Search Documents

By L. Westerstrom

Supply and Demand After a dismal first half, the industry saw a marked improvement in its markets during the final six months of 1983. Domestic consumption was 17.6% higher in the second half of the year, primarily due to a surge in electric power requirements. The sharp increase in demand for electric power during the third and fourth quarters afforded utilities the opportunity to lower stocks that had accumulated to record levels during 1982. Consumer stocks were reduced from 179 Mt (197 million st) at the end of June to 153 Mt (169 million st) by the end of the year. That is the largest inventory drawdown on record during a six-month period without a major coal strike. Despite the huge depletion in inventories, coal production in the second half of 1983 rose 1.3% above output in the second half of 1982. However, because of the disappointing first half, production in 1983 totaled only 712 Mt (785 million st), 6.4% less than the 760 Mt (838 million st) produced in 1982. Demand The extent to which the economic recovery affected coal markets in 1983 varied: • total domestic coal consumption increased 4.2%; • electric utility coal consumption increased 5.3%; • exports declined by about one-fourth; • coal consumption at coke plants declined 9.5%; and • coal consumption in the other industrial sectors increased 2.9%. Domestic coal consumption totaled 667 Mt (737 million st) it 1983, 27 Mt (30 million st) more than 1982. Electric utility consumption increased from 539 M1 (594 million st) in 1982 to 567 M1 (625 million st) in 1983. Coal consumption at coke plants declined from 37 Mt (41 million st) to 34 M1 (37 million st). Residential and commercial use increased 181 kt (200,000 st) - from 7.4 to 7.6 Mt (8.2 to 8.4 million st). Electric Utilities: Electric power generation increased 3.1% in 1983. Demand for electric power increased in all major consumer categories. Residential and commercial use rose 2.7% and 3.3%, respectively. The most striking increase, however, and indicative of the economy's strong upturn, was the increase in industrial electric power use. Industrial power requirements, which declined 9.8% in 1982, rose 4.1% in 1983. The electric utility sector continued to expand its use of coal last year while lowering its requirements of oil and natural gas. In 1983, electric generation from coal increased 5.7%, while genera-

Jan 5, 1984

By P. C. Carrasco

Knowing the origin of the relevant and irrelevant components of the nugget effect is essential to optimize the process under study. This paper describes the causes of the nugget effect and, its dependency on the sample support, sampling density, and on the QA/QC procedures. Several examples of natural and ?human? nugget effect are given. A method to estimate the magnitude of the relevant and irrelevant components is suggested. Finally, the economic consequences of misunderstanding the nugget effect are analysed.

Jan 1, 2010

By Dave Minney

The South African mines health and safety regulations require that mine management establish a quality management system for rock support material. Quality control of resin capsules used as a support medium in South Africa is specified under SA National Standards No 1534. Experience has shown that this specification, while addressing the chemical and physical aspects of the products, but does not address the required performance criteria. In order to address this shortcoming, the industry has put a lot of emphasis on short encapsulation pull tests, performed insitu, in the underground workings of the mine. This is also fraught with many shortcomings, particularly as regards site availability, cost and repeatability of results. To try and address these issues, the Department of Mechanical and Aeronautical Engineering at Pretoria University were approached to develop equipment and machinery that could produce reliable, repeatable results in a laboratory environment which reasonably simulates installation practice underground. The test method is based on the ASTM F432-95 Strength Index test, but modified to use push test rather than pull tests. The paper describes development of the test method and the preliminary results and findings of the work.

Jan 1, 2007

By William M. Knuth

This study involved a review of bonding and bond release practices in the states of the Eastern and Midwestern Coal Provinces. Data was collected from regulatory authorities and site visits to document the bonding and release procedures in the states related to achieving successful reclamation. The regulations related to PL95-87 were reviewed. The analysis included suggested modified or new bond release criteria, a review of applicable bond release inspection techniques was prepared, a conceptual graduated bonding system and incentive procedures for reclamation of surface mine sites to alternative or higher land uses. A number of conclusions and recommendations for further research were included. A detailed bibliography and a glossary are included in the report.

Jan 1, 1978

By F. Dehghani

The influence of different grinding methods on the shape characteristics of magnetite particles was investigated. Also, the effect of particle shape on the flotation of the magnetite, both alone and in the presence of quartz particles, was investigated. The shape characteristics of the magnetite particles were measured and calculated from images obtained by scanning electron microscopy via an image analysis system. The flotation tests were performed using a laboratory flotation cell. Results showed that in the -250+212 µm and -106+75 µm size fractions, ball mill products have a higher elongation value than rod mill products, while in the -150+125 µm size fraction, rod mill products have a higher elongation value. Particles with higher elongation values and lower roundness values have a higher flotation kinetic constant. Furthermore, the influence of magnetite particle shape on flotation is greater, and the flotation kinetic constant is higher, in the presence of quartz particles than in the flotation of magnetite alone Keywords shape, elongation value, flotation kinetics, magnetite.

