Search Documents

By Alexander B. Reeb, Richard J. Varuso, George M. Filz, Jehu B. Johnson

"T-walls, which are concrete floodwalls in an inverted “T” shape, are an integral component of the Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS). In order to resist large lateral flood loads, T-walls are typically supported on long batter piles that extend through the weak and compressible clays and peats commonly encountered in southern Louisiana. Since the piles are battered, settlement of the compressible foundation soils can result in loads acting normal to the piles and induce pile bending moments. Therefore, the design of pile-supported T-walls is a complex soil-structure interaction problem that requires detailed and careful numerical analysis to accurately estimate the stresses and bending moments in the piles. For this paper, numerical analyses were performed for three cross sections that each included a two-pile T wall system that was installed within a 15-ft tall new levee embankment. The cross sections were identical except that the elevation of the T-wall base was varied. This paper discusses the analyses, and it compares the influence of settlements and flood loading on the pile stresses and bending moments. In addition, this paper includes general recommendations for the analysis and design of pile-supported T-walls in practice.INTRODUCTION AND BACKGROUNDThe recently completed Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS) includes 350 miles of levees and floodwalls and is designed to defend against a 100-year storm surge event. The floodwalls predominantly consist of I-walls and T-walls. I-walls are comprised of a sheet pile wall curtain capped with a monolithic concrete wall above grade. T-walls are similar to I-walls, but they include a wide concrete base at grade, which forms an inverted “T” shape, and they are generally supported by long batter piles that provide additional lateral and rotational stability for resisting flood loads.During Hurricane Katrina, several I-walls failed, resulting in large breaches and devastating flooding (Duncan et al. 2008, IPET 2009). T-walls on the other hand performed quite well, including T-walls that were overtopped and eroded on the protected side, yet still did not collapse. As part of the HSDRSS, more conservative designs and height restrictions were required for I-walls (USACE 2011), and a number of I-wall sections were replaced with T-walls. However, the design of pile-supported T-walls is complex and requires careful consideration of both flood loading and settlements."

Jan 1, 2017

By H. Gurgenli

Mining companies require accurate short-term mining forecasts to meet budget targets and customer needs. Challenging mining conditions along with employee turnover and lack of standard geologic modeling and mine planning processes can result in time-consuming and inconsistent mine plans. Documentation and automation of the processes involved in mine planning, as well as proper software utilization, are critical in overcoming these challenges. This paper discusses the steps involved in achieving an optimized mine planning system to accomplish productive and cost effective operations. In addition, a case study is included to describe the process of implementing a semi-automated system whereby the geologic model and mine scheduling database are updated monthly to incorporate changes in geology in a relatively complex open-pit coal mine. This case study proves that the ability to update geologic models based on the latest information gathered from production drilling and mining activities can greatly enhance the ability to accurately predict short-term mining production.

Jan 1, 2011

By G. Caron, M. Boisclair

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce the energy consumption, thus contributing to the reduction of Green House Gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. A soft-sensor prototype, based on primary crusher data (i.e. energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index, and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e. use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2007

By Barbara Hendrickson

Outline ? Canadian Regulatory Update ? Turning the Corner: Background & Status ? Implications of U.S. Waxman-Markey bill for Canada ? Federal-provincial considerations ? Current certainties and uncertainties ?Turning the Corner? as Originally Proposed ? April 26, 2007 - the Canadian federal government announced Turning the Corner: An Action Plan to Reduce Greenhouse Gases and Air Pollution (?Turning the Corner?)

May 1, 2009

By Anthony Hammond

Geographic Information Systems (GIS) are powerful analytical and data display tools for mining industry management, capable of linking spatial features with tabular data and integrating communications across departmental boundaries. In this sense, the paper point out the GIS application concentrates in four technical areas of underground mining: ownership and mineral claims; exploration management; production; and mine safety. GIS provides land and exploration managers with the ability to consolidate and archive claim data and to georeference property maps defined in local coordinates into world coordinate systems. GIS’s proximity analysis identifies areas of potential safety concern and points to and maps the shortest routes to emergency exits, facilitating the prompt evacuation of mine personnel.

