Search Documents

By Musa Karakus

Ceramic build-ups are synthetic mineral deposits formed in critical locations in or near the throats of inductor units in channel induction furnaces, the preferred melting and holding furnaces used in iron foundries. The build-ups are undesirable because they slow down melt circulation, increase power consumption and cost. and decrease the quality of the metal. This study involved the determination of the mineralogy of build-up samples and the quantitative measurement of phase abundance in those build-ups by cathodoluminescence microscopy. These undesirable deposits usually are hard and dense and contain variable amounts of entrained metallic iron. The non-metallic phases dominantly consist of oxides and silicates of several refractory elements, AI, Mg. Ca, Si, and Fe. Minor amounts of the sulfides of Ca. Mg, Fe and REE elements, especially Ce and La. and the oxides and silicates of Ce and La elements are locally present in the build-ups. The build-up samples were found to be ideally suited for study by cathodoluminescence, which has provided an easy means for rapid re-cognition of the phases present in the build-ups. The phase compositions were determined by electron microprobe analysis. The phases identified and their characteristic cathodoluminescence shown in the ceramic build-up samples were: spinel (bright green, blue-green, and red). forsterite (red and purple), periclase (dark reddish-brown, blue. and orange), corundum (red, blue, orange, and white), anorthite (yellow, yellow-green, blue, and blue-purple), hibonite or calcium hexaluminate (dark green), mullite (dull red-brown), gehlenite (deep blue), silica(dark brown, pink, purple, red. and blue), monticellite (light violet blue and light pale yellow-orange), silicon carbide (orange), oldhamite (bright yellow and orange). Ce-La silicate phases (purple), and glass (orange, dull red, and purple). Non-luminescent phases were: hercynite, Fe-oxides, Ce-La-oxides, Fe-sulfides, and metallic iron.

Jan 1, 1989

By Guohua Bai, Yuanbo Zhang, Guihong Han, Zijian Su, Daoyuan Zhang

"Specularite ores have poor hydrophilicity and ballability as well as inferior high-temperature reactivity, which restrict the large-scale application of them in the pelletizing and sintering production. Modified humic acid (MHA) organic binders are firstly used for pellet preparation from specularite in this paper. The results show that the drop strength of green pellets is 3.7 times/0.5m and compression strength is 12.5 N/P by using 1.0 wt% MHA as binder. Under the optimal experimental conditions of preheating temperature 980 °C, preheating time 12 min, roasting temperature 1280 °C and roasting time 10 min, the preheated pellets have the compression strength more than 400 N/P, and that of roasted pellets is 2747 N/P. The strength of finished pellets meets the requirements of blast furnace iron-making. MHA is a kind of more effective organic binder for specularite pellets compared with the inorganic bentonite.IntroductionAcid Pellets have advantages of good strength, uniformity particle size, high iron grade and good reducibility, which can be used as high-quality burdens for blast furnaces [1]. With fast development of Chinese iron and steel industry domestic magnetite concentrates with high grade of iron and good firing performances become shortage.Imported specularite ores have advantages of low price and high grade of iron (generally above 67 wt%), so the application of them in pellets is an effective way for sustainable development of pellet industry in China. However, the specularites have not been utilized in pelletizing and sintering at present because of the poor ballability and high-temperature reactivity [2, 3]. Most of the pellet plants use bentonite as binders, the amount of which is about 2~3 wt%. The pellet production practice shows that 90 wt% bentonite is still residual in finished pellets and reduces the iron grade [3]. Developing a new organic binder instead of bentonite is very important to the high-quality pellet production. On one hand, the consumption of bentonite is obviously reduced, resulting in decreasing the ironmaking coke ratio and slag discharge; On the other hand, the iron grade of finished pellets are improved, which brings the benefit for the ironmaking production."

Jan 1, 2011

By Messias dos Santos Machado, Renato B. Godoy, Roberta Lima, Andressa Silva, Francisco Valenzuela-Díaz, Rene R. Oliveira, Esperidiana Moura

This work aims to incorporate the Bof White Clay, from Boa Vista, Paraiba State, Brazil, as natural nanofiller in Ehylene vinyl alcohol copolymer (EVOH) and obtain flexible films. Nanocomposite was obtained using a twin-screw extruder, and film formed using a blow extruder machine. The flexible film nanocomposite was characterized, by tensile tests, XRD, DSC and their properties were evaluated. The results showed a good interaction between the clay and the EVOH resulting in an increase of properties of films nanocomposites as compared to films neat polymer.