Dec 1, 2013

By The Staff

THE object of the work was to increase the capacity of the plant and, if possible, to reduce costs of the actual unit grinding while doing so. The accompanying assays of an infra-sizer analysis of the cyanide tail (Table l) illustrate the problem in hand. The cyanide tail is a combination of two products, gangue and FeS2. The assay alters by virtue of a change in gold value due to grinding and the relative quantity of FeS2 in the sizes, which itself varies with the grind. The disposal tail is the residue after the cyanide tail is scavenged by flotation, most of the pyrite being removed for roasting. It presents a somewhat different problem, since grinding gangue is all gain, but -10 micron FeS2 does not float nearly as well as + 10 product. This results in compromise in the final size to be aimed at. Extra grinding has hardly any appreciable effect on the gold extraction from the FeS2. (See Milling Investigations Into the Ore as Occurring at the Lake Shore Mine; Trans. C.l.M.M., Vol. XXXIX, 1936).

Jan 1, 1940

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

By H. Kenworthy

Small batches of fluorspar flotation concentrates were made into nodules and pellets on a laboratory scale. Several of these were rated acceptable by laboratory evaluation methods. The most satisfactory pellets were produced by mixing fluorspar with about 12.5 percent of water, by weight, and 4 percent of organic binders. These binders) for the most part) originated from petroleum and wood-pulp industries. They were generally difficult to handle and were not easily incorporated with the fluorspars tested. Most of them seemed to have an aversion for damp fluorspar and had to be forcibly mixed with the fluorspar; which was then formed into pellets by pressure. Substitution of fuel oil in varying amounts in the binders enhanced the mixing and penetrating qualities of these binders but at the same tire tended to make the pellets more porous. Tall oils performed the same function to a lesser degree and usually decreased the water absorbency of the finished pellets. Heat-treating temperatures to set up these binders were moderate -about 5000 F. for 30 to 50 minutes was usually enough for both drying and heat treating. Nodules made with 1-1/2 to 2 percent of bentonite as a binder were easily mixed and formed. They required a high degree of heat (about 1,500° F.) to develop their strength and were quite water-absorbent when finished. Two fluorspars were examined for weight and fluorite loss after heat treatment at similar temperatures. Both showed a definite wej.ght and analytical loss of fluorite. Bentonite was used also as a binder to successfully nodulize finely ground oxides of iron, manganese, and nickel.

Jan 1, 1951

By F. Terblanche, M. Holton, A. Kruger

The paper presents an optimal mine planning system designed to simultaneously optimize all the underground mines of large South African gold and platinum mining corporations. The system, code named PlanIT-OPTIM, is a multi-stage solution involving the use of adetailed 3D CAD-based mine planning system (CADSmine™V4). The mine design and scheduling rules defined in CADSmine™ are responsible for simulating mining sequencing, rock mechanics, and ventilation, etcetera. Feasible production ranges generated by CADSmine™ and various high-level mathematical models are used as inputs to a mathematical optimization engine. The optimization engine produces optimal production profiles (i.e. key business indicators such as tonnages, mineral and areas extracted per time period) by maximizing net present value. Other objectives such as profit continuity, production continuity and maintaining available reserves can also be specified as optimization criteria. The final step in the PlanIT-OPTIM process is to convert the optimal production profiles into practical and attainable business plans. This is achieved through the CADSmine™ Detail Optimization Engine that modifies the original CADSmine™ schedule to match the optimal production profiles. With current methods it is an impossible task to find the best business plan for a mining corporation in any reasonable period of time should conditions change (e.g. gold prices, exchangerates, grade estimates, etcetera). The fast turn around time achieved through PlanIT-OPTIM makes it possible to do several ‘what-if’ scenarios in a reasonably short time. PlanIT-OPTIM has already been used in the gold mining industry to find optimal business plans for a mine.

Jan 1, 2003

By Steve Kral

Borates are minerals that contain boron. Trace amounts exist in rocks, soil, water and people. Boron-containing ores are rare and U.S. Borax, a subsidiary of Rio Tinto Borax, controls one of the world’s two world-class borate deposits. Through its global systems of mines, refineries, ports, sales offices and distribution centers, the company supplies nearly 45 percent of the world’s demand for borates. Borax has been mining borates in California for more than a century. This year the company celebrated 131 years of continuous business in the Golden State and 76 years at its operations in Boron, the site of California’s largest openpit mine. It also has mines and refineries in Argentina, refineries and ship-ping facilities in Europe and technical staff in the United States, North and South America, Europe and Asia Pacific. So, with the 130±years of borate mining and processing experience behind it as well as its global marketing and distribution centers, there is very little that Borax does not know about borates.

