Search Documents

Fire suppression systems are now recognised by both NFPA 502 and PIARC as legitimate tools for both life protection and asset protection. The effectiveness of these tools for life protection demands extremely rapid and accurate incident detection coupled with rapid response. This rapid response must be integrated with other emergency systems such as emergency ventilation. The March 2007 fatal Burnley Tunnel incident in Australia graphically illustrates the potential of effectively integrated fixed suppression systems to protect people from harm and save infrastructure from damage. Despite the raft of technology available in that instance to the operator it was the human operatorÆs ability to effectively control the emergency equipment and not the equipment itself which so positively influenced the threat to life and property.

Jan 1, 2008

By Matteo Montesi

Deep foundation elements are often used as discrete elements in externally supported earth retaining structures such as soldier piles and lagging walls, secant/tangent pile walls, anchored walls, etc. These structures can be designed using different approaches such as conventional limit equilibrium methods, finite element/difference analyses, and soil spring (p-y) analyses which are contained in various commercially available computer programs used by engineers worldwide. Although these programs usually undergo various degree of verification and validation, users must be aware of each program’s limitations and conditions in which each design approach should or should not be used. These programs may incur difficulties when non-continuous deep foundation elements are used as part of the retaining system and in cases of non-uniform geometry where closed-form solutions are not available. Design input parameters such as passive arching width, wall-to-soil friction, and p-multipliers (pm) are not always given enough attention which may result in potential design deficiencies. This paper presents the main features of various earth retaining structure design approaches and discusses their advantages/disadvantages. The paper addresses some of the limitations and difficulties that may be faced with when utilizing non-continuous discrete deep foundation elements and identifies key elements that are sources of potential deficiencies and errors. An example comparing the design outcomes using different design approaches is presented. INTRODUCTION Earth retaining structures are used to retain soil and create or maintain a difference in ground elevation between grades in front and behind the retaining structure. Deep foundation elements have been used for decades to support earth retaining structures. Earth retaining structures that are supported by deep foundation elements are typically referred to as externally stabilized system (O’Rourke and Jones, 1990). An externally stabilized system uses an external structural element, in contrast to internally stabilized systems which rely on reinforcements installed within and extending beyond the potential failure mass. The design of externally supported retaining structures can be accomplished using different approaches, which can be challenging under certain conditions. Each approach has been discussed extensively in available literature, and is well summarized in the and Federal Highway Administration (FHWA) guidelines. The objective of this paper is to present the most widely used design approaches and discuss their limitations and difficulties in one concise and brief document, giving the reader a good source for comprehensive understanding of the various design approaches, supported by a technical example. This paper is not intended to be a comprehensive review of all available design methods and formulations available in the literature.

Jan 1, 2018

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage-, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation With the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects. The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry Missouri School of Mines and Metallurgy, and. Will H. Coghill., supervising engineer of the ore dressing section of the United States Bureau of Mines.

Jan 1, 1932

By John E. Tilton

The ability of companies and countries to mine copper and other mineral commodities competitively and in the process to generate new wealth depends on their mineral endowment. Chile, for example, produces and exports copper because it is well endowed with high-quality, low-cost deposits. This production creates wealth that benefits mining companies and their stockholders, the government, local communities, as well as copper consumers around the world. The widespread perception that mineral endowment must largely determine competitiveness, or what economists call comparative advantage, must be true at any particularly moment. Countries with abundant reserves must be competitive. This follows from the definition of reserves — the quantity of a mineral commodity found in discovered deposits that are profitable to exploit under current conditions. As a result, it is a tautology and not particularly interesting. The important question is what causes reserves to change over time, producing in the process new wealth and shifts in competitiveness?

