication. Mines and quarries that were awarded the Sentinels of Safety trophy for the best safety record in their competitive group and those mineral operations that ranked second, third, fourth, and fifth in the competition are listed with a summary of their achievements in preventing disabling work injuries. In addition, this publication presents statistical data on disabling work-injury experience in all other mines and quarries participating in the annual competitions.

Jan 1, 1962

By G. Coetzer

During galena flotation of Rosh Pinah milled material, metal ions and salts contents of various water resources (deionized, simulated circulated, lead concentrate thickener, lead tailing thickener and borehole) influenced mineral recoveries, upgrade ratios, selectivities, froth stability and flotation kinetics. The various water resources employed during galena flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed by the ore, whilst ions associated with gangue minerals (dolomite and quartz) were released into the flotation pulp. Lead concentrate thickener water caused depression of sphalerite and pyrite, increased fast floating fractions for silver, copper minerals, sphalerite and quartz (unwanted), and improved slow floating rate selectivity against pyrite and sphalerite. Lead tailing thickener water enhanced sphalerite recovery during galena flotation (unwanted), and increased fast floating fractions of pyrite. Western borehole water did not affect galena recovery, but sphalerite and pyrite recoveries were unacceptably too high. Ions from copper, lead, and zinc salts tended to release high amounts of ions, such as calcium, magnesium, silicon, and manganese from gangue minerals (dolomite and quartz) during milling. During galena flotation, lead ions depressed sphalerite, pyrite and dolomite at a lead concentration of 400 ppm, but sphalerite was activated at a concentration of 800 ppm. Sphalerite was activated with copper ions (89% recovery, 2.09 upgrade ratio) and depressed with zinc ions (maximum recovery of 25%). This corresponds with findings in previous investigations. Dolomite and quartz were slightly activated with zinc ions. No evidence was found that lead and copper ions activated any gangue minerals during galena flotation. Keywords: galena, water resources, metal ions, activation, depression, selectivity.

Jan 1, 2003

By A. C. Fieldner

THE Bureau of Mines has received many requests for Information concerning the methods its laboratories use for analyzing coal and coke and determining their heating value. The fuel investigations now conducted by the Bureau of Mines are an outgrowth of the work undertaken at the Government coal-testing plant erected in 1904 at the Louisiana Purchase Exposition in St. Louis, and the methods for proximate and ultimate analysis of coal used by the Bureau of Mines are based on those originally adopted by the chemists of the coal-testing plant and followed in the subsequent chemical work of the Government fuel-testing plants at St. Louis, Mo., Norfolk, Va., and Pittsburgh, Pa. The many valuable suggestions and criticisms received from N. W. Lord, director of the School of Mines, and from E. E. Somermeier, professor of metallurgy, of Ohio State University, at that time, are greatly appreciated; development of many of the methods for the proximate and ultimate analysis of coal now used by the Bureau of Mines is chiefly clue to these men.

Jan 1, 1951

This backgrounds the methods, and technical terminology, of digital image processing techniques used to write out remote sensing imagery.

Jan 1, 1983

THE Synthetic Liquid Fuels Act (30 U.S.C., 321-325, and amendments) became law April 5, 1944, and a period of intensive research and development in this field was begun by the Federal Bureau of Mines. As part of this program, bulletins were published on pressure hydrogenation,3 the Fischer-Tropsch synthesis,4 and nil stifle.5 The. Bureau also has published a short bibliography on coal gasification,6 mostly of a theoretical nature. Because anal gasification is prerequisite to either the Fischer-Tropsch or coal-hydrogenation processes, publishing this sizable collection of technical information in this form Will Ire valuable. The material will he presented in three parts. as follows I. United Stares Patents. II. United Kingdom, Australian, Canadian, and South African Patents. III. Other Foreign Patents. Part I appeared in early 1960. Part II follows.

Jan 1, 1962

By P. N. Anyalebechi

The effects of a cross-hatched grooved mold surface topography, casting speed, and superheat on the morphology of solidifying shells of aluminum alloy 3003 have been characterized by a series of immersion tests. The cross-hatched grooves were 0.232 mm deep with wavelength or spacing between 1 mm and 15 mm. The shells solidified at casting speed of less than 10 mm/s on the 1 mm spaced cross-hatched grooved mold surface were fairly uniform with little or no localized variations in thickness. However, the propensity for non-uniform shell growth morphology was exacerbated by an increase in casting speed, melt superheat, and the wavelength of the cross-hatched grooves. This is provisionally attributed to their effects on interfacial heat transfer and wetting of the mold surface by the molten metal.