Jan 1, 2015

By Zhihe Dou, Yan Li, Qiuyue Zhao, Guozhi Lv, Yan Liu, Hongliang Zhao

"Abstract: How to reduce carbon dioxide emissions has become a vexing problem, meanwhile, there exist high energy consumption and low efficiency problems in the existing CO2 capture and storage technologies. For CO2 comprehensive Utilization, this paper researches a new technology of absorbing the CO2 emission with high alkaline calcium or high alkaline wastewater sludge mineralization of calcium and invent a core device for multi-level jet carbonation. The industrial test has been carried out in China Xinyu slag Engineering Co., Ltd. The wastewater flow is 150m3/h in the pilot scale. The prepared calcium carbonate has a whiteness greater than 90%, particle size less than 150nm. The mineralization of aluminum exhaust with waste carbide indicates that the CO2 absorption rate is greater than 99.0%, CO2 concentration in the exhaust gas is lower than 0.08%, the purity of mineralized calcium carbonate is greater than 99.0% and particle size is less than 100 nm.InstructionAccording to the statistic data from IEA (2009), the carbon dioxide discharge from fossil fuel consumption in China has exceeded it in the US by the year of 2007, China, has become the largest emitter of carbon dioxide all over the world. Meanwhile, the economic scale is still on an increasing trend in the next 50-100 years, leading to a continuous increment in carbon dioxide discharge. According to the international energy agency forecasts, the energy-relative CO2 discharge in China will rise to 11,615 million tons, 91.3% higher than it in 2007. In the year of 2012, the CO2 gross discharge has reached 10,000 million tons, obviously higher than the predicted value. It is a tremendous task to reduce the emission. Non-ferrous metals industry is one of the largest emitters of carbon dioxide among the industrial circle, the whole industry might discharge a huge amount of carbon dioxide (over 600 million tons), in which the electrolytic aluminum industry is the largest energy consuming industry and CO2 emitter. At present, the CO2 discharge has focused by the whole world due to the environmental problems it causes; meanwhile, supplement of new carbon source is needed due to the exhausting oil and coal resources, so that various countries in the world are attaching importance of the recycle and purification of CO2. Many countries are studying on the cyclic utilization of carbon dioxide. Gas CO2 is mainly applied in chemical, pharmaceutical raw materials, beverage filling agent, refrigerant, inert medium, solvents, pressure source, the welding protective gas, antioxidant and fire extinguishing agent, etc. Solid CO2 is mainly applied in penicillin production, fish, cream, ice cream and other food storage and transportation at low temperature, etc. nowadays, such methods as absorption method, membrane separation, adsorption, etc. are widely used to recycle CO2, with such problems as high investment cost and technical constraints etc."

Jan 1, 2014

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in at flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don't assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the prediction of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace The results show that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By Guanghui Li

Nickel pig iron (NPI), used as a substitute for electrolytic nickel, is able to reduce the production cost of stainless steel greatly. Aiming for preparing NPI from nickeliferous laterite ore, a pilot-plant scale test of coal-based rotary kiln direct reduction of laterite ore was performed and reported in this study. In this process, the ground laterite sample (18.85% TFe and 1.52% Ni) mixed with additives, pulverized coal and binder was briquetted into briquettes with the size of 40mm×40mm×31mm, laterite ore briquettes and reducing coal were charged into a rotary kiln with the diameter of 1.6 m and the length of 16 m, for a retention period of 6~7 hours, in which reduction section temperature was ranging from 950~1050 oC. The reduced briquettes were water quenched, ball mill ground and beneficated via low intensity magnetic separation. A magnetic concentrate, Ferronickel powder, with 86.9% TFe and 8.0% Ni was obtained, and the corresponding magnetic recovery of iron and nickel are 75% and 96.3%, respectively.

Jan 1, 2014

By V. Ramachandran

Under the Resource Conservation and Recovery ACT (RCRA), generators of listed or characteristic hazardous wastes must find satisfactory means for disposal. of wastes. Initially, for many this meant landfills and deep-well injection. Until recently, mining and metallurgical by-products have largely been exempt from RCRA, but now are coming under its jurisdiction. With the increasing closures of landfills, companies in the U.S. such as electroplaters, miners, metallurgical plants and others are turning to recycling as an alternative to treat their wastes. While the cost of recycling has been challenging, the long-term economics prove attractive because recycling interrupts the cradle- to-grave responsibility for the waste generator. The present paper describes the recycling of hazardous wastes at ENCYCLE/TEXAS. Encycle extracts marketable metals from metal-bearing sludges and wastewater using hydrometallurgical processes borrowed from the mining and metallurgical industry.