Jan 1, 2003

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989

By Henry Stoch

It?s a green, green world ? Public concern about the impact of human activities on the environment and the roles that businesses play in that impact is rising. What?s happened in the last few months? ? Recent news: ? British Columbia announces carbon tax in 2008 budget ? Federal Court ruling stalls oil sands approvals due to a lack of consideration of GHG implications ? US Energy Independence and Security Act could limit government procurement of oil sands-derived fuels ? Western Climate Initiative (WCI) suggests a ?first seller? approach for regulating generators outside WCI jurisdictions ? Implications ? A cost for carbon has arrived ? The lack of a GHG strategy can have a material impact on your business ? Regulations in other jurisdictions could affect your organization

May 1, 2008

By J. -H. Wu, S. Nishiyama, Y. Ohnishi

The behaviors and stress distributions of the inclined jointed rock masses with different dip angles obtained from DDA are compared to the results of laboratory tests. By calculating the block stress distributions, it is confirmed that DDA can reproduce the arching around the trap door when lowering the trap door. The shapes of arching change with the angles of inclined layers. In addition, the earth pressures acting on the trap door shows non-symmetrical distributions when the layers are not horizontal. The stress concentration occurs in one side of the rock masses close to the trap door. Furthermore, the surface settlements are also related to the inclined angle, and the loosening zone in rock masses can be different from Terzghi’s theory [1]. Since, simulations have good agreements with the laboratory test , it demonstrates the applicability of DDA to explain the mechanical behaviors of tunnel, such as arching phenomenon, non-symmetrical earth pressure distributions acting on the trap door, and the surface settlement profile in the jointed rock masses. Dans cet article est décrite l’étude numérique du perçage d’un tunnel dans un massif de couches rocheuses jointes inclinées. La simulation à l’aide de l’Analyse de Déformation Discontinue (DDA), en faisant varier l’angle d’inclinaison des couches de roche, nous apporte des résultats en termes de distributions de contraintes et de comportement des couches, résultats qui sont ensuite comparés avec des résultats de tests en laboratoire. Les résultats confirment le fait que la DDA est capable de reproduire le phénomène d’arcage autour de la trappe lorsque la trappe s’abaisse. Les formes d’arcage varient selon l’angle d’inclinaison des couches de roche. Par ailleurs, lorsque les couches ne sont pas horizontales, la distribution de pression agissant sur la trappe est assymmétrique. La concentration de contraintes se produit du coté proche de la trappe. De plus, les tassements de surface dépendent eux aussi de l’angle d’inclinaison. En conséquence, les résultats de simulation sont en accord avec les tests en laboratoire, ce qui prouve que la DDA permet d’expliquer des comportements mécaniques du tunnel tels que l’arcage, les distributions assymmétiques de pression du sol sur la trappe, ainsi que le profil du tassement de surface dans la masse de roches jointes. Dieser Beitrag beschreibt eine numerische Studie über Tunnel im geklüftetem Fels. Das Verhalten und die Druckverteilungen in den unterschiedlich geneigten und geklüfteten Felsenmassen wird mit Hilfe des Discontinuous Deformation Analysis Programms (DDA) simuliert, und mit Laborversuchen verglichen. Die Resultate bestätigen, dass DDA der Gewölbewirkung im „Trapdoor“ Experiment gut reproduzieren kann. Die Form des Gewölbes, ändert sich mit unterschiedlichen Neigungswinkeln der Schichten. Bei geneigten Schichten entstehen unsymmetrische Druckverteilungen. Auch die Oberflächenabsenkung ist von dem Neigungswinkel abhängig. Die gute Übereinstimmung der Simulationen mit den Laborversuchen zeigt, dass die DDA-Methode gut geeignet ist, um das mechanische Verhalten von Tunneln, wie z.B. den Effekt der Gewölbewirkung, die unsymmetrischen Druckverteilungen bei geneigten Schichten, oder die Oberflächenabsenkung in geklüfteten Felsenmassen, zu erklären.