Aug 25, 2002

Results of laboratory studies on the flotation of marmatite (zinc sulphide) with new reagents, which were developed to avoid the use of copper sulphate, are presented.Episulphides were chosen as the basis for the reagents because of their reported special chemical affinity for zinc and cadmium. Attempts were made to solubilize and introduce functional groups to episulphides with organic and inorganic acids, ammonia, phenol, aniline, diethylamine, and pyridine. As a class of reagents, the episulphide-amine combination was generally found effective in zinc sulphide flotation to a greater or lesser degree. Best results were obtained with ethylene sulphide-aniline combination. Although anilino-ethyl mercaptan is the reported reaction product of aniline and ethylene sulphide, it was concluded that the effective zinc sulphide flotation with ethylene sulphide-aniline combination is not entirely due to the formation of the mercaptan.The economics of the possible usage of ethylene sulphide-aniline reagent are discussed.

Jan 1, 1974

By G Tripp, G Lorusso

The Velvet gold orebody (153 Koz Au) is located near the Kanowna Belle gold deposit in the Boorara Domain of the Kalgoorlie Terrane, a subdivision of the Archaean Eastern Goldfields Superterrane (Swager et al, 1990). Gold mineralisation at Velvet is hosted within an intrusion of intermediate composition that broadly follows a sub vertical hanging wall splay of the Fitzroy Shear Zone.Velvet was discovered in 2003 during an underground exploration drilling program targeting potential strike extensions to the Kanowna Belle deposit. Diamond drill hole KDU1595 returned a downhole intercept of 36 m grading 4.6 ppm Au approximately 500 m west of the deposit and at a vertical depth of 700 m below surface in the immediate hanging wall of the primary Kanowna Belle host structure, the Fitzroy Shear Zone. Subsequent drilling completed following the initial discovery, from both surface and underground collar positions, failed to replicate this result.In 2014, KDU1595 was resurveyed gyroscopically and the mineralised intercept correctly located. Additional drilling was undertaken to follow-up the repositioned discovery hole. Challenges included poor drilling angles through the Fitzroy Shear Zone, excessive deviation during drilling and the unknown geometry of the target. Navigational drilling helped to successfully penetrate the Fitzroy Shear Zone and in April 2015, drill hole KDU3234 returned a significant downhole intercept of 45 m grading 5.6 ppm Au.Additional drilling success resulted in a decision to develop a 600 m drive to serve as a dual-purpose access for further exploration and mining. This was a potential risk considering that the orebody geometry was unknown and all significant drilling results were clustered within a 50 m × 50 m panel. Development commenced in June 2015 and the first ore cut taken in April 2016. Geological mapping and structural interpretation, together with multi-element and spectral analysis of drill samples has enabled several other target areas to be identified for exploration. The Velvet mining area is critical to continued production at Kanowna Belle. Geological understanding must advance as mining progresses to ensure continued resource growth and optimal extraction of reserves.CITATION:Lorusso, G, Rogers, J and Tripp, G, 2017. Velvet underground exhumed – discovery and development of a new mining front at the Kanowna Belle gold mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By James E. Parkes

The Silver Spring Transit Center is a new three-level transit center that will include bus loops for County, Metro and intercity buses, parking, and retail space. It replaces an existing bus station and connects to a busy metro rail station in downtown Silver Spring, Maryland. Significant site constraints in both plan and profile had to be dealt with in developing a design for support of the structure. Over 90 rock-socketed drilled shafts ranging in size from 3 to 7 foot in diameter were ultimately used to accommodate the limited space and large column loads, and to adapt to the variable rock surface at the site. Site access during design was limited due to the existing active bus station, so contract documents were adapted to include further explorations. Differences in anticipated and actual field conditions regarding the depth, quality, and variability of the rock had to be overcome in construction. Osterberg Load Cell testing during construction allowed for verification and optimization of the shaft design. Additional issues dealt with on this constrained site in an urban setting included construction staging issues, such as working around specialty contractors for tieback walls, blasting operations for rock excavation, productions issues for hard bedrock, as well as coordination issues with third parties, most notably the Washington Metro Area Transit Authority. Aspects of the foundation design and optimization, preparation of the contract documents to deal with the complicated nature of the project, and lessons learned from construction are also discussed.