Jan 1, 1994

By Ivo André

Sorption of copper ions from aqueous solutions by dried biomass of the aquatic plant Potamogeton luscens was studied at laboratory scale. The aquatic plant was collected in water resources in Brazil, washed, dried at 60°C and ground in a bladed mixer. Sorption experiments were conducted in agitated flasks and in a packed bed column. Maximum copper removal was obtained between pH 5.0 and 6.6 when copper was present in the ionic form Cu'. Sorption followed the Langmuir isotherm with saturation attained at 35 mg/g. Free energy of sorption was found, to be of the order of -25 kJ/mol. Sorption kinetics data were better described by a second order reaction and rate constants were calculated in 0.030 1/(min.mg) for - 4.0 mm particles and 0.081 1/(min.mg) for - 0.59 mm particles. Removal of metal ions in a packed bed column showed that Potamogeton luscens biomass can be used in several sorption/dessorption cycles. After sorbent saturation, copper ions can be recovered from the loaded biomass by elution-with H2SO4, solution. Main mechanism responsible for heavy metal uptake was found to be ion exchange. Results are discussed in terms of the surface properties of the biomaterial, solution chemistry of copper ions and thermodynamics parameters.

Jan 1, 1995

By David R. Brosnahan

Increased Cu grades due to chalcopyrite-rich ore from The Doe Run Company's new Casteel Mine prompted a program to increase Cu recovery. Preliminary tests indicated that prohibitive quantities of FeS2 float with chalcopyrite. Point counting of mill stream samples showed that locking was not a major problem, although grinding to finer particle size enhanced the floatability of both chalcopyrite and marcasite. Backscattered electron images and microprobe analyses of FeSz minerals revealed the presence of Pb which appears to occur as solid solution in marcasite, and as a sub-micron particulate Pb phase in pyrite.

Jan 1, 1987

By Eric Klaffenbach

Valorization of slag from metallurgical industrial processes becomes ever more important as this may help optimizing and reducing the use of natural resources such as rock and sand. In view of this objective, metallurgical processes have to be analyzed in order to modify the slag composition so that it will meet the expected requirements of potential users of these resources. This paper gives the results of a thermodynamic analysis of the flash smelting process to understand the impact of operational parameters on slag chemistry and elemental partitioning in the process. It is shown that an increase of the matte grade and temperature leads to higher deportment of Pb, Zn and As to the slag. With increasing matte grade the volatilization of these elements decreases. Furthermore, the results indicate an increasing solubility of Cu and S in slag at higher temperatures.

By Joerg Hammerschmidt, Marcus Runkel, Andreas Wirtz, Kent Pope

"Fluidized bed reactor systems in the minerals industry have been progressively developed and widely implemented over a period of more than sixty years for a multitude of process applications. Their versatility is manifested in calcining, roasting and combustion treatment of minerals including solid fuels. Experiences from metallurgical processes have expanded to new applications in the oil shale processing, biomass combustion and renewable energy sector. This paper focuses on the most important aspects of fluidized bed technology for a variety of Outotec processes. Energy recovery is a major topic for all applications and will be addressed, as well as environmental aspects, particularly regarding the off-gas treatment. Outotec is one of the pioneers of roasting and the fluidized bed process including gas cleaning and sulphuric acid production where applicable. Process development is strongly supported by significant investment in R&D, thus enabling process adaptation and scale-up to meet specific customer/market requirements.Introduction to Fluidized Bed TechnologyThe early days of fluidized bed technology were characterized by the use of bubbling fluidized bed reactors (BFB). This technology was popular for roasting zinc and copper ores. The introduction of circulating fluidized bed technology led to increased plant capacities and improved process control for the traditional processes. Furthermore, the technology has been applied in many other industries, including the renewable energy industry, which will be part of this design and process comparison. The paper starts out with the fundamentals on particle fluidization as the main common design parameter, leading to the importance of heat recovery and offgas treatment.In fluidized reactor systems, the particle concentrations can reach several hundred kilograms per cubic meter of fluidization gas. This high solid concentration leads to large surface areas and enables direct contact of gas molecules with particle surface molecules. Excellent conditions for enhanced heat and mass transfer thus provide nearly ""ideal"" heat exchange conditions and better reaction kinetics. The bubbling bed exhibits a better heat transfer coefficient within the bed in comparison to the circulating fluidized bed (CFB). The different conditions of gas velocities and solid concentrations allowing the classification of fluidization reaction regimes are shown in the Reh diagram in Figure 1."