Jan 1, 2003

By J. R. Thoenen

[Before 1914 Germany held a virtual monopoly on the world supply of potash for fertilizer purposes. During the World War, potash shipments to the United States ceased, and recourse was had to domestic supplies. High war-tine prisms stimulated interest in various sources, and domestic production increased rapidly. At the close of the war, resumption of shipments from Germany mad other sources reduced prices to below pre-war levels, and, as a result, most of the domestic procedures ceased operations. This experience demonstrated that a domestic source of potash was necessary but that it must be of such a nature that it could compete in price with foreign sources. As a direct result the potash content of thick]

Jan 1, 1941

By R. Dekkers, J. Plessers

The feasibility of using hydrogen to obtain clean steels is investigated. High hydrogen contents are generally considered as detrimental due to the risk of flakes, bubbles and breakouts during casting. Hydrogen can nonetheless be removed by degassing of the steel. The results of industrial campaigns, where total oxygen content and hydrogen content were monitored, are presented. High resolution microscopy of inclusions and laboratory experiments on the rate of inclusion removal by CaO-Al2O3 slags at different partial hydrogen have been carried out. So far, evidence that hydrogen may influence inclusions or the steel cleanliness is not clear. Keywords: hydrogen, cleanliness, inclusions.

Jan 1, 2004

By Chester M. F. Peters

INTRODUCTION There has been considerable discussion in recent years of the strained relations between owners, engineers and contractors caused by the rapid increase in costly litigation in underground excavation due to construction claims. These time consuming claims are not to the best interests of the industry. It has been a conclusion of some of the concerned parties that there could be a substantial reduction in these claims if a mutual respect for each other's roles could be maintained along with a practical contractual arrangement for sharing the risks of the unforeseen costs inherent in the business. This paper will touch on the overall problem of these relationships, but confine the major discussion to the role of geology in claims and, in particular, changed conditions claims, since they form the base for the bulk of those involving geology. Geologists can make a major contribution to the reduction of these claims if their particular abilities are recognized and used properly. CLAIMS AND GEOLOGICAL RISKS The tunnel contractor is strictly bound by the contract he signs, and the risks he assumes thereby must be priced. The most important variable factor on which he must base his price is the geologic data provided and his interpretation of it. If this data does not give a clear picture of the conditions, making it impossible to price

Jan 1, 1974

The great problem at Port Pirie and many other lead smelters has always been to keep the lead content of the slags down to a low level. This has been done in the past largely by empirical methods, the lead content varying from less than 1 per cent to over 4 per cent, the more usual figure being something under 2 per cent. Subsidiary to this, but of major importance in the future, was the extraction of the considerable quantities of zinc in the slag. At this stage little was known about the constitution of the slags apartfrom their chemical composition. Some early work on slag constitution was carried out in the B.H.A.S. Research Laboratories between 1919 and 1921, but except for a microscopic examination of a few thin sections the greater part of this investigation wasdevoted to the recovery of the zinc content of the slag by leaching methods.In 1949, therefore, it was decided to initiate a programme of fundamental research into the constitution and properties of the lead blast furnace slags. The information thus gained would give a clearer picture of reactions taking place in the slag, both in the blast furnace and during dezincing.There was also the hope that these results would lead to improved industrial techniques resulting in smaller lead losses, and, taking the long-term view, to efficient methods of producing zinc from the slags.A series of investigations was therefore begun at various centres over a period of time. These were:1. A mineralogical examination of the slags by Dr. A. B. Edwards of the Mineragraphic Section, C.S.I.R.O.2. A study of the thermodynamics of various slag com...

Jan 1, 1956

By S. R. Sankaranarayanan, T. Sowmya

Slags and fluxes used in metallurgical processes are typically made up of oxides (especially silicates), with additions of fluoride and carbonaceous matter. Despite the efforts made towards understanding the role of slags in various processes, little information is available on the structure of these slags. Tools such as X-ray diffraction, spectroscopy, and electron microscopy could be used for this purpose. This paper is based on an ongoing spectroscopic and structural investigation of slags and related materials. Spectroscopic studies of various commercial slags (predominantly ferrous), ores, glass and related materials, covering a wide range of compositions, have been carried out to understand the structure. The infrared spectra were recorded, predominantly, using FTIR spectrometer (Bruker IFS 66U) spanning 4000 to 100 cm-1using the KBr pellet method. The resolution was typically 4 cm-1. The spectral outputs have been compiled in terms of bands present (corresponding to different bonds) and then compared with the typical bands expected for such bonds. Efforts are in progress to identify the trends with respect to the chemical composition?for example, the effects of SiO2, Al2O3, and non-bridging oxygens. Data obtained so far indicate some trends such as (i) a shift in the Si-O band (969 to 1099 cm-1) towards a higher wave number with increasing silica content (almost 2 to 92 weight percentage) and (ii) further strong shifts as a function of the alumina content. These are being further investigated structurally and in terms of chemical composition/parameters. Keywords: slags, silicates, structure, spectroscopic analysis, shifting of bands

