Search Documents

Silica reacts with cryolite at 1010°C in two stages. The first stage is the formation of a sodium aluminosilicate of composition consistent with the mineral jadeite (Na20.AI20s.4Si02). The formation proceeds by atleast two different reactions. Formation of alumina or an aluminosilicate proceeds to its limiting value in the first 30 min while the formation of jadeite proceeds at a steady rate until quantitative conversion is achieved after 150 min. The net overall reaction can be expressed by the equation 6 Si02+2 Na3AlF6? (Na20.AI20s.4Si02) +2 SiF4 +4NaF.The second stage involves a slow reaction that proceeds with the evolution of a little SiF4, The net result is the formation of sodium aluminosilicates that are soluble in 30 per cent AlCIs-HCI solutions. While this could be explained by disproportionation of jadeite to form albite (Na20.Al203.6Si02) and nepheline (Na20. AI203.2Si02), it is more likely that it is due to further but limited reaction between the oxides and fiuoroaluminates.

Jan 1, 1972

By Y Zhuang, S La Brooy

The selection of the optimum process route for a new project has traditionally consisted of investigating existing options and ranking them in terms of cost, technical risk and environmental acceptability. With the current focus on sustainable development other factors now need to be considered. Life Cycle Assessment (LCA) of the process options can be used to extend the assessment in terms of their potential for earning renewable energy credits and in judging their ability to achieve greenhouse gas emission reductions. A rigorous life cycle assessment is demanding in terms of setting the baseline for comparisons and evaluating the elements that make up the emission profiles of the process options. However, a simplified LCA can provide a useful tool for comparing different process options. This approach can be combined with traditional assessment criteria to rank the options available to the project. GRD Minproc has been intimately involved in executing LCA calculations for different municipal waste treatment options. This paper applies a similar LCA methodology to investigate the greenhouse gas implications for different options for copper processing. The process options considered are:concentrator û sale of concentrate to smelter, concentrator û on-site mini smelter, and concentrator û leach SX/EW. The paper then goes on to consider the operating cost implications that could arise with the introduction of carbon taxes or carbon credits and how these might impact on the future choice of flowsheet.

Jan 1, 2002

By Jean Rosaire

?GWIOP Location ?Climate and Physiography ?History ?Geology ?Deposit Types ?Mineralization ?Historical Mineral Resources ?Conclusions and Work Program

May 1, 2007

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on total nitrogen oxides (NOX) concentrations were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes.

Jan 1, 2011

Magnetic anomalies in the Southern Coalfields have been subdivided into two characteristic types. Each type is attributed to a separate cause, one being basement structure, and the other near-surface igneous intrusions.Detailed geological mapping of the area and the ability to sample throughout the coalmines greatly assisted in this subdivision.The Triassic sequence contributes no magnetic effect of its own except to diminish the effect of sources within the underlying formations by raising the level of observation.Detecting the presence of igneous intrusions ahead of colliery working faces by magnetic observations within the coal mines may be of value in preventing accidents caused by gas outbursts and in planning the workings so as to avoid loss of production time.

Jan 1, 1967

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961

By Holla L, Tyminski A

Stowing has been successfully used in many countries as a means of controlling surface subsidence, minimi ing incidences of spontaneous combustion, maintaining gate road stability and maximising coal recovery.Australian experience in stowing is limited but in the future increased extraction of thicker and/or multiple seams by longwall operations and resolution of conflict of alternative land u&apos;ses may necessitate the use of stowing in coal mining. At present there is little incentive for mining companies to introduce and operate a stowing system because costs have to be borne by the individual companies and benefits spill over to society and the State. Cost sharing by the industry and State incentives may overcome the problem of cost disincentive.