Jan 1, 2011

By J. S. Stachulak

The Diesel Emissions Evaluation Program (DEEP), a research consortium formed in 1997 by Canadian mining companies, labour unions, and provincial and federal government departments, completed its work by mid-2006. This program, in which Vale Inco participated with both direct funding and in-kind contributions, investigated the ability of currently available technology to significantly reduce underground concentrations of diesel particulate matter (DPM) with high efficiency and low maintenance over a long-term period (years of life).While DEEP?s testing showed that engine maintenance is a critical component for lowering DPM, it was clear that reduction of DPM to the very low target levels of ~0.05 mg/m3 was not possible with maintenance alone. The best candidate technology for achieving low DPM levels was particulate filter systems. Furthermore, successful deployment of such systems was highly dependent on removing them from having to rely on human intervention for their regeneration. The search continues within Vale Inco to identify a reliable and rugged system.

Jan 1, 2009

By M. Bwalya, L. Mabokela, L. C. Woollacott

This paper presents a study on the ability of the King stratification modelto describe density stratification patterns that are achieved under idealizedconditions. Tests were conducted in a batch jig using artificial particles inseven density classes. All particles in a density class had essentially thesame density, size, and shape. Tests were conducted for particle systemsinvolving from two to seven components. Good agreement was obtainedbetween measured and modelled data to an extent that gave strongendorsement of the mathematical appropriateness of the core equation inthe King model. Somewhat ambiguous results were found with regard toclaims about the independencies of the single experimentally-determinedparameter required by the model.

Jan 1, 2015

By Jamal Rostami, Ataollah Rahbar

"Uma Oya Multipurpose Development Project is under construction in Sri Lanka. This project involves 2 Rolled Concrete Core (RCC) Dams connected through a tunnel currently under construction by Drill and Blast method. The water is transferred from first diversion dam to the 2nd regulatory dam and from which, it will be transferred through a 14 km headrace tunnel to the top of a 650 m deep drop shaft that feeds the high pressure water to an underground powerhouse and turbine chamber for generation of 120 MW of electricity. The Headrace and Tailrace tunnels are being excavated by two 4.4 m diameter double shield TBMs. The headrace tunnel has already passed 5km milestone and is mined in hard rock, while the tailrace tunnel has been completed in rather weak and fractured ground. This paper will review the history of the project along with the geology of the site. The operation of TBM in headrace tunnel will be discussed in more detail, focusing on the challenges of excavating through very strong and abrasive quartzite and gneiss on this site, as well as reaches of tunnel in high inflow of water reaching 400 L/Sec. INTRODUCTION This paper aims to introduce the Uma Oya Multipurpose Development Project (UOMDP) as a hydro mechanical project in Sri Lanka, targeted generating hydro-electric power, transferring water for irrigation purposes and controlling seasonal devastating flood. This project lies in the south-eastern part of the central highland region of Sri Lanka (Figure 1). The main part of the project is located in the south-western part of the Badulla district in the province of Uva. The south-eastern end of the project site is in the central west of the Moneragala district (province of Uva). Bandarawela is the largest urban setting within the project area, located halfway between the upstream and the downstream ends of the planned hydropower plant and combination of dams, tunnels, and downstream facilities. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya. The feeder (power) tunnel Lot consists of a headrace tunnel (L=15554m), the surge shaft (L=200m) and tank on the upstream of the vertical shaft, a vertical shaft with steel lining (L=650m), an underground powerhouse and a tailrace tunnel (L=3650m)."

Jan 1, 2016

By André R. Laplante

"This presentation reviews three continuous centrifuge separators, the Falcon-C, Kelsey Jig and Multi-Gravity Separator, two units with possible synergies with centrifuges, the In-Line Pressure Jig and InLine Leach Reactor, and two centrifuge prototypes, the continuous Knelson and the Altair Jig. Typical applications, potential problems, promising synergies and general concentration mechanisms are discussed. A general discussion on the sources of information, the nature of the fluidization water flow, test work for potential centrifuge separations and the early life cycle of new technology, using centrifuge separators as an example, follows. ResumeCette présentation fait le point sur trois appareils de séparation centrifuge, le Falcon-C, bac oscillant Kelsey et Multi-Gravity Separator; deux appareils qui présentent des synergies possibles avec les centrifuges, le bac oscillant In-Line Pressure Jig et le système InLine Leach Reactor; et deux prototypes centrifuges, le Knelson continu et le bac oscillant Altair. On y présente des applications typiques, les problèmes d’opération les plus usuels, les synergies les plus intéressantes. On discute également des sources d’information disponibles pour le minérallurgiste, de l’impact du mode d’ addition de l’eau de fluidisation, de la démarche expérimentale a faire avant d’installer un centrifuge, et du cycle de développement de nouveaux équipements, en utilisant les centrifuges comme exemple.IntroductionGravity separation has undergone a renewal in the past 20 years, much of it attributed to centrifuge units. The semi-batch Knelson Concentrator has probably received the most exposure, but it is rather because of the shear number of units sold than the width and breath of its applicability. It excels at recovery very dense minerals in very small concentrations, and has become a workhorse of the gold industry. Falcon’s Super-Bowl comes a distant second, with very similar applications. A number of copycats are available, and are generically identified as “Knelsons.” This presentation will not address these units explicitly, but as possible synergies."