Jan 1, 2004

By Maurice Deul

For the first half of the 21st century, the United States will rely on the same mix of fuels it has for the past 50 years. Petroleum for the United States will cost more and availability will decline as developing nations modernize. Increased use of natural gas for electric power generation will result in stress on the gas supply. Coal will be the fuel of last resort. More than half the petroleum used is imported, about the same amount as used for transportation. Only coal can provide relief by fueling railroads through electrification while encouraging “piggy-back” trailer haulage, co-generation for manufacturing and expanded passenger service.

Jan 1, 2002

By M. Soleymani Shishvan

"Continuous mining systems containing multiple excavators producing multiple products of raw materials are highly complex, exhibiting strong interdependency between constituents. Furthermore, random variables govern the system, which causes uncertainty in the supply of raw materials: uncertainty in knowledge about the reserve, the quantity demanded by the customers, and the breakdown of equipment. This paper presents a stochastic-based mine process simulator capturing different sources of uncertainties. It aims to quantify the effect of geological uncertainty and its impacts on the ability to deliver contractually defined quantities and qualities of coal, and on the system efficiency in terms of utilization of major equipment. Two different areas of research are combined: geostatistical simulation for capturing geological uncertainty, and stochastic process simulation to predict the performance and reliability of a large continuous mining system.The process of modelling and simulation in this specific production environment is discussed in detail. Problem specification and a new integrated simulation approach are presented. A case study in a large coal mine is used to demonstrate the impacts and evaluate the results in terms of reaching optimal production control decisions to increase average equipment utilization and control coal quality and quantity. The new approach is expected to lead to more robust decisions, improved efficiencies, and better coal quality management.IntroductionContinuous coal mining systems containing multiple excavators producing multiple products of raw materials are highly complex and exhibit strong interdependencies between constituents. A network of conveyor belts is used for transportation of the extracted materials to different waste dumps or the coal stockpile.Optimal decision-making in short-term planning and production control are impacted mainly by geological uncertainty associated with incomplete knowledge of the coal deposit represented in the reserve block model. These uncertainties cause deviations from expected process performance. For more robust decision-making, understanding the impacts of these stochastic elements plays a key role."

Jan 1, 2016

A comprehensive axial test program has been undertaken at the WASM Dynamic Test Facility on the performance of 20mm threadbar. The threadbar tests had a double embedment configuration, with variation to the encapsulation lengths, debonded length and surface hardware and fixtures to examine failure mechanisms. Performance was significantly affected by the collar embedment length and type of fixture nut used. Results ranged from thread shearing occurring between the nut and bar at 1kJ of energy dissipated, to control plastic deformation of a central debonded length dissipating 22kJ.

May 1, 2009

By Thomas M. Keevin, Gregory L. Hempen, David J. Schaeffer

In an attempt to reduce the potential for fish mortality during the explosive demolition of Locks and Dam 26, Mississippi River, the U.S. Army Corps of Engineers, St. Louis District explored the use of a bubble curtain to reduce the fish kill radius of underwater explosions. Bubble curtains are walls of bubbles rising from a bottom-resting bubbler manifold supplied with compressed air. Demolition engineers have long been aware of the attenuating properties of air bubbles in water. As such, air curtains have been routinely used to protect underwater structures from damage by underwater explosive shock waves. However, their use in protecting aquatic resources during full-scale explosive demolition projects was untested.

Jan 1, 1997

By C. Larsen, E. Gratch, B. Flintoff, R. Bradburn

"In 1973 Brenda Mines Limited first investigated the potential use of a process computer to aid in the development of a control system for the concentrator grinding circuit. This initial study and its results are reviewed (1) in a previous paper.Since that time the computer system and its applications have been expanded. After the initial success of grinding circuit control, a second process computer was purchased to function as a back-up device. The two processors are currently operated in a foreground-background mode which allows extensive use of the computing facility for engineering and development work as well as operator training.Because of the relative ease of expansion, the computer has been incorporated into a flotation control system as well as an electrical peak power savings program.It is the purpose of this paper to review the successful application:; of the process computer and to indicate applications which are envisaged for the future."