Jan 1, 2014

By R. C. Nascimento

It was investigated the effect of the addition of bentonite on the physical propertiesof pellets produced from fines of manganese ores. Cold-bonded pellets were produced. Pellets bearing up to 1 wt% of bentonite were submitted to strength compression resistance tests, fatigue of pellets to impact and maximum height of fall tests. A correlation of resistance of the pellets and time for curing were stablished. The produced pellets match the conditions for raw materials used in electric smelting hrnaces to produce manganese based ferro-alloys.

Jan 1, 1995

By Baojun Zhao, Zhixiang Cui, Zhi Wang

"Bottom blown oxygen copper smelting process has been developed in Dongying, China by Dongying Fangyuan Nonferrous Metals Co., Ltd. in commercial scale. This is the first modem copper smelting technology developed in China with the advantages of high oxygen enrichment, low temperature and autothermal operation. Production capacity of more than 100,000 tonnes per year of copper has been achieved through a single bottom blown oxygen furnace with instantaneous feed rates reaching up to 90 t/h. The main features of the bottom blowing smelting process are that high grade matte (up to 72 wt% Cu) can be produced at relatively low temperatures with 2-3 wt% Cu remaining in the smelting slag. Analyses of quenched smelting slag show that significant amount of magnetite crystals are present in the slags at operating temperature which indicates that the operating temperature was much lower than the liquidus temperature of the slag. After four years operation this new technology has shown great potential for expanding production capability and energy saving. Process development continues on the first commercial scale bottom blown furnace at Dongying Fangyuan Nonferrous Metals and a larger bottom blown smelting furnace is under construction.IntroductionFlash and bath smelting technologies are the major processes used in modem copper making industry [l]. Ausmelt/Isasmelt using top blown and Noranda/Teniente using side blown are typical and common bath smelting technologies. In 1980s-1990s Hunan Shuikoshan Mineral Bureau, jointly with China Nonferrous Engineering and Research Institute (now China Enfi Engineering Corp.), developed the concepts of the bottom blown oxygen processes for both lead and copper smelting [2]. After the pilot test on 3000 ton copper per year scale in 1991, it was not progressed to industrial scope."

Jan 1, 2013

By Markku Rytkonen, Shaolong Chen, Ilpo Kylmäkorpi, Hannu Mansikkaviita

Though the Peirce Smith (P-S) converter is a traditional type of furnace, continuous improvement in its mechanical and electrical design is still Kumera's approach. Efforts are made particularly on the following aspects: converter head shape for easy fabrication and structural strengthening, oxidation air swivel joint for low pressure drop and low noise level, wind box for even air distribution to tuyeres, drive unit and its control for reliable and handy operation. These improvements have successfully been applied in recent P-S converter deliveries.

Jan 1, 2009

By Jinxing Ji

Several fundamental aspects related to the nickel electrowinning from chloride electrolytes have been addressed in this paper. The thermodynamic study includes the activity coefficient of the hydrogen ion and the speciation diagram of NiCI2 solutions. The activity coefficient of the hydrogen ion (YH+) was calculated and estimated experimentally using a combination glass pH electrode. It was found that YH+ was greater than one in concentrated NiCl2 solutions and increased significantly with increasing NiCl2 concentration. The speciation diagram for NiCl2 solutions was plotted with YH+ and the effect of the ionic strength on the equilibrium constants being taken into account. It was discovered that the predominant nickel species in the acidic region were Ni2+ and NiCI+ in 0.937 M NiCl2 solution at 25°C. Electrodeposition tests demonstrated that higher Nit' concentration in the electrolyte improved the current efficiency of nickel electrodeposition (CENi). The additions of H3BO3, and NH4Cl increased very little the current efficiency of nickel electrodeposition at pH 1.5 and temperature 60°C. However, the addition of sulfate decreased the current efficiency of nickel electrodeposition. Nickel electrodeposition was also found to be a steady-state process since the amount of acid added to the electrolyte at a constant pH increased linearly with time during galvanostatic electrodeposition. The cathode surface pH during nickel electrodeposition was measured using a flat-bottom combination glass pH electrode and a 500-mesh gold gauze as cathode. The cathode surface pH was found always to be higher than the pH in the bulk electrolyte, and if the current density was sufficiently large, it would eventually reach a level causing precipitation of insoluble Ni(OH)2(s) on the cathode surface. Rotating disc electrode studies revealed that the rate of nickel electrodeposition was first order with respect to the activity of nickel ion and zero order with respect to the activities of chloride and hydrogen ions. The rate of hydrogen evolution was found to be first order with respect to the activity of hydrogen ion and to be zero order with respect to the activities of nickel and chloride ions. These findings indicate that nickel deposition and hydrogen evolution proceed independently.