Jan 1, 1987

By M. R. Pickus, I. W. Pickus

ORDINARILY age-hardening is thought of as being associated with a limited solubility of one metal in another. Much less has been written about the type of age-hardening that attends the formation of superstructures. Solid solutions generally have a disordered or random arrangement of atoms; that is to say, in a unit cell, such as that of the face-centered cubic lattice, there is no distinction between atomic sites. Atoms of a given metal may occupy cube corners or face centers. Under certain conditions, however, some alloys develop what is known as an ordered structure. In this case, cube corners would be occupied by only one type of atom and face centers by another type, Associated with this ordering process are many interesting changes in physical and electrical properties. Moreover, in many instances the alloys become susceptible to age-hardening. From the evidence now to be described, it appears that age-hardening in 14-carat gold alloys is due to the formation of both a super-structure and a precipitate. Alloys of the metals gold, silver and copper were known in antiquity. The available knowledge regarding their constitution has been ably summarized and extended by Sterner-Rainer,1 Janecke,2 Carter,3 Wise,4 and Coleman.5 Despite the long familiarity with these alloys and the numerous investigations of their properties that have been made, there is still much that remains unexplained. It has been known for a long time that the hardness of these alloys is closely related to the rate of cooling, Similar changes have been observed in the binary gold-copper system,6 one alloy of which corresponding to the formula Cu3Au, has been the subject of a careful and competent report by the English investigators, Sykes and Evans.7 They have established the fact that the shift of atoms from the ordered to the disordered condition takes place in some critical temperature range. At temperatures above the critical range the structure is random, and at temperatures below it the structure is ordered. No difference between these two structures is revealed by the microscope. Both have a face-centered cubic lattice and complete solubility, so that there is no evidence to suggest that the changes in properties are associated with a phase change, The more slowly the alloy is cooled, the higher is the degree to which the ordering process proceeds and the more marked is the increase in hardness. As experimental data were accumulated on 14-carat gold alloys, several contradictions arose. Certain observations tended to confirm the existence of a superstructure, while other observations seemed to be inconsistent with such a transformation. PRESENT INVESTIGATION As a focal point about which to develop this subject, it is expedient to consider first

Jan 1, 1943

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

Factors leading to the necessity for some individual testwork in solving most specific hydraulic transportation problems are listed and a description is given of a method used in determining critical flow conditions. An outline is given of the basic theory of the purpose of the testwork, and a means of applying test results for varied pipeline diamet.er and material conditions follows. Engineering and economic factors are applied to the solution of a specific hydraulic transportation problem and the use of the test results in plant practice is illustrated. The advantages of connecting pumps in series in centralised pumping stations rather than individually along the pipeline are stressed. Some notes are added on the future possibilities and economies of post pump injection of solids into high pressure pipelines.THE HYDRAULIC TRANSPORTATION OF SANDSAs well as all the classical variables involved in a pipeline installation, one must consider, when solids are to be transported, the effects of such variables as:(i) Proportion of solids in the pulp.(ii) The average specific gravity of the pulp.(iii) Specific gravity of the solid material.(iv) Solid particle average sizing and possibly shape.(v) Solids particle grading.(vi) Pipeline diameter for effects other than classically hydraulic.(vii) Pipeline material.(viii) Fluid viscosity.(ix) Pump characteristics.(x) Abrasive or corrosive properties of the pulp.Not surprisingly, the application of published data to the hydraulic transportation of a specific material is difficult if not well nigh impossible. Most hydraulic transportation investigations also involve economic and site factors vary...

Jan 1, 1959

The only economically significant deposit of dolomite in New Zealand is at Mount Burnett, in north-west Nelson. The dolomite, associated with marbles and schists, is complexly deformed, and is of Paleozoic age.A very large quantity is present, although the recoverable amount is to some extent limited by the difficult terrain.Physically the quality of the dolomite is excellent. It is a tough, durable, fine grained rock. Chemically it is a little more variable. The range and frequency o~ the more important impurities are illustrated by hlstograms, as is the &quot;dolomite factor&quot;-a measure of the amount of the mineral dolomite in the rock. lbe dolomite factor averages 84 per cent, the remainder of the rock consisting largely of calcite. Quarrying, milling, production, and uses are described. In 1966 production reached 13,250 tons.

Jan 1, 1969

By René Lefebvre

Numerical simulations of the physicochemical processes related to acid rock drainage (ARD) in the Sugar Shack South rock pile of the Questa Mine were performed with the TOUGH AMD simulator. The objectives were to 1) identify the main processes responsible for observed present-day conditions, 2) provide an estimate of gas phase humidity transfer, and 3) give a preliminary indication of the potential impact of closure involving the installation of an alluvial soil cover. Modeling results indicated that the mine rock geometry (thin layers placed along steep mountain slopes) favors the onset of strong thermal air convection. Simulations also indicate that resloping the piles would not significantly reduce convection and oxidation. For simulation purposes, a potential cover with the permeability range of a local alluvium was investigated and found to be of questionable effectiveness since its permeability can exceed the value of 3x10-13 m2 required to prevent thermal air convection and reduce ARD.