Jan 1, 1978

By F F. Pitard, K J. Ehrig

The Olympic Dam iron-oxide copper-gold (IOCG) uranium-silver deposit is second in size only to Norilsk, the gigantic metalliferous deposit. Olympic Dam is the largest publicly declared uranium, fifth largest copper and third largest gold resource. The deposit is typified by texturally destructive brecciation and intense iron metasomatism of the Roxby Downs Granite, bedded clastic facies rocks and mafic-ultramafic dykes. The deposit contains over 100 minerals. Copper mineralisation consists of chalcopyrite, bornite and chalcocite. Uraninite, coffinite and brannerite are the dominant uranium-bearing minerals. Gold mineralisation consists of electrum, tellurides and Au-Cu alloys. Hessite is the major silver-bearing mineral. The economic minerals are disseminated throughout the breccia matrix where the average grain sizes of the Cu-sulfide, uranium, gold and silver minerals are ~50, 20, <5, <5 microns, respectively.A significant number of sampling theory-based test programs have been completed since the mid-1990s to establish sampling nomographs, select appropriate sampling (ie split versus chip and interval lengths) and sample preparation protocols, quantify the errors associated with each subsampling stage, determine the practical uncertainty limits of Olympic Dam matrix-matched standards, and identify improvement opportunities related to the ongoing assaying quality assurance / quality control (QA/QC) program. Invaluable knowledge and unexpected insights gained from sampling studies at Olympic Dam have helped to improve our understanding of the distribution of economic and deleterious elements within the Olympic Dam deposit.CITATION:Ehrig, K J and Pitard, F F, 2017. Underground bulk sampling, uniform conditioning and conditional simulation – unrealistic expectations?, in Proceedings Eighth World Conference on Sampling and Blending , pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Met M. E

In choosing the subject for my address to you this evening I was actuated by the knowledge that in the past Australian metallurgical problems have been solved by the introduction of extremely interesting processes. Frequently such processes originated in this country, or at least were first adopted here on a large scale.Chronologically there comes to mind the application of chlorination to the Mount Morgan ores from 1888 onwards.Then the application of pyritic smelting to the Mount Lyell ore body in 1896, followed closely by the successful flotation of zinc blendÇ! at Broken Hill, about 1900, and the treatment of the refractory Kalgoorlie gold ores by roasting and cyaniding. With the development of the differential flotation process at Broken Hill came the production of a slime lead concentrate carrying zinc which necessitated the use of a high zinc slag in the lead smelting process. Although previously considered impossible, the necessarytechnique was successfully evolved at Port Pirie resulting in the accumulation of large tonnages of zinc-bearing slag as potential sources of that metal. The past twenty years have witnessed:-(a) The establishment of a flourishing iron and steel industry, with its attendant coking and by-product plant at two centres in New South Wales, namely, Newcastle and Port Kembla.(b) The establishment of an electrolytic zinc process at Risdon in Tasmania.*Presidential Address, Melbourne, 20th August, 1936.

Jan 1, 1936

Last evening, in Auckland, I heard the Chairman of Heinz US, Dr Tony O'Reilly (who, in addition to Heinz's ownership of our largest food processor, also has substantial personal investments in this country), advocate New Zealand as a 'regional corporate capital'.   Why would someone like Dr O'Reilly hold that view? No doubt, as one of Ireland's great rugby players of the 50s and 60s, he admires at least one thing that we do very well (confirmed again in Dublin over the past weekend). But that's not sufficient to support such a view.   He cited many reasons for preferring New Zealand over, say, Sydney, Australia, calling this 'the most rational in which to locate [an] international headquarters', including û +         we have no capital gains tax; +         a more 'pro-business environment'; +         a 'first class' legal and banking system; and +         a 'simple political system'.   I can find no better 'text for today's address.

Jan 1, 1997