Jan 1, 1995

By V. I. Lakshmanan, R. Roy

Base metals and PGMs are currently recovered from sulfide concentrates using pyrometallurgical processes. These processes suffer from several limitations such as being capital intensive, scaling problems, S02 emissions and long delay in value recognition. Alternative hydrometallurgical technologies have so far not been successful and currently total pressure oxidation and partial pressure oxidation hydrometallurgical technologies are being evaluated. Process Research ORTECH has developed a unique hydrometallurgical process to recover base metals and precious metals using mixed chloride technology. In a first stage leach, base metals are recovered and elemental sulfur is liberated from hydrogen sulfide formed during this leaching stage. During second stage leach, precious metals are recovered using proven separation technologies. Some of the advantages of the process are the recovery of elemental sulfur from sulfide sulfur, recycle of the chloride lixiviant thereby eliminating effluent treatment steps and use of excess energy from the Claus reactor for the pyrohydrolysis step.

Jan 1, 2011

By Sebastian Schmuck, Petrico von Schweinichen, Dieter Senk, Mohammad Peymandar

"At Department of Ferrous Metallurgy of the RWTH Aachen University in Germany steels in the system Fe-Mn-C(-Al) are investigated and produced in the framework of the SFB 761 ""steel-ab initio"". A new world of steel grades leads to special challenges regarding the production and recycling at the end-of-life cycle of product. In order to recycle high manganese steel alloys the EAF has to be chosen preferentially. A good slag practice is necessary avoiding loss of manganese content during melting in the EAF. This paper investigates on the reaction kinetics at the interface of slag and steel containing Mn (17-22 wt.-%) and up to 3 wt.-% Al. The effect of changes in the composition of slag and steel on the interfacial reaction kinetics is studied. The thermodynamic software FactSage™ is utilized to calculate the composition of slag and steel at equilibrium.IntroductionTRIP and TWIP steels are highly alloyed steels which show superior strength and ductility when compared to standard carbon steel and stainless steel alloys. These TRIP- and TWIPsteel grades contain typically 15-30 wt.-% manganese, 0-4 wt.-% silicon and aluminum, and up to 1 wt.-% carbon. Steels containing 18-28 wt.-% manganese and 0.7-1.2 wt.-% carbon together with aluminum addition from 3 to 12 wt. -% and without silicon refer to TRIPLEX high manganese steel alloys. These alloys combine high strength at even large ductility [ 1-4]. At the Department of Ferrous Metallurgy (IEHK) of the RWTH Aachen University in Germany, steels in the system Fe-Mn-C(-Al) is under investigation at the collaborative research center, SFB 761 ""Steel-ab initio"". In this project, high manganese alloyed TRIP and TWIP steels are in the focus.The mechanical properties such as high strength and high ductility make this kind of steels perfect candidates for impact absorption applications in auto body such as vehicle doors and bumpers [2, 5]. With increasing the use of TRIP-, TWIP- and TRIPLEX-steels more high manganese steel scraps will be available at the end of life cycle of products, which need to develop the technologies and metallurgical processes to recovery of high manganese steel. A new steel grade brings new challenges in recycling. In order to recycle high manganese steel scraps the electric arc furnaces (EAF) have to be chosen preferentially [1]. Nevertheless it's not easy to prevent the manganese loss during the process in EAF. During the oxygen refining of high manganese molten steel in EAF the manganese content decreases strongly by oxidation and vaporization, which is affected by slag composition, slag properties such as basicity and viscosity, slag weight as well as melt temperature [6-8]."