Nov 1, 2002

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By R. F. Hinds

A pressurizing system was designed and built to apply a radial pressure of 5.000 psi to rock samples. Samples of the Bradford, Weir and Kirkwood sandstones were subjected to radial pressures parallel and perpendicular to the bedding in the system and the changes in conductivity, porosity and permeability were deter-mined. Asymptotic decreases in conductivity, porosity and Klinkenberg permeability were observed over the 0- to 3,500-psi range. From these data, the increase of formation factor over the same range was calculated. The cementation exponent expressed in the Archie equation was found to increase with pressu,re. The rate of change varied from formation to formation. Only small differences were observed for samples taken parallel to the bedding as comnared to those taken perpendicular to it except for the Bradford sand. Above 3,500 psi the data are not good enough to tell if the properties continue to fall-off asymptotically or in a different manner. A possible explanation for the probable litnit of the asymptotic rate around 3,500 to 4,500 psi is that this represents the maximum pressure which the formations have unrdergone during their geological life as a result of burial. INTRODUCTION For many years measurements have been made in the laboratory of the properties of oil-bearing sandstones with little consideration being given to whether these properties had been changed when the samples were moved from their original position in the ground to the laboratory. Relatively little has been reported in the literature on the effect of pressure on the properties of sandstones. The changes in permeability for eight typical consolidated oil-bearing sandstone samples with overburden pressure (0- to 15,000-psi range) was presented by Fatt and Davis&apos; in graphical form. In 1953 Fatt&apos; also reported the relationship between porosity and overburden pressure for four typical consolidated oil-bearing sandstone samples (0- to 5,000-psi range). Fatt later described the changes of formation factor and porosity of 20 typical oil-bearing sandstone samples with overburden pressure changes (0- to 5,000-psi range) giving the values of the coefficients and exponents in the Archie&apos; equation, and the more general Winsauer equation&apos;, where C, k and m are empirical constants, F is the formation factor, and + is the porosity. During the experiments of this investigation the core was contained in a neoprene rubber sleeve as shown in Fig. 1. It was held between two steel end members which were mounted in a steel cylinder. The unassembled pressure cylinder with its component parts is shown in Fig. 2. The core was insulated from the two steel end members by a Teflon sleeve with a small hole in the

By M. Keen

The backfill system at Cleveland Potash?s Boulby Mine places waste filter cake underground in the form of a high concentration slurry in worked out areas of the mine reducing the mine?s environmental impact. The backfill system delivers slurry approximately 1100 m down the mine and up to 11 000 m horizontally underground. The Boulby backfill system is unique in that the placed backfill waste is not used for the usual purposes such as support, pillar extraction or reducing ventilation requirements. It was specifically implemented for environmental reasons. This influenced the design and resulted in some unique features of the system. A previous paper (Wilkins et al., 2004) described the design and commissioning of the backfill system. This paper describes the operational experience with the backfill system and backfill placement since commissioning in May 2003 and looks at lessons that can be applied in other backfill designs.

May 1, 2007

By M. -C. Noël, G. P. Demopoulos

In this work the formation and environmental stabilization potential of arsenate-containing fluoroapatites is considered. In particular in this research various compounds were precipitated from synthetic solutions containing fluoride, arsenate/phosphate and calcium by varying different parameters-temperature, Ca:As ratio, pH, and P:As ratio, and aging time. The results obtained helped determine the operating window that should be used for the formation of highly crystalline fluoroapatites, in particular svabite (Ca5(AsO4)3F). It was found that svabite has a specific pH range of precipitation, with lower pH yielding CaF2 and calcium arsenate compounds such as CaHAsO4•H2O. At higher pH, a mixture of svabite and johnbaumite (Ca5(AsO4)3OH) precipitated, yielding a less stable material. This range of precipitation varied with the concentration of arsenic in the starting solution, and widened with higher initial concentrations of Ca2+, AsO4 3- and F-. Furthermore, svabite/fluoroapatite solid solutions were formed by using the same procedure as svabite but replacing some of the arsenate in solution by phosphate. The increase in phosphate content yielded a gradual change in morphology and crystallinity. Work on stability evaluation is currently under way.