Jan 1, 2003

By J. C. Edwards, C. C. Hwang

In ventilated tunnel fires, smoke and hot combustion products may form a layer near the ceiling and flow in the direction opposite to the ventilation stream. The existence of this reverse stratified flow has an important bearing on fire fighting and evacuation of underground mine roadways, tunnels and building corridors. In the present study, conducted by the National Institute for Occupational Safety and Health, a CFD program (fire dynamics simulator) based on large eddy simulations (LES) is used to model floor-level fires in a ventilated tunnel. Specifically, the critical ventilation velocity that is just sufficient to prevent the formation of a reverse stratified layer is simulated for two tunnels of different size. The computer code is verified by checking the computed velocity profile against experimental measurements. The CFD results show the leveling-off of the critical ventilation velocity as the heat release rate surpasses a certain value. At this critical ventilation, the ceiling temperature above the fire reaches a maximum for both tunnels. The velocity leveling-off can be explained from this observation. An extended correlation of Newman (Combust. Flame 57 (1984) 33) is applied to the temperature profiles obtained by CFD. At the critical ventilation, temperature stratification exists downstream from the fire. The computed critical ventilation velocity shows fair agreement with available experimental data taken from both horizontal and inclined fire tunnels. The CFD simulations indicate that the Froude modeling is an approximation for tunnel fires. The Froude-scaling law does not apply to two geometrically similar fire tunnels. The CFD results are compared with two simple theories of critical ventilation by Kennedy et al. (ASHRAE Trans. Res. 102(2) (1996) 40) and Kunsch

By J. M. Krese

This paper gives an overview of the National REAP program emphasizing the program's current status and future plans. A brief historical review of the program will be given containing roof-fall accident trends and statistics. The latest developments in roof control technology and training as it affects the REAP program will be presented. A brief discussion concerning some effects of the implementation of the amendments to Part 75, CFR, concerning roof support is included.

Jan 1, 1988

By R Wilson, R Williams, B Freeburn

McLanahan RSS14x50 scrubber screens have individually processed over 50 Mt of Pilbara iron ore. The first stage of separation in these plants with abrasive, high specific gravity, large lumps is an extremely arduous duty with high wear rates. With the Scrubber Screen layout this occurs in the attached trommel section. The initial supply of the replaceable trommel panels were of steel-backed rubber with a service life of approx. six weeks. Site Personnel established a goal of 26 week wear life in conjunction with 100 per cent reliability and while field trials were undertaken using a variety of hardened and cast steels that demonstrated wear life to the nominated requirement some unpredicted failures still occurred. With a long evaluation time and challenges to create repeatable conditions with field testing, a purpose built test unit was designed and constructed to allow controlled evaluation of a number of materials and designs. During 2016 tests were conducted with eight different materials, of varying thickness to simulate impact conditions and a number of aperture profiles to evaluate both impact and abrasion effects. From these results two designs were selected for full scale implementation to confirm the nominated goals. This paper will present details of both testing procedures and results of all materials, as well as conclusions of successful field implementation.CITATION:Wilson, R, Freeburn, B and Williams, R, 2017. Trommel panel development for iron ore applications, in Proceedings Iron Ore 2017, pp 251–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Frank E. Williams

This Bureau of Mines report deals with the urbanization of Tucson, Ariz., a southwestern city with an arid environment. Zoning regulations concerning known aggregate sources are described, and information relating to projected needs for the urban area is furnished. History of growth is outlined not only for the local aggregate industry, but also for the entire urban area. Past conditions are pointed out and background material for future conditions is provided.