Jan 1, 2014

By Guo Chen, Jin Chen, Jinhui Peng

"In this paper, the methods of life cycle assessment for microwave hot air systems, and the concept of green degree were proposed. Greenness evaluation index, evaluation system and evaluation model of microwave hot air systems were established. Also, life cycle assessment processing based on these ideas was introduced. Analytic hierarchy process and fuzzy decision- making method were utilized to establish and solve the greenness evaluation of assessment model, while the scores of green degree in microwave hot air systems were obtained. The results show that Life cycle assessment can be applied effectively and efficiently to the microwave hot air systems.IntroductionHot air systems are an important industrial operation condition, which is used to provide high temperature air for materials processing. Nowadays, high temperature airs are manufactured by the conventional heating processes, in which some ceramic materials are used as heating materials. However, these processes pollute the environment. Therefore, to explore new method to produce high temperature air with low energy consumption and less environment pollution are necessary.Microwaves are now being used in various technological and scientific fields in order to heat dielectric materials [1]. Microwaves irradiation has been explored in materials processing in recent years [2-3]. The main advantage of using microwave heating is that the treatment time can be considerably reduced, which in many cases represents a reduction in the energy consumption as well. Since there is energy absorption but no heat conduction, the heating is very rapid and highly efficient, resulting in energy savings and the shortened processing time [2, 4]. Compared with conventional heating techniques, the additional advantage of using microwave irradiation is that microwave irradiation achieves both internal and uniform heating [5-7]. In addition, it is more convenient to control the microwave irradiation processing, because of no direct contact between the heating source and heated materials with less equipment size and waste [2, 8-9]. Life cycle assessment is used and accepted methods for the evaluation of the environmental impacts of products or systems [10]. Recently, many appropriate evaluation methods have been developed for life cycle assessment [11-12]. These proposed methods usually are employed for the evaluating product and analyzing results [13]. Among them, the analytic hierarchy process and the fuzzy comprehensive evaluation stand out as a popular method utilized in many fields [14-16]. Analytic hierarchy process and fuzzy comprehensive evaluation are a combination of mathematical and statistical technique that is useful for analyzing the effects of several independent assessment aspects on the system goal without the need of the predetermined relationship between the objective function and the assessment aspects [17-19]."

Jan 1, 2013

By Ivan Imris

The iron production has generated many tonnes of very fine residues with high concentration of iron. In addition, during the recycling of galvanised steel scrap in the steel making processes the zinc and lead are largely concentrated in the dust. These kinds of dusts are usually dumped beside the metallurgical plants and cause environmental problems. Therefore the metal recovery from the metallurgical residues has become a major interest not only from the viewpoint of metals recycling but mainly from the viewpoint of environmental land protection. The thermodynamic analyses and laboratory experiments suggested that the metals could be recovered from metallurgical wastes by reduction roasting and by plasma smelting processes. The iron rich pellets with very high metallization may be obtained from metallurgical wastes by the reduction roasting and the inert slag and pig iron could be produced by plasma smelting processes. In both cases the iron rich products are suitable for the steel production. During the reduction roasting or plasma smelting the high volatile zinc and lead metals were removed and enriched as a secondary dust, Zn-Pb concentrate, which is suitable for processing in zinc and lead smelters. Suggested processes are commercially feasible and environmentally friendly without any solid or liquid waste.

Jan 1, 2003

By Antoine Allanore, Guillaume Lambotte, Bradley R. Nakanishi

Current industrial methods used for rare earth element (REE) extraction involve: 1) ore enrichment, 2) separation of rare earth oxides (REOs), 3) chlorination or hydrofluorination, and 4) individual electrowinning of REEs from a molten halide electrolyte. The complexity of REE extraction is inherited from their electronic configuration. Recently, molten oxide electrolysis (MOE) has been used to produce reactive metals directly from their oxides, e.g. titanium. As a single-step alternative to processes 3) and 4), or laboratory has investigated rare earth extraction by MOE. A key challenge is to find a molten electrolyte more stable than REOs. One possibility is to use binaries of REOs directly as a solvent. We have, therefore, developed two experimental approaches for studying molten REOs at temperatures exceeding 2200oC. The present work reports the most recent experimental results obtained with La2O3-Y2O3. Those promising results demonstrate potential for operating with molten REOs and refine the underlying materials challenge for electrodes to enable metal recovery.

Jan 1, 2015