Jan 1, 2014

By Grigor Mishev, Georgi Petrov, Benjamin Cebrian

Before designing a single blast or all the blasts on a pit level, it is critical to assess the main goal on each. To do this, a series of constraints must be taken into account: wall protection, vibration control, flyrock hazards, fragmentation required, desired displacement as well as economy, equipment efficiency. The tool to do this is the Blast Master Plan. Many mines fail to integrate on its elaboration key stakeholders such as planning, operations, geology/geotechnical and milling departments. Designs not only have to provide consistent behavior of the blasts, but have to make sense all in one with the geological and geotechnical conditions as a starting point. Once blasts are designed under an organized set of priorities, and complemented with quality controls, optimization is possible on a large scale.

Jan 1, 2016

By Bertram Price

Libby, Montana is the site of a large vermiculite deposit that was mined between 1920 and 1990 to extract vermiculite for commercial applications such as insulation, gardening products, and construction materials. The Libby vermiculite deposit also contains amphibole minerals including tremolite, actinolite, richterite, and winchite. Historically, Libby mine workers experienced high exposures to amphibole structures, and, as a group, have experienced the health consequences of those occupational exposures. It has been suggested that Libby residents also have been and continue to be exposed to amphibole structures released during the vermiculite mining operations and therefore are at increased risk for disease. The Agency for Toxic Substance and Disease Registry (ATSDR) conducted two epidemiological-type studies of residents living in Libby and the surrounding areas to assess these risks. The Environmental Protection Agency (EPA) collected and analyzed exposure data in Libby and used those data to project risks of asbestos-associated disease for Libby residents. The EPA has placed the Libby Asbestos Site, which includes the mine and the town of Libby, on its National Priority List of hazardous waste sites in need of clean up. This article presents a review of the exposure studies conducted in Libby and an analysis of health risks based on the data collected in those studies. Libby mine workers have experienced elevated levels of asbestos-associated disease as a consequence of their occupational exposures to amphibole structures. Libby residents? exposures typically are substantially lower than mine workers? historical exposures, and the health risk projections for residents are, accordingly, substantially lower. © 2007 Published by Elsevier Inc. Keywords: Libby; Montana; Vermiculite; Amphibole minerals; Asbestos; Asbestos-associated disease

Jan 1, 2007

By David Newman

In Eastern Kentucky, the Darby seam has had an extensive history of coal bumps and pillar bursts. The combination of high overburden, strong rock and coal, subjacent and superjacent mines, and retreat mining has produced incidences of violent pillar failure. The influence of these factors on pillar stability and the potential to bump is illustrated in two case histories. In the first case history, a bump occurred unexpectedly during the retreat mining of a five heading continuous haulage panel. Alternative cut sequences and pillar dimensions were analyzed to identify a geometry that would reduce the potential for future coal bumps or bounces during retreat mining. The viability of the alternatives was constrained by the reach of the continuous haulage system, the overburden depth, and the presence of thick sandstones in the main roof. Each alternative was numerically modeled cut-by-cut to examine the mechanism of stress transfer, as a pillar row is retreat mined. This approach highlighted which cuts were being made in highly stressed portions of a pillar and therefore more prone to coal outbursts. Validation of the numerical modeling was accomplished by comparing the cuts where bumps and outbursts had occurred underground to the highly stressed cuts shown within the models. Recommendations of the barrier pillar width between adjacent panels, pillar dimensions, and changes in the retreat mining sequence were proposed based upon the overburden thickness, geology, and the result of the numerical modeling. The second case history documents a nine-entry panel 3,600-feet long that was retreat mined a distance of 2,064-feet without a significant roof fall or roof-floor convergence. Mine management became concerned about the potential for a coal bump or a large roof collapse within the gob and the resulting air blast. The stress on the pillar line and within the remnant pillars in the gob was quantified through numerical modeling. Changes in mining practices on the current panel were implemented to avoid a bump in the active panel. A barrier was established between the current and the future panels to protect the future panel against abutment pressures from the void area. A change in pillar centers was proposed in the adjacent panel to absorb the side abutment pressure from the gob of the active panel.

Jan 1, 2008

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018