Jan 1, 1967

By Ronald Molnar

"High demand for metals is driving the exploitation of lower grade and more complex orebodies. These projects are often the initiatives of junior mining companies with limited financial resources. In addition, existing operations seek to enhance revenue from their existing metal recovery operations, through the production of value-added by-product metals and chemicals. Typically, hydrometallurgical circuits, often with novel chemistry, are required to exploit these new ores, to produce the multiplicity of products that will make a marginal project economical, or to increase the product range of an existing operation. Often, the mineral processing engineer is given the task of coordinating the development of a back-end hydrometallurgical flowsheet for their mineral processing project. This paper discusses the objectives that companies have when they commission the operation of a hydrometallurgical pilot plant. The paper goes on to enumerate some of the principal differences between mineral processing and hydrometallurgical pilot plants and the effect these have on the design, operability and potential pilot plant outcomes. Important factors include working with chemically reactive solutions and pulps, elevated temperatures operation, changing rheological properties of slurries, the complexity of integrated circuit flowsheets with long hold-up times and multiple recycle streams, and the need in some cases for extreme attention to purity and cleanliness. Examples will be drawn from the extensive experience base of SGS Minerals Services at the Lakefield site, in piloting both mineral processing and hydrometallurgical process flowsheets.INTRODUCTIONWe are currently experiencing a period of strong growth in the demand for metals. This in turn is turning the spotlight on a great many smaller mining companies and mining promotion ventures trying to tap into the rising metal demand. Some of these companies want to develop their properties and recover metals while others want to develop to the point that a major company will take an interest, or in some cases buy them out completely.With the heightened interest in metals, many orebodies that have been known about for years are being reconsidered for exploitation. Often, the reason they have not been developed to date is because of difficult metallurgy and marginal grades leading to marginal economic viability. In both cases the key that unlocks the resources is often the application of a novel metallurgical flowsheet, often a hydrometallurgical flowsheet."

Jan 1, 2006

By Benjamin Cebrian

Traditional dilution control systems range from computer modeling, use of physical markers on the field as polypipes to a technology that marks some control points where displacement is measured. The latter includes walking over a muckpile which is prohibited by some mining companies as a safety measure. The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

By L. Sahu, S. Bhattacharya, S. Dey

"An ideal procedure to determine the limits of flotation-based separation, as is the case with washability analysis for density separation, does not exist. Therefore, a procedure called release analysis, considered to be the counterpart of the washability process in density separation, was developed to evaluate the flotation characteristics of coal fines. Since flotation is a complex process it is necessary to know the maximum recoverable yield that could be achieved at a target ash level and what could be obtained by release analysis. Due to a number of limitations in the initial procedures, modifications were recommended by various researchers to generate an optimum separation curve. This paper presents a review of, and a discussion on, the chronological evolution of release analysis methodology over the decades. Notwithstanding the availability of a standardized release analysis procedure, such as BS 7530, the paper highlights the critical parameters involved in the procedures, such as coal type, feed characteristics, choice of reagents and dosage, operator bias, and design features of the flotation cell IntroductionCoal is a heterogeneous substance consisting of various combustible constituents (macerals) and associated mineral matter. The kind and abundance of the various macerals present in the coal, such as vitrinite, semivitrinite, exinite, and inertinite, determine the type of coal. As macerals are formed by biological degradation of different parts of the plant material, they have different properties based on their original composition. Coal cleaning processes are dependent on the differences in physical properties between the coal components (the macerals) and also between the macerals and the mineral matter. Thus the cleaning characteristics of the coal might vary from one type to the next. The cleaning processes influence the distribution and the concentration of macerals in the various size and density fractions of the cleaned product."

Jun 1, 2019

On the basis of field observation, four principal styles of hydraulic breccia are recognised, and their characteristic features noted. In practice, hybrid styles are most commonly encountered. Numerous examples will be illustrated during the oral presentation, and the potential for definition of a formative environment is emphasised. In one example presented, it is suggested that more than 50 episodes of hydraulic fracturing can be recognised. In all cases at least sane useful conclusions can be drawn in the context of modeling for drill targets.

Jan 1, 1987

By E. McCullough, D. Preece, M. Ortel

Geophysical explosive charges are used in mineral resource exploration. They are detonated subsurface and radiate sonic waves into ground monitors, which detect the vibration waves and their interaction with underlying geologic strata. Geophysicists perform computer analyses of the waves reflected from the strata to determine their depth and thickness (Strobel, Berger & Schaefer, 2012). The purpose of this research is to determine how the detonating explosive charge interacts with the adjacent ground and how the induced waves propagate through the surrounding medium. Furthermore, it is necessary to optimize the location of the initiation point within the charge. Establishing both the direction and intensity of the waves will allow geoscientists to refine and optimize geophysical studies that employ explosive charges.

Jan 1, 2013

By P. Kolodziejczyk

Mining seismicity can be harmful both under and on the surface. ? Tremors are not totally damaging, but destructive to buildings and infrastructure, especially in highly urbanized regions, such as Upper Silesia in Poland ? Destroy the social appreciation, trust and support for mining industry ? To prevent or reduce these effects, engineers and scientists develop methods allowing prediction of ground shaking intensity near buildings and various losses that can result from it Evaluation and prediction of mining tremor?s damaging influence on buildings is usually solved with two steps: ? Estimation of local ground shaking intensity (based on known attenuation relation) and classification into one of several predefined intensity intervals ? Apply supposed relation between the shaking intensity interval and qualitatively defined damaging effects to express predicted effects This makes a mixed quantitative/qualitative procedure, difficult to analyze or optimize

Aug 1, 2013