Jan 1, 2000

By Thomas C. Shapiro

This is the second in a series of articles on microcomputers and applications in the minerals industry. The first article (ME, Feb., page 129) discussed microcomputer terms and concepts. This article will discuss software for geology and mining. The third article will cover plant, administrative, and geotechnical software applications. Introduction Geology and exploration are areas where computers have a natural fit. Large volumes of data need to be tabulated, evaluated, and made into maps and reports that allow geologists and management to make a decision on a project or mine. Until recently, the programs that performed these tasks were cumbersome and not user friendly by any stretch of the imagination. Learning time to become an expert in these programs typically would be six months or more. The computers needed to run these programs are expensive mainframes. Several years ago, the use of minicomputers became popular because of their lower cost. Programs were adapted to fit these smaller machines and became friendlier. With the advent of micros, many programs. were rewritten and used the screen capability more effectively, thus providing a real advance in user interface. Programs and Price The definition of micro, mini, and mainframe is becoming blurred. For the purposes of this article, micro refers to either an eight- or 16-bit computer, costing less than $10,000 and, more typically, under $5,000. Mini refers to a 16- or 32-bit computer that typically costs more than $25,000. Mainframe refers to a 32-bit or larger computer that costs more than $250,000. There is a large gray area between micros and minis, and minis and mainframes. Technology and prices are changing so fast that the traditional definitions have become almost meaningless and price has become a better guide. With the arrival of the minicomputer, costs for hardware began to fall, but the programs have tended to remain unfriendly. In some cases, the minicomputer acted as a front end to the mainframe. Cost of both the programs and minicomputers could easily run a minimum of $70,000. A total cost of $200,000 would not have been out of line. The average geologist and company would have a great deal of difficulty justifying such a purchase. The advent of the microcomputer has changed all that. For $3,500 to $5,000, one can buy a 16-bit micro and a printer. Plotters with six pens are available for $2,000 that will produce a 280- x 430-mm (11- x17-in.) map. For several hundred dollars, software is available to act as a word processor, an economic spread sheet, or to perform ground water calculations. In fact, some programs are available for free. Some of these programs are relatively easy to learn. In addition, programs are being developed daily that are easy to use. More importantly, large programs that once ran only on mainframes are being converted

Jan 3, 1984

By W. C. A. van Niekerk, M. H. Fourie

The carcinogenic potential of chromium (VI) has been the subject of numerous environmental and occupational studies, from which many regulatory efforts emanated. Besides the regulation of levels of known toxic substances (e.g. Cr (VI)), the classification of dusts for regulatory purposes has thus far depended on broad definitions of particle size, mainly used to distinguish only between inhalable and respirable particles. In the past, ultrafine particles (less than 0.1 µm diameter) (PM0.1) were often regarded as a non-issue, because it was believed that significant doses would not deposit in the lungs. A growing body of scientific data is indicating that ultrafine particles are more toxic than their coarse counterparts. Increased toxicity can be related to the unique dosimetric aspects of the deposition and disposition of inhaled ultrafine particles. Secondly, ultrafine particles have a larger surface area per given mass. The increased surface area can act as a carrier for co-pollutants, specifically transition metals (including chromium) that could form a coat on the particle surfaces during particle formation. This suggests that the presence of ?inert? ultrafine particles in the environment may enhance the potential for exposure to reactive airborne compounds, including Cr (VI). These factors are particularly important when information on occupational epidemiology is interpreted. It is desirable to consider the particle size distribution, for example when occupational exposure to hexavalent chromium compounds is assessed. Since ultrafine particles are more toxic than coarse particles with the same chemical composition, it could be speculated that cancer slope factors might be related to particle size distribution. This is relevant not only to carcinogenic chromium compounds, but also basically for any particle-associated toxicants. In general, the probability of developing health effects associated with occupational toxicants is likely to be higher when these are associated with the ultrafine particle range.