Jan 1, 2008

This paper contains an account of some creep tests on electrolytic lead and some of its alloys. The stresses used in determining creep were 500, 350, and 200 lb. per sq.' in. The alloys contained silver, bismuth, tellurium, antimony and zinc respectively. All were castin vacuo, and tested "as rolled." Tests were done also on electrolytic lead which had been cast in air.The electrolytic lead contained 0.0005% total impurities.The preparation and vacuum casting of this lead have been described in a previous paper in this series. The preparation of the alloys, and the air casting of the electrolytic lead, are described in the next section.EXPERIMENTAL PROCEDURE.Every effort was made to keep the vacuum-cast specimens from contact with the atmosphere throughout their history.The ingots were stored eIther in a vacuum desiccator or immersed in heavy oil. The creep specimens were coated with vaseline except during rolling, etching and photography, which involved exposure to the atmosphere for about 45 minutes all told.It is not claimed that vaseline is a perfect shield against the intrusion of atmospheric gases. Possibly during the months that some tests were in progress the gases diffused through the vaseline and gained a limited access to the lead.Nevertheless, the use of vaseline gave protection that brought the tests nearer the ideal at which the author aimed, *Research Fellow, Dept. of Metallurgy, University of Melbourne.

Jan 1, 1936

By Stephen R. Iverson, Bill M. Stewart, Michael J. Beus

The U.S. Mine Safety and Health Administration (MSHA) has identified ore pass hazards as a significant safety problem in underground metal mines in the United States injury and fatality data show that many injuries are related to pulling or freeing ore pass chutes and structural failures of control gates and ore pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating these hazards and developing methods to improve safety during transport of ore and waste. Particle flow analysis methods were used to simulate chute and control gate response to various material loading scenarios. Results from computer models indicate that dynamic impacts from ore and waste rock might be considerably greater than theory predicts. Static and dynamic loads were measured in a laboratory setting using scaled ore (sass mock-ups. Field tests were initiated in an active ore pass to determine actual static and dynamic loads. Field data were compared to computer results and indicated that impact and total static loads were substantially less than the computer model results suggested. Damping factors, normal and shear stiffness, and mass frictional characteristics have a significant effect on particle flow and resulting impact loads.

By Davis RA, Wasp EJ, Cowper NT

The transportation of solids by pipeline is not new. In 1891 a United States patent broadly covering a method of pumping coal with water was granted to W. C. Andrews. His pilot plant was constructed on what is now the site of the New- York Public Library in Manhattan. His process was applied to pumping coal mine waste back into the worked out portion of coal mines. On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this 5.0 million dollar installation climaxed three years of development, testing, and construction and proved the Company's faith in pioneering' this unique transportation method for iron ore. This paper will discuss some of the more pertinent items in connection with that three-year period. Also to be discussed will be the operation of this line during the past eleven months.

Jan 1, 1969

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980

By Paul Billingsley

THE purpose of this paper is a comparison, based on genesis, of the ore deposits associated with the igneous rocks of the central Montana Rockies. Considered separately, without attention to their origin, the orebodies appear to be distributed haphazard, with no fundamental laws controlling their position and character. It is believed, however, that if all the factors be weighed, this apparent confusion will to a large degree disappear. The, first essential to such a comparison is detailed knowledge of the individual mines, as to their geographic position (see Fig. 1), their mineralogical character, and in particular the derivation of their ores.1 The authors of this paper have pursued such an investigation for the past 6 years, and have accumulated a mass of evidence that enables a preliminary correlation to be attempted. It appears that the majority of ore deposits are genetically related to one or another of the igneous

Jan 4, 1917

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992

By Frank Sames

Ground vibration levels are generally predicted using equations such as the USBM equation implementing the scaled distance concept and describing geological and blast design parameters in a ground transmission constant.

Jan 1, 1995

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr2O3. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 16 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, stope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider stopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By Fred V. Carrillo

Of the total quantity of secondary copper and zinc that became obsolete in the United States from 19b1 through 1970, more than 11 million tons of copper and 10 million tons of zinc were not recovered. These estimates are based on a study of the flow and recovery of old copper and zinc scrap by consumption end-use. This report describes (1) where copper and zinc are being used; (2) when they become obsolete and available as secondary metal; (3) how they are being collected for recycling; and (4) how much might be recovered from scrap that presently is not being recycled.

Jan 1, 1974

By D. F. Hambley

This report documents the work carried out by Engineers International, Inc. and its subcontructor, W. G. Pariseau, in order to develop a design manual for ore passes for open pit mines. The work included an extensive information search, novel analyses in rock flow theory, cost and time estimation for shaft and raise construction methods, and development of design criteria for the are pass proper, dump point, and draw point.

Jan 1, 1983

Jan 1, 1969