Jan 1, 2004

By Ike Isagon

Outline 1.Background Sudbury Backfill Operations 2.Alternative Binder 3.Alternative Binder Trial Process Flow Diagram ?Laboratory Results ?Plant Trial ?Final Evaluation and Approval ?Management of Change (MOC) 4.Economics 5.Conclusion 6.References and Acknowledgements

Nov 1, 2011

By H. D. Kline

This publication describes mining and milling methods and costs at the Madison mine of National Lead Co., St. Louis Smelting & Refining Division, in the Fredericktown district of southeast Missouri and is one of a series prepared by the Federal Bureau of Mines on methods, practices, and costs of mining and milling throughout the United States. The are bodies of the Madison mine are known for the complexity and diversity of their are minerals. Sulfides of copper, nickel, and cobalt occur in commercial quantities with lead sulfide, which is the most valuable metallic mineral in are bodies of the Bonne Terre formation in southeast Missouri. Several attempts were made by various operators to mine the complex ores and separate the sulfide minerals before 1927 when National Lead Co. became interested in the Fredericktown district. Operating then as the St. Louis Smelting & Refining Co., the company began mining and milling ores from the Madison mine in 1944 and has operated continuously since then. A recently built refinery produces copper, nickel, and cobalt metal from a concentrate containing iron sulphides and small quantities of copper, nickel, and cobalt sulphides.

Jan 1, 1961

By Antoni Kalukiewicz

From 1997 through 2000, a team of Polish experts headed by the author studied the prospects of mining newly discovered emerald deposits in Afghanistan. This article describes the scheme for mechanization of the mining operations, along with improvements made to the ventilation facilities and lighting. The required equipment was flown to Afghanistan and the Afghan miners were trained in machine operation and maintenance.

Jan 1, 2005

Three stages are involved in the complete design and evaluation of an open cut mine. These are:1. design of the optimu,m ultimate pit, and selectionof the optimum mill capacity,2. development of production schedules, with intermediate pit designs, and3. evaluation of the project, based on factors from stages 1 and 2, by means of discounted cash flow analysis.Stage 1 requires relatively complete information on metal distribution, metallurgical performance, and cost factors, which is used to design a series of pits, corresponding to a range of milling rates.For each milling rate considered there is a unique pit design which maximizes operating profitability. The computer outlines this design (in terms of size, shape, and location; tons and grade of ore; and tons of waste), by considering the effect on profitability of mining each block in the mineralized inventory in relation to every other block which would be affected by its removal.The computer selects only those blocks for mining which result in an overall increase in profitability, maintaining pre-determined wall slope conditions throughout.Both operating profitabilities and capital costs increase with throughput, and the two curves will combine to produce a flat peak in net profitabilities at a certain rate, with its associated pit design.Stage 2 can maximize head grades early in the life of the operation. This increases the projected present value, but there are good arguments for maintaining steady head grades throughout the life of the mine.A modification of the programme used in Stage 1 is used here.Stage 3 is a conventional discounted cash flow analysis, using factors obtained in stages 1 and 2. It can be computerised, but a manual treatment is probably just as fast overall.

Jan 1, 1970

By S. Kitamura

In recent years, the amount of ferritic stainless steel production has increased. However, the rust formation by the salt spray test was pointed out in the past. At the centre of the circular rust zone, pitting corrosion where water-soluble nonmetallic inclusions were embedded was observed. These inclusions originated from the suspended refining slag and consisted of multi-phase oxides and sulphides. By the experiments and thermodynamic consideration of the water-solubility, not only CaO or CaS, but also lime rich calcium-aluminates or calcium-silicates have shown large water-solubility. The composition of oxide phase in the inclusions was almost the same among the samples from molten steel, slab, or cold rolled sheet. On the contrary, CaS was clearly observed around the oxide in the sample of cold rolled sheet, although it was not found in the molten steel or slab samples. The enrichment of sulphur occurred from the desulphurization reaction of the suspended slag particles in the molten steel and also occurred from the diffusion of sulphur to the oxide inclusions during the heating of the slab. The optimization of refining slag composition has lead to produce the ferritic stainless steel without rust formation. Keywords: stainless steel, rust, calcium aluminates, calcium sulphides, water-solubility, refining slag, composition control of inclusions.

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007